// SPDX-License-Identifier: GPL-2.0-or-later
/*
* at91sam9m10g45ek.dts - Device Tree file for AT91SAM9M10G45-EK board
*
* Copyright (C) 2011 Atmel,
* 2011 Nicolas Ferre <nicolas.ferre@atmel.com>
*/
/dts-v1/;
#include "at91sam9g45.dtsi"
#include <dt-bindings/pwm/pwm.h>
/ {
model = "Atmel AT91SAM9M10G45-EK";
compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9";
chosen {
bootargs = "mem=64M root=/dev/mtdblock1 rw rootfstype=jffs2";
stdout-path = "serial0:115200n8";
};
memory@70000000 {
reg = <0x70000000 0x4000000>;
};
clocks {
slow_xtal {
clock-frequency = <32768>;
};
main_xtal {
clock-frequency = <12000000>;
};
};
ahb {
apb {
dbgu: serial@ffffee00 {
status = "okay";
};
tcb0: timer@fff7c000 {
timer@0 {
compatible = "atmel,tcb-timer";
reg = <0>, <1>;
};
timer@2 {
compatible = "atmel,tcb-timer";
reg = <2>;
};
};
usart1: serial@fff90000 {
pinctrl-0 =
<&pinctrl_usart1
&pinctrl_usart1_rts
&pinctrl_usart1_cts>;
status = "okay";
};
macb0: ethernet@fffbc000 {
phy-mode = "rmii";
status = "okay";
};
i2c0: i2c@fff84000 {
status = "okay";
ov2640: camera@30 {
compatible = "ovti,ov2640";
reg = <0x30>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
resetb-gpios = <&pioD 12 GPIO_ACTIVE_LOW>;
pwdn-gpios = <&pioD 13 GPIO_ACTIVE_HIGH>;
clocks = <&pmc PMC_TYPE_SYSTEM 9>;
clock-names = "xvclk";
assigned-clocks = <&pmc PMC_TYPE_SYSTEM 9>;
assigned-clock-rates = <25000000>;
port {
ov2640_0: endpoint {
remote-endpoint = <&isi_0>;
bus-width = <8>;
};
};
};
};
i2c1: i2c@fff88000 {
status = "okay";
};
watchdog@fffffd40 {
status = "okay";
};
mmc0: mmc@fff80000 {
pinctrl-0 = <
&pinctrl_board_mmc0
&pinctrl_mmc0_slot0_clk_cmd_dat0
&pinctrl_mmc0_slot0_dat1_3>;
pinctrl-names = "default";
status = "okay";
slot@0 {
reg = <0>;
bus-width = <4>;
cd-gpios = <&pioD 10 GPIO_ACTIVE_HIGH>;
};
};
mmc1: mmc@fffd0000 {
pinctrl-0 = <
&pinctrl_board_mmc1
&pinctrl_mmc1_slot0_clk_cmd_dat0
&pinctrl_mmc1_slot0_dat1_3>;
pinctrl-names = "default";
status = "okay";
slot@0 {
reg = <0>;
bus-width = <4>;
cd-gpios = <&pioD 11 GPIO_ACTIVE_HIGH>;
wp-gpios = <&pioD 29 GPIO_ACTIVE_HIGH>;
};
};
pinctrl@fffff200 {
camera_sensor {
pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
atmel,pins =
<AT91_PIOB 31 AT91_PERIPH_B AT91_PINCTRL_NONE>;
};
pinctrl_sensor_reset: sensor_reset-0 {
atmel,pins =
<AT91_PIOD 12 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
};
pinctrl_sensor_power: sensor_power-0 {
atmel,pins =
<AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
};
};
mmc0 {
pinctrl_board_mmc0: mmc0-board {
atmel,pins =
<AT91_PIOD 10 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD10 gpio CD pin pull up and deglitch */
};
};
mmc1 {
pinctrl_board_mmc1: mmc1-board {
atmel,pins =
<AT91_PIOD 11 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH /* PD11 gpio CD pin pull up and deglitch */
AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; /* PD29 gpio WP pin pull up */
};
};
pwm0 {
pinctrl_pwm_leds: pwm-led {
atmel,pins =
<AT91_PIOD 0 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PD0 periph B */
AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PD31 periph B */
};
};
};
spi0: spi@fffa4000 {
status = "okay";
cs-gpios = <&pioB 3 0>, <0>, <0>, <0>;
flash@0 {
compatible = "atmel,at45", "atmel,dataflash";
spi-max-frequency = <13000000>;
reg = <0>;
};
};
usb2: gadget@fff78000 {
atmel,vbus-gpio = <&pioB 19 GPIO_ACTIVE_HIGH>;
status = "okay";
};
ac97: sound@fffac000 {
status = "okay";
};
adc0: adc@fffb0000 {
pinctrl-names = "default";
pinctrl-0 = <
&pinctrl_adc0_ad0
&pinctrl_adc0_ad1
&pinctrl_adc0_ad2
&pinctrl_adc0_ad3
&pinctrl_adc0_ad4
&pinctrl_adc0_ad5
&pinctrl_adc0_ad6
&pinctrl_adc0_ad7>;
atmel,adc-ts-wires = <4>;
status = "okay";
};
isi@fffb4000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_isi_data_0_7>;
status = "okay";
port {
isi_0: endpoint {
remote-endpoint = <&ov2640_0>;
bus-width = <8>;
vsync-active = <1>;
hsync-active = <1>;
};
};
};
pwm0: pwm@fffb8000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm_leds>;
};
rtc@fffffd20 {
atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
status = "okay";
};
gpbr: syscon@fffffd60 {
status = "okay";
};
rtc@fffffdb0 {
status = "okay";
};
};
fb0: fb@500000 {
display = <&display0>;
status = "okay";
display0: panel {
bits-per-pixel = <32>;
atmel,lcdcon-backlight;
atmel,dmacon = <0x1>;
atmel,lcdcon2 = <0x80008002>;
atmel,guard-time = <9>;
atmel,lcd-wiring-mode = "RGB";
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <9000000>;
hactive = <480>;
vactive = <272>;
hback-porch = <1>;
hfront-porch = <1>;
vback-porch = <40>;
vfront-porch = <1>;
hsync-len = <45>;
vsync-len = <1>;
};
};
};
};
ebi: ebi@10000000 {
status = "okay";
nand_controller: nand-controller {
status = "okay";
pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
pinctrl-names = "default";
nand@3 {
reg = <0x3 0x0 0x800000>;
rb-gpios = <&pioC 8 GPIO_ACTIVE_HIGH>;
cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
nand-bus-width = <8>;
nand-ecc-mode = "soft";
nand-on-flash-bbt;
label = "atmel_nand";
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
boot@0 {
label = "bootstrap/uboot/kernel";
reg = <0x0 0x400000>;
};
rootfs@400000 {
label = "rootfs";
reg = <0x400000 0x3C00000>;
};
data@4000000 {
label = "data";
reg = <0x4000000 0xC000000>;
};
};
};
};
};
usb0: ohci@700000 {
status = "okay";
num-ports = <2>;
atmel,vbus-gpio = <&pioD 1 GPIO_ACTIVE_LOW
&pioD 3 GPIO_ACTIVE_LOW>;
};
usb1: ehci@800000 {
status = "okay";
};
};
led-controller-1 {
compatible = "gpio-leds";
led-1 {
label = "d8";
gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
led-controller-2 {
compatible = "pwm-leds";
led-2 {
label = "d6";
pwms = <&pwm0 3 5000 PWM_POLARITY_INVERTED>;
max-brightness = <255>;
linux,default-trigger = "nand-disk";
};
led-3 {
label = "d7";
pwms = <&pwm0 1 5000 PWM_POLARITY_INVERTED>;
max-brightness = <255>;
linux,default-trigger = "mmc0";
};
};
gpio-keys {
compatible = "gpio-keys";
button-left-click {
label = "left_click";
gpios = <&pioB 6 GPIO_ACTIVE_LOW>;
linux,code = <272>;
wakeup-source;
};
button-right-click {
label = "right_click";
gpios = <&pioB 7 GPIO_ACTIVE_LOW>;
linux,code = <273>;
wakeup-source;
};
button-left {
label = "Joystick Left";
gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
linux,code = <105>;
};
button-right {
label = "Joystick Right";
gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
linux,code = <106>;
};
button-up {
label = "Joystick Up";
gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
linux,code = <103>;
};
button-down {
label = "Joystick Down";
gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
linux,code = <108>;
};
button-enter {
label = "Joystick Press";
gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
linux,code = <28>;
};
};
};