// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2021 Rockchip Electronics Co., Ltd.
*/
#include "rk3588s.dtsi"
#include "rk3588-pinctrl.dtsi"
/ {
pcie30_phy_grf: syscon@fd5b8000 {
compatible = "rockchip,rk3588-pcie3-phy-grf", "syscon";
reg = <0x0 0xfd5b8000 0x0 0x10000>;
};
pipe_phy1_grf: syscon@fd5c0000 {
compatible = "rockchip,rk3588-pipe-phy-grf", "syscon";
reg = <0x0 0xfd5c0000 0x0 0x100>;
};
i2s8_8ch: i2s@fddc8000 {
compatible = "rockchip,rk3588-i2s-tdm";
reg = <0x0 0xfddc8000 0x0 0x1000>;
interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru MCLK_I2S8_8CH_TX>, <&cru MCLK_I2S8_8CH_TX>, <&cru HCLK_I2S8_8CH>;
clock-names = "mclk_tx", "mclk_rx", "hclk";
assigned-clocks = <&cru CLK_I2S8_8CH_TX_SRC>;
assigned-clock-parents = <&cru PLL_AUPLL>;
dmas = <&dmac2 22>;
dma-names = "tx";
power-domains = <&power RK3588_PD_VO0>;
resets = <&cru SRST_M_I2S8_8CH_TX>;
reset-names = "tx-m";
#sound-dai-cells = <0>;
status = "disabled";
};
i2s6_8ch: i2s@fddf4000 {
compatible = "rockchip,rk3588-i2s-tdm";
reg = <0x0 0xfddf4000 0x0 0x1000>;
interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru MCLK_I2S6_8CH_TX>, <&cru MCLK_I2S6_8CH_TX>, <&cru HCLK_I2S6_8CH>;
clock-names = "mclk_tx", "mclk_rx", "hclk";
assigned-clocks = <&cru CLK_I2S6_8CH_TX_SRC>;
assigned-clock-parents = <&cru PLL_AUPLL>;
dmas = <&dmac2 4>;
dma-names = "tx";
power-domains = <&power RK3588_PD_VO1>;
resets = <&cru SRST_M_I2S6_8CH_TX>;
reset-names = "tx-m";
#sound-dai-cells = <0>;
status = "disabled";
};
i2s7_8ch: i2s@fddf8000 {
compatible = "rockchip,rk3588-i2s-tdm";
reg = <0x0 0xfddf8000 0x0 0x1000>;
interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru MCLK_I2S7_8CH_RX>, <&cru MCLK_I2S7_8CH_RX>, <&cru HCLK_I2S7_8CH>;
clock-names = "mclk_tx", "mclk_rx", "hclk";
assigned-clocks = <&cru CLK_I2S7_8CH_RX_SRC>;
assigned-clock-parents = <&cru PLL_AUPLL>;
dmas = <&dmac2 21>;
dma-names = "rx";
power-domains = <&power RK3588_PD_VO1>;
resets = <&cru SRST_M_I2S7_8CH_RX>;
reset-names = "rx-m";
#sound-dai-cells = <0>;
status = "disabled";
};
i2s10_8ch: i2s@fde00000 {
compatible = "rockchip,rk3588-i2s-tdm";
reg = <0x0 0xfde00000 0x0 0x1000>;
interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru MCLK_I2S10_8CH_RX>, <&cru MCLK_I2S10_8CH_RX>, <&cru HCLK_I2S10_8CH>;
clock-names = "mclk_tx", "mclk_rx", "hclk";
assigned-clocks = <&cru CLK_I2S10_8CH_RX_SRC>;
assigned-clock-parents = <&cru PLL_AUPLL>;
dmas = <&dmac2 24>;
dma-names = "rx";
power-domains = <&power RK3588_PD_VO1>;
resets = <&cru SRST_M_I2S10_8CH_RX>;
reset-names = "rx-m";
#sound-dai-cells = <0>;
status = "disabled";
};
pcie3x4: pcie@fe150000 {
compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie";
#address-cells = <3>;
#size-cells = <2>;
bus-range = <0x00 0x0f>;
clocks = <&cru ACLK_PCIE_4L_MSTR>, <&cru ACLK_PCIE_4L_SLV>,
<&cru ACLK_PCIE_4L_DBI>, <&cru PCLK_PCIE_4L>,
<&cru CLK_PCIE_AUX0>, <&cru CLK_PCIE4L_PIPE>;
clock-names = "aclk_mst", "aclk_slv",
"aclk_dbi", "pclk",
"aux", "pipe";
device_type = "pci";
interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH 0>;
interrupt-names = "sys", "pmc", "msg", "legacy", "err";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &pcie3x4_intc 0>,
<0 0 0 2 &pcie3x4_intc 1>,
<0 0 0 3 &pcie3x4_intc 2>,
<0 0 0 4 &pcie3x4_intc 3>;
linux,pci-domain = <0>;
max-link-speed = <3>;
msi-map = <0x0000 &its1 0x0000 0x1000>;
num-lanes = <4>;
phys = <&pcie30phy>;
phy-names = "pcie-phy";
power-domains = <&power RK3588_PD_PCIE>;
ranges = <0x01000000 0x0 0xf0100000 0x0 0xf0100000 0x0 0x00100000>,
<0x02000000 0x0 0xf0200000 0x0 0xf0200000 0x0 0x00e00000>,
<0x03000000 0x0 0x40000000 0x9 0x00000000 0x0 0x40000000>;
reg = <0xa 0x40000000 0x0 0x00400000>,
<0x0 0xfe150000 0x0 0x00010000>,
<0x0 0xf0000000 0x0 0x00100000>;
reg-names = "dbi", "apb", "config";
resets = <&cru SRST_PCIE0_POWER_UP>, <&cru SRST_P_PCIE0>;
reset-names = "pwr", "pipe";
status = "disabled";
pcie3x4_intc: legacy-interrupt-controller {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <1>;
interrupt-parent = <&gic>;
interrupts = <GIC_SPI 260 IRQ_TYPE_EDGE_RISING 0>;
};
};
pcie3x2: pcie@fe160000 {
compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie";
#address-cells = <3>;
#size-cells = <2>;
bus-range = <0x10 0x1f>;
clocks = <&cru ACLK_PCIE_2L_MSTR>, <&cru ACLK_PCIE_2L_SLV>,
<&cru ACLK_PCIE_2L_DBI>, <&cru PCLK_PCIE_2L>,
<&cru CLK_PCIE_AUX1>, <&cru CLK_PCIE2L_PIPE>;
clock-names = "aclk_mst", "aclk_slv",
"aclk_dbi", "pclk",
"aux", "pipe";
device_type = "pci";
interrupts = <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH 0>;
interrupt-names = "sys", "pmc", "msg", "legacy", "err";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &pcie3x2_intc 0>,
<0 0 0 2 &pcie3x2_intc 1>,
<0 0 0 3 &pcie3x2_intc 2>,
<0 0 0 4 &pcie3x2_intc 3>;
linux,pci-domain = <1>;
max-link-speed = <3>;
msi-map = <0x1000 &its1 0x1000 0x1000>;
num-lanes = <2>;
phys = <&pcie30phy>;
phy-names = "pcie-phy";
power-domains = <&power RK3588_PD_PCIE>;
ranges = <0x01000000 0x0 0xf1100000 0x0 0xf1100000 0x0 0x00100000>,
<0x02000000 0x0 0xf1200000 0x0 0xf1200000 0x0 0x00e00000>,
<0x03000000 0x0 0x40000000 0x9 0x40000000 0x0 0x40000000>;
reg = <0xa 0x40400000 0x0 0x00400000>,
<0x0 0xfe160000 0x0 0x00010000>,
<0x0 0xf1000000 0x0 0x00100000>;
reg-names = "dbi", "apb", "config";
resets = <&cru SRST_PCIE1_POWER_UP>, <&cru SRST_P_PCIE1>;
reset-names = "pwr", "pipe";
status = "disabled";
pcie3x2_intc: legacy-interrupt-controller {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <1>;
interrupt-parent = <&gic>;
interrupts = <GIC_SPI 255 IRQ_TYPE_EDGE_RISING 0>;
};
};
pcie2x1l0: pcie@fe170000 {
compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie";
bus-range = <0x20 0x2f>;
clocks = <&cru ACLK_PCIE_1L0_MSTR>, <&cru ACLK_PCIE_1L0_SLV>,
<&cru ACLK_PCIE_1L0_DBI>, <&cru PCLK_PCIE_1L0>,
<&cru CLK_PCIE_AUX2>, <&cru CLK_PCIE1L0_PIPE>;
clock-names = "aclk_mst", "aclk_slv",
"aclk_dbi", "pclk",
"aux", "pipe";
device_type = "pci";
interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH 0>;
interrupt-names = "sys", "pmc", "msg", "legacy", "err";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &pcie2x1l0_intc 0>,
<0 0 0 2 &pcie2x1l0_intc 1>,
<0 0 0 3 &pcie2x1l0_intc 2>,
<0 0 0 4 &pcie2x1l0_intc 3>;
linux,pci-domain = <2>;
max-link-speed = <2>;
msi-map = <0x2000 &its0 0x2000 0x1000>;
num-lanes = <1>;
phys = <&combphy1_ps PHY_TYPE_PCIE>;
phy-names = "pcie-phy";
power-domains = <&power RK3588_PD_PCIE>;
ranges = <0x01000000 0x0 0xf2100000 0x0 0xf2100000 0x0 0x00100000>,
<0x02000000 0x0 0xf2200000 0x0 0xf2200000 0x0 0x00e00000>,
<0x03000000 0x0 0x40000000 0x9 0x80000000 0x0 0x40000000>;
reg = <0xa 0x40800000 0x0 0x00400000>,
<0x0 0xfe170000 0x0 0x00010000>,
<0x0 0xf2000000 0x0 0x00100000>;
reg-names = "dbi", "apb", "config";
resets = <&cru SRST_PCIE2_POWER_UP>, <&cru SRST_P_PCIE2>;
reset-names = "pwr", "pipe";
#address-cells = <3>;
#size-cells = <2>;
status = "disabled";
pcie2x1l0_intc: legacy-interrupt-controller {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <1>;
interrupt-parent = <&gic>;
interrupts = <GIC_SPI 240 IRQ_TYPE_EDGE_RISING 0>;
};
};
gmac0: ethernet@fe1b0000 {
compatible = "rockchip,rk3588-gmac", "snps,dwmac-4.20a";
reg = <0x0 0xfe1b0000 0x0 0x10000>;
interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH 0>,
<GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH 0>;
interrupt-names = "macirq", "eth_wake_irq";
clocks = <&cru CLK_GMAC_125M>, <&cru CLK_GMAC_50M>,
<&cru PCLK_GMAC0>, <&cru ACLK_GMAC0>,
<&cru CLK_GMAC0_PTP_REF>;
clock-names = "stmmaceth", "clk_mac_ref",
"pclk_mac", "aclk_mac",
"ptp_ref";
power-domains = <&power RK3588_PD_GMAC>;
resets = <&cru SRST_A_GMAC0>;
reset-names = "stmmaceth";
rockchip,grf = <&sys_grf>;
rockchip,php-grf = <&php_grf>;
snps,axi-config = <&gmac0_stmmac_axi_setup>;
snps,mixed-burst;
snps,mtl-rx-config = <&gmac0_mtl_rx_setup>;
snps,mtl-tx-config = <&gmac0_mtl_tx_setup>;
snps,tso;
status = "disabled";
mdio0: mdio {
compatible = "snps,dwmac-mdio";
#address-cells = <0x1>;
#size-cells = <0x0>;
};
gmac0_stmmac_axi_setup: stmmac-axi-config {
snps,blen = <0 0 0 0 16 8 4>;
snps,wr_osr_lmt = <4>;
snps,rd_osr_lmt = <8>;
};
gmac0_mtl_rx_setup: rx-queues-config {
snps,rx-queues-to-use = <2>;
queue0 {};
queue1 {};
};
gmac0_mtl_tx_setup: tx-queues-config {
snps,tx-queues-to-use = <2>;
queue0 {};
queue1 {};
};
};
sata1: sata@fe220000 {
compatible = "rockchip,rk3588-dwc-ahci", "snps,dwc-ahci";
reg = <0 0xfe220000 0 0x1000>;
interrupts = <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru ACLK_SATA1>, <&cru CLK_PMALIVE1>,
<&cru CLK_RXOOB1>, <&cru CLK_PIPEPHY1_REF>,
<&cru CLK_PIPEPHY1_PIPE_ASIC_G>;
clock-names = "sata", "pmalive", "rxoob", "ref", "asic";
ports-implemented = <0x1>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
sata-port@0 {
reg = <0>;
hba-port-cap = <HBA_PORT_FBSCP>;
phys = <&combphy1_ps PHY_TYPE_SATA>;
phy-names = "sata-phy";
snps,rx-ts-max = <32>;
snps,tx-ts-max = <32>;
};
};
combphy1_ps: phy@fee10000 {
compatible = "rockchip,rk3588-naneng-combphy";
reg = <0x0 0xfee10000 0x0 0x100>;
clocks = <&cru CLK_REF_PIPE_PHY1>, <&cru PCLK_PCIE_COMBO_PIPE_PHY1>,
<&cru PCLK_PHP_ROOT>;
clock-names = "ref", "apb", "pipe";
assigned-clocks = <&cru CLK_REF_PIPE_PHY1>;
assigned-clock-rates = <100000000>;
#phy-cells = <1>;
resets = <&cru SRST_REF_PIPE_PHY1>, <&cru SRST_P_PCIE2_PHY1>;
reset-names = "phy", "apb";
rockchip,pipe-grf = <&php_grf>;
rockchip,pipe-phy-grf = <&pipe_phy1_grf>;
status = "disabled";
};
pcie30phy: phy@fee80000 {
compatible = "rockchip,rk3588-pcie3-phy";
reg = <0x0 0xfee80000 0x0 0x20000>;
#phy-cells = <0>;
clocks = <&cru PCLK_PCIE_COMBO_PIPE_PHY>;
clock-names = "pclk";
resets = <&cru SRST_PCIE30_PHY>;
reset-names = "phy";
rockchip,pipe-grf = <&php_grf>;
rockchip,phy-grf = <&pcie30_phy_grf>;
status = "disabled";
};
};