// SPDX-License-Identifier: GPL-2.0-only OR MIT
/*
* Copyright (C) 2026 PHYTEC America LLC
* Author: Nathan Morrisson <nmorrisson@phytec.com>
*/
/dts-v1/;
#include <dt-bindings/input/input.h>
#include <dt-bindings/phy/phy.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include "k3-serdes.h"
#include "k3-j722s.dtsi"
#include "k3-am67-phycore-som.dtsi"
/ {
compatible = "phytec,am6754-phyboard-rigel",
"phytec,am67-phycore-som", "ti,j722s";
model = "PHYTEC phyBOARD-Rigel AM67";
aliases {
gpio1 = &main_gpio1;
mmc1 = &sdhci1;
serial2 = &main_uart0;
usb0 = &usb0;
usb1 = &usb1;
};
can_tc0: can-phy0 {
compatible = "ti,tcan1042";
#phy-cells = <0>;
max-bitrate = <8000000>;
standby-gpios = <&gpio_exp1 1 GPIO_ACTIVE_HIGH>;
};
usb0_connector: connector {
compatible = "gpio-usb-b-connector", "usb-b-connector";
label = "USB-C";
data-role = "dual";
pinctrl-names = "default";
pinctrl-0 = <&main_usbc_power_pins_default>;
id-gpios = <&main_gpio1 15 GPIO_ACTIVE_HIGH>;
port {
usb0_con: endpoint {
remote-endpoint = <&usb0_ep>;
};
};
};
keys {
compatible = "gpio-keys";
autorepeat;
pinctrl-names = "default";
pinctrl-0 = <&gpio_keys_pins_default>;
key-home {
label = "home";
linux,code = <KEY_HOME>;
gpios = <&main_gpio1 23 GPIO_ACTIVE_HIGH>;
};
key-menu {
label = "menu";
linux,code = <KEY_MENU>;
gpios = <&gpio_exp1 4 GPIO_ACTIVE_HIGH>;
};
};
vcc_1v8: regulator-vcc-1v8 {
compatible = "regulator-fixed";
regulator-name = "VCC_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
vcc_3v3_aud: regulator-vcc-3v3-aud {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3_AUD";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
};
vcc_3v3_mmc: regulator-vcc-3v3-mmc {
/* TPS22963C OUTPUT */
compatible = "regulator-fixed";
regulator-name = "VCC_3V3_MMC";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
};
vcc_3v3_sw: regulator-vcc-3v3-sw {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3_SW";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
};
vcc_speaker: regulator-vcc-speaker {
compatible = "regulator-fixed";
regulator-name = "VCC_SPEAKER";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
regulator-boot-on;
};
sound {
compatible = "simple-audio-card";
simple-audio-card,widgets =
"Microphone", "Mic Jack",
"Headphone", "Headphone Jack",
"Line", "Stereo Jack",
"Speaker", "L SPKR",
"Speaker", "R SPKR";
simple-audio-card,routing =
"MIC1RP", "Mic Jack",
"Mic Jack", "MICBIAS",
"Headphone Jack", "HPL",
"Headphone Jack", "HPR",
"MIC1LM", "Stereo Jack",
"MIC1LP", "Stereo Jack",
"L SPKR", "SPL",
"R SPKR", "SPR";
simple-audio-card,name = "phyBOARD-Rigel";
simple-audio-card,format = "dsp_b";
simple-audio-card,bitclock-master = <&sound_master>;
simple-audio-card,frame-master = <&sound_master>;
simple-audio-card,bitclock-inversion;
simple-audio-card,cpu {
sound-dai = <&mcasp0>;
};
sound_master: simple-audio-card,codec {
sound-dai = <&audio_codec>;
clocks = <&audio_refclk1>;
};
};
};
&main_pmx0 {
audio_ext_refclk1_pins_default: audio-ext-refclk1-default-pins {
pinctrl-single,pins = <
J722S_IOPAD(0x0a0, PIN_OUTPUT, 1) /* (N24) GPMC0_WPn.AUDIO_EXT_REFCLK1 */
>;
};
gpio_exp0_int_pins_default: gpio-exp0-int-default-pins {
pinctrl-single,pins = <
J722S_IOPAD(0x0054, PIN_INPUT, 7) /* (T21) GPMC0_AD6.GPIO0_21 */
>;
};
gpio_exp1_int_pins_default: gpio-exp1-int-default-pins {
pinctrl-single,pins = <
J722S_IOPAD(0x0244, PIN_INPUT, 7) /* (A24) MMC1_SDWP.GPIO1_49 */
>;
};
gpio_exp2_int_pins_default: gpio-exp2-int-default-pins {
pinctrl-single,pins = <
J722S_IOPAD(0x0050, PIN_INPUT, 7) /* (T24) GPMC0_AD5.GPIO0_20 */
>;
};
gpio_keys_pins_default: gpio-keys-default-pins {
pinctrl-single,pins = <
J722S_IOPAD(0x01d4, PIN_INPUT, 7) /* (B21) UART0_RTSn.GPIO1_23 */
>;
};
main_i2c0_pins_default: main-i2c0-default-pins {
pinctrl-single,pins = <
J722S_IOPAD(0x01e0, PIN_INPUT_PULLUP, 0) /* (D23) I2C0_SCL */
J722S_IOPAD(0x01e4, PIN_INPUT_PULLUP, 0) /* (B22) I2C0_SDA */
>;
bootph-all;
};
main_i2c1_pins_default: main-i2c1-default-pins {
pinctrl-single,pins = <
J722S_IOPAD(0x01e8, PIN_INPUT_PULLUP, 0) /* (C24) I2C1_SCL */
J722S_IOPAD(0x01ec, PIN_INPUT_PULLUP, 0) /* (A22) I2C1_SDA */
>;
bootph-all;
};
main_mcan0_pins_default: main-mcan0-default-pins {
pinctrl-single,pins = <
J722S_IOPAD(0x1dc, PIN_INPUT, 0) /* (C22) MCAN0_RX */
J722S_IOPAD(0x1d8, PIN_OUTPUT, 0) /* (D22) MCAN0_TX */
>;
};
main_mcasp0_pins_default: main-mcasp0-default-pins {
pinctrl-single,pins = <
J722S_IOPAD(0x1a8, PIN_INPUT, 0) /* (C26) MCASP0_AFSX */
J722S_IOPAD(0x1a4, PIN_INPUT, 0) /* (D25) MCASP0_ACLKX */
J722S_IOPAD(0x198, PIN_OUTPUT, 0) /* (A26) MCASP0_AXR2 */
J722S_IOPAD(0x194, PIN_INPUT, 0) /* (A25) MCASP0_AXR3 */
>;
};
main_mmc1_pins_default: main-mmc1-default-pins {
pinctrl-single,pins = <
J722S_IOPAD(0x023c, PIN_INPUT, 0) /* (H22) MMC1_CMD */
J722S_IOPAD(0x0234, PIN_INPUT, 0) /* (H24) MMC1_CLK */
J722S_IOPAD(0x0230, PIN_INPUT, 0) /* (H23) MMC1_DAT0 */
J722S_IOPAD(0x022c, PIN_INPUT, 0) /* (H20) MMC1_DAT1 */
J722S_IOPAD(0x0228, PIN_INPUT, 0) /* (J23) MMC1_DAT2 */
J722S_IOPAD(0x0224, PIN_INPUT, 0) /* (H25) MMC1_DAT3 */
J722S_IOPAD(0x0240, PIN_INPUT, 0) /* (B24) MMC1_SDCD */
>;
bootph-all;
};
main_uart0_pins_default: main-uart0-default-pins {
pinctrl-single,pins = <
J722S_IOPAD(0x01c8, PIN_INPUT, 0) /* (F19) UART0_RXD */
J722S_IOPAD(0x01cc, PIN_OUTPUT, 0) /* (F20) UART0_TXD */
>;
bootph-all;
};
main_usbc_power_pins_default: main-usbc-power-default-pins {
pinctrl-single,pins = <
J722S_IOPAD(0x1b4, PIN_INPUT, 7) /* (B20) SPI0_CS0.GPIO1_15 */
>;
};
};
&audio_refclk1 {
assigned-clock-rates = <25000000>;
};
&main_i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&main_i2c0_pins_default>;
clock-frequency = <400000>;
status = "okay";
veml6030: light-sensor@10 {
compatible = "vishay,veml6030";
reg = <0x10>;
vdd-supply = <&vcc_3v3_sw>;
};
};
&main_i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&main_i2c1_pins_default>;
clock-frequency = <100000>;
status = "okay";
audio_codec: audio-codec@18 {
compatible = "ti,tlv320aic3110";
reg = <0x18>;
pinctrl-names = "default";
pinctrl-0 = <&audio_ext_refclk1_pins_default>;
#sound-dai-cells = <0>;
ai31xx-micbias-vg = <2>;
reset-gpios = <&gpio_exp1 7 GPIO_ACTIVE_LOW>;
HPVDD-supply = <&vcc_3v3_aud>;
SPRVDD-supply = <&vcc_speaker>;
SPLVDD-supply = <&vcc_speaker>;
AVDD-supply = <&vcc_3v3_aud>;
IOVDD-supply = <&vcc_3v3_aud>;
DVDD-supply = <&vcc_1v8>;
};
gpio_exp0: gpio@20 {
compatible = "nxp,pcf8574";
reg = <0x20>;
gpio-controller;
#gpio-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&gpio_exp0_int_pins_default>;
interrupt-parent = <&main_gpio0>;
interrupts = <21 IRQ_TYPE_EDGE_FALLING>;
gpio-line-names = "CSI3_STROBE", "CSI3_TRIGGER",
"CSI3_SHUTTER", "CSI3_OE",
"CSI2_STROBE", "CSI2_TRIGGER",
"CSI2_SHUTTER", "CSI2_OE";
};
gpio_exp1: gpio@21 {
compatible = "nxp,pcf8574";
reg = <0x21>;
gpio-controller;
#gpio-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&gpio_exp1_int_pins_default>;
interrupt-parent = <&main_gpio1>;
interrupts = <49 IRQ_TYPE_EDGE_FALLING>;
gpio-line-names = "GPIO0_HDMI_RST", "GPIO1_CAN_nEN",
"GPIO2_LED", "GPIO3_MCU_CAN0_nEN",
"GPIO4_BUT2", "GPIO5_MCU_CAN1_nEN",
"GPIO6_AUDIO_GPIO", "GPIO7_AUDIO_USER_RESET";
};
gpio_exp2: gpio@23 {
compatible = "nxp,pcf8574";
reg = <0x23>;
gpio-controller;
#gpio-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&gpio_exp2_int_pins_default>;
interrupt-parent = <&main_gpio0>;
interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
gpio-line-names = "CSI1_STROBE", "CSI1_TRIGGER",
"CSI1_SHUTTER", "CSI1_OE",
"CSI0_STROBE", "CSI0_TRIGGER",
"CSI0_SHUTTER", "CSI0_OE";
};
current-sensor@40 {
compatible = "ti,ina233";
reg = <0x40>;
shunt-resistor = <18000>;
};
eeprom@51 {
compatible = "atmel,24c02";
reg = <0x51>;
pagesize = <16>;
};
};
&main_mcan0 {
pinctrl-names = "default";
pinctrl-0 = <&main_mcan0_pins_default>;
phys = <&can_tc0>;
status = "okay";
};
&main_uart0 {
pinctrl-names = "default";
pinctrl-0 = <&main_uart0_pins_default>;
bootph-all;
status = "okay";
};
&mcasp0 {
#sound-dai-cells = <0>;
op-mode = <0>; /* MCASP_IIS_MODE */
pinctrl-names = "default";
pinctrl-0 = <&main_mcasp0_pins_default>;
tdm-slots = <2>;
serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
0 0 1 2
0 0 0 0
0 0 0 0
0 0 0 0
>;
status = "okay";
};
&sdhci1 {
/* SD/MMC */
vmmc-supply = <&vcc_3v3_mmc>;
vqmmc-supply = <&vddshv_sdio>;
pinctrl-names = "default";
pinctrl-0 = <&main_mmc1_pins_default>;
disable-wp;
no-1-8-v;
bootph-all;
status = "okay";
};
&serdes_ln_ctrl {
idle-states = <J722S_SERDES0_LANE0_USB>,
<J722S_SERDES1_LANE0_PCIE0_LANE0>;
};
&serdes0 {
status = "okay";
serdes0_usb_link: phy@0 {
reg = <0>;
cdns,num-lanes = <1>;
#phy-cells = <0>;
cdns,phy-type = <PHY_TYPE_USB3>;
resets = <&serdes_wiz0 1>;
};
};
&serdes_wiz0 {
status = "okay";
};
&usbss0 {
ti,vbus-divider;
status = "okay";
};
&usb0 {
dr_mode = "otg";
usb-role-switch;
maximum-speed = "high-speed";
port {
usb0_ep: endpoint {
remote-endpoint = <&usb0_con>;
};
};
};
&usbss1 {
ti,vbus-divider;
status = "okay";
};
&usb1 {
dr_mode = "host";
phys = <&serdes0_usb_link>;
phy-names = "cdns3,usb3-phy";
maximum-speed = "super-speed";
};