// SPDX-License-Identifier: BSD-3-Clause /* * Copyright (c) 2022, Konrad Dybcio <konrad.dybcio@somainline.org> * Copyright (c) 2022, Linaro Limited */ /dts-v1/; #include "sm8450-sony-xperia-nagara.dtsi" / { model = "Sony Xperia 5 IV"; compatible = "sony,pdx224", "qcom,sm8450"; imx563_vdig_regulator: imx563-vdig-regulator { compatible = "regulator-fixed"; regulator-name = "imx563_vdig_regulator"; gpio = <&tlmm 22 GPIO_ACTIVE_HIGH>; enable-active-high; pinctrl-names = "default"; pinctrl-0 = <&uwidec_pwr_en>; }; }; &pm8350b_gpios { gpio-line-names = "CAM_PWR_A_CS", /* GPIO_1 */ "NC", "NC", "NC", "SNAPSHOT_N", "NC", "NC", "FOCUS_N"; }; &pm8350c_gpios { gpio-line-names = "FL_STROBE_TRIG_WIDE", /* GPIO_1 */ "FL_STROBE_TRIG_TELE", "WLC_ID", "WLC_TXPWR_EN", "NC", "NC", /* RGBCIR uses a PMIC vreg, so it's most likely NC. */ "NC", "NC", "WIDEC_PWR_EN"; }; &tlmm { gpio-line-names = "TELE_SPI_MISO", /* GPIO_0 */ "TELE_SPI_MOSI", /* SONY says NC, but it only makes sense this way.. */ "TELE_SPI_CLK", "TELE_SPI_CS_N", "WLC_I2C_SDA", "WLC_I2C_SCL", "NC", "PM8010_1_RESET_N", "WLC_INT_N", "NC", "NC", /* GPIO_10 */ "NC", "DISP_ERR_FG", "HALL_INT_N", "ALS_PROX_INT_N", "IMU1_INT", "TS_I2C_SDA", "TS_I2C_SCL", "DISP_RESET_N", "DISP_VDDR_EN", "TS_RESET_N", /* GPIO_20 */ "TS_INT_N", "UWIDEC_PWR_EN", "TELEC_PWR_EN", "CAM1_RESET_N", "LEO_CAM0_RESET_N", "DEBUG_UART_TX", "DEBUG_UART_RX", "FP_SPI_MISO", "FP_SPI_MOSI", "FP_SPI_CLK", /* GPIO_30 */ "FP_SPI_CS_N", "NFC_I2C_SDA", "NFC_I2C_SCL", "NFC_EN", "NFC_CLK_REQ", "NFC_ESE_SPI_MISO", "NFC_ESE_SPI_MOSI", "NFC_ESE_SPI_CLK", "NFC_ESE_SPI_CS", "FP_INT_N", /* GPIO_40 */ "NC", "FP_RESET_N", "WCD_RST_N", "NC", "NFC_DWL_REQ", "NFC_IRQ", "FORCE_USB_BOOT", "APPS_I2C_1_SDA", "APPS_I2C_1_SCL", "SBU_SW_OE", /* GPIO_50 */ "SBU_SW_SEL", "SPK_AMP_I2C_SDA", "SPK_AMP_I2C_SCL", "NC", "NC", "CAMSENSOR_I2C_SDA", "CAMSENSOR_I2C_SCL", "GNSS_ELNA_EN0", "NC", "NC", /* GPIO_60 */ "NC", "NC", "NC", "NC", "NC", "RGBC_IR_INT", "NC", "NC", "NC", "NC", /* GPIO_70 */ "NC", "HAP_I2C_SDA", "HAP_I2C_SCL", "HAP_RST_N", "HAP_INT_N", "HST_BT_UART_CTS", "HST_BT_UART_RFR", "HST_BT_UART_TX", "HST_BT_UART_RX", "HST_WLAN_EN", /* GPIO_80 */ "HST_BT_EN", "HST_SW_CTRL", "NC", "NC", "NC", "DISP_VSYNC", "NC", "NC", "HW_ID_0", "HW_ID_1", /* GPIO_90 */ "USB_CC_DIR", "TRAY_DET", "SW_SERVICE", "PCIE0_RESET_N", "PCIE0_CLK_REQ_N", "PCIE0_WAKE_N", "OIS_ENABLE_WIDE", "DEBUG_GPIO0", "NC", "CAM_MCLK0", /* GPIO_100 */ "CAM_MCLK1", "CAM_MCLK2", "CAM_MCLK3", "NC", "NC", "NC", /* SONY didn't rename this, but there's no ToF so it's likely NC */ "CAM_SOF", "NC", "AFEXPTMG_TELE", "CCI_I2C0_SDA", /* GPIO_110 */ "CCI_I2C0_SCL", "CCI_I2C1_SDA", "CCI_I2C1_SCL", "CCI_I2C2_SDA", "CCI_I2C2_SCL", "NC", "CAM2_RESET_N", "NC", "EXT_VD0_XVS", "CAM3_RESET_N", /* GPIO_120 */ "NC", "NC", "NC", "NC", "RF_ID_EXTENSION_2", "HAP_I2S_CLK", "HAP_I2S_DOUT", "HAP_TRG1", "HAP_I2S_SYNC", "UIM1_DATA", /* GPIO_130 */ "UIM1_CLK", "UIM1_RESET", "TRAY_DET", "UIM2_DATA", "UIM2_CLK", "UIM2_RESET", "UIM2_PRESENT", "SM_RFFE0_CLK", "SM_RFFE0_DATA", "SM_RFFE1_CLK", /* GPIO_140 */ "SM_RFFE1_DATA", "SM_MSS_GRFC4", "HST_AS_EN", "LAA_RX_EN", "NC", "SM_RFFE4_CLK", "SM_RFFE4_DATA", "WLAN_COEX_UART1_RX", "WLAN_COEX_UART1_TX", "RF_LCD_ID_EN", /* GPIO_150 */ "RF_ID_EXTENSION", "SM_MSS_GRFC12", "NFC_COLD_RST", "NC", "NC", "SDR1_QLINK0_REQ", "SDR1_QLINK0_EN", "SDR1_QLINK0_WMSS_RESET_N", "NC", "NC", /* GPIO_160 */ "NC", "SDR2_QLINK2_REQ", "SDR2_QLINK2_EN", "SDR2_QLINK2_WMSS_RESET_N", "WCD_SWR_TX_CLK", "WCD_SWR_TX_DATA0", "WCD_SWR_TX_DATA1", "WCD_SWR_RX_CLK", "WCD_SWR_RX_DATA0", "WCD_SWR_RX_DATA1", /* GPIO_170 */ "SM_DMIC1_CLK", "SM_DMIC1_DATA", "SM_DMIC2_CLK", "SM_DMIC2_DATA", "SPK_AMP_I2S_CLK", "SPK_AMP_I2S_WS", "NC", "NC", "WCD_SWR_TX_DATA2", "SPK_AMP_I2S_ASP_DIN", /* GPIO_180 */ "SPK_AMP_I2S_ASP_DOUT", "SPK_AMP_INT_N", "SPK_AMP_RESET_N", "HST_BT_WLAN_SLIMBUS_CLK", "HST_BT_WLAN_SLIMBUS_DAT0", "NC", "NC", "NC", "NC", "MAG_I2C_SDA", /* GPIO_190 */ "MAG_I2C_SCL", "IMU_SPI_MISO", "IMU_SPI_MOSI", "IMU_SPI_CLK", "IMU_SPI_CS_N", "SENSOR_I2C_SDA", "SENSOR_I2C_SCL", "OIS_TELE_I2C_SDA", "OIS_TELE_I2C_SCL", "NC", /* GPIO_200 */ "OIS_ENABLE_TELE", "HST_BLE_UART_TX", "HST_BLE_UART_RX", "HSTP_CLK_CFG_SEL", "NC", "APPS_I2C_0_SDA", "APPS_I2C_0_SCL", "CCI_I2C3_SDA", "CCI_I2C3_SCL"; uwidec_pwr_en: uwidec-pwr-en-state { pins = "gpio22"; function = "gpio"; drive-strength = <2>; bias-disable; output-low; }; };