// SPDX-License-Identifier: GPL-2.0-or-later
/*
* charon board Device Tree Source
*
* Copyright (C) 2007 Semihalf
* Marian Balakowicz <m8@semihalf.com>
*
* Copyright (C) 2010 DENX Software Engineering GmbH
* Heiko Schocher <hs@denx.de>
*/
/dts-v1/;
/ {
model = "anon,charon";
compatible = "anon,charon";
#address-cells = <1>;
#size-cells = <1>;
interrupt-parent = <&mpc5200_pic>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
PowerPC,5200@0 {
device_type = "cpu";
reg = <0>;
d-cache-line-size = <32>;
i-cache-line-size = <32>;
d-cache-size = <0x4000>; // L1, 16K
i-cache-size = <0x4000>; // L1, 16K
timebase-frequency = <0>; // from bootloader
bus-frequency = <0>; // from bootloader
clock-frequency = <0>; // from bootloader
};
};
memory@0 {
device_type = "memory";
reg = <0x00000000 0x08000000>; // 128MB
};
soc5200@f0000000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc5200-immr";
ranges = <0 0xf0000000 0x0000c000>;
reg = <0xf0000000 0x00000100>;
bus-frequency = <0>; // from bootloader
system-frequency = <0>; // from bootloader
cdm@200 {
compatible = "fsl,mpc5200-cdm";
reg = <0x200 0x38>;
};
mpc5200_pic: interrupt-controller@500 {
// 5200 interrupts are encoded into two levels;
interrupt-controller;
#interrupt-cells = <3>;
compatible = "fsl,mpc5200-pic";
reg = <0x500 0x80>;
};
timer@600 { // General Purpose Timer
compatible = "fsl,mpc5200-gpt";
reg = <0x600 0x10>;
interrupts = <1 9 0>;
fsl,has-wdt;
};
can@900 {
compatible = "fsl,mpc5200-mscan";
interrupts = <2 17 0>;
reg = <0x900 0x80>;
};
can@980 {
compatible = "fsl,mpc5200-mscan";
interrupts = <2 18 0>;
reg = <0x980 0x80>;
};
gpio_simple: gpio@b00 {
compatible = "fsl,mpc5200-gpio";
reg = <0xb00 0x40>;
interrupts = <1 7 0>;
gpio-controller;
#gpio-cells = <2>;
};
usb@1000 {
compatible = "fsl,mpc5200-ohci","ohci-be";
reg = <0x1000 0xff>;
interrupts = <2 6 0>;
};
dma-controller@1200 {
device_type = "dma-controller";
compatible = "fsl,mpc5200-bestcomm";
reg = <0x1200 0x80>;
interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
3 4 0 3 5 0 3 6 0 3 7 0
3 8 0 3 9 0 3 10 0 3 11 0
3 12 0 3 13 0 3 14 0 3 15 0>;
};
xlb@1f00 {
compatible = "fsl,mpc5200-xlb";
reg = <0x1f00 0x100>;
};
serial@2000 { // PSC1
compatible = "fsl,mpc5200-psc-uart";
reg = <0x2000 0x100>;
interrupts = <2 1 0>;
};
serial@2400 { // PSC3
compatible = "fsl,mpc5200-psc-uart";
reg = <0x2400 0x100>;
interrupts = <2 3 0>;
};
ethernet@3000 {
compatible = "fsl,mpc5200-fec";
reg = <0x3000 0x400>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <2 5 0>;
fixed-link = <1 1 100 0 0>;
};
mdio@3000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200-mdio";
reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts
interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
};
ata@3a00 {
compatible = "fsl,mpc5200-ata";
reg = <0x3a00 0x100>;
interrupts = <2 7 0>;
};
i2c@3d00 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200-i2c","fsl-i2c";
reg = <0x3d00 0x40>;
interrupts = <2 15 0>;
};
i2c@3d40 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200-i2c","fsl-i2c";
reg = <0x3d40 0x40>;
interrupts = <2 16 0>;
dtt@28 {
compatible = "national,lm80";
reg = <0x28>;
};
rtc@68 {
compatible = "dallas,ds1374";
reg = <0x68>;
};
};
sram@8000 {
compatible = "fsl,mpc5200-sram";
reg = <0x8000 0x4000>;
};
};
localbus {
compatible = "fsl,mpc5200-lpb","simple-bus";
#address-cells = <2>;
#size-cells = <1>;
ranges = < 0 0 0xfc000000 0x02000000
1 0 0xe0000000 0x04000000 // CS1 range, SM501
3 0 0xe8000000 0x00080000>;
flash@0,0 {
compatible = "cfi-flash";
reg = <0 0 0x02000000>;
bank-width = <4>;
device-width = <2>;
#size-cells = <1>;
#address-cells = <1>;
};
display@1,0 {
compatible = "smi,sm501";
reg = <1 0x00000000 0x00800000
1 0x03e00000 0x00200000>;
mode = "640x480-32@60";
interrupts = <1 1 3>;
little-endian;
};
mram0@3,0 {
compatible = "mtd-ram";
reg = <3 0x00000 0x80000>;
bank-width = <1>;
};
};
pci@f0000d00 {
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
compatible = "fsl,mpc5200-pci";
reg = <0xf0000d00 0x100>;
interrupt-map-mask = <0xf800 0 0 7>;
interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3
0xc000 0 0 2 &mpc5200_pic 0 0 3
0xc000 0 0 3 &mpc5200_pic 0 0 3
0xc000 0 0 4 &mpc5200_pic 0 0 3>;
clock-frequency = <0>; // From boot loader
interrupts = <2 8 0 2 9 0 2 10 0>;
bus-range = <0 0>;
ranges = <0x42000000 0 0x80000000 0x80000000 0 0x10000000>,
<0x02000000 0 0x90000000 0x90000000 0 0x10000000>,
<0x01000000 0 0x00000000 0xa0000000 0 0x01000000>;
};
};