#include <linux/platform_device.h>
#include "pinctrl-starfive-jhb100.h"
#define PADNUM_PER2_GPIO_D19 19
#define PADNUM_PER2_GPIO_D20 20
#define PADNUM_PER2_GPIO_D21 21
#define PADNUM_PER2_GPIO_D22 22
#define PADNUM_PER2_GPIO_D23 23
#define PADNUM_PER2_GPIO_D24 24
#define PADNUM_PER2_GPIO_D25 25
#define PADNUM_PER2_GPIO_D26 26
#define PADNUM_PER2_GPIO_D27 27
#define PADNUM_PER2_GPIO_D28 28
#define PADNUM_PER2_GPIO_D29 29
#define PADNUM_PER2_GPIO_D30 30
static const struct jhb100_pin_layout_desc jhb100_per2_pl_desc[] = {
{ .pin_start = 0, .pin_cnt = 15, .name = "gpio", .gpio_func_sel = 0 },
{ .pin_start = 15, .pin_cnt = 1, .name = "gpio", .gpio_func_sel = -1 },
{ .pin_start = 16, .pin_cnt = 15, .name = "gpio", .gpio_func_sel = 0 },
{ 0xff },
};
static const struct config_reg_layout_desc jhb100_per2_pinctrl_rl_desc[] = {
{
.pin_start = 0,
.pin_cnt = 19,
.fields[PAD_CFG_DRIVE_STRENGTH_2BIT] = { .shift = 0, .width = 2 },
.fields[PAD_CFG_INPUT_ENABLE] = { .shift = 2, .width = 1 },
.fields[PAD_CFG_PULL_DOWN] = { .shift = 3, .width = 1 },
.fields[PAD_CFG_PULL_UP] = { .shift = 4, .width = 1 },
.fields[PAD_CFG_SLEW_RATE] = { .shift = 5, .width = 1 },
.fields[PAD_CFG_SCHMITT_TRIGGER_SELECT] = { .shift = 6, .width = 1 },
.fields[PAD_CFG_DEBOUNCE_WIDTH] = { .shift = 15, .width = 17 },
},
{
.pin_start = 19,
.pin_cnt = 12,
.fields[PAD_CFG_INPUT_ENABLE] = { .shift = 0, .width = 1 },
.fields[PAD_CFG_SLEW_RATE] = { .shift = 1, .width = 1 },
.fields[PAD_CFG_VSEL] = { .shift = 2, .width = 2 },
.fields[PAD_CFG_DEBOUNCE_WIDTH] = { .shift = 15, .width = 17 },
},
{ 0xff },
};
static const struct pinvref_desc pinvref_desc_per2[] = {
{
.pin_grp = {
PADNUM_PER2_GPIO_D19,
PADNUM_PER2_GPIO_D20,
PADNUM_PER2_GPIO_D21,
PADNUM_PER2_GPIO_D22,
PADNUM_PER2_GPIO_D23,
PADNUM_PER2_GPIO_D24,
PADNUM_PER2_GPIO_D25,
PADNUM_PER2_GPIO_D26,
PADNUM_PER2_GPIO_D27,
PADNUM_PER2_GPIO_D28,
PADNUM_PER2_GPIO_D29,
PADNUM_PER2_GPIO_D30
},
.num_pins = 12,
.range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_2_5V) |
BIT(JHB100_PINVREF_3_3V)
},
};
static const struct starfive_pinctrl_regs jhb100_per2_pinctrl_regs = {
.vref = { .reg = 0x00, .pv_desc = pinvref_desc_per2,
.num_pv = ARRAY_SIZE(pinvref_desc_per2) },
.func_sel = { .reg = 0x8c, .width_per_pin = 2 },
.config = 0x04,
.output = 0x80,
.output_en = 0x84,
.gpio_status = 0x88,
.irq_en = 0x94,
.irq_status = 0x98,
.irq_clr = 0x9c,
.irq_trigger = 0xa0,
.irq_level = 0xa4,
.irq_both_edge = 0xa8,
.irq_edge = 0xac,
};
static const struct jhb100_pinctrl_func_maps jhb100_func_maps_per2[] = {
{ .func = "fan_tach", .val = 1 },
{ .func = "gmac_rgmii", .val = 1 },
{ .func = "gmac_rmii", .val = 2 },
{ .func = "gpio", .val = 0 },
{ .func = "host0_port80", .val = 2 },
{ .func = "host1_port80", .val = 3 },
};
static const struct jhb100_pinctrl_domain_info jhb100_per2_pinctrl_info = {
.name = "jhb100-per2",
.pl_desc = jhb100_per2_pl_desc,
.crl_desc = jhb100_per2_pinctrl_rl_desc,
.regs = &jhb100_per2_pinctrl_regs,
.fmaps = jhb100_func_maps_per2,
.num_maps = ARRAY_SIZE(jhb100_func_maps_per2),
};
static const struct of_device_id jhb100_per2_pinctrl_of_match[] = {
{
.compatible = "starfive,jhb100-per2-pinctrl",
.data = &jhb100_per2_pinctrl_info,
},
{ }
};
MODULE_DEVICE_TABLE(of, jhb100_per2_pinctrl_of_match);
static struct platform_driver jhb100_per2_pinctrl_driver = {
.probe = jhb100_pinctrl_probe,
.driver = {
.name = "starfive-jhb100-per2-pinctrl",
.of_match_table = jhb100_per2_pinctrl_of_match,
},
};
module_platform_driver(jhb100_per2_pinctrl_driver);
MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC Peripheral-2 domain");
MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
MODULE_LICENSE("GPL"