// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2025, Teguh Sobirin.
 */

#include <dt-bindings/leds/common.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "qcs8550.dtsi"
#include "pm8550.dtsi"
#include "pm8550b.dtsi"
#define PMK8550VE_SID 5
#include "pm8550ve.dtsi"
#include "pm8550vs.dtsi"
#include "pmk8550.dtsi"

/delete-node/ &aop_image_mem;
/delete-node/ &aop_config_mem;
/delete-node/ &camera_mem;
/delete-node/ &ipa;
/delete-node/ &ipa_fw_mem;
/delete-node/ &ipa_gsi_mem;
/delete-node/ &mpss_dsm_mem;
/delete-node/ &mpss_mem;
/delete-node/ &q6_mpss_dtb_mem;
/delete-node/ &remoteproc_mpss;

/ {
	chassis-type = "handset";

	aliases {
		serial0 = &uart7;
		serial1 = &uart14;
	};

	/* The tzlog label is required by ABL to apply a dtbo, but it can be on any node */
	qcom_tzlog: chosen {
		stdout-path = "serial0:115200n8";
	};

	gpio_keys: gpio-keys {
		compatible = "gpio-keys";

		pinctrl-0 = <&volume_up_n>;
		pinctrl-names = "default";

		key-volume-up {
			label = "Volume Up";
			debounce-interval = <15>;
			gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
			linux,code = <KEY_VOLUMEUP>;
			linux,can-disable;
			wakeup-source;
		};
	};

	pmic-glink {
		compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
		#address-cells = <1>;
		#size-cells = <0>;
		orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;

		connector@0 {
			compatible = "usb-c-connector";
			reg = <0>;
			power-role = "dual";
			data-role = "dual";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;

					pmic_glink_hs_in: endpoint {
						remote-endpoint = <&usb_1_dwc3_hs>;
					};
				};

				port@1 {
					reg = <1>;

					pmic_glink_ss_in: endpoint {
						remote-endpoint = <&usb_dp_qmpphy_out>;
					};
				};

				port@2 {
					reg = <2>;

					pmic_glink_sbu: endpoint {
						remote-endpoint = <&usb0_sbu_mux>;
					};
				};
			};
		};
	};

	pwm_fan: pwm-fan {
		compatible = "pwm-fan";

		fan-supply = <&vdd_fan_5v0>;
		pwms = <&pm8550_pwm 3 50000>;

		pinctrl-0 = <&fan_pwm_active>, <&fan_int>;
		pinctrl-names = "default";

		pulses-per-revolution = <4>;
		interrupts-extended = <&tlmm 13 IRQ_TYPE_EDGE_FALLING>;

		cooling-levels = <0 40 65 75 90 100 120 150 175>;
		#cooling-cells = <2>;
	};

	reserved-memory {
		hyp_mem: hyp-region@80000000 {
			reg = <0 0x80000000 0 0xa00000>;
			no-map;
		};

		cpusys_vm_mem: cpusys-vm-region@80a00000 {
			reg = <0 0x80a00000 0 0x400000>;
			no-map;
		};

		hyp_tags_mem: hyp-tags-region@80e00000 {
			reg = <0 0x80e00000 0 0x3d0000>;
			no-map;
		};

		xbl_sc_mem: xbl-sc-region@d8100000 {
			reg = <0 0xd8100000 0 0x40000>;
			no-map;
		};

		hyp_tags_reserved_mem: hyp-tags-reserved-region@811d0000 {
			reg = <0 0x811d0000 0 0x30000>;
			no-map;
		};

		xbl_dt_log_merged_mem: xbl-dt-log-merged-region@81a00000 {
			reg = <0 0x81a00000 0 0x260000>;
			no-map;
		};

		aop_config_merged_mem: aop-config-merged-region@81c80000 {
			reg = <0 0x81c80000 0 0x74000>;
			no-map;
		};

		chipinfo_mem: chipinfo-region@81cf4000 {
			reg = <0 0x81cf4000 0 0x1000>;
			no-map;
		};

		global_sync_mem: global-sync-region@82600000 {
			reg = <0 0x82600000 0 0x100000>;
			no-map;
		};

		tz_stat_mem: tz-stat-region@82700000 {
			reg = <0 0x82700000 0 0x100000>;
			no-map;
		};

		cpucp_fw_mem: cpucp-fw-region@d8140000 {
			reg = <0 0xd8140000 0 0x1c0000>;
			no-map;
		};

		qtee_mem: qtee-region@d8300000 {
			reg = <0 0xd8300000 0 0x500000>;
			no-map;
		};

		hwfence_shbuf: hwfence-shbuf-region@e6440000 {
			reg = <0 0xe6440000 0 0x2dd000>;
			no-map;
		};

		hyp_ext_reserved_mem: hyp-ext-reserved-region@ff700000 {
			reg = <0 0xff700000 0 0x100000>;
			no-map;
		};

		llcc_lpi_mem: llcc_lpi_region@ff800000 {
			reg = <0 0xff800000 0 0x600000>;
			no-map;
		};

		hyp_ext_tags_mem: hyp-ext-tags-region@fce00000 {
			reg = <0 0xfce00000 0 0x2900000>;
			no-map;
		};
	};

	sound {
		compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
		pinctrl-0 = <&i2s0_default_state>, <&audio_mclk0_default_state>, <&lpi_i2s3_active>;
		pinctrl-names = "default";

		model = "AYN-Odin2";
		audio-routing = "IN1_HPHL", "HPHL_OUT",
				"IN2_HPHR", "HPHR_OUT",
				"AMIC2", "MIC BIAS2",
				"TX SWR_INPUT1", "ADC2_OUTPUT";

		speaker-i2s-dai-link {
			link-name = "Primary MI2S Playback";

			codec {
				sound-dai = <&spk_amp_l>, <&spk_amp_r>;
			};

			cpu {
				sound-dai = <&q6apmbedai PRIMARY_MI2S_RX>;
			};

			platform {
				sound-dai = <&q6apm>;
			};
		};

		wcd-playback-dai-link {
			link-name = "WCD Playback";

			codec {
				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
			};

			cpu {
				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
			};

			platform {
				sound-dai = <&q6apm>;
			};
		};

		wcd-capture-dai-link {
			link-name = "WCD Capture";

			codec {
				sound-dai = <&wcd938x 1>, <&swr2 0>, <&lpass_txmacro 0>;
			};

			cpu {
				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
			};

			platform {
				sound-dai = <&q6apm>;
			};
		};

		dp0-dai-link {
			link-name = "DP0 Playback";

			codec {
				sound-dai = <&mdss_dp0>;
			};

			cpu {
				sound-dai = <&q6apmbedai DISPLAY_PORT_RX_0>;
			};

			platform {
				sound-dai = <&q6apm>;
			};
		};
	};

	thermal-zones {
		cpu0-thermal {
			polling-delay = <200>;

			trips {
				cpuss0_active0: cpu-active0 {
					temperature = <50000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss0_active1: cpu-active1 {
					temperature = <55000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss0_active2: cpu-active2 {
					temperature = <60000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss0_active3: cpu-active3 {
					temperature = <65000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss0_active4: cpu-active4 {
					temperature = <70000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss0_active5: cpu-active5 {
					temperature = <75000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss0_active6: cpu-active6 {
					temperature = <80000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss0_active7: cpu-active7 {
					temperature = <85000>;
					hysteresis = <4000>;
					type = "active";
				};
			};

			cooling-maps {
				map0 {
					cooling-device = <&pwm_fan 0 1>;
					trip = <&cpuss0_active0>;
				};

				map1 {
					cooling-device = <&pwm_fan 1 2>;
					trip = <&cpuss0_active1>;
				};

				map2 {
					cooling-device = <&pwm_fan 2 3>;
					trip = <&cpuss0_active2>;
				};

				map3 {
					cooling-device = <&pwm_fan 3 4>;
					trip = <&cpuss0_active3>;
				};

				map4 {
					cooling-device = <&pwm_fan 4 5>;
					trip = <&cpuss0_active4>;
				};

				map5 {
					cooling-device = <&pwm_fan 5 6>;
					trip = <&cpuss0_active5>;
				};

				map6 {
					cooling-device = <&pwm_fan 6 7>;
					trip = <&cpuss0_active6>;
				};

				map7 {
					cooling-device = <&pwm_fan 7 8>;
					trip = <&cpuss0_active7>;
				};
			};
		};

		cpu3-bottom-thermal {
			polling-delay = <200>;

			trips {
				cpuss3_active0: cpu-active0 {
					temperature = <50000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss3_active1: cpu-active1 {
					temperature = <55000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss3_active2: cpu-active2 {
					temperature = <60000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss3_active3: cpu-active3 {
					temperature = <65000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss3_active4: cpu-active4 {
					temperature = <70000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss3_active5: cpu-active5 {
					temperature = <75000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss3_active6: cpu-active6 {
					temperature = <80000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss3_active7: cpu-active7 {
					temperature = <85000>;
					hysteresis = <4000>;
					type = "active";
				};
			};

			cooling-maps {
				map0 {
					cooling-device = <&pwm_fan 0 1>;
					trip = <&cpuss3_active0>;
				};

				map1 {
					cooling-device = <&pwm_fan 1 2>;
					trip = <&cpuss3_active1>;
				};

				map2 {
					cooling-device = <&pwm_fan 2 3>;
					trip = <&cpuss3_active2>;
				};

				map3 {
					cooling-device = <&pwm_fan 3 4>;
					trip = <&cpuss3_active3>;
				};

				map4 {
					cooling-device = <&pwm_fan 4 5>;
					trip = <&cpuss3_active4>;
				};

				map5 {
					cooling-device = <&pwm_fan 5 6>;
					trip = <&cpuss3_active5>;
				};

				map6 {
					cooling-device = <&pwm_fan 6 7>;
					trip = <&cpuss3_active6>;
				};

				map7 {
					cooling-device = <&pwm_fan 7 8>;
					trip = <&cpuss3_active7>;
				};
			};
		};

		cpu7-bottom-thermal {
			polling-delay = <200>;

			trips {
				cpuss7_active0: cpu-active0 {
					temperature = <50000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss7_active1: cpu-active1 {
					temperature = <55000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss7_active2: cpu-active2 {
					temperature = <60000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss7_active3: cpu-active3 {
					temperature = <65000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss7_active4: cpu-active4 {
					temperature = <70000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss7_active5: cpu-active5 {
					temperature = <75000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss7_active6: cpu-active6 {
					temperature = <80000>;
					hysteresis = <4000>;
					type = "active";
				};

				cpuss7_active7: cpu-active7 {
					temperature = <85000>;
					hysteresis = <4000>;
					type = "active";
				};
			};

			cooling-maps {
				map0 {
					cooling-device = <&pwm_fan 0 1>;
					trip = <&cpuss7_active0>;
				};

				map1 {
					cooling-device = <&pwm_fan 1 2>;
					trip = <&cpuss7_active1>;
				};

				map2 {
					cooling-device = <&pwm_fan 2 3>;
					trip = <&cpuss7_active2>;
				};

				map3 {
					cooling-device = <&pwm_fan 3 4>;
					trip = <&cpuss7_active3>;
				};

				map4 {
					cooling-device = <&pwm_fan 4 5>;
					trip = <&cpuss7_active4>;
				};

				map5 {
					cooling-device = <&pwm_fan 5 6>;
					trip = <&cpuss7_active5>;
				};

				map6 {
					cooling-device = <&pwm_fan 6 7>;
					trip = <&cpuss7_active6>;
				};

				map7 {
					cooling-device = <&pwm_fan 7 8>;
					trip = <&cpuss7_active7>;
				};
			};
		};

		gpuss-0-thermal {
			polling-delay = <200>;

			trips {
				gpuss0_active0: gpu-active0 {
					temperature = <50000>;
					hysteresis = <4000>;
					type = "active";
				};

				gpuss0_active1: gpu-active1 {
					temperature = <55000>;
					hysteresis = <4000>;
					type = "active";
				};

				gpuss0_active2: gpu-active2 {
					temperature = <60000>;
					hysteresis = <4000>;
					type = "active";
				};

				gpuss0_active3: gpu-active3 {
					temperature = <65000>;
					hysteresis = <4000>;
					type = "active";
				};

				gpuss0_active4: gpu-active4 {
					temperature = <70000>;
					hysteresis = <4000>;
					type = "active";
				};

				gpuss0_active5: gpu-active5 {
					temperature = <75000>;
					hysteresis = <4000>;
					type = "active";
				};

				gpuss0_active6: gpu-active6 {
					temperature = <80000>;
					hysteresis = <4000>;
					type = "active";
				};

				gpuss0_active7: gpu-active7 {
					temperature = <85000>;
					hysteresis = <4000>;
					type = "active";
				};
			};

			cooling-maps {
				map0 {
					cooling-device = <&pwm_fan 0 1>;
					trip = <&gpuss0_active0>;
				};

				map1 {
					cooling-device = <&pwm_fan 1 2>;
					trip = <&gpuss0_active1>;
				};

				map2 {
					cooling-device = <&pwm_fan 2 3>;
					trip = <&gpuss0_active2>;
				};

				map3 {
					cooling-device = <&pwm_fan 3 4>;
					trip = <&gpuss0_active3>;
				};

				map4 {
					cooling-device = <&pwm_fan 4 5>;
					trip = <&gpuss0_active4>;
				};

				map5 {
					cooling-device = <&pwm_fan 5 6>;
					trip = <&gpuss0_active5>;
				};

				map6 {
					cooling-device = <&pwm_fan 6 7>;
					trip = <&gpuss0_active6>;
				};

				map7 {
					cooling-device = <&pwm_fan 7 8>;
					trip = <&gpuss0_active7>;
				};
			};
		};
	};

	usb0-sbu-mux {
		compatible = "pericom,pi3usb102", "gpio-sbu-mux";

		enable-gpios = <&tlmm 140 GPIO_ACTIVE_LOW>;
		select-gpios = <&tlmm 141 GPIO_ACTIVE_HIGH>;

		pinctrl-0 = <&usb0_sbu_default>;
		pinctrl-names = "default";

		mode-switch;
		orientation-switch;

		port {
			usb0_sbu_mux: endpoint {
				remote-endpoint = <&pmic_glink_sbu>;
			};
		};
	};

	vdd_fan_5v0: vdd-fan-5v0-regulator {
		compatible = "regulator-fixed";
		regulator-name = "vdd_fan_5v0";

		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;

		gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
		enable-active-high;

		pinctrl-0 = <&fan_pwr_active>;
		pinctrl-names = "default";

		regulator-state-mem {
			regulator-off-in-suspend;
		};
	};

	vdd_mcu_3v3: vdd-mcu-3v3-regulator {
		compatible = "regulator-fixed";
		regulator-name = "vdd_mcu_3v3";

		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;

		gpio = <&tlmm 99 GPIO_ACTIVE_HIGH>;
		regulator-always-on;
		regulator-boot-on;
		enable-active-high;
	};

	vph_pwr: regulator-vph-pwr {
		compatible = "regulator-fixed";
		regulator-name = "vph_pwr";
		regulator-min-microvolt = <3700000>;
		regulator-max-microvolt = <3700000>;

		regulator-always-on;
		regulator-boot-on;
	};

	wcd938x: audio-codec {
		compatible = "qcom,wcd9385-codec";

		pinctrl-0 = <&wcd_default>;
		pinctrl-names = "default";

		qcom,micbias1-microvolt = <1800000>;
		qcom,micbias2-microvolt = <1800000>;
		qcom,micbias3-microvolt = <1800000>;
		qcom,micbias4-microvolt = <1800000>;
		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000
							 500000 500000 500000 500000>;
		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
		qcom,rx-device = <&wcd_rx>;
		qcom,tx-device = <&wcd_tx>;

		reset-gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;

		vdd-buck-supply = <&vreg_l15b_1p8>;
		vdd-rxtx-supply = <&vreg_l15b_1p8>;
		vdd-io-supply = <&vreg_l15b_1p8>;
		vdd-mic-bias-supply = <&vreg_bob1>;

		#sound-dai-cells = <1>;
	};

	wcn7850-pmu {
		compatible = "qcom,wcn7850-pmu";

		pinctrl-0 = <&wlan_en>, <&bt_default>, <&pmk8550_sleep_clk>;
		pinctrl-names = "default";

		wlan-enable-gpios = <&tlmm 80 GPIO_ACTIVE_HIGH>;
		bt-enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;

		vdd-supply = <&vreg_s5g_0p8>;
		vddio-supply = <&vreg_l15b_1p8>;
		vddaon-supply = <&vreg_s2g_0p8>;
		vdddig-supply = <&vreg_s4e_0p95>;
		vddrfa1p2-supply = <&vreg_s4g_1p3>;
		vddrfa1p8-supply = <&vreg_s6g_1p8>;

		regulators {
			vreg_pmu_rfa_cmn: ldo0 {
				regulator-name = "vreg_pmu_rfa_cmn";
			};

			vreg_pmu_aon_0p59: ldo1 {
				regulator-name = "vreg_pmu_aon_0p59";
			};

			vreg_pmu_wlcx_0p8: ldo2 {
				regulator-name = "vreg_pmu_wlcx_0p8";
			};

			vreg_pmu_wlmx_0p85: ldo3 {
				regulator-name = "vreg_pmu_wlmx_0p85";
			};

			vreg_pmu_btcmx_0p85: ldo4 {
				regulator-name = "vreg_pmu_btcmx_0p85";
			};

			vreg_pmu_rfa_0p8: ldo5 {
				regulator-name = "vreg_pmu_rfa_0p8";
			};

			vreg_pmu_rfa_1p2: ldo6 {
				regulator-name = "vreg_pmu_rfa_1p2";
			};

			vreg_pmu_rfa_1p8: ldo7 {
				regulator-name = "vreg_pmu_rfa_1p8";
			};

			vreg_pmu_pcie_0p9: ldo8 {
				regulator-name = "vreg_pmu_pcie_0p9";
			};

			vreg_pmu_pcie_1p8: ldo9 {
				regulator-name = "vreg_pmu_pcie_1p8";
			};
		};
	};

	/* The arch_timer label is unused here, but is required by ABL to apply a dtbo */
	arch_timer: timer { };
};

&apps_rsc {
	regulators-0 {
		compatible = "qcom,pm8550-rpmh-regulators";
		qcom,pmic-id = "b";

		vdd-bob1-supply = <&vph_pwr>;
		vdd-bob2-supply = <&vph_pwr>;
		vdd-l1-l4-l10-supply = <&vreg_s6g_1p8>;
		vdd-l2-l13-l14-supply = <&vreg_bob1>;
		vdd-l3-supply = <&vreg_s4g_1p3>;
		vdd-l5-l16-supply = <&vreg_bob1>;
		vdd-l6-l7-supply = <&vreg_bob1>;
		vdd-l8-l9-supply = <&vreg_bob1>;
		vdd-l11-supply = <&vreg_s4g_1p3>;
		vdd-l12-supply = <&vreg_s6g_1p8>;
		vdd-l15-supply = <&vreg_s6g_1p8>;
		vdd-l17-supply = <&vreg_bob2>;

		vreg_bob1: bob1 {
			regulator-name = "vreg_bob1";
			regulator-min-microvolt = <3296000>;
			regulator-max-microvolt = <3960000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_bob2: bob2 {
			regulator-name = "vreg_bob2";
			regulator-min-microvolt = <2720000>;
			regulator-max-microvolt = <3960000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l2b_3p0: ldo2 {
			regulator-name = "vreg_l2b_3p0";
			regulator-min-microvolt = <3008000>;
			regulator-max-microvolt = <3008000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l5b_3p1: ldo5 {
			regulator-name = "vreg_l5b_3p1";
			regulator-min-microvolt = <3104000>;
			regulator-max-microvolt = <3104000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l6b_1p8: ldo6 {
			regulator-name = "vreg_l6b_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <3008000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l7b_1p8: ldo7 {
			regulator-name = "vreg_l7b_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <3008000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l8b_1p8: ldo8 {
			regulator-name = "vreg_l8b_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <3008000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l9b_2p9: ldo9 {
			regulator-name = "vreg_l9b_2p9";
			regulator-min-microvolt = <2960000>;
			regulator-max-microvolt = <3008000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l11b_1p2: ldo11 {
			regulator-name = "vreg_l11b_1p2";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1504000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l12b_1p8: ldo12 {
			regulator-name = "vreg_l12b_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l13b_3p0: ldo13 {
			regulator-name = "vreg_l13b_3p0";
			regulator-min-microvolt = <3000000>;
			regulator-max-microvolt = <3000000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l14b_3p2: ldo14 {
			regulator-name = "vreg_l14b_3p2";
			regulator-min-microvolt = <3200000>;
			regulator-max-microvolt = <3200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l15b_1p8: ldo15 {
			regulator-name = "vreg_l15b_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l16b_2p8: ldo16 {
			regulator-name = "vreg_l16b_2p8";
			regulator-min-microvolt = <2800000>;
			regulator-max-microvolt = <2800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l17b_2p5: ldo17 {
			regulator-name = "vreg_l17b_2p5";
			regulator-min-microvolt = <2504000>;
			regulator-max-microvolt = <2504000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};
	};

	regulators-1 {
		compatible = "qcom,pm8550vs-rpmh-regulators";
		qcom,pmic-id = "c";

		vdd-l1-supply = <&vreg_s4g_1p3>;
		vdd-l2-supply = <&vreg_s4e_0p95>;
		vdd-l3-supply = <&vreg_s4e_0p95>;

		vreg_l3c_0p9: ldo3 {
			regulator-name = "vreg_l3c_0p9";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <912000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};
	};

	regulators-2 {
		compatible = "qcom,pm8550vs-rpmh-regulators";
		qcom,pmic-id = "d";

		vdd-l1-supply = <&vreg_s4e_0p95>;
		vdd-l2-supply = <&vreg_s4e_0p95>;
		vdd-l3-supply = <&vreg_s4e_0p95>;

		vreg_l1d_0p88: ldo1 {
			regulator-name = "vreg_l1d_0p88";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <920000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};
	};

	regulators-3 {
		compatible = "qcom,pm8550vs-rpmh-regulators";
		qcom,pmic-id = "e";

		vdd-l1-supply = <&vreg_s4e_0p95>;
		vdd-l2-supply = <&vreg_s4e_0p95>;
		vdd-l3-supply = <&vreg_s4g_1p3>;
		vdd-s4-supply = <&vph_pwr>;
		vdd-s5-supply = <&vph_pwr>;

		vreg_s4e_0p95: smps4 {
			regulator-name = "vreg_s4e_0p95";
			regulator-min-microvolt = <904000>;
			regulator-max-microvolt = <984000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_s5e_1p08: smps5 {
			regulator-name = "vreg_s5e_1p08";
			regulator-min-microvolt = <1010000>;
			regulator-max-microvolt = <1120000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l1e_0p88: ldo1 {
			regulator-name = "vreg_l1e_0p88";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <912000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l2e_0p9: ldo2 {
			regulator-name = "vreg_l2e_0p9";
			regulator-min-microvolt = <870000>;
			regulator-max-microvolt = <970000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l3e_1p2: ldo3 {
			regulator-name = "vreg_l3e_1p2";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};
	};

	regulators-4 {
		compatible = "qcom,pm8550ve-rpmh-regulators";
		qcom,pmic-id = "f";

		vdd-l1-supply = <&vreg_s4e_0p95>;
		vdd-l2-supply = <&vreg_s4e_0p95>;
		vdd-l3-supply = <&vreg_s4e_0p95>;
		vdd-s4-supply = <&vph_pwr>;

		vreg_s4f_0p5: smps4 {
			regulator-name = "vreg_s4f_0p5";
			regulator-min-microvolt = <300000>;
			regulator-max-microvolt = <700000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l1f_0p9: ldo1 {
			regulator-name = "vreg_l1f_0p9";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <912000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l2f_0p88: ldo2 {
			regulator-name = "vreg_l2f_0p88";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <912000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l3f_0p88: ldo3 {
			regulator-name = "vreg_l3f_0p88";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <912000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};
	};

	regulators-5 {
		compatible = "qcom,pm8550vs-rpmh-regulators";
		qcom,pmic-id = "g";

		vdd-l1-supply = <&vreg_s4g_1p3>;
		vdd-l2-supply = <&vreg_s4g_1p3>;
		vdd-l3-supply = <&vreg_s4g_1p3>;
		vdd-s1-supply = <&vph_pwr>;
		vdd-s2-supply = <&vph_pwr>;
		vdd-s3-supply = <&vph_pwr>;
		vdd-s4-supply = <&vph_pwr>;
		vdd-s5-supply = <&vph_pwr>;
		vdd-s6-supply = <&vph_pwr>;

		vreg_s1g_1p2: smps1 {
			regulator-name = "vreg_s1g_1p2";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1300000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_s2g_0p8: smps2 {
			regulator-name = "vreg_s2g_0p8";
			regulator-min-microvolt = <800000>;
			regulator-max-microvolt = <1000000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_s3g_0p7: smps3 {
			regulator-name = "vreg_s3g_0p7";
			regulator-min-microvolt = <300000>;
			regulator-max-microvolt = <1004000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_s4g_1p3: smps4 {
			regulator-name = "vreg_s4g_1p3";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1352000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_s5g_0p8: smps5 {
			regulator-name = "vreg_s5g_0p8";
			regulator-min-microvolt = <500000>;
			regulator-max-microvolt = <1004000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_s6g_1p8: smps6 {
			regulator-name = "vreg_s6g_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <2000000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l1g_1p2: ldo1 {
			regulator-name = "vreg_l1g_1p2";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l3g_1p2: ldo3 {
			regulator-name = "vreg_l3g_1p2";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};
	};
};

&gpi_dma1 {
	status = "okay";
};

&gpi_dma2 {
	status = "okay";
};

&gpu {
	status = "okay";
};

&gpu_zap_shader {
	firmware-name = "qcom/sm8550/a740_zap.mbn";
};

&i2c_master_hub_0 {
	status = "okay";
};

&i2c_hub_2 {
	clock-frequency = <400000>;

	status = "okay";

	spk_amp_l: amplifier@34 {
		compatible = "awinic,aw88166";
		reg = <0x34>;
		reset-gpios = <&tlmm 103 GPIO_ACTIVE_LOW>;
		sound-name-prefix = "Amplifier L";

		awinic,audio-channel = <0>;
		awinic,sync-flag;

		#sound-dai-cells = <0>;
	};

	spk_amp_r: amplifier@35 {
		compatible = "awinic,aw88166";
		reg = <0x35>;
		reset-gpios = <&tlmm 100 GPIO_ACTIVE_LOW>;
		sound-name-prefix = "Amplifier R";

		awinic,audio-channel = <1>;
		awinic,sync-flag;

		#sound-dai-cells = <0>;
	};
};

&iris {
	status = "okay";
};

&lpass_tlmm {
	lpi_i2s3_active: lpi_i2s3-active-state {
		sck-pins {
			pins = "gpio12";
			function = "i2s3_clk";
			drive-strength = <8>;
			bias-disable;
			output-high;
		};

		ws-pins {
			pins = "gpio13";
			function = "i2s3_ws";
			drive-strength = <8>;
			bias-disable;
			output-high;
		};

		data0-pins {
			pins = "gpio17";
			function = "i2s3_data";
			drive-strength = <8>;
			bias-disable;
			output-high;
		};

		data1-pins {
			pins = "gpio18";
			function = "i2s3_data";
			drive-strength = <8>;
			bias-disable;
			output-high;
		};
	};
};

&lpass_vamacro {
	qcom,dmic-sample-rate = <4800000>;
};

&lpass_wsamacro {
	status = "disabled";
};

&mdss {
	status = "okay";
};

&mdss_dp0 {
	status = "okay";
};

&mdss_dsi1 {
	vdda-supply = <&vreg_l3e_1p2>;

	status = "okay";

	display_panel: panel@0 {
		reg = <0>;

		port {
			panel1_in: endpoint {
				remote-endpoint = <&mdss_dsi1_out>;
			};
		};
	};
};

&mdss_dsi1_out {
	remote-endpoint = <&panel1_in>;
	data-lanes = <0 1 2 3>;
};

&mdss_dsi1_phy {
	vdds-supply = <&vreg_l1e_0p88>;

	status = "okay";
};

&pcie0 {
	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;

	pinctrl-0 = <&pcie0_default_state>;
	pinctrl-names = "default";

	status = "okay";
};

&pcie0_port0 {
	wifi@0 {
		compatible = "pci17cb,1107";
		reg = <0x10000 0x0 0x0 0x0 0x0>;

		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
		vddaon-supply = <&vreg_pmu_aon_0p59>;
		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
	};
};

&pcie0_phy {
	vdda-phy-supply = <&vreg_l1e_0p88>;
	vdda-pll-supply = <&vreg_l3e_1p2>;

	status = "okay";
};

&pm8550_gpios {
	fan_pwm_active: fan-pwm-active-state {
		pins = "gpio8";
		function = "func1";
		input-disable;
		output-enable;
		output-low;
		bias-disable;
		power-source = <1>;
	};

	sdc2_card_det_n: sdc2-card-det-n-state {
		pins = "gpio12";
		function = "normal";
		input-enable;
		output-disable;
		bias-pull-up;
		power-source = <1>;
	};

	volume_up_n: volume-up-n-state {
		pins = "gpio6";
		function = "normal";
		power-source = <1>;
		bias-pull-up;
		input-enable;
	};
};

&pm8550_pwm {
	status = "okay";

	pm8550_multi_led: multi-led {
		color = <LED_COLOR_ID_RGB>;
		function = LED_FUNCTION_STATUS;

		#address-cells = <1>;
		#size-cells = <0>;

		led@1 {
			reg = <1>;
			color = <LED_COLOR_ID_RED>;
		};

		led@2 {
			reg = <2>;
			color = <LED_COLOR_ID_GREEN>;
		};

		led@3 {
			reg = <3>;
			color = <LED_COLOR_ID_BLUE>;
		};
	};
};

&pm8550b_eusb2_repeater {
	qcom,tune-usb2-disc-thres = /bits/ 8 <0x6>;
	qcom,tune-usb2-amplitude = /bits/ 8 <0xb>;
	qcom,tune-usb2-preem = /bits/ 8 <0x3>;
	vdd18-supply = <&vreg_l15b_1p8>;
	vdd3-supply = <&vreg_l5b_3p1>;
};

&pmk8550_gpios {
	pmk8550_sleep_clk: sleep-clk-state {
		pins = "gpio3";
		function = "func1";
		input-disable;
		output-enable;
		bias-disable;
		power-source = <0>;
	};

	pwm_backlight_default: pwm-backlight-default-state {
		pins = "gpio5";
		function = "func3";
		input-disable;
		output-low;
		output-enable;
		bias-disable;
		power-source = <0>;
		qcom,drive-strength = <2>;
	};
};

&pmk8550_rtc {
	nvmem-cells = <&rtc_offset>;
	nvmem-cell-names = "offset";
};

&pmk8550_sdam_2 {
	rtc_offset: rtc-offset@bc {
		reg = <0xbc 0x4>;
	};
};

&pon_pwrkey {
	status = "okay";
};

&pon_resin {
	linux,code = <KEY_VOLUMEDOWN>;

	status = "okay";
};

&q6apmbedai {
	#address-cells = <1>;
	#size-cells = <0>;

	dai@16 {
		reg = <PRIMARY_MI2S_RX>;
		clocks = <&q6prmcc LPASS_CLK_ID_PRI_MI2S_IBIT
				   LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
			 <&q6prmcc LPASS_CLK_ID_MCLK_1
				   LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
		clock-names = "bclk", "mclk";
	};
};

&qupv3_id_0 {
	status = "okay";
};

&qupv3_id_1 {
	status = "okay";
};

&remoteproc_cdsp {
	firmware-name = "qcom/sm8550/ayntec/cdsp.mbn",
			"qcom/sm8550/ayntec/cdsp_dtb.mbn";

	status = "okay";
};

&sdhc_2 {
	cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
	pinctrl-names = "default", "sleep";
	vmmc-supply = <&vreg_l9b_2p9>;
	vqmmc-supply = <&vreg_l8b_1p8>;
	no-sdio;
	no-mmc;

	status = "okay";
};

&sleep_clk {
	clock-frequency = <32764>;
};

&swr1 {
	status = "okay";

	wcd_rx: codec@0,4 {
		compatible = "sdw20217010d00";
		reg = <0 4>;
		qcom,rx-port-mapping = <1 2 3 4 5>;
	};
};

&swr2 {
	status = "okay";

	wcd_tx: codec@0,3 {
		compatible = "sdw20217010d00";
		reg = <0 3>;
		qcom,tx-port-mapping = <2 2 3 4>;
	};
};

&tlmm {
	gpio-reserved-ranges = <32 8>;

	mcu_en_active: mcu-en-active-state {
		pins = "gpio12";
		function = "gpio";
		bias-pull-down;
	};

	fan_int: fan-int-state {
		pins = "gpio13";
		function = "gpio";
		drive-strength = <2>;
		bias-disable;
	};

	ts_s_rst_default: ts-s-rst-default-state {
		pins = "gpio14";
		function = "gpio";
		bias-pull-up;
		drive-strength = <8>;
	};

	ts_s_rst_sleep: ts-s-rst-sleep-state {
		pins = "gpio14";
		function = "gpio";
		bias-pull-down;
		drive-strength = <2>;
	};

	ts_s_int_default: ts-s-int-default-state {
		pins = "gpio15";
		function = "gpio";
		bias-pull-up;
		drive-strength = <8>;
	};

	ts_s_int_sleep: ts-s-int-sleep-state {
		pins = "gpio15";
		function = "gpio";
		bias-pull-down;
		drive-strength = <2>;
	};

	ts_p_rst_default: ts-p-rst-default-state {
		pins = "gpio24";
		function = "gpio";
		bias-pull-up;
		drive-strength = <8>;
	};

	ts_p_rst_sleep: ts-p-rst-sleep-state {
		pins = "gpio24";
		function = "gpio";
		bias-pull-down;
		drive-strength = <2>;
	};

	ts_p_int_default: ts-p-int-default-state {
		pins = "gpio25";
		function = "gpio";
		bias-pull-up;
		drive-strength = <8>;
	};

	ts_p_int_sleep: ts-p-int-sleep-state {
		pins = "gpio25";
		function = "gpio";
		bias-pull-down;
		drive-strength = <2>;
	};

	wlan_en: wlan-en-state {
		pins = "gpio80";
		function = "gpio";
		drive-strength = <8>;
		bias-pull-down;
	};

	bt_default: bt-default-state {
		bt-en-pins {
			pins = "gpio81";
			function = "gpio";
			drive-strength = <16>;
			bias-disable;
		};

		sw-ctrl-pins {
			pins = "gpio82";
			function = "gpio";
			bias-pull-down;
		};
	};

	dsi_p_te_active: dsi-p-te-active-state {
		pins = "gpio86";
		function = "mdp_vsync";
		drive-strength = <2>;
		bias-pull-down;
	};

	dsi_p_te_suspend: dsi-s-te-suspend-state {
		pins = "gpio86";
		function = "mdp_vsync";
		drive-strength = <2>;
		bias-pull-down;
	};

	dsi_s_te_active: dsi-s-te-active-state {
		pins = "gpio87";
		function = "mdp_vsync";
		drive-strength = <2>;
		bias-pull-down;
	};

	dsi_s_te_suspend: dsi-s-te-suspend-state {
		pins = "gpio87";
		function = "mdp_vsync";
		drive-strength = <2>;
		bias-pull-down;
	};

	wcd_default: wcd-reset-n-active-state {
		pins = "gpio108";
		function = "gpio";
		drive-strength = <16>;
		bias-disable;
	};

	fan_pwr_active: fan-pwr-active-state {
		pins = "gpio109";
		function = "gpio";
		drive-strength = <2>;
		bias-disable;
	};

	audio_mclk0_default_state: audio-mclk0-default-state {
		pins = "gpio125";
		function = "audio_ext_mclk0";
		drive-strength = <8>;
		bias-disable;
		output-high;
	};

	i2s0_default_state: i2s0-default-state {
		sck-pins {
			pins = "gpio126";
			function = "i2s0_sck";
			drive-strength = <8>;
			bias-disable;
			output-high;
		};

		data0-pins {
			pins = "gpio127";
			function = "i2s0_data0";
			drive-strength = <8>;
			bias-disable;
		};

		data1-pins {
			pins = "gpio128";
			function = "i2s0_data1";
			drive-strength = <8>;
			bias-disable;
		};

		ws-pins {
			pins = "gpio129";
			function = "i2s0_ws";
			drive-strength = <8>;
			bias-disable;
			output-high;
		};
	};

	dsi_p_rst_active: dsi-p-rst-active-state {
		pins = "gpio133";
		function = "gpio";
		drive-strength = <8>;
		bias-disable;
	};

	dsi_p_rst_suspend: dsi-p-rst-suspend-state {
		pins = "gpio133";
		function = "gpio";
		drive-strength = <2>;
		bias-pull-down;
	};

	dsi_s_rst_active: dsi-s-rst-active-state {
		pins = "gpio137";
		function = "gpio";
		drive-strength = <8>;
		bias-disable;
	};

	dsi_s_rst_suspend: dsi-s-rst-suspend-state {
		pins = "gpio137";
		function = "gpio";
		drive-strength = <2>;
		bias-pull-down;
	};

	usb0_sbu_default: usb0-sbu-state {
		oe-n-pins {
			pins = "gpio140";
			function = "gpio";
			bias-disable;
			drive-strength = <8>;
			output-high;
		};

		sel-pins {
			pins = "gpio141";
			function = "gpio";
			bias-disable;
			drive-strength = <8>;
		};
	};
};

&uart7 {
	status = "okay";
};

&uart14 {
	status = "okay";

	bluetooth {
		compatible = "qcom,wcn7850-bt";

		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
		vddaon-supply = <&vreg_pmu_aon_0p59>;
		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;

		max-speed = <3200000>;
	};
};

&ufs_mem_hc {
	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
	vcc-supply = <&vreg_l17b_2p5>;
	vcc-max-microamp = <1300000>;
	vccq-supply = <&vreg_l1g_1p2>;
	vccq-max-microamp = <1200000>;
	vdd-hba-supply = <&vreg_l3g_1p2>;

	status = "okay";
};

&ufs_mem_phy {
	vdda-phy-supply = <&vreg_l1d_0p88>;
	vdda-pll-supply = <&vreg_l3e_1p2>;

	status = "okay";
};

&usb_1 {
	status = "okay";
};

&usb_1_dwc3_hs {
	remote-endpoint = <&pmic_glink_hs_in>;
};

&usb_1_hsphy {
	phys = <&pm8550b_eusb2_repeater>;

	vdd-supply = <&vreg_l1e_0p88>;
	vdda12-supply = <&vreg_l3e_1p2>;

	status = "okay";
};

&usb_dp_qmpphy {
	vdda-phy-supply = <&vreg_l3e_1p2>;
	vdda-pll-supply = <&vreg_l3f_0p88>;

	status = "okay";
};

&usb_dp_qmpphy_out {
	remote-endpoint = <&pmic_glink_ss_in>;
};

&xo_board {
	clock-frequency = <76800000>;
};