// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (C) 2013 Pavel Machek <pavel@ucw.cz>
* Copyright (C) 2013-2014 Aaro Koskinen <aaro.koskinen@iki.fi>
*/
/dts-v1/;
#include "omap34xx.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/media/video-interfaces.h>
/*
* Default secure signed bootloader (Nokia X-Loader) does not enable L3 firewall
* for omap AES HW crypto support. When linux kernel try to access memory of AES
* blocks then kernel receive "Unhandled fault: external abort on non-linefetch"
* and crash. Until somebody fix omap-aes.c and omap_hwmod_3xxx_data.c code (no
* crash anymore) omap AES support will be disabled for all Nokia N900 devices.
* There is "unofficial" version of bootloader which enables AES in L3 firewall
* but it is not widely used and to prevent kernel crash rather AES is disabled.
* There is also no runtime detection code if AES is disabled in L3 firewall...
*/
&aes1_target {
status = "disabled";
};
&aes2_target {
status = "disabled";
};
/ {
model = "Nokia N900";
compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3";
aliases {
i2c0;
i2c1 = &i2c1;
i2c2 = &i2c2;
i2c3 = &i2c3;
display0 = &lcd;
display1 = &tv;
};
cpus {
cpu@0 {
cpu0-supply = <&vcc>;
};
};
leds {
compatible = "gpio-leds";
led-heartbeat {
label = "debug::sleep";
gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* 162 */
linux,default-trigger = "default-on";
pinctrl-names = "default";
pinctrl-0 = <&debug_leds>;
};
};
memory@80000000 {
device_type = "memory";
reg = <0x80000000 0x10000000>; /* 256 MB */
};
gpio_keys {
compatible = "gpio-keys";
camera_lens_cover {
label = "Camera Lens Cover";
gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
linux,input-type = <EV_SW>;
linux,code = <SW_CAMERA_LENS_COVER>;
linux,can-disable;
};
camera_focus {
label = "Camera Focus";
gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
linux,code = <KEY_CAMERA_FOCUS>;
linux,can-disable;
};
camera_capture {
label = "Camera Capture";
gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
linux,code = <KEY_CAMERA>;
linux,can-disable;
};
lock_button {
label = "Lock Button";
gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
linux,code = <KEY_SCREENLOCK>;
linux,can-disable;
};
keypad_slide {
label = "Keypad Slide";
gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
linux,input-type = <EV_SW>;
linux,code = <SW_KEYPAD_SLIDE>;
linux,can-disable;
};
proximity_sensor {
label = "Proximity Sensor";
gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
linux,input-type = <EV_SW>;
linux,code = <SW_FRONT_PROXIMITY>;
linux,can-disable;
};
machine_cover {
label = "Machine Cover";
gpios = <&gpio6 0 GPIO_ACTIVE_LOW>; /* 160 */
linux,input-type = <EV_SW>;
linux,code = <SW_MACHINE_COVER>;
linux,can-disable;
};
};
isp1707: isp1707 {
compatible = "nxp,isp1707";
nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
usb-phy = <&usb2_phy>;
};
tv: connector {
compatible = "composite-video-connector";
label = "tv";
port {
tv_connector_in: endpoint {
remote-endpoint = <&venc_out>;
};
};
};
sound: n900-audio {
compatible = "nokia,n900-audio";
nokia,cpu-dai = <&mcbsp2>;
nokia,audio-codec = <&tlv320aic3x>, <&tlv320aic3x_aux>;
nokia,headphone-amplifier = <&tpa6130a2>;
tvout-selection-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; /* 40 */
jack-detection-gpios = <&gpio6 17 GPIO_ACTIVE_HIGH>; /* 177 */
eci-switch-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* 182 */
speaker-amplifier-gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>;
};
battery: n900-battery {
compatible = "nokia,n900-battery";
io-channels = <&twl_madc 0>, <&twl_madc 4>, <&twl_madc 12>;
io-channel-names = "temp", "bsi", "vbat";
};
pwm9: pwm-9 {
compatible = "ti,omap-dmtimer-pwm";
#pwm-cells = <3>;
ti,timers = <&timer9>;
ti,clock-source = <0x00>; /* timer_sys_ck */
};
ir: n900-ir {
compatible = "nokia,n900-ir";
pwms = <&pwm9 0 26316 0>; /* 38000 Hz */
};
rom_rng: rng {
compatible = "nokia,n900-rom-rng";
clocks = <&rng_ick>;
clock-names = "ick";
};
/* controlled (enabled/disabled) directly by bcm2048 and wl1251 */
vctcxo: vctcxo {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <38400000>;
};
};
&isp {
vdds_csib-supply = <&vaux2>;
pinctrl-names = "default";
pinctrl-0 = <&camera_pins>;
ports {
port@1 {
reg = <1>;
csi_isp: endpoint {
remote-endpoint = <&csi_cam1>;
bus-type = <MEDIA_BUS_TYPE_CCP2>;
clock-lanes = <1>;
data-lanes = <0>;
lane-polarity = <0 0>;
/* Select strobe = <1> for back camera, <0> for front camera */
strobe = <1>;
};
};
};
};
&omap3_pmx_core {
pinctrl-names = "default";
uart2_pins: uart2-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts */
OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts */
OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx */
>;
};
uart3_pins: uart3-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx */
OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
>;
};
ethernet_pins: ethernet-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20b4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* gpmc_ncs3.gpio_54 */
OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE4) /* dss_data16.gpio_86 */
OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */
>;
};
gpmc_pins: gpmc-pins {
pinctrl-single,pins = <
/* address lines */
OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0) /* gpmc_a1.gpmc_a1 */
OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0) /* gpmc_a2.gpmc_a2 */
OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0) /* gpmc_a3.gpmc_a3 */
/* data lines, gpmc_d0..d7 not muxable according to TRM */
OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0) /* gpmc_d8.gpmc_d8 */
OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0) /* gpmc_d9.gpmc_d9 */
OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0) /* gpmc_d10.gpmc_d10 */
OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0) /* gpmc_d11.gpmc_d11 */
OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0) /* gpmc_d12.gpmc_d12 */
OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0) /* gpmc_d13.gpmc_d13 */
OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0) /* gpmc_d14.gpmc_d14 */
OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0) /* gpmc_d15.gpmc_d15 */
/*
* gpmc_ncs0, gpmc_nadv_ale, gpmc_noe, gpmc_nwe, gpmc_wait0 not muxable
* according to TRM. OneNAND seems to require PIN_INPUT on clock.
*/
OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs1.gpmc_ncs1 */
OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0) /* gpmc_clk.gpmc_clk */
>;
};
i2c1_pins: i2c1-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl */
OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda */
>;
};
i2c2_pins: i2c2-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
>;
};
i2c3_pins: i2c3-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */
OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */
>;
};
debug_leds: debug-led-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_clkx.gpio_162 */
>;
};
mcspi4_pins: mcspi4-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x218c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */
OMAP3_CORE1_IOPAD(0x2192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */
OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */
OMAP3_CORE1_IOPAD(0x2196, PIN_OUTPUT | MUX_MODE1) /* mcspi4_cs0 */
>;
};
mmc1_pins: mmc1-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
>;
};
mmc2_pins: mmc2-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */
OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */
OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */
OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */
OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */
OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */
OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */
OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */
OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */
OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */
>;
};
acx565akm_pins: acx565akm-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */
>;
};
dss_sdi_pins: dss-sdi-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE1) /* dss_data10.sdi_dat1n */
OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE1) /* dss_data11.sdi_dat1p */
OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE1) /* dss_data12.sdi_dat2n */
OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE1) /* dss_data13.sdi_dat2p */
OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE1) /* dss_data22.sdi_clkp */
OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE1) /* dss_data23.sdi_clkn */
>;
};
wl1251_pins: wl1251-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE4) /* gpio 87 => wl1251 enable */
OMAP3_CORE1_IOPAD(0x208a, PIN_INPUT | MUX_MODE4) /* gpio 42 => wl1251 irq */
>;
};
ssi_pins: ssi-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1) /* ssi1_rdy_tx */
OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1) /* ssi1_flag_tx */
OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE4) /* ssi1_wake_tx (cawake) */
OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1) /* ssi1_dat_tx */
OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE1) /* ssi1_dat_rx */
OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE1) /* ssi1_flag_rx */
OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE1) /* ssi1_rdy_rx */
OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE1) /* ssi1_wake */
>;
};
modem_pins: modem-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE4) /* gpio 70 => cmt_apeslpx */
OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | MUX_MODE4) /* gpio 72 => ape_rst_rq */
OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4) /* gpio 73 => cmt_rst_rq */
OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE4) /* gpio 74 => cmt_en */
OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE4) /* gpio 75 => cmt_rst */
OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* gpio 157 => cmt_bsi */
>;
};
camera_pins: camera-pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x210c, PIN_OUTPUT | MUX_MODE7) /* cam_hs */
OMAP3_CORE1_IOPAD(0x210e, PIN_OUTPUT | MUX_MODE7) /* cam_vs */
OMAP3_CORE1_IOPAD(0x2110, PIN_OUTPUT | MUX_MODE0) /* cam_xclka */
OMAP3_CORE1_IOPAD(0x211e, PIN_OUTPUT | MUX_MODE7) /* cam_d4 */
OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0) /* cam_d6 */
OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0) /* cam_d7 */
OMAP3_CORE1_IOPAD(0x2126, PIN_INPUT | MUX_MODE0) /* cam_d8 */
OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT | MUX_MODE0) /* cam_d9 */
OMAP3_CORE1_IOPAD(0x212a, PIN_OUTPUT | MUX_MODE7) /* cam_d10 */
OMAP3_CORE1_IOPAD(0x212e, PIN_OUTPUT | MUX_MODE7) /* cam_xclkb */
OMAP3_CORE1_IOPAD(0x2132, PIN_OUTPUT | MUX_MODE0) /* cam_strobe */
>;
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <2200000>;
twl: twl@48 {
reg = <0x48>;
interrupts = <7>; /* SYS_NIRQ cascaded to intc */
interrupt-parent = <&intc>;
};
};
#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"
&vaux1 {
regulator-name = "V28";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
regulator-always-on; /* due to battery cover sensor */
};
&vaux2 {
regulator-name = "VCSI";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
};
&vaux3 {
regulator-name = "VMMC2_30";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <3000000>;
regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
};
&vaux4 {
regulator-name = "VCAM_ANA_28";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
};
&vmmc1 {
regulator-name = "VMMC1";
regulator-min-microvolt = <1850000>;
regulator-max-microvolt = <3150000>;
regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
};
&vmmc2 {
regulator-name = "V28_A";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <3000000>;
regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
regulator-always-on; /* due VIO leak to AIC34 VDDs */
};
&vpll1 {
regulator-name = "VPLL";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
regulator-always-on;
};
&vpll2 {
regulator-name = "VSDI_CSI";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
regulator-always-on;
};
&vsim {
regulator-name = "VMMC2_IO_18";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
};
&vio {
regulator-name = "VIO";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
&vintana1 {
regulator-name = "VINTANA1";
/* fixed to 1500000 */
regulator-always-on;
};
&vintana2 {
regulator-name = "VINTANA2";
regulator-min-microvolt = <2750000>;
regulator-max-microvolt = <2750000>;
regulator-always-on;
};
&vintdig {
regulator-name = "VINTDIG";
/* fixed to 1500000 */
regulator-always-on;
};
/* First two dma channels are reserved on secure omap3 */
&sdma {
dma-channel-mask = <0xfffffffc>;
};
&twl {
twl_audio: audio {
compatible = "ti,twl4030-audio";
ti,enable-vibra = <1>;
};
twl_power: power {
compatible = "ti,twl4030-power-n900", "ti,twl4030-power-idle-osc-off";
ti,use_poweroff;
};
};
&twl_keypad {
linux,keymap = < MATRIX_KEY(0x00, 0x00, KEY_Q)
MATRIX_KEY(0x00, 0x01, KEY_O)
MATRIX_KEY(0x00, 0x02, KEY_P)
MATRIX_KEY(0x00, 0x03, KEY_COMMA)
MATRIX_KEY(0x00, 0x04, KEY_BACKSPACE)
MATRIX_KEY(0x00, 0x06, KEY_A)
MATRIX_KEY(0x00, 0x07, KEY_S)
MATRIX_KEY(0x01, 0x00, KEY_W)
MATRIX_KEY(0x01, 0x01, KEY_D)
MATRIX_KEY(0x01, 0x02, KEY_F)
MATRIX_KEY(0x01, 0x03, KEY_G)
MATRIX_KEY(0x01, 0x04, KEY_H)
MATRIX_KEY(0x01, 0x05, KEY_J)
MATRIX_KEY(0x01, 0x06, KEY_K)
MATRIX_KEY(0x01, 0x07, KEY_L)
MATRIX_KEY(0x02, 0x00, KEY_E)
MATRIX_KEY(0x02, 0x01, KEY_DOT)
MATRIX_KEY(0x02, 0x02, KEY_UP)
MATRIX_KEY(0x02, 0x03, KEY_ENTER)
MATRIX_KEY(0x02, 0x05, KEY_Z)
MATRIX_KEY(0x02, 0x06, KEY_X)
MATRIX_KEY(0x02, 0x07, KEY_C)
MATRIX_KEY(0x02, 0x08, KEY_F9)
MATRIX_KEY(0x03, 0x00, KEY_R)
MATRIX_KEY(0x03, 0x01, KEY_V)
MATRIX_KEY(0x03, 0x02, KEY_B)
MATRIX_KEY(0x03, 0x03, KEY_N)
MATRIX_KEY(0x03, 0x04, KEY_M)
MATRIX_KEY(0x03, 0x05, KEY_SPACE)
MATRIX_KEY(0x03, 0x06, KEY_SPACE)
MATRIX_KEY(0x03, 0x07, KEY_LEFT)
MATRIX_KEY(0x04, 0x00, KEY_T)
MATRIX_KEY(0x04, 0x01, KEY_DOWN)
MATRIX_KEY(0x04, 0x02, KEY_RIGHT)
MATRIX_KEY(0x04, 0x04, KEY_LEFTCTRL)
MATRIX_KEY(0x04, 0x05, KEY_RIGHTALT)
MATRIX_KEY(0x04, 0x06, KEY_LEFTSHIFT)
MATRIX_KEY(0x04, 0x08, KEY_F10)
MATRIX_KEY(0x05, 0x00, KEY_Y)
MATRIX_KEY(0x05, 0x08, KEY_F11)
MATRIX_KEY(0x06, 0x00, KEY_U)
MATRIX_KEY(0x07, 0x00, KEY_I)
MATRIX_KEY(0x07, 0x01, KEY_F7)
MATRIX_KEY(0x07, 0x02, KEY_F8)
>;
};
&twl_gpio {
ti,pullups = <0x0>;
ti,pulldowns = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
clock-frequency = <100000>;
tlv320aic3x: tlv320aic3x@18 {
compatible = "ti,tlv320aic3x";
reg = <0x18>;
reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */
ai3x-gpio-func = <
0 /* AIC3X_GPIO1_FUNC_DISABLED */
5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
>;
AVDD-supply = <&vmmc2>;
DRVDD-supply = <&vmmc2>;
IOVDD-supply = <&vio>;
DVDD-supply = <&vio>;
ai3x-micbias-vg = <1>;
};
tlv320aic3x_aux: tlv320aic3x@19 {
compatible = "ti,tlv320aic3x";
reg = <0x19>;
reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */
AVDD-supply = <&vmmc2>;
DRVDD-supply = <&vmmc2>;
IOVDD-supply = <&vio>;
DVDD-supply = <&vio>;
ai3x-micbias-vg = <2>;
};
tsl2563: tsl2563@29 {
compatible = "amstaos,tsl2563";
reg = <0x29>;
amstaos,cover-comp-gain = <16>;
};
adp1653: led-controller@30 {
compatible = "adi,adp1653";
reg = <0x30>;
enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */
flash {
flash-timeout-us = <500000>;
flash-max-microamp = <320000>;
led-max-microamp = <50000>;
};
indicator {
led-max-microamp = <17500>;
};
};
lp5523: lp5523@32 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "national,lp5523";
reg = <0x32>;
clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
enable-gpios = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
led@0 {
reg = <0>;
chan-name = "lp5523:kb1";
led-cur = /bits/ 8 <50>;
max-cur = /bits/ 8 <100>;
color = <LED_COLOR_ID_WHITE>;
function = LED_FUNCTION_KBD_BACKLIGHT;
};
led@1 {
reg = <1>;
chan-name = "lp5523:kb2";
led-cur = /bits/ 8 <50>;
max-cur = /bits/ 8 <100>;
color = <LED_COLOR_ID_WHITE>;
function = LED_FUNCTION_KBD_BACKLIGHT;
};
led@2 {
reg = <2>;
chan-name = "lp5523:kb3";
led-cur = /bits/ 8 <50>;
max-cur = /bits/ 8 <100>;
color = <LED_COLOR_ID_WHITE>;
function = LED_FUNCTION_KBD_BACKLIGHT;
};
led@3 {
reg = <3>;
chan-name = "lp5523:kb4";
led-cur = /bits/ 8 <50>;
max-cur = /bits/ 8 <100>;
color = <LED_COLOR_ID_WHITE>;
function = LED_FUNCTION_KBD_BACKLIGHT;
};
led@4 {
reg = <4>;
chan-name = "lp5523:b";
led-cur = /bits/ 8 <50>;
max-cur = /bits/ 8 <100>;
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_STATUS;
};
led@5 {
reg = <5>;
chan-name = "lp5523:g";
led-cur = /bits/ 8 <50>;
max-cur = /bits/ 8 <100>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_STATUS;
};
led@6 {
reg = <6>;
chan-name = "lp5523:r";
led-cur = /bits/ 8 <50>;
max-cur = /bits/ 8 <100>;
color = <LED_COLOR_ID_RED>;
function = LED_FUNCTION_STATUS;
};
led@7 {
reg = <7>;
chan-name = "lp5523:kb5";
led-cur = /bits/ 8 <50>;
max-cur = /bits/ 8 <100>;
color = <LED_COLOR_ID_WHITE>;
function = LED_FUNCTION_KBD_BACKLIGHT;
};
led@8 {
reg = <8>;
chan-name = "lp5523:kb6";
led-cur = /bits/ 8 <50>;
max-cur = /bits/ 8 <100>;
color = <LED_COLOR_ID_WHITE>;
function = LED_FUNCTION_KBD_BACKLIGHT;
};
};
bq27200: bq27200@55 {
compatible = "ti,bq27200";
reg = <0x55>;
power-supplies = <&bq24150a>;
};
/* Stereo headphone amplifier */
tpa6130a2: tpa6130a2@60 {
compatible = "ti,tpa6130a2";
reg = <0x60>;
Vdd-supply = <&vmmc2>;
power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* 98 */
};
si4713: si4713@63 {
compatible = "silabs,si4713";
reg = <0x63>;
interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */
reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */
vio-supply = <&vio>;
vdd-supply = <&vaux1>;
};
bq24150a: bq24150a@6b {
compatible = "ti,bq24150a";
reg = <0x6b>;
ti,current-limit = <100>;
ti,weak-battery-voltage = <3400>;
ti,battery-regulation-voltage = <4200>;
ti,charge-current = <650>;
ti,termination-current = <100>;
ti,resistor-sense = <68>;
ti,usb-charger-detection = <&isp1707>;
};
};
&i2c3 {
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins>;
clock-frequency = <400000>;
accelerometer@1d {
compatible = "st,lis302dl";
reg = <0x1d>;
vdd-supply = <&vaux1>;
vddio-supply = <&vio>;
interrupt-parent = <&gpio6>;
interrupts = <21 IRQ_TYPE_EDGE_RISING>,
<20 IRQ_TYPE_EDGE_RISING>; /* 181 and 180 */
mount-matrix = "-1", "0", "0",
"0", "1", "0",
"0", "0", "1";
};
cam1: camera@3e {
compatible = "toshiba,et8ek8";
reg = <0x3e>;
vana-supply = <&vaux4>;
clocks = <&isp 0>;
clock-names = "extclk";
clock-frequency = <9600000>;
reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */
lens-focus = <&ad5820>;
port {
csi_cam1: endpoint {
bus-type = <MEDIA_BUS_TYPE_CCP2>;
strobe = <1>;
clock-inv = <0>;
crc = <1>;
remote-endpoint = <&csi_isp>;
};
};
};
/* D/A converter for auto-focus */
ad5820: dac@c {
compatible = "adi,ad5820";
reg = <0x0c>;
VANA-supply = <&vaux4>;
#io-channel-cells = <0>;
};
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
vmmc-supply = <&vmmc1>;
bus-width = <4>;
};
/* most boards use vaux3, only some old versions use vmmc2 instead */
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <&vaux3>;
vqmmc-supply = <&vsim>;
bus-width = <8>;
non-removable;
no-sdio;
no-sd;
};
&mmc3 {
status = "disabled";
};
&gpmc {
ranges = <0 0 0x01000000 0x01000000>, /* 16 MB for OneNAND */
<1 0 0x02000000 0x01000000>; /* 16 MB for smc91c96 */
pinctrl-names = "default";
pinctrl-0 = <&gpmc_pins>;
/* sys_ndmareq1 could be used by the driver, not as gpio65 though */
onenand@0,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "ti,omap2-onenand";
reg = <0 0 0x20000>; /* CS0, offset 0, IO size 128K */
/*
* These timings are based on CONFIG_OMAP_GPMC_DEBUG=y reported
* bootloader set values when booted with v5.1
* (OneNAND Manufacturer: Samsung):
*
* cs0 GPMC_CS_CONFIG1: 0xfb001202
* cs0 GPMC_CS_CONFIG2: 0x00111100
* cs0 GPMC_CS_CONFIG3: 0x00020200
* cs0 GPMC_CS_CONFIG4: 0x11001102
* cs0 GPMC_CS_CONFIG5: 0x03101616
* cs0 GPMC_CS_CONFIG6: 0x90060000
*/
gpmc,sync-read;
gpmc,sync-write;
gpmc,burst-length = <16>;
gpmc,burst-read;
gpmc,burst-wrap;
gpmc,burst-write;
gpmc,device-width = <2>;
gpmc,mux-add-data = <2>;
gpmc,cs-on-ns = <0>;
gpmc,cs-rd-off-ns = <102>;
gpmc,cs-wr-off-ns = <102>;
gpmc,adv-on-ns = <0>;
gpmc,adv-rd-off-ns = <12>;
gpmc,adv-wr-off-ns = <12>;
gpmc,oe-on-ns = <12>;
gpmc,oe-off-ns = <102>;
gpmc,we-on-ns = <0>;
gpmc,we-off-ns = <102>;
gpmc,rd-cycle-ns = <132>;
gpmc,wr-cycle-ns = <132>;
gpmc,access-ns = <96>;
gpmc,page-burst-access-ns = <18>;
gpmc,bus-turnaround-ns = <0>;
gpmc,cycle2cycle-delay-ns = <0>;
gpmc,wait-monitoring-ns = <0>;
gpmc,clk-activation-ns = <6>;
gpmc,wr-data-mux-bus-ns = <36>;
gpmc,wr-access-ns = <96>;
gpmc,sync-clk-ps = <15000>;
/*
* MTD partition table corresponding to Nokia's
* Maemo 5 (Fremantle) release.
*/
partition@0 {
label = "bootloader";
reg = <0x00000000 0x00020000>;
read-only;
};
partition@1 {
label = "config";
reg = <0x00020000 0x00060000>;
};
partition@2 {
label = "log";
reg = <0x00080000 0x00040000>;
};
partition@3 {
label = "kernel";
reg = <0x000c0000 0x00200000>;
};
partition@4 {
label = "initfs";
reg = <0x002c0000 0x00200000>;
};
partition@5 {
label = "rootfs";
reg = <0x004c0000 0x0fb40000>;
};
};
/* Ethernet is on some early development boards and qemu */
ethernet@gpmc {
compatible = "smsc,lan91c94";
interrupt-parent = <&gpio2>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; /* gpio54 */
reg = <1 0 0xf>; /* 16 byte IO range */
bank-width = <2>;
pinctrl-names = "default";
pinctrl-0 = <ðernet_pins>;
power-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; /* gpio86 */
reset-gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* gpio164 */
gpmc,device-width = <2>;
gpmc,sync-clk-ps = <0>;
gpmc,cs-on-ns = <0>;
gpmc,cs-rd-off-ns = <48>;
gpmc,cs-wr-off-ns = <24>;
gpmc,adv-on-ns = <0>;
gpmc,adv-rd-off-ns = <0>;
gpmc,adv-wr-off-ns = <0>;
gpmc,we-on-ns = <12>;
gpmc,we-off-ns = <18>;
gpmc,oe-on-ns = <12>;
gpmc,oe-off-ns = <48>;
gpmc,page-burst-access-ns = <0>;
gpmc,access-ns = <42>;
gpmc,rd-cycle-ns = <180>;
gpmc,wr-cycle-ns = <180>;
gpmc,bus-turnaround-ns = <0>;
gpmc,cycle2cycle-delay-ns = <0>;
gpmc,wait-monitoring-ns = <0>;
gpmc,clk-activation-ns = <0>;
gpmc,wr-access-ns = <0>;
gpmc,wr-data-mux-bus-ns = <12>;
};
};
&mcspi1 {
/*
* For some reason, touchscreen is necessary for screen to work at
* all on real hw. It works well without it on emulator.
*
* Also... order in the device tree actually matters here.
*/
tsc2005@0 {
compatible = "ti,tsc2005";
spi-max-frequency = <6000000>;
reg = <0>;
vio-supply = <&vio>;
reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */
interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */
touchscreen-fuzz-x = <4>;
touchscreen-fuzz-y = <7>;
touchscreen-fuzz-pressure = <2>;
touchscreen-size-x = <4096>;
touchscreen-size-y = <4096>;
touchscreen-max-pressure = <2048>;
ti,x-plate-ohms = <280>;
ti,esd-recovery-timeout-ms = <8000>;
};
lcd: acx565akm@2 {
compatible = "sony,acx565akm";
spi-max-frequency = <6000000>;
reg = <2>;
pinctrl-names = "default";
pinctrl-0 = <&acx565akm_pins>;
label = "lcd";
reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
port {
lcd_in: endpoint {
remote-endpoint = <&sdi_out>;
};
};
};
};
&mcspi4 {
pinctrl-names = "default";
pinctrl-0 = <&mcspi4_pins>;
wl1251@0 {
pinctrl-names = "default";
pinctrl-0 = <&wl1251_pins>;
vio-supply = <&vio>;
compatible = "ti,wl1251";
reg = <0>;
spi-max-frequency = <48000000>;
spi-cpol;
spi-cpha;
ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */
interrupt-parent = <&gpio2>;
interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */
clocks = <&vctcxo>;
};
};
/* RNG not directly accessible on n900, see omap3-rom-rng instead */
&rng_target {
status = "disabled";
};
&usb_otg_hs {
interface-type = <0>;
usb-phy = <&usb2_phy>;
phys = <&usb2_phy>;
phy-names = "usb2-phy";
mode = <2>;
power = <50>;
};
&uart1 {
status = "disabled";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
bcm2048: bluetooth {
compatible = "brcm,bcm2048-nokia", "nokia,h4p-bluetooth";
reset-gpios = <&gpio3 27 GPIO_ACTIVE_LOW>; /* 91 */
host-wakeup-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* 101 */
bluetooth-wakeup-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* 37 */
clocks = <&vctcxo>;
clock-names = "sysclk";
};
};
&uart3 {
interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
};
&dss {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_sdi_pins>;
vdds_sdi-supply = <&vaux1>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <1>;
sdi_out: endpoint {
remote-endpoint = <&lcd_in>;
datapairs = <2>;
};
};
};
};
&venc {
status = "okay";
vdda-supply = <&vdac>;
port {
venc_out: endpoint {
remote-endpoint = <&tv_connector_in>;
ti,channels = <1>;
};
};
};
&mcbsp2 {
status = "okay";
};
&ssi_port1 {
pinctrl-names = "default";
pinctrl-0 = <&ssi_pins>;
ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */
modem: hsi-client {
compatible = "nokia,n900-modem";
pinctrl-names = "default";
pinctrl-0 = <&modem_pins>;
hsi-channel-ids = <0>, <1>, <2>, <3>;
hsi-channel-names = "mcsaab-control",
"speech-control",
"speech-data",
"mcsaab-data";
hsi-speed-kbps = <55000>;
hsi-mode = "frame";
hsi-flow = "synchronized";
hsi-arb-mode = "round-robin";
interrupts-extended = <&gpio3 8 IRQ_TYPE_EDGE_FALLING>; /* 72 */
gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>, /* 70 */
<&gpio3 9 GPIO_ACTIVE_HIGH>, /* 73 */
<&gpio3 10 GPIO_ACTIVE_HIGH>, /* 74 */
<&gpio3 11 GPIO_ACTIVE_HIGH>, /* 75 */
<&gpio5 29 GPIO_ACTIVE_HIGH>; /* 157 */
gpio-names = "cmt_apeslpx",
"cmt_rst_rq",
"cmt_en",
"cmt_rst",
"cmt_bsi";
};
};
&ssi_port2 {
status = "disabled";
};