// SPDX-License-Identifier: GPL-2.0
/*
* Samsung's Exynos5250 based Arndale board device tree source
*
* Copyright (c) 2013 Samsung Electronics Co., Ltd.
* http://www.samsung.com
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/clock/samsung,s2mps11.h>
#include <dt-bindings/sound/samsung-i2s.h>
#include "exynos5250.dtsi"
/ {
model = "Insignal Arndale evaluation board based on Exynos5250";
compatible = "insignal,arndale", "samsung,exynos5250", "samsung,exynos5";
memory@40000000 {
device_type = "memory";
reg = <0x40000000 0x80000000>;
};
aliases {
mmc0 = &mmc_0;
mmc1 = &mmc_2;
};
chosen {
stdout-path = "serial2:115200n8";
};
gpio-keys {
compatible = "gpio-keys";
key-menu {
label = "SW-TACT2";
gpios = <&gpx1 4 GPIO_ACTIVE_LOW>;
linux,code = <KEY_MENU>;
wakeup-source;
};
key-home {
label = "SW-TACT3";
gpios = <&gpx1 5 GPIO_ACTIVE_LOW>;
linux,code = <KEY_HOME>;
wakeup-source;
};
key-up {
label = "SW-TACT4";
gpios = <&gpx1 6 GPIO_ACTIVE_LOW>;
linux,code = <KEY_UP>;
wakeup-source;
};
key-down {
label = "SW-TACT5";
gpios = <&gpx1 7 GPIO_ACTIVE_LOW>;
linux,code = <KEY_DOWN>;
wakeup-source;
};
key-back {
label = "SW-TACT6";
gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
linux,code = <KEY_BACK>;
wakeup-source;
};
key-wakeup {
label = "SW-TACT7";
gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WAKEUP>;
wakeup-source;
};
};
/*
* For unknown reasons HDMI-DDC does not work with Exynos I2C
* controllers. Lets use software I2C over GPIO pins as a workaround.
*/
i2c_ddc: i2c-10 {
compatible = "i2c-gpio";
pinctrl-names = "default";
pinctrl-0 = <&i2c2_gpio_bus>;
sda-gpios = <&gpa0 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpa0 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
};
panel: panel {
compatible = "boe,hv070wsa-100";
power-supply = <&vcc_3v3_reg>;
enable-gpios = <&gpd1 3 GPIO_ACTIVE_HIGH>;
port {
panel_ep: endpoint {
remote-endpoint = <&bridge_out_ep>;
};
};
};
main_dc_reg: regulator-0 {
compatible = "regulator-fixed";
regulator-name = "MAIN_DC";
regulator-always-on;
};
mmc_reg: regulator-1 {
compatible = "regulator-fixed";
regulator-name = "VDD_MMC";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-always-on;
};
reg_hdmi_en: regulator-2 {
compatible = "regulator-fixed";
regulator-name = "hdmi-en";
regulator-always-on;
};
vcc_1v2_reg: regulator-3 {
compatible = "regulator-fixed";
regulator-name = "VCC_1V2";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
vcc_1v8_reg: regulator-4 {
compatible = "regulator-fixed";
regulator-name = "VCC_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
vcc_3v3_reg: regulator-5 {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
sound {
compatible = "samsung,arndale-wm1811";
samsung,audio-cpu = <&i2s0>;
samsung,audio-codec = <&wm1811>;
};
fixed-rate-clocks {
xxti {
compatible = "samsung,clock-xxti";
clock-frequency = <24000000>;
};
};
// SMSC USB3503 connected in hardware only mode as a PHY
usb_hub: usb-hub {
compatible = "smsc,usb3503a";
reset-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
connect-gpios = <&gpd1 7 GPIO_ACTIVE_HIGH>;
};
};
&clock {
assigned-clocks = <&clock CLK_FOUT_EPLL>;
assigned-clock-rates = <49152000>;
};
&clock_audss {
assigned-clocks = <&clock_audss EXYNOS_MOUT_AUDSS>;
assigned-clock-parents = <&clock CLK_FOUT_EPLL>;
};
&cpu0 {
cpu0-supply = <&buck2_reg>;
};
&dsi_0 {
vddcore-supply = <&ldo8_reg>;
vddio-supply = <&ldo10_reg>;
samsung,pll-clock-frequency = <24000000>;
samsung,burst-clock-frequency = <320000000>;
samsung,esc-clock-frequency = <10000000>;
status = "okay";
bridge@0 {
reg = <0>;
compatible = "toshiba,tc358764";
vddc-supply = <&vcc_1v2_reg>;
vddio-supply = <&vcc_1v8_reg>;
vddlvds-supply = <&vcc_3v3_reg>;
reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <1>;
bridge_out_ep: endpoint {
remote-endpoint = <&panel_ep>;
};
};
};
};
};
&fimd {
status = "okay";
};
&hdmi {
pinctrl-names = "default";
pinctrl-0 = <&hdmi_hpd>;
status = "okay";
ddc = <&i2c_ddc>;
hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
vdd_osc-supply = <&ldo10_reg>;
vdd_pll-supply = <&ldo8_reg>;
vdd-supply = <&ldo8_reg>;
};
&i2c_0 {
status = "okay";
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <20000>;
samsung,i2c-slave-addr = <0x66>;
pmic@66 {
compatible = "samsung,s5m8767-pmic";
reg = <0x66>;
interrupt-parent = <&gpx3>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&s5m8767_irq>;
wakeup-source;
vinb1-supply = <&main_dc_reg>;
vinb2-supply = <&main_dc_reg>;
vinb3-supply = <&main_dc_reg>;
vinb4-supply = <&main_dc_reg>;
vinb5-supply = <&main_dc_reg>;
vinb6-supply = <&main_dc_reg>;
vinb7-supply = <&main_dc_reg>;
vinb8-supply = <&main_dc_reg>;
vinb9-supply = <&main_dc_reg>;
vinl1-supply = <&buck7_reg>;
vinl2-supply = <&buck7_reg>;
vinl3-supply = <&buck7_reg>;
vinl4-supply = <&main_dc_reg>;
vinl5-supply = <&main_dc_reg>;
vinl6-supply = <&main_dc_reg>;
vinl7-supply = <&main_dc_reg>;
vinl8-supply = <&buck8_reg>;
vinl9-supply = <&buck8_reg>;
s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 GPIO_ACTIVE_HIGH>,
<&gpd1 1 GPIO_ACTIVE_HIGH>,
<&gpd1 2 GPIO_ACTIVE_HIGH>;
s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>,
<&gpx2 4 GPIO_ACTIVE_HIGH>,
<&gpx2 5 GPIO_ACTIVE_HIGH>;
s5m8767_osc: clocks {
compatible = "samsung,s5m8767-clk";
#clock-cells = <1>;
clock-output-names = "s5m8767_ap", "unused1", "unused2";
};
regulators {
ldo1_reg: LDO1 {
regulator-name = "VDD_ALIVE_1.0V";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo2_reg: LDO2 {
regulator-name = "VDD_28IO_DP_1.35V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo3_reg: LDO3 {
regulator-name = "VDD_COMMON1_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo4_reg: LDO4 {
regulator-name = "VDD_IOPERI_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
op_mode = <1>;
};
ldo5_reg: LDO5 {
regulator-name = "VDD_EXT_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo6_reg: LDO6 {
regulator-name = "VDD_MPLL_1.1V";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo7_reg: LDO7 {
regulator-name = "VDD_XPLL_1.1V";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo8_reg: LDO8 {
regulator-name = "VDD_COMMON2_1.0V";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo9_reg: LDO9 {
regulator-name = "VDD_33ON_3.0V";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
op_mode = <1>;
};
ldo10_reg: LDO10 {
regulator-name = "VDD_COMMON3_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo11_reg: LDO11 {
regulator-name = "VDD_ABB2_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo12_reg: LDO12 {
regulator-name = "VDD_USB_3.0V";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo13_reg: LDO13 {
regulator-name = "VDDQ_C2C_W_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo14_reg: LDO14 {
regulator-name = "VDD18_ABB0_3_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo15_reg: LDO15 {
regulator-name = "VDD10_COMMON4_1.0V";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo16_reg: LDO16 {
regulator-name = "VDD18_HSIC_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo17_reg: LDO17 {
regulator-name = "VDDQ_MMC2_3_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
ldo18_reg: LDO18 {
regulator-name = "VDD_33ON_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
op_mode = <1>;
};
ldo22_reg: LDO22 {
regulator-name = "EXT_33_OFF";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
op_mode = <1>;
};
ldo23_reg: LDO23 {
regulator-name = "EXT_28_OFF";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
op_mode = <1>;
};
ldo25_reg: LDO25 {
regulator-name = "PVDD_LDO25";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
op_mode = <1>;
};
ldo26_reg: LDO26 {
regulator-name = "EXT_18_OFF";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
op_mode = <1>;
};
buck1_reg: BUCK1 {
regulator-name = "VDD_MIF";
regulator-min-microvolt = <950000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
buck2_reg: BUCK2 {
regulator-name = "VDD_ARM";
regulator-min-microvolt = <912500>;
regulator-max-microvolt = <1300000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
buck3_reg: BUCK3 {
regulator-name = "VDD_INT";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
buck4_reg: BUCK4 {
regulator-name = "VDD_G3D";
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <1300000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
buck5_reg: BUCK5 {
regulator-name = "VDD_MEM_1.35V";
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <1355000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>;
};
buck7_reg: BUCK7 {
regulator-name = "PVDD_BUCK7";
regulator-always-on;
op_mode = <1>;
};
buck8_reg: BUCK8 {
regulator-name = "PVDD_BUCK8";
regulator-always-on;
op_mode = <1>;
};
buck9_reg: BUCK9 {
regulator-name = "VDD_33_OFF_EXT1";
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <3000000>;
op_mode = <1>;
};
};
};
};
&i2c_3 {
status = "okay";
wm1811: audio-codec@1a {
compatible = "wlf,wm1811";
reg = <0x1a>;
clocks = <&i2s0 CLK_I2S_CDCLK>;
clock-names = "MCLK1";
AVDD2-supply = <&main_dc_reg>;
CPVDD-supply = <&main_dc_reg>;
DBVDD1-supply = <&main_dc_reg>;
DBVDD2-supply = <&main_dc_reg>;
DBVDD3-supply = <&main_dc_reg>;
LDO1VDD-supply = <&main_dc_reg>;
SPKVDD1-supply = <&main_dc_reg>;
SPKVDD2-supply = <&main_dc_reg>;
wlf,ldo1ena-gpios = <&gpb0 0 GPIO_ACTIVE_HIGH>;
wlf,ldo2ena-gpios = <&gpb0 1 GPIO_ACTIVE_HIGH>;
};
};
&i2c_8 {
status = "okay";
/* used by HDMI PHY */
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
};
&i2c_9 {
status = "okay";
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <40000>;
};
&i2s0 {
assigned-clocks = <&i2s0 CLK_I2S_RCLK_SRC>;
assigned-clock-parents = <&clock_audss EXYNOS_I2S_BUS>;
status = "okay";
};
&i2s0_bus {
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV2>;
};
&mali {
mali-supply = <&buck4_reg>;
status = "okay";
};
&mixer {
status = "okay";
};
&mmc_0 {
status = "okay";
broken-cd;
card-detect-delay = <200>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
vmmc-supply = <&mmc_reg>;
pinctrl-names = "default";
pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
bus-width = <8>;
cap-mmc-highspeed;
mmc-ddr-1_8v;
};
&mmc_2 {
status = "okay";
card-detect-delay = <200>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
vmmc-supply = <&mmc_reg>;
pinctrl-names = "default";
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
bus-width = <4>;
disable-wp;
cap-sd-highspeed;
};
&pinctrl_0 {
s5m8767_irq: s5m8767-irq-pins {
samsung,pins = "gpx3-2";
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
};
};
&rtc {
clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>;
clock-names = "rtc", "rtc_src";
status = "okay";
};
&sata {
status = "okay";
};
&sata_phy {
status = "okay";
samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
};
&sata_phy_i2c {
status = "okay";
};
&usbdrd {
vdd10-supply = <&ldo15_reg>;
vdd33-supply = <&ldo12_reg>;
};