// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
 */

/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>

#include "monaco.dtsi"
#include "monaco-pmics.dtsi"
/ {
	model = "Qualcomm Technologies, Inc. QCS8300 Ride";
	compatible = "qcom,qcs8300-ride", "qcom,qcs8300";
	chassis-type = "embedded";

	aliases {
		serial0 = &uart7;
		mmc0 = &sdhc_1;
		serial1 = &uart2;
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	vreg_1p0: regulator-vreg-1p0 {
		compatible = "regulator-fixed";
		regulator-name = "VREG_1P0";

		regulator-min-microvolt = <1000000>;
		regulator-max-microvolt = <1000000>;

		vin-supply = <&vreg_1p8>;

		regulator-always-on;
		regulator-boot-on;
	};

	vreg_1p8: regulator-vreg-1p8 {
		compatible = "regulator-fixed";
		regulator-name = "VREG_1P8";

		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;

		vin-supply = <&vreg_5p0>;

		regulator-always-on;
		regulator-boot-on;
	};

	vreg_3p0: regulator-vreg-3p0 {
		compatible = "regulator-fixed";
		regulator-name = "VREG_3P0";

		regulator-min-microvolt = <3000000>;
		regulator-max-microvolt = <3000000>;

		vin-supply = <&vreg_12p0>;

		regulator-always-on;
		regulator-boot-on;
	};

	vreg_5p0: regulator-vreg-5p0 {
		compatible = "regulator-fixed";
		regulator-name = "VREG_5P0";

		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;

		vin-supply = <&vreg_12p0>;

		regulator-always-on;
		regulator-boot-on;
	};

	vreg_12p0: regulator-vreg-12p0 {
		compatible = "regulator-fixed";
		regulator-name = "VREG_12P0";

		regulator-min-microvolt = <12000000>;
		regulator-max-microvolt = <12000000>;

		regulator-always-on;
		regulator-boot-on;
	};

	dp0-connector {
		compatible = "dp-connector";
		label = "DP0";
		type = "full-size";

		port {
			dp0_connector_in: endpoint {
				remote-endpoint = <&mdss_dp0_out>;
			};
		};
	};

	dp-dsi0-connector {
		compatible = "dp-connector";
		label = "DSI0";
		type = "full-size";

		port {
			dp_dsi0_connector_in: endpoint {
				remote-endpoint = <&dsi2dp_bridge_out>;
			};
		};
	};

	vreg_conn_1p05: regulator-conn-1p05 {
		compatible = "regulator-fixed";
		regulator-name = "vreg_conn_1p05";
		regulator-min-microvolt = <1050000>;
		regulator-max-microvolt = <1050000>;
		vin-supply = <&vreg_conn_1p8>;
	};

	vreg_conn_1p35: regulator-conn-1p35 {
		compatible = "regulator-fixed";
		regulator-name = "vreg_conn_1p35";
		regulator-min-microvolt = <1350000>;
		regulator-max-microvolt = <1350000>;
		vin-supply = <&vreg_conn_1p8>;
	};

	vreg_conn_1p8: regulator-conn-1p8 {
		compatible = "regulator-fixed";
		regulator-name = "vreg_conn_1p8";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		startup-delay-us = <4000>;
		enable-active-high;
		gpio = <&pmm8650au_1_gpios 4 GPIO_ACTIVE_HIGH>;
	};

	vreg_conn_1p95: regulator-conn-1p95 {
		compatible = "regulator-fixed";
		regulator-name = "vreg_conn_1p95";
		regulator-min-microvolt = <1950000>;
		regulator-max-microvolt = <1950000>;
		vin-supply = <&vreg_conn_1p8>;
	};

	vreg_conn_pa: regulator-conn-pa {
		compatible = "regulator-fixed";
		regulator-name = "vreg_conn_pa";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		startup-delay-us = <4000>;
		enable-active-high;
		gpio = <&pmm8650au_1_gpios 6 GPIO_ACTIVE_HIGH>;
	};

	regulator-usb2-vbus {
		compatible = "regulator-fixed";
		regulator-name = "USB2_VBUS";
		gpio = <&pmm8650au_1_gpios 7 GPIO_ACTIVE_HIGH>;
		pinctrl-0 = <&usb2_en>;
		pinctrl-names = "default";
		enable-active-high;
		regulator-always-on;
	};

	wcn6855-pmu {
		compatible = "qcom,wcn6855-pmu";

		pinctrl-0 = <&wlan_en_state>;
		pinctrl-names = "default";

		vddio-supply = <&vreg_conn_pa>;
		vddaon-supply = <&vreg_conn_1p8>;
		vddpmu-supply = <&vreg_conn_pa>;
		vddpmumx-supply = <&vreg_conn_1p8>;
		vddpmucx-supply = <&vreg_conn_pa>;
		/* WLAN rails: 1.05/1.35/1.95V (nominal 0.95/1.30/1.90V) */
		vddrfa0p95-supply = <&vreg_conn_1p05>;
		vddrfa1p3-supply = <&vreg_conn_1p35>;
		vddrfa1p9-supply = <&vreg_conn_1p95>;
		vddpcie1p3-supply = <&vreg_conn_1p35>;
		vddpcie1p9-supply = <&vreg_conn_1p95>;

		bt-enable-gpios = <&tlmm 55 GPIO_ACTIVE_HIGH>;
		wlan-enable-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;

		regulators {
			vreg_pmu_rfa_cmn: ldo0 {
				regulator-name = "vreg_pmu_rfa_cmn";
			};

			vreg_pmu_aon_0p59: ldo1 {
				regulator-name = "vreg_pmu_aon_0p59";
			};

			vreg_pmu_wlcx_0p8: ldo2 {
				regulator-name = "vreg_pmu_wlcx_0p8";
			};

			vreg_pmu_wlmx_0p85: ldo3 {
				regulator-name = "vreg_pmu_wlmx_0p85";
			};

			vreg_pmu_btcmx_0p85: ldo4 {
				regulator-name = "vreg_pmu_btcmx_0p85";
			};

			vreg_pmu_rfa_0p8: ldo5 {
				regulator-name = "vreg_pmu_rfa_0p8";
			};

			vreg_pmu_rfa_1p2: ldo6 {
				regulator-name = "vreg_pmu_rfa_1p2";
			};

			vreg_pmu_rfa_1p7: ldo7 {
				regulator-name = "vreg_pmu_rfa_1p7";
			};

			vreg_pmu_pcie_0p9: ldo8 {
				regulator-name = "vreg_pmu_pcie_0p9";
			};

			vreg_pmu_pcie_1p8: ldo9 {
				regulator-name = "vreg_pmu_pcie_1p8";
			};
		};
	};
};

&apps_rsc {
	regulators-0 {
		compatible = "qcom,pmm8654au-rpmh-regulators";
		qcom,pmic-id = "a";

		vreg_s4a: smps4 {
			regulator-name = "vreg_s4a";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_s9a: smps9 {
			regulator-name = "vreg_s9a";
			regulator-min-microvolt = <1352000>;
			regulator-max-microvolt = <1352000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l3a: ldo3 {
			regulator-name = "vreg_l3a";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l4a: ldo4 {
			regulator-name = "vreg_l4a";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <912000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l5a: ldo5 {
			regulator-name = "vreg_l5a";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l6a: ldo6 {
			regulator-name = "vreg_l6a";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <912000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l7a: ldo7 {
			regulator-name = "vreg_l7a";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <912000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l8a: ldo8 {
			regulator-name = "vreg_l8a";
			regulator-min-microvolt = <2504000>;
			regulator-max-microvolt = <2960000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l9a: ldo9 {
			regulator-name = "vreg_l9a";
			regulator-min-microvolt = <2970000>;
			regulator-max-microvolt = <3072000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};
	};

	regulators-1 {
		compatible = "qcom,pmm8654au-rpmh-regulators";
		qcom,pmic-id = "c";

		vreg_s5c: smps5 {
			regulator-name = "vreg_s5c";
			regulator-min-microvolt = <1104000>;
			regulator-max-microvolt = <1104000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l1c: ldo1 {
			regulator-name = "vreg_l1c";
			regulator-min-microvolt = <300000>;
			regulator-max-microvolt = <500000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l2c: ldo2 {
			regulator-name = "vreg_l2c";
			regulator-min-microvolt = <900000>;
			regulator-max-microvolt = <904000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l4c: ldo4 {
			regulator-name = "vreg_l4c";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l6c: ldo6 {
			regulator-name = "vreg_l6c";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l7c: ldo7 {
			regulator-name = "vreg_l7c";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l8c: ldo8 {
			regulator-name = "vreg_l8c";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l9c: ldo9 {
			regulator-name = "vreg_l9c";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
						   RPMH_REGULATOR_MODE_HPM>;
		};
	};
};

&ethernet0 {
	phy-mode = "2500base-x";
	phy-handle = <&phy0>;

	pinctrl-0 = <&ethernet0_default>;
	pinctrl-names = "default";

	snps,mtl-rx-config = <&mtl_rx_setup>;
	snps,mtl-tx-config = <&mtl_tx_setup>;
	snps,ps-speed = <1000>;

	status = "okay";

	mdio {
		compatible = "snps,dwmac-mdio";
		#address-cells = <1>;
		#size-cells = <0>;

		phy0: phy@8 {
			compatible = "ethernet-phy-id31c3.1c33";
			reg = <0x8>;
			device_type = "ethernet-phy";
			interrupts-extended = <&tlmm 4 IRQ_TYPE_EDGE_FALLING>;
			reset-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
			reset-assert-us = <11000>;
			reset-deassert-us = <70000>;
		};
	};

	mtl_rx_setup: rx-queues-config {
		snps,rx-queues-to-use = <4>;
		snps,rx-sched-sp;

		queue0 {
			snps,dcb-algorithm;
			snps,map-to-dma-channel = <0x0>;
			snps,route-up;
			snps,priority = <0x1>;
		};

		queue1 {
			snps,dcb-algorithm;
			snps,map-to-dma-channel = <0x1>;
			snps,route-ptp;
		};

		queue2 {
			snps,avb-algorithm;
			snps,map-to-dma-channel = <0x2>;
			snps,route-avcp;
		};

		queue3 {
			snps,avb-algorithm;
			snps,map-to-dma-channel = <0x3>;
			snps,priority = <0xc>;
		};
	};

	mtl_tx_setup: tx-queues-config {
		snps,tx-queues-to-use = <4>;

		queue0 {
			snps,dcb-algorithm;
		};

		queue1 {
			snps,dcb-algorithm;
		};

		queue2 {
			snps,avb-algorithm;
			snps,send_slope = <0x1000>;
			snps,idle_slope = <0x1000>;
			snps,high_credit = <0x3e800>;
			snps,low_credit = <0xffc18000>;
		};

		queue3 {
			snps,avb-algorithm;
			snps,send_slope = <0x1000>;
			snps,idle_slope = <0x1000>;
			snps,high_credit = <0x3e800>;
			snps,low_credit = <0xffc18000>;
		};
	};
};

&gpu {
	status = "okay";
};

&gpu_zap_shader {
	firmware-name = "qcom/qcs8300/a623_zap.mbn";
};

&i2c8 {
	clock-frequency = <400000>;

	status = "okay";

	io_expander: gpio@74 {
		compatible = "ti,tca9539";
		reg = <0x74>;
		interrupts-extended = <&tlmm 93 IRQ_TYPE_EDGE_BOTH>;
		gpio-controller;
		#gpio-cells = <2>;
		interrupt-controller;
		#interrupt-cells = <2>;
		reset-gpios = <&tlmm 66 GPIO_ACTIVE_LOW>;

		pinctrl-0 = <&io_expander_intr_active>,
			    <&io_expander_reset_active>;
		pinctrl-names = "default";
	};

	i2c-mux@70 {
		compatible = "nxp,pca9543";
		reg = <0x70>;

		#address-cells = <1>;
		#size-cells = <0>;

		i2c@0 {
			reg = <0>;
			#address-cells = <1>;
			#size-cells = <0>;

			bridge@58 {
				compatible = "analogix,anx7625";
				reg = <0x58>;
				interrupts-extended = <&io_expander 2 IRQ_TYPE_EDGE_FALLING>;
				enable-gpios = <&io_expander 1 GPIO_ACTIVE_HIGH>;
				reset-gpios = <&io_expander 0 GPIO_ACTIVE_HIGH>;
				vdd10-supply = <&vreg_1p0>;
				vdd18-supply = <&vreg_1p8>;
				vdd33-supply = <&vreg_3p0>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;

						dsi2dp_bridge_in: endpoint {

							remote-endpoint = <&mdss_dsi0_out>;
						};
					};

					port@1 {
						reg = <1>;

						dsi2dp_bridge_out: endpoint {

							remote-endpoint = <&dp_dsi0_connector_in>;
						};
					};
				};
			};
		};
	};
};

&pmm8650au_1_gpios {
	usb2_en: usb2-en-state {
		pins = "gpio7";
		function = "normal";
		output-enable;
		power-source = <0>;
	};
};

&iris {
	status = "okay";
};

&mdss {
	status = "okay";
};

&mdss_dp0 {
	pinctrl-0 = <&dp_hot_plug_det>;
	pinctrl-names = "default";

	status = "okay";
};

&mdss_dp0_out {
	data-lanes = <0 1 2 3>;
	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
	remote-endpoint = <&dp0_connector_in>;
};

&mdss_dp0_phy {
	vdda-phy-supply = <&vreg_l5a>;
	vdda-pll-supply = <&vreg_l4a>;

	status = "okay";
};

&pcie0 {
	pinctrl-0 = <&pcie0_default_state>;
	pinctrl-names = "default";

	status = "okay";
};

&pcieport0 {
	reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
	wake-gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;

	wifi@0 {
		compatible = "pci17cb,1103";
		reg = <0x10000 0x0 0x0 0x0 0x0>;

		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
		vddaon-supply = <&vreg_pmu_aon_0p59>;
		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
		vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;

		qcom,calibration-variant = "QC_QCS8300_Ride";
	};
};

&pcie0_phy {
	vdda-phy-supply = <&vreg_l6a>;
	vdda-pll-supply = <&vreg_l5a>;

	status = "okay";
};

&pcie1 {
	pinctrl-0 = <&pcie1_default_state>;
	pinctrl-names = "default";

	status = "okay";
};

&pcieport1 {
	reset-gpios = <&tlmm 23 GPIO_ACTIVE_LOW>;
	wake-gpios = <&tlmm 21 GPIO_ACTIVE_LOW>;
};

&pcie1_phy {
	vdda-phy-supply = <&vreg_l6a>;
	vdda-pll-supply = <&vreg_l5a>;

	status = "okay";
};

&mdss_dsi0 {
	vdda-supply = <&vreg_l5a>;

	status = "okay";
};

&mdss_dsi0_phy {
	vdds-supply = <&vreg_l4a>;

	status = "okay";
};

&mdss_dsi0_out {
	data-lanes = <0 1 2 3>;
	remote-endpoint = <&dsi2dp_bridge_in>;
};

&qupv3_id_0 {
	status = "okay";
};

&qupv3_id_1 {
	status = "okay";
};

&remoteproc_adsp {
	firmware-name = "qcom/qcs8300/adsp.mbn";
	status = "okay";
};

&remoteproc_cdsp {
	firmware-name = "qcom/qcs8300/cdsp0.mbn";
	status = "okay";
};

&remoteproc_gpdsp {
	firmware-name = "qcom/qcs8300/gpdsp0.mbn";
	status = "okay";
};

&serdes0 {
	vdda-0p9-supply = <&vreg_l4a>;
	vdda-1p2-supply = <&vreg_l5a>;

	status = "okay";
};

&sdhc_1 {
	pinctrl-0 = <&sdc1_state_on>;
	pinctrl-1 = <&sdc1_state_off>;
	pinctrl-names = "default", "sleep";

	bus-width = <8>;
	mmc-ddr-1_8v;
	mmc-hs200-1_8v;
	mmc-hs400-1_8v;
	mmc-hs400-enhanced-strobe;
	vmmc-supply = <&vreg_l8a>;
	vqmmc-supply = <&vreg_s4a>;

	non-removable;
	no-sd;
	no-sdio;

	status = "okay";
};

&tlmm {
	bt_en_state: bt-en-state {
		pins = "gpio55";
		function = "gpio";
		bias-pull-down;
	};

	pcie0_default_state: pcie0-default-state {
		wake-pins {
			pins = "gpio0";
			function = "gpio";
			drive-strength = <2>;
			bias-pull-up;
		};

		clkreq-pins {
			pins = "gpio1";
			function = "pcie0_clkreq";
			drive-strength = <2>;
			bias-pull-up;
		};

		perst-pins {
			pins = "gpio2";
			function = "gpio";
			drive-strength = <2>;
			bias-pull-down;
		};
	};

	ethernet0_default: ethernet0-default-state {
		ethernet0_mdc: ethernet0-mdc-pins {
			pins = "gpio5";
			function = "emac0_mdc";
			drive-strength = <16>;
			bias-pull-up;
		};

		ethernet0_mdio: ethernet0-mdio-pins {
			pins = "gpio6";
			function = "emac0_mdio";
			drive-strength = <16>;
			bias-pull-up;
		};
	};

	pcie1_default_state: pcie1-default-state {
		wake-pins {
			pins = "gpio21";
			function = "gpio";
			drive-strength = <2>;
			bias-pull-up;
		};

		clkreq-pins {
			pins = "gpio22";
			function = "pcie1_clkreq";
			drive-strength = <2>;
			bias-pull-up;
		};

		perst-pins {
			pins = "gpio23";
			function = "gpio";
			drive-strength = <2>;
			bias-pull-down;
		};
	};

	io_expander_reset_active: io-expander-reset-active-state {
		pins = "gpio66";
		function = "gpio";
		drive-strength = <2>;
		bias-disable;
	};

	io_expander_intr_active: io-expander-intr-active-state {
		pins = "gpio93";
		function = "gpio";
		drive-strength = <2>;
		bias-disable;
	};

	dp_hot_plug_det: dp-hot-plug-det-state {
		pins = "gpio94";
		function = "edp0_hot";
		bias-disable;
	};

	wlan_en_state: wlan-en-state {
		pins = "gpio54";
		function = "gpio";
		bias-pull-down;
	};
};

&uart2 {
	status = "okay";

	bluetooth: bluetooth {
		compatible = "qcom,wcn6855-bt";
		firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv";
		max-speed = <3200000>;

		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
		vddaon-supply = <&vreg_pmu_aon_0p59>;
		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
		vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
		vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
	};
};

&uart7 {
	status = "okay";
};

&ufs_mem_hc {
	reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
	vcc-supply = <&vreg_l8a>;
	vcc-max-microamp = <1100000>;
	vccq-supply = <&vreg_l4c>;
	vccq-max-microamp = <1200000>;
	status = "okay";
};

&ufs_mem_phy {
	vdda-phy-supply = <&vreg_l4a>;
	vdda-pll-supply = <&vreg_l5a>;
	status = "okay";
};

&usb_1_hsphy {
	vdda-pll-supply = <&vreg_l7a>;
	vdda18-supply = <&vreg_l7c>;
	vdda33-supply = <&vreg_l9a>;

	status = "okay";
};

&usb_2_hsphy {
	vdda-pll-supply = <&vreg_l7a>;
	vdda18-supply = <&vreg_l7c>;
	vdda33-supply = <&vreg_l9a>;

	status = "okay";
};

&usb_qmpphy {
	vdda-phy-supply = <&vreg_l7a>;
	vdda-pll-supply = <&vreg_l5a>;

	status = "okay";
};

&usb_1 {
	dr_mode = "peripheral";

	status = "okay";
};

&usb_2 {
	dr_mode = "host";

	status = "okay";
};