# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/mediatek,mt6779-pinctrl.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: MediaTek MT6779 Pin Controller
maintainers:
- Andy Teng <andy.teng@mediatek.com>
- AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
- Sean Wang <sean.wang@kernel.org>
- Yassine Oudjana <y.oudjana@protonmail.com>
description:
The MediaTek pin controller on MT6779 is used to control pin functions, pull
up/down resistance and drive strength options.
properties:
compatible:
enum:
- mediatek,mt6735-pinctrl
- mediatek,mt6735m-pinctrl
- mediatek,mt6765-pinctrl
- mediatek,mt6779-pinctrl
- mediatek,mt6795-pinctrl
- mediatek,mt6797-pinctrl
reg:
description: Physical addresses for GPIO base(s) and EINT registers.
reg-names: true
gpio-controller: true
"#gpio-cells":
const: 2
description:
Number of cells in GPIO specifier. Since the generic GPIO binding is used,
the amount of cells must be specified as 2. See the below mentioned gpio
binding representation for description of particular cells.
gpio-ranges:
minItems: 1
maxItems: 5
description:
GPIO valid number range.
interrupt-controller: true
interrupts:
maxItems: 1
description:
Specifies the summary IRQ.
"#interrupt-cells":
const: 2
required:
- compatible
- reg
- reg-names
- gpio-controller
- "#gpio-cells"
allOf:
- $ref: pinctrl.yaml#
- if:
properties:
compatible:
contains:
enum:
- mediatek,mt6735-pinctrl
- mediatek,mt6735m-pinctrl
then:
properties:
reg:
minItems: 8
maxItems: 8
reg-names:
items:
- const: gpio
- const: iocfg0
- const: iocfg1
- const: iocfg2
- const: iocfg3
- const: iocfg4
- const: iocfg5
- const: eint
interrupts:
items:
- description: EINT interrupt
patternProperties:
'-pins$':
patternProperties:
'^pins':
properties:
drive-strength:
enum: [2, 4, 6, 8, 10, 12, 14, 16]
- if:
properties:
compatible:
contains:
const: mediatek,mt6765-pinctrl
then:
properties:
reg:
minItems: 9
maxItems: 9
reg-names:
items:
- const: iocfg0
- const: iocfg1
- const: iocfg2
- const: iocfg3
- const: iocfg4
- const: iocfg5
- const: iocfg6
- const: iocfg7
- const: eint
interrupts:
items:
- description: EINT interrupt
patternProperties:
'-pins$':
patternProperties:
'^pins':
properties:
drive-strength:
enum: [1, 2, 4, 16]
- if:
properties:
compatible:
contains:
const: mediatek,mt6779-pinctrl
then:
properties:
reg:
minItems: 9
maxItems: 9
reg-names:
items:
- const: gpio
- const: iocfg_rm
- const: iocfg_br
- const: iocfg_lm
- const: iocfg_lb
- const: iocfg_rt
- const: iocfg_lt
- const: iocfg_tl
- const: eint
patternProperties:
'-pins$':
patternProperties:
'^pins':
properties:
drive-strength:
enum: [2, 4, 8, 12, 16]
- if:
properties:
compatible:
contains:
const: mediatek,mt6795-pinctrl
then:
properties:
reg:
minItems: 2
maxItems: 2
reg-names:
items:
- const: base
- const: eint
interrupts:
minItems: 1
items:
- description: EINT interrupt
- description: EINT event_b interrupt
patternProperties:
'-pins$':
patternProperties:
'^pins':
properties:
drive-strength:
enum: [2, 4, 6, 8, 10, 12, 14, 16]
- if:
properties:
compatible:
contains:
const: mediatek,mt6797-pinctrl
then:
properties:
reg:
minItems: 5
maxItems: 5
reg-names:
items:
- const: gpio
- const: iocfgl
- const: iocfgb
- const: iocfgr
- const: iocfgt
patternProperties:
'-pins$':
patternProperties:
'^pins':
properties:
drive-strength:
enum: [2, 4, 8, 12, 16]
- if:
properties:
reg-names:
contains:
const: eint
then:
required:
- interrupts
- interrupt-controller
- "#interrupt-cells"
patternProperties:
'-pins$':
type: object
additionalProperties: false
patternProperties:
'^pins':
type: object
description:
A pinctrl node should contain at least one subnode representing the
pinctrl groups available on the machine. Each subnode will list the
pins it needs, and how they should be configured, with regard to
muxer configuration, pullups, drive strength, input enable/disable
and input schmitt.
allOf:
- $ref: pinmux-node.yaml
- $ref: pincfg-node.yaml
properties:
pinmux:
description:
Integer array, represents gpio pin number and mux setting.
Supported pin number and mux varies for different SoCs, and are
defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h
directly.
bias-disable: true
bias-pull-up:
oneOf:
- type: boolean
- enum: [100, 101, 102, 103]
description: Pull up PUPD/R0/R1 type define value.
description:
For normal pull up type, it is not necessary to specify R1R0
values; When pull up type is PUPD/R0/R1, adding R1R0 defines
will set different resistance values.
bias-pull-down:
oneOf:
- type: boolean
- enum: [100, 101, 102, 103]
description: Pull down PUPD/R0/R1 type define value.
description:
For normal pull down type, it is not necessary to specify R1R0
values; When pull down type is PUPD/R0/R1, adding R1R0 defines
will set different resistance values.
input-enable: true
input-disable: true
output-low: true
output-high: true
input-schmitt-enable: true
input-schmitt-disable: true
drive-strength: true
slew-rate:
description: |
Set the slew rate. Valid arguments are described as below:
0: Normal slew rate
1: Slower slew
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1]
mediatek,pull-up-adv:
description: |
Pull up settings for 2 pull resistors, R0 and R1. User can
configure those special pins. Valid arguments are described as
below:
0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1, 2, 3]
mediatek,pull-down-adv:
description: |
Pull down settings for 2 pull resistors, R0 and R1. User can
configure those special pins. Valid arguments are described as
below:
0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1, 2, 3]
required:
- pinmux
additionalProperties: false
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/mt6779-pinfunc.h>
soc {
#address-cells = <2>;
#size-cells = <2>;
pio: pinctrl@10005000 {
compatible = "mediatek,mt6779-pinctrl";
reg = <0 0x10005000 0 0x1000>,
<0 0x11c20000 0 0x1000>,
<0 0x11d10000 0 0x1000>,
<0 0x11e20000 0 0x1000>,
<0 0x11e70000 0 0x1000>,
<0 0x11ea0000 0 0x1000>,
<0 0x11f20000 0 0x1000>,
<0 0x11f30000 0 0x1000>,
<0 0x1000b000 0 0x1000>;
reg-names = "gpio", "iocfg_rm",
"iocfg_br", "iocfg_lm",
"iocfg_lb", "iocfg_rt",
"iocfg_lt", "iocfg_tl",
"eint";
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&pio 0 0 210>;
interrupt-controller;
#interrupt-cells = <2>;
interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;
mmc0_pins_default: mmc0-pins {
pins-cmd-dat {
pinmux = <PINMUX_GPIO168__FUNC_MSDC0_DAT0>,
<PINMUX_GPIO172__FUNC_MSDC0_DAT1>,
<PINMUX_GPIO169__FUNC_MSDC0_DAT2>,
<PINMUX_GPIO177__FUNC_MSDC0_DAT3>,
<PINMUX_GPIO170__FUNC_MSDC0_DAT4>,
<PINMUX_GPIO173__FUNC_MSDC0_DAT5>,
<PINMUX_GPIO171__FUNC_MSDC0_DAT6>,
<PINMUX_GPIO174__FUNC_MSDC0_DAT7>,
<PINMUX_GPIO167__FUNC_MSDC0_CMD>;
input-enable;
mediatek,pull-up-adv = <1>;
};
pins-clk {
pinmux = <PINMUX_GPIO176__FUNC_MSDC0_CLK>;
mediatek,pull-down-adv = <2>;
};
pins-rst {
pinmux = <PINMUX_GPIO178__FUNC_MSDC0_RSTB>;
mediatek,pull-up-adv = <0>;
};
};
/* GPIO0 set as multifunction GPIO0 */
gpio-pins {
pins {
pinmux = <PINMUX_GPIO0__FUNC_GPIO0>;
};
};
/* GPIO52 set as multifunction SDA0 */
i2c0-pins {
pins {
pinmux = <PINMUX_GPIO52__FUNC_SDA0>;
};
};
};
};