// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Driver for MAXI MAX11801 - A Resistive touch screen controller with
 * i2c interface
 *
 * Copyright (C) 2011 Freescale Semiconductor, Inc.
 * Author: Zhang Jiejing <jiejing.zhang@freescale.com>
 *
 * Based on mcs5000_ts.c
 */

/*
 * This driver aims to support the series of MAXI touch chips max11801
 * through max11803. The main difference between these 4 chips can be
 * found in the table below:
 * -----------------------------------------------------
 * | CHIP     |  AUTO MODE SUPPORT(FIFO) | INTERFACE    |
 * |----------------------------------------------------|
 * | max11800 |  YES                     |   SPI        |
 * | max11801 |  YES                     |   I2C        |
 * | max11802 |  NO                      |   SPI        |
 * | max11803 |  NO                      |   I2C        |
 * ------------------------------------------------------
 *
 * Currently, this driver only supports max11801.
 *
 * Data Sheet:
 * http://www.maxim-ic.com/datasheet/index.mvp/id/5943
 */

#include <linux/module.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/input.h>
#include <linux/slab.h>
#include <linux/bitops.h>

/* Register Address define */
#define GENERNAL_STATUS_REG		0x00
#define GENERNAL_CONF_REG		0x01
#define MESURE_RES_CONF_REG		0x02
#define MESURE_AVER_CONF_REG		0x03
#define ADC_SAMPLE_TIME_CONF_REG	0x04
#define PANEL_SETUPTIME_CONF_REG	0x05
#define DELAY_CONVERSION_CONF_REG	0x06
#define TOUCH_DETECT_PULLUP_CONF_REG	0x07
#define AUTO_MODE_TIME_CONF_REG		0x08 /* only for max11800/max11801 */
#define APERTURE_CONF_REG		0x09 /* only for max11800/max11801 */
#define AUX_MESURE_CONF_REG		0x0a
#define OP_MODE_CONF_REG		0x0b

/* FIFO is found only in max11800 and max11801 */
#define FIFO_RD_CMD			(0x50 << 1)
#define MAX11801_FIFO_INT		(1 << 2)
#define MAX11801_FIFO_OVERFLOW		(1 << 3)

#define XY_BUFSIZE			4
#define XY_BUF_OFFSET			4

#define MAX11801_MAX_X			0xfff
#define MAX11801_MAX_Y			0xfff

#define MEASURE_TAG_OFFSET		2
#define MEASURE_TAG_MASK		(3 << MEASURE_TAG_OFFSET)
#define EVENT_TAG_OFFSET		0
#define EVENT_TAG_MASK			(3 << EVENT_TAG_OFFSET)
#define MEASURE_X_TAG			(0 << MEASURE_TAG_OFFSET)
#define MEASURE_Y_TAG			(1 << MEASURE_TAG_OFFSET)

/* These are the state of touch event state machine */
enum {
	EVENT_INIT,
	EVENT_MIDDLE,
	EVENT_RELEASE,
	EVENT_FIFO_END
};

struct max11801_data {
	struct i2c_client		*client;
	struct input_dev		*input_dev;
};

static u8 read_register(struct i2c_client *client, int addr)
{
	/* XXX: The chip ignores LSB of register address */
	return i2c_smbus_read_byte_data(client, addr << 1);
}

static int max11801_write_reg(struct i2c_client *client, int addr, int data)
{
	/* XXX: The chip ignores LSB of register address */
	return i2c_smbus_write_byte_data(client, addr << 1, data);
}

static irqreturn_t max11801_ts_interrupt(int irq, void *dev_id)
{
	struct max11801_data *data = dev_id;
	struct i2c_client *client = data->client;
	int status, i, ret;
	u8 buf[XY_BUFSIZE];
	int x = -1;
	int y = -1;

	status = read_register(data->client, GENERNAL_STATUS_REG);

	if (status & (MAX11801_FIFO_INT | MAX11801_FIFO_OVERFLOW)) {
		status = read_register(data->client, GENERNAL_STATUS_REG);

		ret = i2c_smbus_read_i2c_block_data(client, FIFO_RD_CMD,
						    XY_BUFSIZE, buf);

		/*
		 * We should get 4 bytes buffer that contains X,Y
		 * and event tag
		 */
		if (ret < XY_BUFSIZE)
			goto out;

		for (i = 0; i < XY_BUFSIZE; i += XY_BUFSIZE / 2) {
			if ((buf[i + 1] & MEASURE_TAG_MASK) == MEASURE_X_TAG)
				x = (buf[i] << XY_BUF_OFFSET) +
				    (buf[i + 1] >> XY_BUF_OFFSET);
			else if ((buf[i + 1] & MEASURE_TAG_MASK) == MEASURE_Y_TAG)
				y = (buf[i] << XY_BUF_OFFSET) +
				    (buf[i + 1] >> XY_BUF_OFFSET);
		}

		if ((buf[1] & EVENT_TAG_MASK) != (buf[3] & EVENT_TAG_MASK))
			goto out;

		switch (buf[1] & EVENT_TAG_MASK) {
		case EVENT_INIT:
		case EVENT_MIDDLE:
			input_report_abs(data->input_dev, ABS_X, x);
			input_report_abs(data->input_dev, ABS_Y, y);
			input_event(data->input_dev, EV_KEY, BTN_TOUCH, 1);
			input_sync(data->input_dev);
			break;

		case EVENT_RELEASE:
			input_event(data->input_dev, EV_KEY, BTN_TOUCH, 0);
			input_sync(data->input_dev);
			break;

		case EVENT_FIFO_END:
			break;
		}
	}
out:
	return IRQ_HANDLED;
}

static void max11801_ts_phy_init(struct max11801_data *data)
{
	struct i2c_client *client = data->client;

	/* Average X,Y, take 16 samples, average eight media sample */
	max11801_write_reg(client, MESURE_AVER_CONF_REG, 0xff);
	/* X,Y panel setup time set to 20us */
	max11801_write_reg(client, PANEL_SETUPTIME_CONF_REG, 0x11);
	/* Rough pullup time (2uS), Fine pullup time (10us)  */
	max11801_write_reg(client, TOUCH_DETECT_PULLUP_CONF_REG, 0x10);
	/* Auto mode init period = 5ms , scan period = 5ms*/
	max11801_write_reg(client, AUTO_MODE_TIME_CONF_REG, 0xaa);
	/* Aperture X,Y set to +- 4LSB */
	max11801_write_reg(client, APERTURE_CONF_REG, 0x33);
	/* Enable Power, enable Automode, enable Aperture, enable Average X,Y */
	max11801_write_reg(client, OP_MODE_CONF_REG, 0x36);
}

static int max11801_ts_probe(struct i2c_client *client)
{
	struct max11801_data *data;
	struct input_dev *input_dev;
	int error;

	data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
	input_dev = devm_input_allocate_device(&client->dev);
	if (!data || !input_dev) {
		dev_err(&client->dev, "Failed to allocate memory\n");
		return -ENOMEM;
	}

	data->client = client;
	data->input_dev = input_dev;

	input_dev->name = "max11801_ts";
	input_dev->id.bustype = BUS_I2C;
	input_dev->dev.parent = &client->dev;

	__set_bit(EV_ABS, input_dev->evbit);
	__set_bit(EV_KEY, input_dev->evbit);
	__set_bit(BTN_TOUCH, input_dev->keybit);
	input_set_abs_params(input_dev, ABS_X, 0, MAX11801_MAX_X, 0, 0);
	input_set_abs_params(input_dev, ABS_Y, 0, MAX11801_MAX_Y, 0, 0);

	max11801_ts_phy_init(data);

	error = devm_request_threaded_irq(&client->dev, client->irq, NULL,
					  max11801_ts_interrupt,
					  IRQF_TRIGGER_LOW | IRQF_ONESHOT,
					  "max11801_ts", data);
	if (error) {
		dev_err(&client->dev, "Failed to register interrupt\n");
		return error;
	}

	error = input_register_device(data->input_dev);
	if (error)
		return error;

	return 0;
}

static const struct i2c_device_id max11801_ts_id[] = {
	{"max11801", 0},
	{ }
};
MODULE_DEVICE_TABLE(i2c, max11801_ts_id);

static const struct of_device_id max11801_ts_dt_ids[] = {
	{ .compatible = "maxim,max11801" },
	{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, max11801_ts_dt_ids);

static struct i2c_driver max11801_ts_driver = {
	.driver = {
		.name	= "max11801_ts",
		.of_match_table = max11801_ts_dt_ids,
	},
	.id_table	= max11801_ts_id,
	.probe		= max11801_ts_probe,
};

module_i2c_driver(max11801_ts_driver);

MODULE_AUTHOR("Zhang Jiejing <jiejing.zhang@freescale.com>");
MODULE_DESCRIPTION("Touchscreen driver for MAXI MAX11801 controller");
MODULE_LICENSE("GPL"