// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * (c) 1997-1998  Grant R. Guenther <grant@torque.net>
 *
 * epia.c is a low-level protocol driver for Shuttle Technologies
 * EPIA parallel to IDE adapter chip.  This device is now obsolete
 * and has been replaced with the EPAT chip, which is supported
 * by epat.c, however, some devices based on EPIA are still
 * available.
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/wait.h>
#include <asm/io.h>
#include "pata_parport.h"

/*
 * mode codes:  0  nybble reads on port 1, 8-bit writes
 *		1  5/3 reads on ports 1 & 2, 8-bit writes
 *		2  8-bit reads and writes
 *		3  8-bit EPP mode
 *		4  16-bit EPP
 *		5  32-bit EPP
 */

#define j44(a, b)	(((a >> 4) & 0x0f) + (b & 0xf0))
#define j53(a, b)	(((a >> 3) & 0x1f) + ((b << 4) & 0xe0))

/*
 * cont =  0   IDE register file
 * cont =  1   IDE control registers
 */
static int cont_map[2] = { 0, 0x80 };

static int epia_read_regr(struct pi_adapter *pi, int cont, int regr)
{
	int a, b, r;

	regr += cont_map[cont];

	switch (pi->mode)  {
	case 0:
		r = regr ^ 0x39;
		w0(r); w2(1); w2(3); w0(r);
		a = r1(); w2(1); b = r1(); w2(4);
		return j44(a, b);
	case 1:
		r = regr ^ 0x31;
		w0(r); w2(1); w0(r & 0x37);
		w2(3); w2(5); w0(r | 0xf0);
		a = r1(); b = r2(); w2(4);
		return j53(a, b);
	case 2:
		r = regr^0x29;
		w0(r); w2(1); w2(0X21); w2(0x23);
		a = r0(); w2(4);
		return a;
	case 3:
	case 4:
	case 5:
		w3(regr); w2(0x24); a = r4(); w2(4);
		return a;
	}

	return -1;
}

static void epia_write_regr(struct pi_adapter *pi, int cont, int regr, int val)
{
	int  r;

	regr += cont_map[cont];

	switch (pi->mode)  {
	case 0:
	case 1:
	case 2:
		r = regr ^ 0x19;
		w0(r); w2(1); w0(val); w2(3); w2(4);
		break;
	case 3:
	case 4:
	case 5:
		r = regr ^ 0x40;
		w3(r); w4(val); w2(4);
		break;
	}
}

#define WR(r, v)	epia_write_regr(pi, 0, r, v)
#define RR(r)		epia_read_regr(pi, 0, r)

/*
 * The use of register 0x84 is entirely unclear - it seems to control
 * some EPP counters ...  currently we know about 3 different block
 * sizes:  the standard 512 byte reads and writes, 12 byte writes and
 * 2048 byte reads (the last two being used in the CDrom drivers.
 */
static void epia_connect(struct pi_adapter *pi)
{
	pi->saved_r0 = r0();
	pi->saved_r2 = r2();

	w2(4); w0(0xa0); w0(0x50); w0(0xc0); w0(0x30); w0(0xa0); w0(0);
	w2(1); w2(4);
	if (pi->mode >= 3) {
		w0(0xa); w2(1); w2(4); w0(0x82); w2(4); w2(0xc); w2(4);
		w2(0x24); w2(0x26); w2(4);
	}
	WR(0x86, 8);
}

static void epia_disconnect(struct pi_adapter *pi)
{
	/* WR(0x84,0x10); */
	w0(pi->saved_r0);
	w2(1); w2(4);
	w0(pi->saved_r0);
	w2(pi->saved_r2);
}

static void epia_read_block(struct pi_adapter *pi, char *buf, int count)

{
	int k, ph, a, b;

	switch (pi->mode) {
	case 0:
		w0(0x81); w2(1); w2(3); w0(0xc1);
		ph = 1;
		for (k = 0; k < count; k++) {
			w2(2+ph); a = r1();
			w2(4+ph); b = r1();
			buf[k] = j44(a, b);
			ph = 1 - ph;
		}
		w0(0); w2(4);
		break;
	case 1:
		w0(0x91); w2(1); w0(0x10); w2(3);
		w0(0x51); w2(5); w0(0xd1);
		ph = 1;
		for (k = 0; k < count; k++) {
			w2(4 + ph);
			a = r1(); b = r2();
			buf[k] = j53(a, b);
			ph = 1 - ph;
		}
		w0(0); w2(4);
		break;
	case 2:
		w0(0x89); w2(1); w2(0x23); w2(0x21);
		ph = 1;
		for (k = 0; k < count; k++) {
			w2(0x24 + ph);
			buf[k] = r0();
			ph = 1 - ph;
		}
		w2(6); w2(4);
		break;
	case 3:
		if (count > 512)
			WR(0x84, 3);
		w3(0); w2(0x24);
		for (k = 0; k < count; k++)
			buf[k] = r4();
		w2(4); WR(0x84, 0);
		break;
	case 4:
		if (count > 512)
			WR(0x84, 3);
		w3(0); w2(0x24);
		for (k = 0; k < count / 2; k++)
			((u16 *)buf)[k] = r4w();
		w2(4); WR(0x84, 0);
		break;
	case 5:
		if (count > 512)
			WR(0x84, 3);
		w3(0); w2(0x24);
		for (k = 0; k < count / 4; k++)
			((u32 *)buf)[k] = r4l();
		w2(4); WR(0x84, 0);
		break;
	}
}

static void epia_write_block(struct pi_adapter *pi, char *buf, int count)
{
	int ph, k, last, d;

	switch (pi->mode) {
	case 0:
	case 1:
	case 2:
		w0(0xa1); w2(1); w2(3); w2(1); w2(5);
		ph = 0;  last = 0x8000;
		for (k = 0; k < count; k++) {
			d = buf[k];
			if (d != last) {
				last = d;
				w0(d);
			}
			w2(4 + ph);
			ph = 1 - ph;
		}
		w2(7); w2(4);
		break;
	case 3:
		if (count < 512)
			WR(0x84, 1);
		w3(0x40);
		for (k = 0; k < count; k++)
			w4(buf[k]);
		if (count < 512)
			WR(0x84, 0);
		break;
	case 4:
		if (count < 512)
			WR(0x84, 1);
		w3(0x40);
		for (k = 0; k < count / 2; k++)
			w4w(((u16 *)buf)[k]);
		if (count < 512)
			WR(0x84, 0);
		break;
	case 5:
		if (count < 512)
			WR(0x84, 1);
		w3(0x40);
		for (k = 0; k < count / 4; k++)
			w4l(((u32 *)buf)[k]);
		if (count < 512)
			WR(0x84, 0);
		break;
	}
}

static int epia_test_proto(struct pi_adapter *pi)
{
	int j, k, f;
	int e[2] = { 0, 0 };
	char scratch[512];

	epia_connect(pi);
	for (j = 0; j < 2; j++) {
		WR(6, 0xa0 + j * 0x10);
		for (k = 0; k < 256; k++) {
			WR(2, k ^ 0xaa);
			WR(3, k ^ 0x55);
			if (RR(2) != (k ^ 0xaa))
				e[j]++;
		}
		WR(2, 1); WR(3, 1);
	}
	epia_disconnect(pi);

	f = 0;
	epia_connect(pi);
	WR(0x84, 8);
	epia_read_block(pi, scratch, 512);
	for (k = 0; k < 256; k++) {
		if ((scratch[2 * k] & 0xff) != ((k + 1) & 0xff))
			f++;
		if ((scratch[2 * k + 1] & 0xff) != ((-2 - k) & 0xff))
			f++;
	}
	WR(0x84, 0);
	epia_disconnect(pi);

	dev_dbg(&pi->dev, "epia: port 0x%x, mode %d, test=(%d,%d,%d)\n",
		pi->port, pi->mode, e[0], e[1], f);

	return (e[0] && e[1]) || f;
}


static void epia_log_adapter(struct pi_adapter *pi)
{
	char *mode[6] = { "4-bit", "5/3", "8-bit", "EPP-8", "EPP-16", "EPP-32"};

	dev_info(&pi->dev,
		 "Shuttle EPIA at 0x%x, mode %d (%s), delay %d\n",
		 pi->port, pi->mode, mode[pi->mode], pi->delay);
}

static struct pi_protocol epia = {
	.owner		= THIS_MODULE,
	.name		= "epia",
	.max_mode	= 6,
	.epp_first	= 3,
	.default_delay	= 1,
	.max_units	= 1,
	.write_regr	= epia_write_regr,
	.read_regr	= epia_read_regr,
	.write_block	= epia_write_block,
	.read_block	= epia_read_block,
	.connect	= epia_connect,
	.disconnect	= epia_disconnect,
	.test_proto	= epia_test_proto,
	.log_adapter	= epia_log_adapter,
};

MODULE_LICENSE("GPL");
MODULE_AUTHOR("Grant R. Guenther <grant@torque.net>");
MODULE_DESCRIPTION("Shuttle Technologies EPIA parallel port IDE adapter "
		   "protocol driver");
module_pata_parport_driver