# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
%YAML 1.2
---
$id: http://devicetree.org/schemas/pci/nvidia,tegra20-pcie.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: NVIDIA Tegra PCIe controller
maintainers:
- Thierry Reding <thierry.reding@gmail.com>
- Jon Hunter <jonathanh@nvidia.com>
properties:
compatible:
oneOf:
- enum:
- nvidia,tegra20-pcie
- nvidia,tegra30-pcie
- nvidia,tegra124-pcie
- nvidia,tegra210-pcie
- nvidia,tegra186-pcie
- items:
- const: nvidia,tegra132-pcie
- const: nvidia,tegra124-pcie
reg:
items:
- description: PADS registers
- description: AFI registers
- description: configuration space region
reg-names:
items:
- const: pads
- const: afi
- const: cs
interrupts:
items:
- description: PCIe controller interrupt
- description: MSI controller interrupt
interrupt-names:
items:
- const: intr
- const: msi
clocks:
items:
- description: PCI controller clock
- description: AFI interface clock
- description: reference PLL clock
- description: CML clock
minItems: 3
clock-names:
items:
- const: pex
- const: afi
- const: pll_e
- const: cml
minItems: 3
resets:
items:
- description: AFI interface reset
- description: PCI controller reset
- description: PCI bus reset
reset-names:
items:
- const: pex
- const: afi
- const: pcie_x
interconnects:
items:
- description: AFI memory read client
- description: AFI memory write client
interconnect-names:
items:
- const: dma-mem # read
- const: write
iommus:
maxItems: 1
operating-points-v2:
$ref: /schemas/types.yaml#/definitions/phandle
power-domains:
items:
- description: phandle to the core power domain
pinctrl-names:
items:
# active state, puts PCIe I/O out of deep power down state
- const: default
# puts PCIe I/O into deep power down state
- const: idle
patternProperties:
"^pci@1?[0-9a-f](,[0-7])?$":
description: Root ports are defined as subnodes of the PCIe controller
node.
Note that devices on the PCI bus are dynamically discovered using PCI's
bus enumeration and therefore don't need corresponding device nodes in
DT. However if a device on the PCI bus provides a non-probeable bus such
as I2C or SPI, device nodes need to be added in order to allow the bus'
children to be instantiated at the proper location in the operating
system's device tree (as illustrated by the optional nodes in the
examples below).
$ref: /schemas/pci/pci-pci-bridge.yaml#
unevaluatedProperties: false
properties:
nvidia,num-lanes:
$ref: /schemas/types.yaml#/definitions/uint32
description: |
Number of lanes to use for this port. Valid combinations
are:
- Root port 0 uses 4 lanes, root port 1 is unused.
- Both root ports use 2 lanes.
enum: [ 0, 1, 2, 4 ]
phys:
description: Must contain an phandle to a PHY for each entry in
phy-names.
minItems: 1
maxItems: 4
phy-names:
description: Must include an entry for each active lane. Note that the
number of entries does not have to (though usually will) be equal to
the specified number of lanes in the nvidia,num-lanes property.
Entries are of the form "pcie-N", where N ranges from 0 to the value
specified in nvidia,num-lanes.
items:
enum:
- pcie-0
- pcie-1
- pcie-2
- pcie-3
minItems: 1
maxItems: 4
required:
- reg
- reg-names
- interrupts
- interrupt-names
- clocks
- clock-names
- resets
- reset-names
unevaluatedProperties: false
allOf:
- $ref: /schemas/pinctrl/pinctrl-consumer.yaml#
- $ref: /schemas/pci/pci-host-bridge.yaml#
- $ref: pci-iommu.yaml#
- if:
properties:
compatible:
contains:
const: nvidia,tegra20-pcie
then:
properties:
clocks:
maxItems: 3
clock-names:
maxItems: 3
avdd-pex-supply:
description: Power supply for analog PCIe logic. Must supply 1.05 V.
vdd-pex-supply:
description: Power supply for digital PCIe I/O. Must supply 1.05 V.
avdd-pex-pll-supply:
description: Power supply for dedicated (internal) PCIe PLL. Must
supply 1.05 V.
avdd-plle-supply:
description: Power supply for PLLE, which is shared with SATA. Must
supply 1.05 V.
vddio-pex-clk-supply:
description: Power supply for PCIe clock. Must supply 3.3 V.
required:
- avdd-pex-supply
- vdd-pex-supply
- avdd-pex-pll-supply
- avdd-plle-supply
- vddio-pex-clk-supply
- if:
properties:
compatible:
contains:
const: nvidia,tegra30-pcie
then:
properties:
avdd-pex-pll-supply:
description: Power supply for dedicated (internal) PCIe PLL. Must
supply 1.05 V.
avdd-plle-supply:
description: Power supply for PLLE, which is shared with SATA. Must
supply 1.05 V.
vddio-pex-ctl-supply:
description: Power supply for PCIe control I/O partition. Must
supply 1.8 V.
hvdd-pex-supply:
description: High-voltage supply for PCIe I/O and PCIe output
clocks. Must supply 3.3 V.
avdd-pexa-supply:
description: Power supply for analog PCIe logic. Must supply 1.05 V.
Required if lanes 0 through 3 are used.
vdd-pexa-supply:
description: Power supply for digital PCIe I/O. Must supply 1.05 V.
Required if lanes 0 through 3 are used.
avdd-pexb-supply:
description: Power supply for analog PCIe logic. Must supply 1.05 V.
Required if lanes 4 and 5 are used.
vdd-pexb-supply:
description: Power supply for digital PCIe I/O. Must supply 1.05 V.
Required if lanes 4 and 5 are used.
required:
- avdd-pex-pll-supply
- avdd-plle-supply
- vddio-pex-ctl-supply
- hvdd-pex-supply
- if:
properties:
compatible:
contains:
const: nvidia,tegra124-pcie
then:
properties:
phys:
minItems: 1
maxItems: 1
deprecated: true
phy-names:
items:
- const: pcie
deprecated: true
avddio-pex-supply:
description: Power supply for analog PCIe logic. Must supply 1.05 V.
dvddio-pex-supply:
description: Power supply for digital PCIe I/O. Must supply 1.05 V.
hvdd-pex-supply:
description: High-voltage supply for PCIe I/O and PCIe output
clocks. Must supply 3.3 V.
vddio-pex-ctl-supply:
description: Power supply for PCIe control I/O partition. Must
supply 2.8-3.3 V.
avdd-pex-pll-supply:
deprecated: true
hvdd-pex-pll-e-supply:
deprecated: true
avdd-pll-erefe-supply:
deprecated: true
required:
- avddio-pex-supply
- dvddio-pex-supply
- hvdd-pex-supply
- vddio-pex-ctl-supply
- if:
properties:
compatible:
contains:
const: nvidia,tegra210-pcie
then:
properties:
hvddio-pex-supply:
description: High-voltage supply for PCIe I/O and PCIe output
clocks. Must supply 1.8 V.
dvddio-pex-supply:
description: Power supply for digital PCIe I/O. Must supply 1.05 V.
vddio-pex-ctl-supply:
description: Power supply for PCIe control I/O partition. Must
supply 1.8 V.
avdd-pll-uerefe-supply:
deprecated: true
dvdd-pex-pll-supply:
deprecated: true
hvdd-pex-pll-e-supply:
deprecated: true
required:
- hvddio-pex-supply
- dvddio-pex-supply
- vddio-pex-ctl-supply
- if:
properties:
compatible:
contains:
const: nvidia,tegra186-pcie
then:
properties:
clocks:
maxItems: 3
clock-names:
maxItems: 3
power-domains:
description: To ungate power partition by BPMP powergate driver.
Must contain BPMP phandle and PCIe power partition ID.
dvdd-pex-supply:
description: Power supply for digital PCIe I/O. Must supply 1.05 V.
hvdd-pex-pll-supply:
description: High-voltage supply for PLLE (shared with USB3). Must
supply 1.8 V.
hvdd-pex-supply:
description: High-voltage supply for PCIe I/O and PCIe output
clocks. Must supply 1.8 V.
vddio-pexctl-aud-supply:
description: Power supply for PCIe side band signals. Must supply
1.8 V.
required:
- dvdd-pex-supply
- hvdd-pex-pll-supply
- hvdd-pex-supply
- vddio-pexctl-aud-supply
examples:
# Tegra20
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
pcie@80003000 {
compatible = "nvidia,tegra20-pcie";
device_type = "pci";
reg = <0x80003000 0x00000800>, /* PADS registers */
<0x80003800 0x00000200>, /* AFI registers */
<0x90000000 0x10000000>; /* configuration space */
reg-names = "pads", "afi", "cs";
interrupts = <0 98 0x04>, /* controller interrupt */
<0 99 0x04>; /* MSI interrupt */
interrupt-names = "intr", "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
bus-range = <0x00 0xff>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x02000000 0 0x80000000 0x80000000 0 0x00001000>, /* port 0 registers */
<0x02000000 0 0x80001000 0x80001000 0 0x00001000>, /* port 1 registers */
<0x01000000 0 0 0x82000000 0 0x00010000>, /* downstream I/O */
<0x02000000 0 0xa0000000 0xa0000000 0 0x10000000>, /* non-prefetchable memory */
<0x42000000 0 0xb0000000 0xb0000000 0 0x10000000>; /* prefetchable memory */
clocks = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 118>;
clock-names = "pex", "afi", "pll_e";
resets = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 74>;
reset-names = "pex", "afi", "pcie_x";
avdd-pex-supply = <&pci_vdd_reg>;
vdd-pex-supply = <&pci_vdd_reg>;
avdd-pex-pll-supply = <&pci_vdd_reg>;
avdd-plle-supply = <&pci_vdd_reg>;
vddio-pex-clk-supply = <&pci_clk_reg>;
/* root port 00:01.0 */
pci@1,0 {
device_type = "pci";
assigned-addresses = <0x82000800 0 0x80000000 0 0x1000>;
reg = <0x000800 0 0 0 0>;
bus-range = <0x00 0xff>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
nvidia,num-lanes = <2>;
/* bridge 01:00.0 (optional) */
pci@0,0 {
reg = <0x010000 0 0 0 0>;
bus-range = <0x00 0xff>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
device_type = "pci";
/* endpoint 02:00.0 */
ethernet@0,0 {
reg = <0x020000 0 0 0 0>;
};
};
};
pci@2,0 {
device_type = "pci";
assigned-addresses = <0x82001000 0 0x80001000 0 0x1000>;
reg = <0x001000 0 0 0 0>;
bus-range = <0x00 0xff>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
nvidia,num-lanes = <2>;
};
};
# Tegra210
- |
#include <dt-bindings/clock/tegra210-car.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
pcie@1003000 {
compatible = "nvidia,tegra210-pcie";
device_type = "pci";
reg = <0x01003000 0x00000800>, /* PADS registers */
<0x01003800 0x00000800>, /* AFI registers */
<0x02000000 0x10000000>; /* configuration space */
reg-names = "pads", "afi", "cs";
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
interrupt-names = "intr", "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
bus-range = <0x00 0xff>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x02000000 0 0x01000000 0x01000000 0 0x00001000>, /* port 0 configuration space */
<0x02000000 0 0x01001000 0x01001000 0 0x00001000>, /* port 1 configuration space */
<0x01000000 0 0x0 0x12000000 0 0x00010000>, /* downstream I/O (64 KiB) */
<0x02000000 0 0x13000000 0x13000000 0 0x0d000000>, /* non-prefetchable memory (208 MiB) */
<0x42000000 0 0x20000000 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */
clocks = <&tegra_car TEGRA210_CLK_PCIE>,
<&tegra_car TEGRA210_CLK_AFI>,
<&tegra_car TEGRA210_CLK_PLL_E>,
<&tegra_car TEGRA210_CLK_CML0>;
clock-names = "pex", "afi", "pll_e", "cml";
resets = <&tegra_car 70>,
<&tegra_car 72>,
<&tegra_car 74>;
reset-names = "pex", "afi", "pcie_x";
avdd-pll-uerefe-supply = <&avdd_1v05_pll>;
hvddio-pex-supply = <&vdd_1v8>;
dvddio-pex-supply = <&vdd_pex_1v05>;
dvdd-pex-pll-supply = <&vdd_pex_1v05>;
hvdd-pex-pll-e-supply = <&vdd_1v8>;
vddio-pex-ctl-supply = <&vdd_1v8>;
pci@1,0 {
device_type = "pci";
assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>;
reg = <0x000800 0 0 0 0>;
bus-range = <0x00 0xff>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
nvidia,num-lanes = <4>;
phys = <&phy_pcie0>, <&phy_pcie1>, <&phy_pcie2>, <&phy_pcie3>;
phy-names = "pcie-0", "pcie-1", "pcie-2", "pcie-3";
};
pci@2,0 {
device_type = "pci";
assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>;
reg = <0x001000 0 0 0 0>;
bus-range = <0x00 0xff>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
nvidia,num-lanes = <1>;
phys = <&phy_pcie4>;
phy-names = "pcie-0";
};
};