# SPDX-License-Identifier: GPL-2.0-only
#
# Light sensors
#
# When adding new entries keep the list in alphabetical order
menu "Light sensors"
config ACPI_ALS
tristate "ACPI Ambient Light Sensor"
depends on ACPI
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
select IIO_KFIFO_BUF
help
Say Y here if you want to build a driver for the ACPI0008
Ambient Light Sensor.
To compile this driver as a module, choose M here: the module will
be called acpi-als.
config ADJD_S311
tristate "ADJD-S311-CR999 digital color sensor"
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
depends on I2C
help
If you say yes here you get support for the Avago ADJD-S311-CR999
digital color light sensor.
This driver can also be built as a module. If so, the module
will be called adjd_s311.
config ADUX1020
tristate "ADUX1020 photometric sensor"
select REGMAP_I2C
depends on I2C
help
Say Y here if you want to build a driver for the Analog Devices
ADUX1020 photometric sensor.
To compile this driver as a module, choose M here: the
module will be called adux1020.
config AL3010
tristate "AL3010 ambient light sensor"
depends on I2C
help
Say Y here if you want to build a driver for the Dyna Image AL3010
ambient light sensor.
To compile this driver as a module, choose M here: the
module will be called al3010.
config AL3320A
tristate "AL3320A ambient light sensor"
depends on I2C
help
Say Y here if you want to build a driver for the Dyna Image AL3320A
ambient light sensor.
To compile this driver as a module, choose M here: the
module will be called al3320a.
config APDS9300
tristate "APDS9300 ambient light sensor"
depends on I2C
help
Say Y here if you want to build a driver for the Avago APDS9300
ambient light sensor.
To compile this driver as a module, choose M here: the
module will be called apds9300.
config APDS9960
tristate "Avago APDS9960 gesture/RGB/ALS/proximity sensor"
select REGMAP_I2C
select IIO_BUFFER
select IIO_KFIFO_BUF
depends on I2C
help
Say Y here to build I2C interface support for the Avago
APDS9960 gesture/RGB/ALS/proximity sensor.
To compile this driver as a module, choose M here: the
module will be called apds9960
config AS73211
tristate "AMS AS73211 XYZ color sensor"
depends on I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
If you say yes here you get support for the AMS AS73211
JENCOLOR(R) Digital XYZ Sensor.
For triggered measurements, you will need an additional trigger driver
like IIO_HRTIMER_TRIGGER or IIO_SYSFS_TRIGGER.
This driver can also be built as a module. If so, the module
will be called as73211.
config BH1750
tristate "ROHM BH1750 ambient light sensor"
depends on I2C
help
Say Y here to build support for the ROHM BH1710, BH1715, BH1721,
BH1750, BH1751 ambient light sensors.
To compile this driver as a module, choose M here: the module will
be called bh1750.
config BH1780
tristate "ROHM BH1780 ambient light sensor"
depends on I2C
help
Say Y here to build support for the ROHM BH1780GLI ambient
light sensor.
To compile this driver as a module, choose M here: the module will
be called bh1780.
config CM32181
depends on I2C
tristate "CM32181 driver"
help
Say Y here if you use cm32181.
This option enables ambient light sensor using
Capella cm32181 device driver.
To compile this driver as a module, choose M here:
the module will be called cm32181.
config CM3232
depends on I2C
tristate "CM3232 ambient light sensor"
help
Say Y here if you use cm3232.
This option enables ambient light sensor using
Capella Microsystems cm3232 device driver.
To compile this driver as a module, choose M here:
the module will be called cm3232.
config CM3323
depends on I2C
tristate "Capella CM3323 color light sensor"
help
Say Y here if you want to build a driver for Capella CM3323
color sensor.
To compile this driver as a module, choose M here: the module will
be called cm3323.
config CM3605
tristate "Capella CM3605 ambient light and proximity sensor"
help
Say Y here if you want to build a driver for Capella CM3605
ambient light and short range proximity sensor.
To compile this driver as a module, choose M here: the module will
be called cm3605.
config CM36651
depends on I2C
tristate "CM36651 driver"
help
Say Y here if you use cm36651.
This option enables proximity & RGB sensor using
Capella cm36651 device driver.
To compile this driver as a module, choose M here:
the module will be called cm36651.
config IIO_CROS_EC_LIGHT_PROX
tristate "ChromeOS EC Light and Proximity Sensors"
depends on IIO_CROS_EC_SENSORS_CORE
help
Say Y here if you use the light and proximity sensors
presented by the ChromeOS EC Sensor hub.
To compile this driver as a module, choose M here:
the module will be called cros_ec_light_prox.
config GP2AP002
tristate "Sharp GP2AP002 Proximity/ALS sensor"
depends on I2C
select REGMAP
help
Say Y here if you have a Sharp GP2AP002 proximity/ALS combo-chip
hooked to an I2C bus.
To compile this driver as a module, choose M here: the
module will be called gp2ap002.
config GP2AP020A00F
tristate "Sharp GP2AP020A00F Proximity/ALS sensor"
depends on I2C
select REGMAP_I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
select IRQ_WORK
help
Say Y here if you have a Sharp GP2AP020A00F proximity/ALS combo-chip
hooked to an I2C bus.
To compile this driver as a module, choose M here: the
module will be called gp2ap020a00f.
config IQS621_ALS
tristate "Azoteq IQS621/622 ambient light sensors"
depends on MFD_IQS62X || COMPILE_TEST
help
Say Y here if you want to build support for the Azoteq IQS621
and IQS622 ambient light sensors.
To compile this driver as a module, choose M here: the module
will be called iqs621-als.
config SENSORS_ISL29018
tristate "Intersil 29018 light and proximity sensor"
depends on I2C
select REGMAP_I2C
default n
help
If you say yes here you get support for ambient light sensing and
proximity infrared sensing from Intersil ISL29018.
This driver will provide the measurements of ambient light intensity
in lux, proximity infrared sensing and normal infrared sensing.
Data from sensor is accessible via sysfs.
config SENSORS_ISL29028
tristate "Intersil ISL29028 Concurrent Light and Proximity Sensor"
depends on I2C
select REGMAP_I2C
help
Provides driver for the Intersil's ISL29028 device.
This driver supports the sysfs interface to get the ALS, IR intensity,
Proximity value via iio. The ISL29028 provides the concurrent sensing
of ambient light and proximity.
config ISL29125
tristate "Intersil ISL29125 digital color light sensor"
depends on I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
Say Y here if you want to build a driver for the Intersil ISL29125
RGB light sensor for I2C.
To compile this driver as a module, choose M here: the module will be
called isl29125.
config HID_SENSOR_ALS
depends on HID_SENSOR_HUB
select IIO_BUFFER
select HID_SENSOR_IIO_COMMON
select HID_SENSOR_IIO_TRIGGER
tristate "HID ALS"
help
Say yes here to build support for the HID SENSOR
Ambient light sensor.
To compile this driver as a module, choose M here: the
module will be called hid-sensor-als.
config HID_SENSOR_PROX
depends on HID_SENSOR_HUB
select IIO_BUFFER
select HID_SENSOR_IIO_COMMON
select HID_SENSOR_IIO_TRIGGER
tristate "HID PROX"
help
Say yes here to build support for the HID SENSOR
Proximity sensor.
To compile this driver as a module, choose M here: the
module will be called hid-sensor-prox.
config JSA1212
tristate "JSA1212 ALS and proximity sensor driver"
depends on I2C
select REGMAP_I2C
help
Say Y here if you want to build a IIO driver for JSA1212
proximity & ALS sensor device.
To compile this driver as a module, choose M here:
the module will be called jsa1212.
config ROHM_BU27008
tristate "ROHM BU27008 color (RGB+C/IR) sensor"
depends on I2C
select REGMAP_I2C
select IIO_GTS_HELPER
help
Enable support for the ROHM BU27008 color sensor.
The ROHM BU27008 is a sensor with 5 photodiodes (red, green,
blue, clear and IR) with four configurable channels. Red and
green being always available and two out of the rest three
(blue, clear, IR) can be selected to be simultaneously measured.
Typical application is adjusting LCD backlight of TVs,
mobile phones and tablet PCs.
config ROHM_BU27034
tristate "ROHM BU27034 ambient light sensor"
depends on I2C
select REGMAP_I2C
select IIO_GTS_HELPER
select IIO_BUFFER
select IIO_KFIFO_BUF
help
Enable support for the ROHM BU27034 ambient light sensor. ROHM BU27034
is an ambient light sesnor with 3 channels and 3 photo diodes capable
of detecting a very wide range of illuminance.
Typical application is adjusting LCD and backlight power of TVs and
mobile phones.
config RPR0521
tristate "ROHM RPR0521 ALS and proximity sensor driver"
depends on I2C
select REGMAP_I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
Say Y here if you want to build support for ROHM's RPR0521
ambient light and proximity sensor device.
To compile this driver as a module, choose M here:
the module will be called rpr0521.
config SENSORS_LM3533
tristate "LM3533 ambient light sensor"
depends on MFD_LM3533
help
If you say yes here you get support for the ambient light sensor
interface on National Semiconductor / TI LM3533 Lighting Power
chips.
The sensor interface can be used to control the LEDs and backlights
of the chip through defining five light zones and three sets of
corresponding output-current values.
The driver provides raw and mean adc readings along with the current
light zone through sysfs. A threshold event can be generated on zone
changes. The ALS-control output values can be set per zone for the
three current output channels.
config LTR501
tristate "LTR-501ALS-01 light sensor"
depends on I2C
select REGMAP_I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
If you say yes here you get support for the Lite-On LTR-501ALS-01
ambient light and proximity sensor. This driver also supports LTR-559
ALS/PS or LTR-301 ALS sensors.
This driver can also be built as a module. If so, the module
will be called ltr501.
config LTRF216A
tristate "Liteon LTRF216A Light Sensor"
depends on I2C
select REGMAP_I2C
help
If you say Y or M here, you get support for Liteon LTRF216A
Ambient Light Sensor.
If built as a dynamically linked module, it will be called
ltrf216a.
config LV0104CS
tristate "LV0104CS Ambient Light Sensor"
depends on I2C
help
Say Y here if you want to build support for the On Semiconductor
LV0104CS ambient light sensor.
To compile this driver as a module, choose M here:
the module will be called lv0104cs.
config MAX44000
tristate "MAX44000 Ambient and Infrared Proximity Sensor"
depends on I2C
select REGMAP_I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
Say Y here if you want to build support for Maxim Integrated's
MAX44000 ambient and infrared proximity sensor device.
To compile this driver as a module, choose M here:
the module will be called max44000.
config MAX44009
tristate "MAX44009 Ambient Light Sensor"
depends on I2C
select REGMAP_I2C
help
Say Y here if you want to build support for Maxim Integrated's
MAX44009 ambient light sensor device.
To compile this driver as a module, choose M here:
the module will be called max44009.
config NOA1305
tristate "ON Semiconductor NOA1305 ambient light sensor"
depends on I2C
select REGMAP_I2C
help
Say Y here if you want to build support for the ON Semiconductor
NOA1305 ambient light sensor.
To compile this driver as a module, choose M here:
The module will be called noa1305.
config OPT3001
tristate "Texas Instruments OPT3001 Light Sensor"
depends on I2C
help
If you say Y or M here, you get support for Texas Instruments
OPT3001 Ambient Light Sensor.
If built as a dynamically linked module, it will be called
opt3001.
config OPT4001
tristate "Texas Instruments OPT4001 Light Sensor"
depends on I2C
select REGMAP_I2C
help
If you say Y or M here, you get support for Texas Instruments
OPT4001 Ambient Light Sensor.
If built as a dynamically linked module, it will be called
opt4001.
config PA12203001
tristate "TXC PA12203001 light and proximity sensor"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for the TXC PA12203001
ambient light and proximity sensor.
This driver can also be built as a module. If so, the module
will be called pa12203001.
config SI1133
tristate "SI1133 UV Index Sensor and Ambient Light Sensor"
depends on I2C
select REGMAP_I2C
help
Say Y here if you want to build a driver for the Silicon Labs SI1133
UV Index Sensor and Ambient Light Sensor chip.
To compile this driver as a module, choose M here: the module will be
called si1133.
config SI1145
tristate "SI1132 and SI1141/2/3/5/6/7 combined ALS, UV index and proximity sensor"
depends on I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
Say Y here if you want to build a driver for the Silicon Labs SI1132 or
SI1141/2/3/5/6/7 combined ambient light, UV index and proximity sensor
chips.
To compile this driver as a module, choose M here: the module will be
called si1145.
config STK3310
tristate "STK3310 ALS and proximity sensor"
depends on I2C
select REGMAP_I2C
help
Say yes here to get support for the Sensortek STK3310 ambient light
and proximity sensor. The STK3311 model is also supported by this
driver.
Choosing M will build the driver as a module. If so, the module
will be called stk3310.
config ST_UVIS25
tristate "STMicroelectronics UVIS25 sensor driver"
depends on (I2C || SPI)
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
select ST_UVIS25_I2C if (I2C)
select ST_UVIS25_SPI if (SPI_MASTER)
help
Say yes here to build support for STMicroelectronics UVIS25
uv sensor
To compile this driver as a module, choose M here: the module
will be called st_uvis25.
config ST_UVIS25_I2C
tristate
depends on ST_UVIS25
select REGMAP_I2C
config ST_UVIS25_SPI
tristate
depends on ST_UVIS25
select REGMAP_SPI
config TCS3414
tristate "TAOS TCS3414 digital color sensor"
depends on I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
If you say yes here you get support for the TAOS TCS3414
family of digital color sensors.
This driver can also be built as a module. If so, the module
will be called tcs3414.
config TCS3472
tristate "TAOS TCS3472 color light-to-digital converter"
depends on I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
If you say yes here you get support for the TAOS TCS3472
family of color light-to-digital converters with IR filter.
This driver can also be built as a module. If so, the module
will be called tcs3472.
config SENSORS_TSL2563
tristate "TAOS TSL2560, TSL2561, TSL2562 and TSL2563 ambient light sensors"
depends on I2C
help
If you say yes here you get support for the Taos TSL2560,
TSL2561, TSL2562 and TSL2563 ambient light sensors.
This driver can also be built as a module. If so, the module
will be called tsl2563.
config TSL2583
tristate "TAOS TSL2580, TSL2581 and TSL2583 light-to-digital converters"
depends on I2C
help
Provides support for the TAOS tsl2580, tsl2581 and tsl2583 devices.
Access ALS data via iio, sysfs.
config TSL2591
tristate "TAOS TSL2591 ambient light sensor"
depends on I2C
help
Select Y here for support of the AMS/TAOS TSL2591 ambient light sensor,
featuring channels for combined visible + IR intensity and lux illuminance.
Access data via iio and sysfs. Supports iio_events.
To compile this driver as a module, select M: the
module will be called tsl2591.
config TSL2772
tristate "TAOS TSL/TMD2x71 and TSL/TMD2x72 Family of light and proximity sensors"
depends on I2C
help
Support for: tsl2571, tsl2671, tmd2671, tsl2771, tmd2771, tsl2572, tsl2672,
tmd2672, tsl2772, tmd2772 devices.
Provides iio_events and direct access via sysfs.
config TSL4531
tristate "TAOS TSL4531 ambient light sensors"
depends on I2C
help
Say Y here if you want to build a driver for the TAOS TSL4531 family
of ambient light sensors with direct lux output.
To compile this driver as a module, choose M here: the
module will be called tsl4531.
config US5182D
tristate "UPISEMI light and proximity sensor"
depends on I2C
help
If you say yes here you get support for the UPISEMI US5182D
ambient light and proximity sensor.
This driver can also be built as a module. If so, the module
will be called us5182d.
config VCNL4000
tristate "VCNL4000/4010/4020/4200 combined ALS and proximity sensor"
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
depends on I2C
help
Say Y here if you want to build a driver for the Vishay VCNL4000,
VCNL4010, VCNL4020, VCNL4200 combined ambient light and proximity
sensor.
To compile this driver as a module, choose M here: the
module will be called vcnl4000.
config VCNL4035
tristate "VCNL4035 combined ALS and proximity sensor"
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
select REGMAP_I2C
depends on I2C
help
Say Y here if you want to build a driver for the Vishay VCNL4035,
combined ambient light (ALS) and proximity sensor. Currently only ALS
function is available.
To compile this driver as a module, choose M here: the
module will be called vcnl4035.
config VEML6030
tristate "VEML6030 ambient light sensor"
select REGMAP_I2C
depends on I2C
help
Say Y here if you want to build a driver for the Vishay VEML6030
ambient light sensor (ALS).
To compile this driver as a module, choose M here: the
module will be called veml6030.
config VEML6070
tristate "VEML6070 UV A light sensor"
depends on I2C
help
Say Y here if you want to build a driver for the Vishay VEML6070 UV A
light sensor.
To compile this driver as a module, choose M here: the
module will be called veml6070.
config VL6180
tristate "VL6180 ALS, range and proximity sensor"
depends on I2C
help
Say Y here if you want to build a driver for the STMicroelectronics
VL6180 combined ambient light, range and proximity sensor.
To compile this driver as a module, choose M here: the
module will be called vl6180.
config ZOPT2201
tristate "ZOPT2201 ALS and UV B sensor"
depends on I2C
help
Say Y here if you want to build a driver for the IDT
ZOPT2201 ambient light and UV B sensor.
To compile this driver as a module, choose M here: the
module will be called zopt2201.
endmenu