/* SPDX-License-Identifier: GPL-2.0-or-later */ /* * TW5864 driver - registers description * * Copyright (C) 2016 Bluecherry, LLC <maintainers@bluecherrydvr.com> */ /* According to TW5864_datasheet_0.6d.pdf, tw5864b1-ds.pdf */ /* Register Description - Direct Map Space */ /* 0x0000 ~ 0x1ffc - H264 Register Map */ /* [15:0] The Version register for H264 core (Read Only) */ #define TW5864_H264REV 0x0000 #define TW5864_EMU 0x0004 /* Define controls in register TW5864_EMU */ /* DDR controller enabled */ #define TW5864_EMU_EN_DDR BIT(0) /* Enable bit for Inter module */ #define TW5864_EMU_EN_ME BIT(1) /* Enable bit for Sensor Interface module */ #define TW5864_EMU_EN_SEN BIT(2) /* Enable bit for Host Burst Access */ #define TW5864_EMU_EN_BHOST BIT(3) /* Enable bit for Loop Filter module */ #define TW5864_EMU_EN_LPF BIT(4) /* Enable bit for PLBK module */ #define TW5864_EMU_EN_PLBK BIT(5) /* * Video Frame mapping in DDR * 00 CIF * 01 D1 * 10 Reserved * 11 Reserved * */ #define TW5864_DSP_FRAME_TYPE (3 << 6) #define TW5864_DSP_FRAME_TYPE_D1 BIT(6) #define TW5864_UNDECLARED_H264REV_PART2 0x0008 #define TW5864_SLICE 0x000c /* Define controls in register TW5864_SLICE */ /* VLC Slice end flag */ #define TW5864_VLC_SLICE_END BIT(0) /* Master Slice End Flag */ #define TW5864_MAS_SLICE_END BIT(4) /* Host to start a new slice Address */ #define TW5864_START_NSLICE BIT(15) /* * [15:0] Two bit for each channel (channel 0 ~ 7). Each two bits are the buffer * pointer for the last encoded frame of the corresponding channel. */ #define TW5864_ENC_BUF_PTR_REC1 0x0010 /* [5:0] DSP_MB_QP and [15:10] DSP_LPF_OFFSET */ #define TW5864_DSP_QP 0x0018 /* Define controls in register TW5864_DSP_QP */ /* [5:0] H264 QP Value for codec */ #define TW5864_DSP_MB_QP 0x003f /* * [15:10] H264 LPF_OFFSET Address * (Default 0) */ #define TW5864_DSP_LPF_OFFSET 0xfc00 #define TW5864_DSP_CODEC 0x001c /* Define controls in register TW5864_DSP_CODEC */ /* * 0: Encode (TW5864 Default) * 1: Decode */ #define TW5864_DSP_CODEC_MODE BIT(0) /* * 0->3 4 VLC data buffer in DDR (1M each) * 0->7 8 VLC data buffer in DDR (512k each) */ #define TW5864_VLC_BUF_ID (7 << 2) /* * 0 4CIF in 1 MB * 1 1CIF in 1 MB */ #define TW5864_CIF_MAP_MD BIT(6) /* * 0 2 falf D1 in 1 MB * 1 1 half D1 in 1 MB */ #define TW5864_HD1_MAP_MD BIT(7) /* VLC Stream valid */ #define TW5864_VLC_VLD BIT(8) /* MV Vector Valid */ #define TW5864_MV_VECT_VLD BIT(9) /* MV Flag Valid */ #define TW5864_MV_FLAG_VLD BIT(10) #define TW5864_DSP_SEN 0x0020 /* Define controls in register TW5864_DSP_SEN */ /* Org Buffer Base for Luma (default 0) */ #define TW5864_DSP_SEN_PIC_LU 0x000f /* Org Buffer Base for Chroma (default 4) */ #define TW5864_DSP_SEN_PIC_CHM 0x00f0 /* Maximum Number of Buffers (default 4) */ #define TW5864_DSP_SEN_PIC_MAX 0x0700 /* * Original Frame D1 or HD1 switch * (Default 0) */ #define TW5864_DSP_SEN_HFULL 0x1000 #define TW5864_DSP_REF_PIC 0x0024 /* Define controls in register TW5864_DSP_REF_PIC */ /* Ref Buffer Base for Luma (default 0) */ #define TW5864_DSP_REF_PIC_LU 0x000f /* Ref Buffer Base for Chroma (default 4) */ #define TW5864_DSP_REF_PIC_CHM 0x00f0 /* Maximum Number of Buffers (default 4) */ #define TW5864_DSP_REF_PIC_MAX 0x0700 /* [15:0] SEN_EN_CH[n] SENIF original frame capture enable for each channel */ #define TW5864_SEN_EN_CH 0x0028 #define TW5864_DSP 0x002c /* Define controls in register TW5864_DSP */ /* The ID for channel selected for encoding operation */ #define TW5864_DSP_ENC_CHN 0x000f /* See DSP_MB_DELAY below */ #define TW5864_DSP_MB_WAIT 0x0010 /* * DSP Chroma Switch * 0 DDRB * 1 DDRA */ #define TW5864_DSP_CHROM_SW 0x0020 /* VLC Flow Control: 1 for enable */ #define TW5864_DSP_FLW_CNTL 0x0040 /* * If DSP_MB_WAIT == 0, MB delay is DSP_MB_DELAY * 16 * If DSP_MB_DELAY == 1, MB delay is DSP_MB_DELAY * 128 */ #define TW5864_DSP_MB_DELAY 0x0f00 #define TW5864_DDR 0x0030 /* Define controls in register TW5864_DDR */ /* DDR Single Access Page Number */ #define TW5864_DDR_PAGE_CNTL 0x00ff /* DDR-DPR Burst Read Enable */ #define TW5864_DDR_BRST_EN BIT(13) /* * DDR A/B Select as HOST access * 0 Select DDRA * 1 Select DDRB */ #define TW5864_DDR_AB_SEL BIT(14) /* * DDR Access Mode Select * 0 Single R/W Access (Host <-> DDR) * 1 Burst R/W Access (Host <-> DPR) */ #define TW5864_DDR_MODE BIT(15) /* The original frame capture pointer. Two bits for each channel */ /* SENIF_ORG_FRM_PTR [15:0] */ #define TW5864_SENIF_ORG_FRM_PTR1 0x0038 /* SENIF_ORG_FRM_PTR [31:16] */ #define TW5864_SENIF_ORG_FRM_PTR2 0x003c #define TW5864_DSP_SEN_MODE 0x0040 /* Define controls in register TW5864_DSP_SEN_MODE */ #define TW5864_DSP_SEN_MODE_CH0 0x000f #define TW5864_DSP_SEN_MODE_CH1 0x00f0 /* * [15:0]: ENC_BUF_PTR_REC[31:16] Two bit for each channel (channel 8 ~ 15). * Each two bits are the buffer pointer for the last encoded frame of a channel */ #define TW5864_ENC_BUF_PTR_REC2 0x004c /* Current MV Flag Status Pointer for Channel n. (Read only) */ /* * [1:0] CH0_MV_PTR, ..., [15:14] CH7_MV_PTR */ #define TW5864_CH_MV_PTR1 0x0060 /* * [1:0] CH8_MV_PTR, ..., [15:14] CH15_MV_PTR */ #define TW5864_CH_MV_PTR2 0x0064 /* * [15:0] Reset Current MV Flag Status Pointer for Channel n (one bit each) */ #define TW5864_RST_MV_PTR 0x0068 #define TW5864_INTERLACING 0x0200 /* Define controls in register TW5864_INTERLACING */ /* * Inter_Mode Start. 2-nd bit? A guess. Missing in datasheet. Without this bit * set, the output video is interlaced (stripy). */ #define TW5864_DSP_INTER_ST BIT(1) /* Deinterlacer Enable */ #define TW5864_DI_EN BIT(2) /* * De-interlacer Mode * 1 Shuffled frame * 0 Normal Un-Shuffled Frame */ #define TW5864_DI_MD BIT(3) /* * Down scale original frame in X direction * 11: Un-used * 10: down-sample to 1/4 * 01: down-sample to 1/2 * 00: down-sample disabled */ #define TW5864_DSP_DWN_X (3 << 4) /* * Down scale original frame in Y direction * 11: Un-used * 10: down-sample to 1/4 * 01: down-sample to 1/2 * 00: down-sample disabled */ #define TW5864_DSP_DWN_Y (3 << 6) /* * 1 Dual Stream * 0 Single Stream */ #define TW5864_DUAL_STR BIT(8) #define TW5864_DSP_REF 0x0204 /* Define controls in register TW5864_DSP_REF */ /* Number of reference frame (Default 1 for TW5864B) */ #define TW5864_DSP_REF_FRM 0x000f /* Window size */ #define TW5864_DSP_WIN_SIZE 0x02f0 #define TW5864_DSP_SKIP 0x0208 /* Define controls in register TW5864_DSP_SKIP */ /* * Skip Offset Enable bit * 0 DSP_SKIP_OFFSET value is not used (default 8) * 1 DSP_SKIP_OFFSET value is used in HW */ #define TW5864_DSP_SKIP_OFEN 0x0080 /* Skip mode cost offset (default 8) */ #define TW5864_DSP_SKIP_OFFSET 0x007f #define TW5864_MOTION_SEARCH_ETC 0x020c /* Define controls in register TW5864_MOTION_SEARCH_ETC */ /* Enable quarter pel search mode */ #define TW5864_QPEL_EN BIT(0) /* Enable half pel search mode */ #define TW5864_HPEL_EN BIT(1) /* Enable motion search mode */ #define TW5864_ME_EN BIT(2) /* Enable Intra mode */ #define TW5864_INTRA_EN BIT(3) /* Enable Skip Mode */ #define TW5864_SKIP_EN BIT(4) /* Search Option (Default 2"b01) */ #define TW5864_SRCH_OPT (3 << 5) #define TW5864_DSP_ENC_REC 0x0210 /* Define controls in register TW5864_DSP_ENC_REC */ /* Reference Buffer Pointer for encoding */ #define TW5864_DSP_ENC_REF_PTR 0x0007 /* Reconstruct Buffer pointer */ #define TW5864_DSP_REC_BUF_PTR 0x7000 /* [15:0] Lambda Value for H264 */ #define TW5864_DSP_REF_MVP_LAMBDA 0x0214 #define TW5864_DSP_PIC_MAX_MB 0x0218 /* Define controls in register TW5864_DSP_PIC_MAX_MB */ /* The MB number in Y direction for a frame */ #define TW5864_DSP_PIC_MAX_MB_Y 0x007f /* The MB number in X direction for a frame */ #define TW5864_DSP_PIC_MAX_MB_X 0x7f00 /* The original frame pointer for encoding */ #define TW5864_DSP_ENC_ORG_PTR_REG 0x021c /* Mask to use with TW5864_DSP_ENC_ORG_PTR */ #define TW5864_DSP_ENC_ORG_PTR_MASK 0x7000 /* Number of bits to shift with TW5864_DSP_ENC_ORG_PTR */ #define TW5864_DSP_ENC_ORG_PTR_SHIFT 12 /* DDR base address of OSD rectangle attribute data */ #define TW5864_DSP_OSD_ATTRI_BASE 0x0220 /* OSD enable bit for each channel */ #define TW5864_DSP_OSD_ENABLE 0x0228 /* 0x0280 ~ 0x029c - Motion Vector for 1st 4x4 Block, e.g., 80 (X), 84 (Y) */ #define TW5864_ME_MV_VEC1 0x0280 /* 0x02a0 ~ 0x02bc - Motion Vector for 2nd 4x4 Block, e.g., A0 (X), A4 (Y) */ #define TW5864_ME_MV_VEC2 0x02a0 /* 0x02c0 ~ 0x02dc - Motion Vector for 3rd 4x4 Block, e.g., C0 (X), C4 (Y) */ #define TW5864_ME_MV_VEC3 0x02c0 /* 0x02e0 ~ 0x02fc - Motion Vector for 4th 4x4 Block, e.g., E0 (X), E4 (Y) */ #define TW5864_ME_MV_VEC4 0x02e0 /* * [5:0] * if (intra16x16_cost < (intra4x4_cost+dsp_i4x4_offset)) * Intra_mode = intra16x16_mode * Else * Intra_mode = intra4x4_mode */ #define TW5864_DSP_I4x4_OFFSET 0x040c /* * [6:4] * 0x5 Only 4x4 * 0x6 Only 16x16 * 0x7 16x16 & 4x4 */ #define TW5864_DSP_INTRA_MODE 0x0410 #define TW5864_DSP_INTRA_MODE_SHIFT 4 #define TW5864_DSP_INTRA_MODE_MASK (7 << 4) #define TW5864_DSP_INTRA_MODE_4x4 0x5 #define TW5864_DSP_INTRA_MODE_16x16 0x6 #define TW5864_DSP_INTRA_MODE_4x4_AND_16x16 0x7 /* * [5:0] WEIGHT Factor for I4x4 cost calculation (QP dependent) */ #define TW5864_DSP_I4x4_WEIGHT 0x0414 /* * [7:0] Offset used to affect Intra/ME model decision * If (me_cost < intra_cost + dsp_resid_mode_offset) * Pred_Mode = me_mode * Else * Pred_mode = intra_mode */ #define TW5864_DSP_RESID_MODE_OFFSET 0x0604 /* 0x0800 ~ 0x09ff - Quantization TABLE Values */ #define TW5864_QUAN_TAB 0x0800 /* Valid channel value [0; f], frame value [0; 3] */ #define TW5864_RT_CNTR_CH_FRM(channel, frame) \ (0x0c00 | (channel << 4) | (frame << 2)) #define TW5864_FRAME_BUS1 0x0d00 /* * 1 Progressive in part A in bus n * 0 Interlaced in part A in bus n */ #define TW5864_PROG_A BIT(0) /* * 1 Progressive in part B in bus n * 0 Interlaced in part B in bus n */ #define TW5864_PROG_B BIT(1) /* * 1 Frame Mode in bus n * 0 Field Mode in bus n */ #define TW5864_FRAME BIT(2) /* * 0 4CIF in bus n * 1 1D1 + 4 CIF in bus n * 2 2D1 in bus n */ #define TW5864_BUS_D1 (3 << 3) /* Bus 1 goes in TW5864_FRAME_BUS1 in [4:0] */ /* Bus 2 goes in TW5864_FRAME_BUS1 in [12:8] */ #define TW5864_FRAME_BUS2 0x0d04 /* Bus 3 goes in TW5864_FRAME_BUS2 in [4:0] */ /* Bus 4 goes in TW5864_FRAME_BUS2 in [12:8] */ /* [15:0] Horizontal Mirror for channel n */ #define TW5864_SENIF_HOR_MIR 0x0d08 /* [15:0] Vertical Mirror for channel n */ #define TW5864_SENIF_VER_MIR 0x0d0c /* * FRAME_WIDTH_BUSn_A * 0x15f: 4 CIF * 0x2cf: 1 D1 + 3 CIF * 0x2cf: 2 D1 * FRAME_WIDTH_BUSn_B * 0x15f: 4 CIF * 0x2cf: 1 D1 + 3 CIF * 0x2cf: 2 D1 * FRAME_HEIGHT_BUSn_A * 0x11f: 4CIF (PAL) * 0x23f: 1D1 + 3CIF (PAL) * 0x23f: 2 D1 (PAL) * 0x0ef: 4CIF (NTSC) * 0x1df: 1D1 + 3CIF (NTSC) * 0x1df: 2 D1 (NTSC) * FRAME_HEIGHT_BUSn_B * 0x11f: 4CIF (PAL) * 0x23f: 1D1 + 3CIF (PAL) * 0x23f: 2 D1 (PAL) * 0x0ef: 4CIF (NTSC) * 0x1df: 1D1 + 3CIF (NTSC) * 0x1df: 2 D1 (NTSC) */ #define TW5864_FRAME_WIDTH_BUS_A(bus) (0x0d10 + 0x0010 * bus) #define TW5864_FRAME_WIDTH_BUS_B(bus) (0x0d14 + 0x0010 * bus) #define TW5864_FRAME_HEIGHT_BUS_A(bus) (0x0d18 + 0x0010 * bus) #define TW5864_FRAME_HEIGHT_BUS_B(bus) (0x0d1c + 0x0010 * bus) /* * 1: the bus mapped Channel n Full D1 * 0: the bus mapped Channel n Half D1 */ #define TW5864_FULL_HALF_FLAG 0x0d50 /* * 0 The bus mapped Channel select partA Mode * 1 The bus mapped Channel select partB Mode */ #define TW5864_FULL_HALF_MODE_SEL 0x0d54 #define TW5864_VLC 0x1000 /* Define controls in register TW5864_VLC */ /* QP Value used by H264 CAVLC */ #define TW5864_VLC_SLICE_QP 0x003f /* * Swap byte order of VLC stream in d-word. * 1 Normal (VLC output= [31:0]) * 0 Swap (VLC output={[23:16],[31:24],[7:0], [15:8]}) */ #define TW5864_VLC_BYTE_SWP BIT(6) /* Enable Adding 03 circuit for VLC stream */ #define TW5864_VLC_ADD03_EN BIT(7) /* Number of bit for VLC bit Align */ #define TW5864_VLC_BIT_ALIGN_SHIFT 8 #define TW5864_VLC_BIT_ALIGN_MASK (0x1f << 8) /* * Synchronous Interface select for VLC Stream * 1 CDC_VLCS_MAS read VLC stream * 0 CPU read VLC stream */ #define TW5864_VLC_INF_SEL BIT(13) /* Enable VLC overflow control */ #define TW5864_VLC_OVFL_CNTL BIT(14) /* * 1 PCI Master Mode * 0 Non PCI Master Mode */ #define TW5864_VLC_PCI_SEL BIT(15) /* * 0 Enable Adding 03 to VLC header and stream * 1 Disable Adding 03 to VLC header of "00000001" */ #define TW5864_VLC_A03_DISAB BIT(16) /* * Status of VLC stream in DDR (one bit for each buffer) * 1 VLC is ready in buffer n (HW set) * 0 VLC is not ready in buffer n (SW clear) */ #define TW5864_VLC_BUF_RDY_SHIFT 24 #define TW5864_VLC_BUF_RDY_MASK (0xff << 24) /* Total number of bit in the slice */ #define TW5864_SLICE_TOTAL_BIT 0x1004 /* Total number of bit in the residue */ #define TW5864_RES_TOTAL_BIT 0x1008 #define TW5864_VLC_BUF 0x100c /* Define controls in register TW5864_VLC_BUF */ /* VLC BK0 full status, write '1' to clear */ #define TW5864_VLC_BK0_FULL BIT(0) /* VLC BK1 full status, write '1' to clear */ #define TW5864_VLC_BK1_FULL BIT(1) /* VLC end slice status, write '1' to clear */ #define TW5864_VLC_END_SLICE BIT(2) /* VLC Buffer overflow status, write '1' to clear */ #define TW5864_DSP_RD_OF BIT(3) /* VLC string length in either buffer 0 or 1 at end of frame */ #define TW5864_VLC_STREAM_LEN_SHIFT 4 #define TW5864_VLC_STREAM_LEN_MASK (0x1ff << 4) /* [15:0] Total coefficient number in a frame */ #define TW5864_TOTAL_COEF_NO 0x1010 /* [0] VLC Encoder Interrupt. Write '1' to clear */ #define TW5864_VLC_DSP_INTR 0x1014 /* [31:0] VLC stream CRC checksum */ #define TW5864_VLC_STREAM_CRC 0x1018 #define TW5864_VLC_RD 0x101c /* Define controls in register TW5864_VLC_RD */ /* * 1 Read VLC lookup Memory * 0 Read VLC Stream Memory */ #define TW5864_VLC_RD_MEM BIT(0) /* * 1 Read VLC Stream Memory in burst mode * 0 Read VLC Stream Memory in single mode */ #define TW5864_VLC_RD_BRST BIT(1) /* 0x2000 ~ 0x2ffc - H264 Stream Memory Map */ /* * A word is 4 bytes. I.e., * VLC_STREAM_MEM[0] address: 0x2000 * VLC_STREAM_MEM[1] address: 0x2004 * ... * VLC_STREAM_MEM[3FF] address: 0x2ffc */ #define TW5864_VLC_STREAM_MEM_START 0x2000 #define TW5864_VLC_STREAM_MEM_MAX_OFFSET 0x3ff #define TW5864_VLC_STREAM_MEM(offset) (TW5864_VLC_STREAM_MEM_START + 4 * offset) /* 0x4000 ~ 0x4ffc - Audio Register Map */ /* [31:0] config 1ms cnt = Realtime clk/1000 */ #define TW5864_CFG_1MS_CNT 0x4000 #define TW5864_ADPCM 0x4004 /* Define controls in register TW5864_ADPCM */ /* ADPCM decoder enable */ #define TW5864_ADPCM_DEC BIT(0) /* ADPCM input data enable */ #define TW5864_ADPCM_IN_DATA BIT(1) /* ADPCM encoder enable */ #define TW5864_ADPCM_ENC BIT(2) #define TW5864_AUD 0x4008 /* Define controls in register TW5864_AUD */ /* Record path PCM Audio enable bit for each channel */ #define TW5864_AUD_ORG_CH_EN 0x00ff /* Speaker path PCM Audio Enable */ #define TW5864_SPK_ORG_EN BIT(16) /* * 0 16bit * 1 8bit */ #define TW5864_AD_BIT_MODE BIT(17) #define TW5864_AUD_TYPE_SHIFT 18 /* * 0 PCM * 3 ADPCM */ #define TW5864_AUD_TYPE (0xf << 18) #define TW5864_AUD_SAMPLE_RATE_SHIFT 22 /* * 0 8K * 1 16K */ #define TW5864_AUD_SAMPLE_RATE (3 << 22) /* Channel ID used to select audio channel (0 to 16) for loopback */ #define TW5864_TESTLOOP_CHID_SHIFT 24 #define TW5864_TESTLOOP_CHID (0x1f << 24) /* Enable AD Loopback Test */ #define TW5864_TEST_ADLOOP_EN BIT(30) /* * 0 Asynchronous Mode or PCI target mode * 1 PCI Initiator Mode */ #define TW5864_AUD_MODE BIT(31) #define TW5864_AUD_ADPCM 0x400c /* Define controls in register TW5864_AUD_ADPCM */ /* Record path ADPCM audio channel enable, one bit for each */ #define TW5864_AUD_ADPCM_CH_EN 0x00ff /* Speaker path ADPCM audio channel enable */ #define TW5864_SPK_ADPCM_EN BIT(16) #define TW5864_PC_BLOCK_ADPCM_RD_NO 0x4018 #define TW5864_PC_BLOCK_ADPCM_RD_NO_MASK 0x1f /* * For ADPCM_ENC_WR_PTR, ADPCM_ENC_RD_PTR (see below): * Bit[2:0] ch0 * Bit[5:3] ch1 * Bit[8:6] ch2 * Bit[11:9] ch3 * Bit[14:12] ch4 * Bit[17:15] ch5 * Bit[20:18] ch6 * Bit[23:21] ch7 * Bit[26:24] ch8 * Bit[29:27] ch9 * Bit[32:30] ch10 * Bit[35:33] ch11 * Bit[38:36] ch12 * Bit[41:39] ch13 * Bit[44:42] ch14 * Bit[47:45] ch15 * Bit[50:48] ch16 */ #define TW5864_ADPCM_ENC_XX_MASK 0x3fff #define TW5864_ADPCM_ENC_XX_PTR2_SHIFT 30 /* ADPCM_ENC_WR_PTR[29:0] */ #define TW5864_ADPCM_ENC_WR_PTR1 0x401c /* ADPCM_ENC_WR_PTR[50:30] */ #define TW5864_ADPCM_ENC_WR_PTR2 0x4020 /* ADPCM_ENC_RD_PTR[29:0] */ #define TW5864_ADPCM_ENC_RD_PTR1 0x4024 /* ADPCM_ENC_RD_PTR[50:30] */ #define TW5864_ADPCM_ENC_RD_PTR2 0x4028 /* [3:0] rd ch0, [7:4] rd ch1, [11:8] wr ch0, [15:12] wr ch1 */ #define TW5864_ADPCM_DEC_RD_WR_PTR 0x402c /* * For TW5864_AD_ORIG_WR_PTR, TW5864_AD_ORIG_RD_PTR: * Bit[3:0] ch0 * Bit[7:4] ch1 * Bit[11:8] ch2 * Bit[15:12] ch3 * Bit[19:16] ch4 * Bit[23:20] ch5 * Bit[27:24] ch6 * Bit[31:28] ch7 * Bit[35:32] ch8 * Bit[39:36] ch9 * Bit[43:40] ch10 * Bit[47:44] ch11 * Bit[51:48] ch12 * Bit[55:52] ch13 * Bit[59:56] ch14 * Bit[63:60] ch15 * Bit[67:64] ch16 */ /* AD_ORIG_WR_PTR[31:0] */ #define TW5864_AD_ORIG_WR_PTR1 0x4030 /* AD_ORIG_WR_PTR[63:32] */ #define TW5864_AD_ORIG_WR_PTR2 0x4034 /* AD_ORIG_WR_PTR[67:64] */ #define TW5864_AD_ORIG_WR_PTR3 0x4038 /* AD_ORIG_RD_PTR[31:0] */ #define TW5864_AD_ORIG_RD_PTR1 0x403c /* AD_ORIG_RD_PTR[63:32] */ #define TW5864_AD_ORIG_RD_PTR2 0x4040 /* AD_ORIG_RD_PTR[67:64] */ #define TW5864_AD_ORIG_RD_PTR3 0x4044 #define TW5864_PC_BLOCK_ORIG_RD_NO 0x4048 #define TW5864_PC_BLOCK_ORIG_RD_NO_MASK 0x1f #define TW5864_PCI_AUD 0x404c /* Define controls in register TW5864_PCI_AUD */ /* * The register is applicable to PCI initiator mode only. Used to select PCM(0) * or ADPCM(1) audio data sent to PC. One bit for each channel */ #define TW5864_PCI_DATA_SEL 0xffff /* * Audio flow control mode selection bit. * 0 Flow control disabled. TW5864 continuously sends audio frame to PC * (initiator mode) * 1 Flow control enabled */ #define TW5864_PCI_FLOW_EN BIT(16) /* * When PCI_FLOW_EN is set, PCI need to toggle this bit to send an audio frame * to PC. One toggle to send one frame. */ #define TW5864_PCI_AUD_FRM_EN BIT(17) /* [1:0] CS valid to data valid CLK cycles when writing operation */ #define TW5864_CS2DAT_CNT 0x8000 /* [2:0] Data valid signal width by system clock cycles */ #define TW5864_DATA_VLD_WIDTH 0x8004 #define TW5864_SYNC 0x8008 /* Define controls in register TW5864_SYNC */ /* * 0 vlc stream to synchronous port * 1 vlc stream to ddr buffers */ #define TW5864_SYNC_CFG BIT(7) /* * 0 SYNC Address sampled on Rising edge * 1 SYNC Address sampled on Falling edge */ #define TW5864_SYNC_ADR_EDGE BIT(0) #define TW5864_VLC_STR_DELAY_SHIFT 1 /* * 0 No system delay * 1 One system clock delay * 2 Two system clock delay * 3 Three system clock delay */ #define TW5864_VLC_STR_DELAY (3 << 1) /* * 0 Rising edge output * 1 Falling edge output */ #define TW5864_VLC_OUT_EDGE BIT(3) /* * [1:0] * 2'b00 phase set to 180 degree * 2'b01 phase set to 270 degree * 2'b10 phase set to 0 degree * 2'b11 phase set to 90 degree */ #define TW5864_I2C_PHASE_CFG 0x800c /* * The system / DDR clock (166 MHz) is generated with an on-chip system clock * PLL (SYSPLL) using input crystal clock of 27 MHz. The system clock PLL * frequency is controlled with the following equation. * CLK_OUT = CLK_IN * (M+1) / ((N+1) * P) * SYSPLL_M M parameter * SYSPLL_N N parameter * SYSPLL_P P parameter */ /* SYSPLL_M[7:0] */ #define TW5864_SYSPLL1 0x8018 /* Define controls in register TW5864_SYSPLL1 */ #define TW5864_SYSPLL_M_LOW 0x00ff /* [2:0]: SYSPLL_M[10:8], [7:3]: SYSPLL_N[4:0] */ #define TW5864_SYSPLL2 0x8019 /* Define controls in register TW5864_SYSPLL2 */ #define TW5864_SYSPLL_M_HI 0x07 #define TW5864_SYSPLL_N_LOW_SHIFT 3 #define TW5864_SYSPLL_N_LOW (0x1f << 3) /* * [1:0]: SYSPLL_N[6:5], [3:2]: SYSPLL_P, [4]: SYSPLL_IREF, [7:5]: SYSPLL_CP_SEL */ #define TW5864_SYSPLL3 0x8020 /* Define controls in register TW5864_SYSPLL3 */ #define TW5864_SYSPLL_N_HI 0x03 #define TW5864_SYSPLL_P_SHIFT 2 #define TW5864_SYSPLL_P (0x03 << 2) /* * SYSPLL bias current control * 0 Lower current (default) * 1 30% higher current */ #define TW5864_SYSPLL_IREF BIT(4) /* * SYSPLL charge pump current selection * 0 1,5 uA * 1 4 uA * 2 9 uA * 3 19 uA * 4 39 uA * 5 79 uA * 6 159 uA * 7 319 uA */ #define TW5864_SYSPLL_CP_SEL_SHIFT 5 #define TW5864_SYSPLL_CP_SEL (0x07 << 5) /* * [1:0]: SYSPLL_VCO, [3:2]: SYSPLL_LP_X8, [5:4]: SYSPLL_ICP_SEL, * [6]: SYSPLL_LPF_5PF, [7]: SYSPLL_ED_SEL */ #define TW5864_SYSPLL4 0x8021 /* Define controls in register TW5864_SYSPLL4 */ /* * SYSPLL_VCO VCO Range selection * 00 5 ~ 75 MHz * 01 50 ~ 140 MHz * 10 110 ~ 320 MHz * 11 270 ~ 700 MHz */ #define TW5864_SYSPLL_VCO 0x03 #define TW5864_SYSPLL_LP_X8_SHIFT 2 /* * Loop resister * 0 38.5K ohms * 1 6.6K ohms (default) * 2 2.2K ohms * 3 1.1K ohms */ #define TW5864_SYSPLL_LP_X8 (0x03 << 2) #define TW5864_SYSPLL_ICP_SEL_SHIFT 4 /* * PLL charge pump fine tune * 00 x1 (default) * 01 x1/2 * 10 x1/7 * 11 x1/8 */ #define TW5864_SYSPLL_ICP_SEL (0x03 << 4) /* * PLL low pass filter phase margin adjustment * 0 no 5pF (default) * 1 5pF added */ #define TW5864_SYSPLL_LPF_5PF BIT(6) /* * PFD select edge for detection * 0 Falling edge (default) * 1 Rising edge */ #define TW5864_SYSPLL_ED_SEL BIT(7) /* [0]: SYSPLL_RST, [4]: SYSPLL_PD */ #define TW5864_SYSPLL5 0x8024 /* Define controls in register TW5864_SYSPLL5 */ /* Reset SYSPLL */ #define TW5864_SYSPLL_RST BIT(0) /* Power down SYSPLL */ #define TW5864_SYSPLL_PD BIT(4) #define TW5864_PLL_CFG 0x801c /* Define controls in register TW5864_PLL_CFG */ /* * Issue Soft Reset from Async Host Interface / PCI Interface clock domain. * Become valid after sync to the xtal clock domain. This bit is set only if * LOAD register bit is also set to 1. */ #define TW5864_SRST BIT(0) /* * Issue SYSPLL (166 MHz) configuration latch from Async host interface / PCI * Interface clock domain. The configuration setting becomes effective only if * LOAD register bit is also set to 1. */ #define TW5864_SYSPLL_CFG BIT(2) /* * Issue SPLL (108 MHz) configuration load from Async host interface / PCI * Interface clock domain. The configuration setting becomes effective only if * the LOAD register bit is also set to 1. */ #define TW5864_SPLL_CFG BIT(4) /* * Set this bit to latch the SRST, SYSPLL_CFG, SPLL_CFG setting into the xtal * clock domain to restart the PLL. This bit is self cleared. */ #define TW5864_LOAD BIT(3) /* SPLL_IREF, SPLL_LPX4, SPLL_CPX4, SPLL_PD, SPLL_DBG */ #define TW5864_SPLL 0x8028 /* 0x8800 ~ 0x88fc - Interrupt Register Map */ /* * Trigger mode of interrupt source 0 ~ 15 * 1 Edge trigger mode * 0 Level trigger mode */ #define TW5864_TRIGGER_MODE_L 0x8800 /* Trigger mode of interrupt source 16 ~ 31 */ #define TW5864_TRIGGER_MODE_H 0x8804 /* Enable of interrupt source 0 ~ 15 */ #define TW5864_INTR_ENABLE_L 0x8808 /* Enable of interrupt source 16 ~ 31 */ #define TW5864_INTR_ENABLE_H 0x880c /* Clear interrupt command of interrupt source 0 ~ 15 */ #define TW5864_INTR_CLR_L 0x8810 /* Clear interrupt command of interrupt source 16 ~ 31 */ #define TW5864_INTR_CLR_H 0x8814 /* * Assertion of interrupt source 0 ~ 15 * 1 High level or pos-edge is assertion * 0 Low level or neg-edge is assertion */ #define TW5864_INTR_ASSERT_L 0x8818 /* Assertion of interrupt source 16 ~ 31 */ #define TW5864_INTR_ASSERT_H 0x881c /* * Output level of interrupt * 1 Interrupt output is high assertion * 0 Interrupt output is low assertion */ #define TW5864_INTR_OUT_LEVEL 0x8820 /* * Status of interrupt source 0 ~ 15 * Bit[0]: VLC 4k RAM interrupt * Bit[1]: BURST DDR RAM interrupt * Bit[2]: MV DSP interrupt * Bit[3]: video lost interrupt * Bit[4]: gpio 0 interrupt * Bit[5]: gpio 1 interrupt * Bit[6]: gpio 2 interrupt * Bit[7]: gpio 3 interrupt * Bit[8]: gpio 4 interrupt * Bit[9]: gpio 5 interrupt * Bit[10]: gpio 6 interrupt * Bit[11]: gpio 7 interrupt * Bit[12]: JPEG interrupt * Bit[13:15]: Reserved */ #define TW5864_INTR_STATUS_L 0x8838 /* * Status of interrupt source 16 ~ 31 * Bit[0]: Reserved * Bit[1]: VLC done interrupt * Bit[2]: Reserved * Bit[3]: AD Vsync interrupt * Bit[4]: Preview eof interrupt * Bit[5]: Preview overflow interrupt * Bit[6]: Timer interrupt * Bit[7]: Reserved * Bit[8]: Audio eof interrupt * Bit[9]: I2C done interrupt * Bit[10]: AD interrupt * Bit[11:15]: Reserved */ #define TW5864_INTR_STATUS_H 0x883c /* Defines of interrupt bits, united for both low and high word registers */ #define TW5864_INTR_VLC_RAM BIT(0) #define TW5864_INTR_BURST BIT(1) #define TW5864_INTR_MV_DSP BIT(2) #define TW5864_INTR_VIN_LOST BIT(3) /* n belongs to [0; 7] */ #define TW5864_INTR_GPIO(n) (1 << (4 + n)) #define TW5864_INTR_JPEG BIT(12) #define TW5864_INTR_VLC_DONE BIT(17) #define TW5864_INTR_AD_VSYNC BIT(19) #define TW5864_INTR_PV_EOF BIT(20) #define TW5864_INTR_PV_OVERFLOW BIT(21) #define TW5864_INTR_TIMER BIT(22) #define TW5864_INTR_AUD_EOF BIT(24) #define TW5864_INTR_I2C_DONE BIT(25) #define TW5864_INTR_AD BIT(26) /* 0x9000 ~ 0x920c - Video Capture (VIF) Register Map */ /* * H264EN_CH_STATUS[n] Status of Vsync synchronized H264EN_CH_EN (Read Only) * 1 Channel Enabled * 0 Channel Disabled */ #define TW5864_H264EN_CH_STATUS 0x9000 /* * [15:0] H264EN_CH_EN[n] H264 Encoding Path Enable for channel * 1 Channel Enabled * 0 Channel Disabled */ #define TW5864_H264EN_CH_EN 0x9004 /* * H264EN_CH_DNS[n] H264 Encoding Path Downscale Video Decoder Input for * channel n * 1 Downscale Y to 1/2 * 0 Does not downscale */ #define TW5864_H264EN_CH_DNS 0x9008 /* * H264EN_CH_PROG[n] H264 Encoding Path channel n is progressive * 1 Progressive (Not valid for TW5864) * 0 Interlaced (TW5864 default) */ #define TW5864_H264EN_CH_PROG 0x900c /* * [3:0] H264EN_BUS_MAX_CH[n] * H264 Encoding Path maximum number of channel on BUS n * 0 Max 4 channels * 1 Max 2 channels */ #define TW5864_H264EN_BUS_MAX_CH 0x9010 /* * H264EN_RATE_MAX_LINE_n H264 Encoding path Rate Mapping Maximum Line Number * on Bus n */ #define TW5864_H264EN_RATE_MAX_LINE_EVEN 0x1f #define TW5864_H264EN_RATE_MAX_LINE_ODD_SHIFT 5 #define TW5864_H264EN_RATE_MAX_LINE_ODD (0x1f << 5) /* * [4:0] H264EN_RATE_MAX_LINE_0 * [9:5] H264EN_RATE_MAX_LINE_1 */ #define TW5864_H264EN_RATE_MAX_LINE_REG1 0x9014 /* * [4:0] H264EN_RATE_MAX_LINE_2 * [9:5] H264EN_RATE_MAX_LINE_3 */ #define TW5864_H264EN_RATE_MAX_LINE_REG2 0x9018 /* * H264EN_CHn_FMT H264 Encoding Path Format configuration of Channel n * 00 D1 (For D1 and hD1 frame) * 01 (Reserved) * 10 (Reserved) * 11 D1 with 1/2 size in X (for CIF frame) * Note: To be used with 0x9008 register to configure the frame size */ /* * [1:0]: H264EN_CH0_FMT, * ..., [15:14]: H264EN_CH7_FMT */ #define TW5864_H264EN_CH_FMT_REG1 0x9020 /* * [1:0]: H264EN_CH8_FMT (?), * ..., [15:14]: H264EN_CH15_FMT (?) */ #define TW5864_H264EN_CH_FMT_REG2 0x9024 /* * H264EN_RATE_CNTL_BUSm_CHn H264 Encoding Path BUS m Rate Control for Channel n */ #define TW5864_H264EN_RATE_CNTL_LO_WORD(bus, channel) \ (0x9100 + bus * 0x20 + channel * 0x08) #define TW5864_H264EN_RATE_CNTL_HI_WORD(bus, channel) \ (0x9104 + bus * 0x20 + channel * 0x08) /* * H264EN_BUSm_MAP_CHn The 16-to-1 MUX configuration register for each encoding * channel (total of 16 channels). Four bits for each channel. */ #define TW5864_H264EN_BUS0_MAP 0x9200 #define TW5864_H264EN_BUS1_MAP 0x9204 #define TW5864_H264EN_BUS2_MAP 0x9208 #define TW5864_H264EN_BUS3_MAP 0x920c /* This register is not defined in datasheet, but used in reference driver */ #define TW5864_UNDECLARED_ERROR_FLAGS_0x9218 0x9218 #define TW5864_GPIO1 0x9800 #define TW5864_GPIO2 0x9804 /* Define controls in registers TW5864_GPIO1, TW5864_GPIO2 */ /* GPIO DATA of Group n */ #define TW5864_GPIO_DATA 0x00ff #define TW5864_GPIO_OEN_SHIFT 8 /* GPIO Output Enable of Group n */ #define TW5864_GPIO_OEN (0xff << 8) /* 0xa000 ~ 0xa8ff - DDR Controller Register Map */ /* DDR Controller A */ /* * [2:0] Data valid counter after read command to DDR. This is the delay value * to show how many cycles the data will be back from DDR after we issue a read * command. */ #define TW5864_RD_ACK_VLD_MUX 0xa000 #define TW5864_DDR_PERIODS 0xa004 /* Define controls in register TW5864_DDR_PERIODS */ /* * Tras value, the minimum cycle of active to precharge command period, * default is 7 */ #define TW5864_TRAS_CNT_MAX 0x000f /* * Trfc value, the minimum cycle of refresh to active or refresh command period, * default is 4"hf */ #define TW5864_RFC_CNT_MAX_SHIFT 8 #define TW5864_RFC_CNT_MAX (0x0f << 8) /* * Trcd value, the minimum cycle of active to internal read/write command * period, default is 4"h2 */ #define TW5864_TCD_CNT_MAX_SHIFT 4 #define TW5864_TCD_CNT_MAX (0x0f << 4) /* Twr value, write recovery time, default is 4"h3 */ #define TW5864_TWR_CNT_MAX_SHIFT 12 #define TW5864_TWR_CNT_MAX (0x0f << 12) /* * [2:0] CAS latency, the delay cycle between internal read command and the * availability of the first bit of output data, default is 3 */ #define TW5864_CAS_LATENCY 0xa008 /* * [15:0] Maximum average periodic refresh, the value is based on the current * frequency to match 7.8mcs */ #define TW5864_DDR_REF_CNTR_MAX 0xa00c /* * DDR_ON_CHIP_MAP [1:0] * 0 256M DDR on board * 1 512M DDR on board * 2 1G DDR on board * DDR_ON_CHIP_MAP [2] * 0 Only one DDR chip * 1 Two DDR chips */ #define TW5864_DDR_ON_CHIP_MAP 0xa01c #define TW5864_DDR_SELFTEST_MODE 0xa020 /* Define controls in register TW5864_DDR_SELFTEST_MODE */ /* * 0 Common read/write mode * 1 DDR self-test mode */ #define TW5864_MASTER_MODE BIT(0) /* * 0 DDR self-test single read/write * 1 DDR self-test burst read/write */ #define TW5864_SINGLE_PROC BIT(1) /* * 0 DDR self-test write command * 1 DDR self-test read command */ #define TW5864_WRITE_FLAG BIT(2) #define TW5864_DATA_MODE_SHIFT 4 /* * 0 write 32'haaaa5555 to DDR * 1 write 32'hffffffff to DDR * 2 write 32'hha5a55a5a to DDR * 3 write increasing data to DDR */ #define TW5864_DATA_MODE (0x3 << 4) /* [7:0] The maximum data of one burst in DDR self-test mode */ #define TW5864_BURST_CNTR_MAX 0xa024 /* [15:0] The maximum burst counter (bit 15~0) in DDR self-test mode */ #define TW5864_DDR_PROC_CNTR_MAX_L 0xa028 /* The maximum burst counter (bit 31~16) in DDR self-test mode */ #define TW5864_DDR_PROC_CNTR_MAX_H 0xa02c /* [0]: Start one DDR self-test */ #define TW5864_DDR_SELF_TEST_CMD 0xa030 /* The maximum error counter (bit 15 ~ 0) in DDR self-test */ #define TW5864_ERR_CNTR_L 0xa034 #define TW5864_ERR_CNTR_H_AND_FLAG 0xa038 /* Define controls in register TW5864_ERR_CNTR_H_AND_FLAG */ /* The maximum error counter (bit 30 ~ 16) in DDR self-test */ #define TW5864_ERR_CNTR_H_MASK 0x3fff /* DDR self-test end flag */ #define TW5864_END_FLAG 0x8000 /* * DDR Controller B: same as 0xa000 ~ 0xa038, but add TW5864_DDR_B_OFFSET to all * addresses */ #define TW5864_DDR_B_OFFSET 0x0800 /* 0xb004 ~ 0xb018 - HW version/ARB12 Register Map */ /* [15:0] Default is C013 */ #define TW5864_HW_VERSION 0xb004 #define TW5864_REQS_ENABLE 0xb010 /* Define controls in register TW5864_REQS_ENABLE */ /* Audio data in to DDR enable (default 1) */ #define TW5864_AUD_DATA_IN_ENB BIT(0) /* Audio encode request to DDR enable (default 1) */ #define TW5864_AUD_ENC_REQ_ENB BIT(1) /* Audio decode request0 to DDR enable (default 1) */ #define TW5864_AUD_DEC_REQ0_ENB BIT(2) /* Audio decode request1 to DDR enable (default 1) */ #define TW5864_AUD_DEC_REQ1_ENB BIT(3) /* VLC stream request to DDR enable (default 1) */ #define TW5864_VLC_STRM_REQ_ENB BIT(4) /* H264 MV request to DDR enable (default 1) */ #define TW5864_DVM_MV_REQ_ENB BIT(5) /* mux_core MVD request to DDR enable (default 1) */ #define TW5864_MVD_REQ_ENB BIT(6) /* mux_core MVD temp data request to DDR enable (default 1) */ #define TW5864_MVD_TMP_REQ_ENB BIT(7) /* JPEG request to DDR enable (default 1) */ #define TW5864_JPEG_REQ_ENB BIT(8) /* mv_flag request to DDR enable (default 1) */ #define TW5864_MV_FLAG_REQ_ENB BIT(9) #define TW5864_ARB12 0xb018 /* Define controls in register TW5864_ARB12 */ /* ARB12 Enable (default 1) */ #define TW5864_ARB12_ENB BIT(15) /* ARB12 maximum value of time out counter (default 15"h1FF) */ #define TW5864_ARB12_TIME_OUT_CNT 0x7fff /* 0xb800 ~ 0xb80c - Indirect Access Register Map */ /* * Spec says: * In order to access the indirect register space, the following procedure is * followed. * But reference driver implementation, and current driver, too, does it * differently. * * Write Registers: * (1) Write IND_DATA at 0xb804 ~ 0xb807 * (2) Read BUSY flag from 0xb803. Wait until BUSY signal is 0. * (3) Write IND_ADDR at 0xb800 ~ 0xb801. Set R/W to "1", ENABLE to "1" * Read Registers: * (1) Read BUSY flag from 0xb803. Wait until BUSY signal is 0. * (2) Write IND_ADDR at 0xb800 ~ 0xb801. Set R/W to "0", ENABLE to "1" * (3) Read BUSY flag from 0xb803. Wait until BUSY signal is 0. * (4) Read IND_DATA from 0xb804 ~ 0xb807 */ #define TW5864_IND_CTL 0xb800 /* Define controls in register TW5864_IND_CTL */ /* Address used to access indirect register space */ #define TW5864_IND_ADDR 0x0000ffff /* Wait until this bit is "0" before using indirect access */ #define TW5864_BUSY BIT(31) /* Activate the indirect access. This bit is self cleared */ #define TW5864_ENABLE BIT(25) /* Read/Write command */ #define TW5864_RW BIT(24) /* [31:0] Data used to read/write indirect register space */ #define TW5864_IND_DATA 0xb804 /* 0xc000 ~ 0xc7fc - Preview Register Map */ /* Mostly skipped this section. */ /* * [15:0] Status of Vsync Synchronized PCI_PV_CH_EN (Read Only) * 1 Channel Enabled * 0 Channel Disabled */ #define TW5864_PCI_PV_CH_STATUS 0xc000 /* * [15:0] PCI Preview Path Enable for channel n * 1 Channel Enable * 0 Channel Disable */ #define TW5864_PCI_PV_CH_EN 0xc004 /* 0xc800 ~ 0xc804 - JPEG Capture Register Map */ /* Skipped. */ /* 0xd000 ~ 0xd0fc - JPEG Control Register Map */ /* Skipped. */ /* 0xe000 ~ 0xfc04 - Motion Vector Register Map */ /* ME Motion Vector data (Four Byte Each) 0xe000 ~ 0xe7fc */ #define TW5864_ME_MV_VEC_START 0xe000 #define TW5864_ME_MV_VEC_MAX_OFFSET 0x1ff #define TW5864_ME_MV_VEC(offset) (TW5864_ME_MV_VEC_START + 4 * offset) #define TW5864_MV 0xfc00 /* Define controls in register TW5864_MV */ /* mv bank0 full status , write "1" to clear */ #define TW5864_MV_BK0_FULL BIT(0) /* mv bank1 full status , write "1" to clear */ #define TW5864_MV_BK1_FULL BIT(1) /* slice end status; write "1" to clear */ #define TW5864_MV_EOF BIT(2) /* mv encode interrupt status; write "1" to clear */ #define TW5864_MV_DSP_INTR BIT(3) /* mv write memory overflow, write "1" to clear */ #define TW5864_DSP_WR_OF BIT(4) #define TW5864_MV_LEN_SHIFT 5 /* mv stream length */ #define TW5864_MV_LEN (0xff << 5) /* The configured status bit written into bit 15 of 0xfc04 */ #define TW5864_MPI_DDR_SEL BIT(13) #define TW5864_MPI_DDR_SEL_REG 0xfc04 /* Define controls in register TW5864_MPI_DDR_SEL_REG */ /* * SW configure register * 0 MV is saved in internal DPR * 1 MV is saved in DDR */ #define TW5864_MPI_DDR_SEL2 BIT(15) /* 0x18000 ~ 0x181fc - PCI Master/Slave Control Map */ #define TW5864_PCI_INTR_STATUS 0x18000 /* Define controls in register TW5864_PCI_INTR_STATUS */ /* vlc done */ #define TW5864_VLC_DONE_INTR BIT(1) /* ad vsync */ #define TW5864_AD_VSYNC_INTR BIT(3) /* preview eof */ #define TW5864_PREV_EOF_INTR BIT(4) /* preview overflow interrupt */ #define TW5864_PREV_OVERFLOW_INTR BIT(5) /* timer interrupt */ #define TW5864_TIMER_INTR BIT(6) /* audio eof */ #define TW5864_AUDIO_EOF_INTR BIT(8) /* IIC done */ #define TW5864_IIC_DONE_INTR BIT(24) /* ad interrupt (e.g.: video lost, video format changed) */ #define TW5864_AD_INTR_REG BIT(25) #define TW5864_PCI_INTR_CTL 0x18004 /* Define controls in register TW5864_PCI_INTR_CTL */ /* master enable */ #define TW5864_PCI_MAST_ENB BIT(0) /* mvd&vlc master enable */ #define TW5864_MVD_VLC_MAST_ENB 0x06 /* (Need to set 0 in TW5864A) */ #define TW5864_AD_MAST_ENB BIT(3) /* preview master enable */ #define TW5864_PREV_MAST_ENB BIT(4) /* preview overflow enable */ #define TW5864_PREV_OVERFLOW_ENB BIT(5) /* timer interrupt enable */ #define TW5864_TIMER_INTR_ENB BIT(6) /* JPEG master (push mode) enable */ #define TW5864_JPEG_MAST_ENB BIT(7) #define TW5864_AU_MAST_ENB_CHN_SHIFT 8 /* audio master channel enable */ #define TW5864_AU_MAST_ENB_CHN (0xffff << 8) /* IIC interrupt enable */ #define TW5864_IIC_INTR_ENB BIT(24) /* ad interrupt enable */ #define TW5864_AD_INTR_ENB BIT(25) /* target burst enable */ #define TW5864_PCI_TAR_BURST_ENB BIT(26) /* vlc stream burst enable */ #define TW5864_PCI_VLC_BURST_ENB BIT(27) /* ddr burst enable (1 enable, and must set DDR_BRST_EN) */ #define TW5864_PCI_DDR_BURST_ENB BIT(28) /* * Because preview and audio have 16 channels separately, so using this * registers to indicate interrupt status for every channels. This is secondary * interrupt status register. OR operating of the PREV_INTR_REG is * PREV_EOF_INTR, OR operating of the AU_INTR_REG bits is AUDIO_EOF_INTR */ #define TW5864_PREV_AND_AU_INTR 0x18008 /* Define controls in register TW5864_PREV_AND_AU_INTR */ /* preview eof interrupt flag */ #define TW5864_PREV_INTR_REG 0x0000ffff #define TW5864_AU_INTR_REG_SHIFT 16 /* audio eof interrupt flag */ #define TW5864_AU_INTR_REG (0xffff << 16) #define TW5864_MASTER_ENB_REG 0x1800c /* Define controls in register TW5864_MASTER_ENB_REG */ /* master enable */ #define TW5864_PCI_VLC_INTR_ENB BIT(1) /* mvd and vlc master enable */ #define TW5864_PCI_PREV_INTR_ENB BIT(4) /* ad vsync master enable */ #define TW5864_PCI_PREV_OF_INTR_ENB BIT(5) /* jpeg master enable */ #define TW5864_PCI_JPEG_INTR_ENB BIT(7) /* preview master enable */ #define TW5864_PCI_AUD_INTR_ENB BIT(8) /* * Every channel of preview and audio have ping-pong buffers in system memory, * this register is the buffer flag to notify software which buffer is been * operated. */ #define TW5864_PREV_AND_AU_BUF_FLAG 0x18010 /* Define controls in register TW5864_PREV_AND_AU_BUF_FLAG */ /* preview buffer A/B flag */ #define TW5864_PREV_BUF_FLAG 0xffff #define TW5864_AUDIO_BUF_FLAG_SHIFT 16 /* audio buffer A/B flag */ #define TW5864_AUDIO_BUF_FLAG (0xffff << 16) #define TW5864_IIC 0x18014 /* Define controls in register TW5864_IIC */ /* register data */ #define TW5864_IIC_DATA 0x00ff #define TW5864_IIC_REG_ADDR_SHIFT 8 /* register addr */ #define TW5864_IIC_REG_ADDR (0xff << 8) /* rd/wr flag rd=1,wr=0 */ #define TW5864_IIC_RW BIT(16) #define TW5864_IIC_DEV_ADDR_SHIFT 17 /* device addr */ #define TW5864_IIC_DEV_ADDR (0x7f << 17) /* * iic done, software kick off one time iic transaction through setting this * bit to 1. Then poll this bit, value 1 indicate iic transaction have * completed, if read, valid data have been stored in iic_data */ #define TW5864_IIC_DONE BIT(24) #define TW5864_RST_AND_IF_INFO 0x18018 /* Define controls in register TW5864_RST_AND_IF_INFO */ /* application software soft reset */ #define TW5864_APP_SOFT_RST BIT(0) #define TW5864_PCI_INF_VERSION_SHIFT 16 /* PCI interface version, read only */ #define TW5864_PCI_INF_VERSION (0xffff << 16) /* vlc stream crc value, it is calculated in pci module */ #define TW5864_VLC_CRC_REG 0x1801c /* * vlc max length, it is defined by software based on software assign memory * space for vlc */ #define TW5864_VLC_MAX_LENGTH 0x18020 /* vlc length of one frame */ #define TW5864_VLC_LENGTH 0x18024 /* vlc original crc value */ #define TW5864_VLC_INTRA_CRC_I_REG 0x18028 /* vlc original crc value */ #define TW5864_VLC_INTRA_CRC_O_REG 0x1802c /* mv stream crc value, it is calculated in pci module */ #define TW5864_VLC_PAR_CRC_REG 0x18030 /* mv length */ #define TW5864_VLC_PAR_LENGTH_REG 0x18034 /* mv original crc value */ #define TW5864_VLC_PAR_I_REG 0x18038 /* mv original crc value */ #define TW5864_VLC_PAR_O_REG 0x1803c /* * Configuration register for 9[or 10] CIFs or 1D1+15QCIF Preview mode. * PREV_PCI_ENB_CHN[0] Enable 9th preview channel (9CIF prev) or 1D1 channel in * (1D1+15QCIF prev) * PREV_PCI_ENB_CHN[1] Enable 10th preview channel */ #define TW5864_PREV_PCI_ENB_CHN 0x18040 /* Description skipped. */ #define TW5864_PREV_FRAME_FORMAT_IN 0x18044 /* IIC enable */ #define TW5864_IIC_ENB 0x18048 /* * Timer interrupt interval * 0 1ms * 1 2ms * 2 4ms * 3 8ms */ #define TW5864_PCI_INTTM_SCALE 0x1804c /* * The above register is pci base address registers. Application software will * initialize them to tell chip where the corresponding stream will be dumped * to. Application software will select appropriate base address interval based * on the stream length. */ /* VLC stream base address */ #define TW5864_VLC_STREAM_BASE_ADDR 0x18080 /* MV stream base address */ #define TW5864_MV_STREAM_BASE_ADDR 0x18084 /* 0x180a0 ~ 0x180bc: audio burst base address. Skipped. */ /* 0x180c0 ~ 0x180dc: JPEG Push Mode Buffer Base Address. Skipped. */ /* 0x18100 ~ 0x1817c: preview burst base address. Skipped. */ /* 0x80000 ~ 0x87fff - DDR Burst RW Register Map */ #define TW5864_DDR_CTL 0x80000 /* Define controls in register TW5864_DDR_CTL */ #define TW5864_BRST_LENGTH_SHIFT 2 /* Length of 32-bit data burst */ #define TW5864_BRST_LENGTH (0x3fff << 2) /* * Burst Read/Write * 0 Read Burst from DDR * 1 Write Burst to DDR */ #define TW5864_BRST_RW BIT(16) /* Begin a new DDR Burst. This bit is self cleared */ #define TW5864_NEW_BRST_CMD BIT(17) /* DDR Burst End Flag */ #define TW5864_BRST_END BIT(24) /* Enable Error Interrupt for Single DDR Access */ #define TW5864_SING_ERR_INTR BIT(25) /* Enable Error Interrupt for Burst DDR Access */ #define TW5864_BRST_ERR_INTR BIT(26) /* Enable Interrupt for End of DDR Burst Access */ #define TW5864_BRST_END_INTR BIT(27) /* DDR Single Access Error Flag */ #define TW5864_SINGLE_ERR BIT(28) /* DDR Single Access Busy Flag */ #define TW5864_SINGLE_BUSY BIT(29) /* DDR Burst Access Error Flag */ #define TW5864_BRST_ERR BIT(30) /* DDR Burst Access Busy Flag */ #define TW5864_BRST_BUSY BIT(31) /* [27:0] DDR Access Address. Bit [1:0] has to be 0 */ #define TW5864_DDR_ADDR 0x80004 /* DDR Access Internal Buffer Address. Bit [1:0] has to be 0 */ #define TW5864_DPR_BUF_ADDR 0x80008 /* SRAM Buffer MPI Access Space. Totally 16 KB */ #define TW5864_DPR_BUF_START 0x84000 /* 0x84000 - 0x87ffc */ #define TW5864_DPR_BUF_SIZE 0x4000 /* Indirect Map Space */ /* * The indirect space is accessed through 0xb800 ~ 0xb807 registers in direct * access space */ /* Analog Video / Audio Decoder / Encoder */ /* Allowed channel values: [0; 3] */ /* Read-only register */ #define TW5864_INDIR_VIN_0(channel) (0x000 + channel * 0x010) /* Define controls in register TW5864_INDIR_VIN_0 */ /* * 1 Video not present. (sync is not detected in number of consecutive line * periods specified by MISSCNT register) * 0 Video detected. */ #define TW5864_INDIR_VIN_0_VDLOSS BIT(7) /* * 1 Horizontal sync PLL is locked to the incoming video source. * 0 Horizontal sync PLL is not locked. */ #define TW5864_INDIR_VIN_0_HLOCK BIT(6) /* * 1 Sub-carrier PLL is locked to the incoming video source. * 0 Sub-carrier PLL is not locked. */ #define TW5864_INDIR_VIN_0_SLOCK BIT(5) /* * 1 Even field is being decoded. * 0 Odd field is being decoded. */ #define TW5864_INDIR_VIN_0_FLD BIT(4) /* * 1 Vertical logic is locked to the incoming video source. * 0 Vertical logic is not locked. */ #define TW5864_INDIR_VIN_0_VLOCK BIT(3) /* * 1 No color burst signal detected. * 0 Color burst signal detected. */ #define TW5864_INDIR_VIN_0_MONO BIT(1) /* * 0 60Hz source detected * 1 50Hz source detected * The actual vertical scanning frequency depends on the current standard * invoked. */ #define TW5864_INDIR_VIN_0_DET50 BIT(0) #define TW5864_INDIR_VIN_1(channel) (0x001 + channel * 0x010) /* VCR signal indicator. Read-only. */ #define TW5864_INDIR_VIN_1_VCR BIT(7) /* Weak signal indicator 2. Read-only. */ #define TW5864_INDIR_VIN_1_WKAIR BIT(6) /* Weak signal indicator controlled by WKTH. Read-only. */ #define TW5864_INDIR_VIN_1_WKAIR1 BIT(5) /* * 1 = Standard signal * 0 = Non-standard signal * Read-only */ #define TW5864_INDIR_VIN_1_VSTD BIT(4) /* * 1 = Non-interlaced signal * 0 = interlaced signal * Read-only */ #define TW5864_INDIR_VIN_1_NINTL BIT(3) /* * Vertical Sharpness Control. Writable. * 0 = None (default) * 7 = Highest * **Note: VSHP must be set to '0' if COMB = 0 */ #define TW5864_INDIR_VIN_1_VSHP 0x07 /* HDELAY_XY[7:0] */ #define TW5864_INDIR_VIN_2_HDELAY_XY_LO(channel) (0x002 + channel * 0x010) /* HACTIVE_XY[7:0] */ #define TW5864_INDIR_VIN_3_HACTIVE_XY_LO(channel) (0x003 + channel * 0x010) /* VDELAY_XY[7:0] */ #define TW5864_INDIR_VIN_4_VDELAY_XY_LO(channel) (0x004 + channel * 0x010) /* VACTIVE_XY[7:0] */ #define TW5864_INDIR_VIN_5_VACTIVE_XY_LO(channel) (0x005 + channel * 0x010) #define TW5864_INDIR_VIN_6(channel) (0x006 + channel * 0x010) /* Define controls in register TW5864_INDIR_VIN_6 */ #define TW5864_INDIR_VIN_6_HDELAY_XY_HI 0x03 #define TW5864_INDIR_VIN_6_HACTIVE_XY_HI_SHIFT 2 #define TW5864_INDIR_VIN_6_HACTIVE_XY_HI (0x03 << 2) #define TW5864_INDIR_VIN_6_VDELAY_XY_HI BIT(4) #define TW5864_INDIR_VIN_6_VACTIVE_XY_HI BIT(5) /* * HDELAY_XY This 10bit register defines the starting location of horizontal * active pixel for display / record path. A unit is 1 pixel. The default value * is 0x00f for NTSC and 0x00a for PAL. * * HACTIVE_XY This 10bit register defines the number of horizontal active pixel * for display / record path. A unit is 1 pixel. The default value is decimal * 720. * * VDELAY_XY This 9bit register defines the starting location of vertical * active for display / record path. A unit is 1 line. The default value is * decimal 6. * * VACTIVE_XY This 9bit register defines the number of vertical active lines * for display / record path. A unit is 1 line. The default value is decimal * 240. */ /* HUE These bits control the color hue as 2's complement number. They have * value from +36o (7Fh) to -36o (80h) with an increment of 2.8o. The 2 LSB has * no effect. The positive value gives greenish tone and negative value gives * purplish tone. The default value is 0o (00h). This is effective only on NTSC * system. The default is 00h. */ #define TW5864_INDIR_VIN_7_HUE(channel) (0x007 + channel * 0x010) #define TW5864_INDIR_VIN_8(channel) (0x008 + channel * 0x010) /* Define controls in register TW5864_INDIR_VIN_8 */ /* * This bit controls the center frequency of the peaking filter. * The corresponding gain adjustment is HFLT. * 0 Low * 1 center */ #define TW5864_INDIR_VIN_8_SCURVE BIT(7) /* CTI level selection. The default is 1. * 0 None * 3 Highest */ #define TW5864_INDIR_VIN_8_CTI_SHIFT 4 #define TW5864_INDIR_VIN_8_CTI (0x03 << 4) /* * These bits control the amount of sharpness enhancement on the luminance * signals. There are 16 levels of control with "0" having no effect on the * output image. 1 through 15 provides sharpness enhancement with "F" being the * strongest. The default is 1. */ #define TW5864_INDIR_VIN_8_SHARPNESS 0x0f /* * These bits control the luminance contrast gain. A value of 100 (64h) has a * gain of 1. The range adjustment is from 0% to 255% at 1% per step. The * default is 64h. */ #define TW5864_INDIR_VIN_9_CNTRST(channel) (0x009 + channel * 0x010) /* * These bits control the brightness. They have value of -128 to 127 in 2's * complement form. Positive value increases brightness. A value 0 has no * effect on the data. The default is 00h. */ #define TW5864_INDIR_VIN_A_BRIGHT(channel) (0x00a + channel * 0x010) /* * These bits control the digital gain adjustment to the U (or Cb) component of * the digital video signal. The color saturation can be adjusted by adjusting * the U and V color gain components by the same amount in the normal * situation. The U and V can also be adjusted independently to provide greater * flexibility. The range of adjustment is 0 to 200%. A value of 128 (80h) has * gain of 100%. The default is 80h. */ #define TW5864_INDIR_VIN_B_SAT_U(channel) (0x00b + channel * 0x010) /* * These bits control the digital gain adjustment to the V (or Cr) component of * the digital video signal. The color saturation can be adjusted by adjusting * the U and V color gain components by the same amount in the normal * situation. The U and V can also be adjusted independently to provide greater * flexibility. The range of adjustment is 0 to 200%. A value of 128 (80h) has * gain of 100%. The default is 80h. */ #define TW5864_INDIR_VIN_C_SAT_V(channel) (0x00c + channel * 0x010) /* Read-only */ #define TW5864_INDIR_VIN_D(channel) (0x00d + channel * 0x010) /* Define controls in register TW5864_INDIR_VIN_D */ /* Macrovision color stripe detection may be un-reliable */ #define TW5864_INDIR_VIN_D_CSBAD BIT(3) /* Macrovision AGC pulse detected */ #define TW5864_INDIR_VIN_D_MCVSN BIT(2) /* Macrovision color stripe protection burst detected */ #define TW5864_INDIR_VIN_D_CSTRIPE BIT(1) /* * This bit is valid only when color stripe protection is detected, i.e. if * CSTRIPE=1, * 1 Type 2 color stripe protection * 0 Type 3 color stripe protection */ #define TW5864_INDIR_VIN_D_CTYPE2 BIT(0) /* Read-only */ #define TW5864_INDIR_VIN_E(channel) (0x00e + channel * 0x010) /* Define controls in register TW5864_INDIR_VIN_E */ /* * Read-only. * 0 Idle * 1 Detection in progress */ #define TW5864_INDIR_VIN_E_DETSTUS BIT(7) /* * STDNOW Current standard invoked * 0 NTSC (M) * 1 PAL (B, D, G, H, I) * 2 SECAM * 3 NTSC4.43 * 4 PAL (M) * 5 PAL (CN) * 6 PAL 60 * 7 Not valid */ #define TW5864_INDIR_VIN_E_STDNOW_SHIFT 4 #define TW5864_INDIR_VIN_E_STDNOW (0x07 << 4) /* * 1 Disable the shadow registers * 0 Enable VACTIVE and HDELAY shadow registers value depending on STANDARD. * (Default) */ #define TW5864_INDIR_VIN_E_ATREG BIT(3) /* * STANDARD Standard selection * 0 NTSC (M) * 1 PAL (B, D, G, H, I) * 2 SECAM * 3 NTSC4.43 * 4 PAL (M) * 5 PAL (CN) * 6 PAL 60 * 7 Auto detection (Default) */ #define TW5864_INDIR_VIN_E_STANDARD 0x07 #define TW5864_INDIR_VIN_F(channel) (0x00f + channel * 0x010) /* Define controls in register TW5864_INDIR_VIN_F */ /* * 1 Writing 1 to this bit will manually initiate the auto format detection * process. This bit is a self-clearing bit * 0 Manual initiation of auto format detection is done. (Default) */ #define TW5864_INDIR_VIN_F_ATSTART BIT(7) /* Enable recognition of PAL60 (Default) */ #define TW5864_INDIR_VIN_F_PAL60EN BIT(6) /* Enable recognition of PAL (CN). (Default) */ #define TW5864_INDIR_VIN_F_PALCNEN BIT(5) /* Enable recognition of PAL (M). (Default) */ #define TW5864_INDIR_VIN_F_PALMEN BIT(4) /* Enable recognition of NTSC 4.43. (Default) */ #define TW5864_INDIR_VIN_F_NTSC44EN BIT(3) /* Enable recognition of SECAM. (Default) */ #define TW5864_INDIR_VIN_F_SECAMEN BIT(2) /* Enable recognition of PAL (B, D, G, H, I). (Default) */ #define TW5864_INDIR_VIN_F_PALBEN BIT(1) /* Enable recognition of NTSC (M). (Default) */ #define TW5864_INDIR_VIN_F_NTSCEN BIT(0) /* Some registers skipped. */ /* Use falling edge to sample VD1-VD4 from 54 MHz to 108 MHz */ #define TW5864_INDIR_VD_108_POL 0x041 #define TW5864_INDIR_VD_108_POL_VD12 BIT(0) #define TW5864_INDIR_VD_108_POL_VD34 BIT(1) #define TW5864_INDIR_VD_108_POL_BOTH \ (TW5864_INDIR_VD_108_POL_VD12 | TW5864_INDIR_VD_108_POL_VD34) /* Some registers skipped. */ /* * Audio Input ADC gain control * 0 0.25 * 1 0.31 * 2 0.38 * 3 0.44 * 4 0.50 * 5 0.63 * 6 0.75 * 7 0.88 * 8 1.00 (default) * 9 1.25 * 10 1.50 * 11 1.75 * 12 2.00 * 13 2.25 * 14 2.50 * 15 2.75 */ /* [3:0] channel 0, [7:4] channel 1 */ #define TW5864_INDIR_AIGAIN1 0x060 /* [3:0] channel 2, [7:4] channel 3 */ #define TW5864_INDIR_AIGAIN2 0x061 /* Some registers skipped */ #define TW5864_INDIR_AIN_0x06D 0x06d /* Define controls in register TW5864_INDIR_AIN_0x06D */ /* * LAWMD Select u-Law/A-Law/PCM/SB data output format on ADATR and ADATM pin. * 0 PCM output (default) * 1 SB (Signed MSB bit in PCM data is inverted) output * 2 u-Law output * 3 A-Law output */ #define TW5864_INDIR_AIN_LAWMD_SHIFT 6 #define TW5864_INDIR_AIN_LAWMD (0x03 << 6) /* * Disable the mixing ratio value for all audio. * 0 Apply individual mixing ratio value for each audio (default) * 1 Apply nominal value for all audio commonly */ #define TW5864_INDIR_AIN_MIX_DERATIO BIT(5) /* * Enable the mute function for audio channel AINn when n is 0 to 3. It effects * only for mixing. When n = 4, it enable the mute function of the playback * audio input. It effects only for single chip or the last stage chip * 0 Normal * 1 Muted (default) */ #define TW5864_INDIR_AIN_MIX_MUTE 0x1f /* Some registers skipped */ #define TW5864_INDIR_AIN_0x0E3 0x0e3 /* Define controls in register TW5864_INDIR_AIN_0x0E3 */ /* * ADATP signal is coming from external ADPCM decoder, instead of on-chip ADPCM * decoder */ #define TW5864_INDIR_AIN_0x0E3_EXT_ADATP BIT(7) /* ACLKP output signal polarity inverse */ #define TW5864_INDIR_AIN_0x0E3_ACLKPPOLO BIT(6) /* * ACLKR input signal polarity inverse. * 0 Not inversed (Default) * 1 Inversed */ #define TW5864_INDIR_AIN_0x0E3_ACLKRPOL BIT(5) /* * ACLKP input signal polarity inverse. * 0 Not inversed (Default) * 1 Inversed */ #define TW5864_INDIR_AIN_0x0E3_ACLKPPOLI BIT(4) /* * ACKI [21:0] control automatic set up with AFMD registers * This mode is only effective when ACLKRMASTER=1 * 0 ACKI [21:0] registers set up ACKI control * 1 ACKI control is automatically set up by AFMD register values */ #define TW5864_INDIR_AIN_0x0E3_AFAUTO BIT(3) /* * AFAUTO control mode * 0 8kHz setting (Default) * 1 16kHz setting * 2 32kHz setting * 3 44.1kHz setting * 4 48kHz setting */ #define TW5864_INDIR_AIN_0x0E3_AFMD 0x07 #define TW5864_INDIR_AIN_0x0E4 0x0e4 /* Define controls in register TW5864_INDIR_AIN_0x0ED */ /* * 8bit I2S Record output mode. * 0 L/R half length separated output (Default). * 1 One continuous packed output equal to DSP output format. */ #define TW5864_INDIR_AIN_0x0E4_I2S8MODE BIT(7) /* * Audio Clock Master ACLKR output wave format. * 0 High periods is one 27MHz clock period (default). * 1 Almost duty 50-50% clock output on ACLKR pin. If this mode is selected, two * times bigger number value need to be set up on the ACKI register. If * AFAUTO=1, ACKI control is automatically set up even if MASCKMD=1. */ #define TW5864_INDIR_AIN_0x0E4_MASCKMD BIT(6) /* Playback ACLKP/ASYNP/ADATP input data MSB-LSB swapping */ #define TW5864_INDIR_AIN_0x0E4_PBINSWAP BIT(5) /* * ASYNR input signal delay. * 0 No delay * 1 Add one 27MHz period delay in ASYNR signal input */ #define TW5864_INDIR_AIN_0x0E4_ASYNRDLY BIT(4) /* * ASYNP input signal delay. * 0 no delay * 1 add one 27MHz period delay in ASYNP signal input */ #define TW5864_INDIR_AIN_0x0E4_ASYNPDLY BIT(3) /* * ADATP input data delay by one ACLKP clock. * 0 No delay (Default). This is for I2S type 1T delay input interface. * 1 Add 1 ACLKP clock delay in ADATP input data. This is for left-justified * type 0T delay input interface. */ #define TW5864_INDIR_AIN_0x0E4_ADATPDLY BIT(2) /* * Select u-Law/A-Law/PCM/SB data input format on ADATP pin. * 0 PCM input (Default) * 1 SB (Signed MSB bit in PCM data is inverted) input * 2 u-Law input * 3 A-Law input */ #define TW5864_INDIR_AIN_0x0E4_INLAWMD 0x03 /* * Enable state register updating and interrupt request of audio AIN5 detection * for each input */ #define TW5864_INDIR_AIN_A5DETENA 0x0e5 /* Some registers skipped */ /* * [7:3]: DEV_ID The TW5864 product ID code is 01000 * [2:0]: REV_ID The revision number is 0h */ #define TW5864_INDIR_ID 0x0fe #define TW5864_INDIR_IN_PIC_WIDTH(channel) (0x200 + 4 * channel) #define TW5864_INDIR_IN_PIC_HEIGHT(channel) (0x201 + 4 * channel) #define TW5864_INDIR_OUT_PIC_WIDTH(channel) (0x202 + 4 * channel) #define TW5864_INDIR_OUT_PIC_HEIGHT(channel) (0x203 + 4 * channel) /* Some registers skipped */ #define TW5864_INDIR_CROP_ETC 0x260 /* Define controls in register TW5864_INDIR_CROP_ETC */ /* Enable cropping from 720 to 704 */ #define TW5864_INDIR_CROP_ETC_CROP_EN 0x4 /* * Interrupt status register from the front-end. Write "1" to each bit to clear * the interrupt * 15:0 Motion detection interrupt for channel 0 ~ 15 * 31:16 Night detection interrupt for channel 0 ~ 15 * 47:32 Blind detection interrupt for channel 0 ~ 15 * 63:48 No video interrupt for channel 0 ~ 15 * 79:64 Line mode underflow interrupt for channel 0 ~ 15 * 95:80 Line mode overflow interrupt for channel 0 ~ 15 */ /* 0x2d0~0x2d7: [63:0] bits */ #define TW5864_INDIR_INTERRUPT1 0x2d0 /* 0x2e0~0x2e3: [95:64] bits */ #define TW5864_INDIR_INTERRUPT2 0x2e0 /* * Interrupt mask register for interrupts in 0x2d0 ~ 0x2d7 * 15:0 Motion detection interrupt for channel 0 ~ 15 * 31:16 Night detection interrupt for channel 0 ~ 15 * 47:32 Blind detection interrupt for channel 0 ~ 15 * 63:48 No video interrupt for channel 0 ~ 15 * 79:64 Line mode underflow interrupt for channel 0 ~ 15 * 95:80 Line mode overflow interrupt for channel 0 ~ 15 */ /* 0x2d8~0x2df: [63:0] bits */ #define TW5864_INDIR_INTERRUPT_MASK1 0x2d8 /* 0x2e8~0x2eb: [95:64] bits */ #define TW5864_INDIR_INTERRUPT_MASK2 0x2e8 /* [11:0]: Interrupt summary register for interrupts & interrupt mask from in * 0x2d0 ~ 0x2d7 and 0x2d8 ~ 0x2df * bit 0: interrupt occurs in 0x2d0 & 0x2d8 * bit 1: interrupt occurs in 0x2d1 & 0x2d9 * bit 2: interrupt occurs in 0x2d2 & 0x2da * bit 3: interrupt occurs in 0x2d3 & 0x2db * bit 4: interrupt occurs in 0x2d4 & 0x2dc * bit 5: interrupt occurs in 0x2d5 & 0x2dd * bit 6: interrupt occurs in 0x2d6 & 0x2de * bit 7: interrupt occurs in 0x2d7 & 0x2df * bit 8: interrupt occurs in 0x2e0 & 0x2e8 * bit 9: interrupt occurs in 0x2e1 & 0x2e9 * bit 10: interrupt occurs in 0x2e2 & 0x2ea * bit 11: interrupt occurs in 0x2e3 & 0x2eb */ #define TW5864_INDIR_INTERRUPT_SUMMARY 0x2f0 /* Motion / Blind / Night Detection */ /* valid value for channel is [0:15] */ #define TW5864_INDIR_DETECTION_CTL0(channel) (0x300 + channel * 0x08) /* Define controls in register TW5864_INDIR_DETECTION_CTL0 */ /* * Disable the motion and blind detection. * 0 Enable motion and blind detection (default) * 1 Disable motion and blind detection */ #define TW5864_INDIR_DETECTION_CTL0_MD_DIS BIT(5) /* * Request to start motion detection on manual trigger mode * 0 None Operation (default) * 1 Request to start motion detection */ #define TW5864_INDIR_DETECTION_CTL0_MD_STRB BIT(3) /* * Select the trigger mode of motion detection * 0 Automatic trigger mode of motion detection (default) * 1 Manual trigger mode for motion detection */ #define TW5864_INDIR_DETECTION_CTL0_MD_STRB_EN BIT(2) /* * Define the threshold of cell for blind detection. * 0 Low threshold (More sensitive) (default) * : : * 3 High threshold (Less sensitive) */ #define TW5864_INDIR_DETECTION_CTL0_BD_CELSENS 0x03 #define TW5864_INDIR_DETECTION_CTL1(channel) (0x301 + channel * 0x08) /* Define controls in register TW5864_INDIR_DETECTION_CTL1 */ /* * Control the temporal sensitivity of motion detector. * 0 More Sensitive (default) * : : * 15 Less Sensitive */ #define TW5864_INDIR_DETECTION_CTL1_MD_TMPSENS_SHIFT 4 #define TW5864_INDIR_DETECTION_CTL1_MD_TMPSENS (0x0f << 4) /* * Adjust the horizontal starting position for motion detection * 0 0 pixel (default) * : : * 15 15 pixels */ #define TW5864_INDIR_DETECTION_CTL1_MD_PIXEL_OS 0x0f #define TW5864_INDIR_DETECTION_CTL2(channel) (0x302 + channel * 0x08) /* Define controls in register TW5864_INDIR_DETECTION_CTL2 */ /* * Control the updating time of reference field for motion detection. * 0 Update reference field every field (default) * 1 Update reference field according to MD_SPEED */ #define TW5864_INDIR_DETECTION_CTL2_MD_REFFLD BIT(7) /* * Select the field for motion detection. * 0 Detecting motion for only odd field (default) * 1 Detecting motion for only even field * 2 Detecting motion for any field * 3 Detecting motion for both odd and even field */ #define TW5864_INDIR_DETECTION_CTL2_MD_FIELD_SHIFT 5 #define TW5864_INDIR_DETECTION_CTL2_MD_FIELD (0x03 << 5) /* * Control the level sensitivity of motion detector. * 0 More sensitive (default) * : : * 15 Less sensitive */ #define TW5864_INDIR_DETECTION_CTL2_MD_LVSENS 0x1f #define TW5864_INDIR_DETECTION_CTL3(channel) (0x303 + channel * 0x08) /* Define controls in register TW5864_INDIR_DETECTION_CTL3 */ /* * Define the threshold of sub-cell number for motion detection. * 0 Motion is detected if 1 sub-cell has motion (More sensitive) (default) * 1 Motion is detected if 2 sub-cells have motion * 2 Motion is detected if 3 sub-cells have motion * 3 Motion is detected if 4 sub-cells have motion (Less sensitive) */ #define TW5864_INDIR_DETECTION_CTL3_MD_CELSENS_SHIFT 6 #define TW5864_INDIR_DETECTION_CTL3_MD_CELSENS (0x03 << 6) /* * Control the velocity of motion detector. * Large value is suitable for slow motion detection. * In MD_DUAL_EN = 1, MD_SPEED should be limited to 0 ~ 31. * 0 1 field intervals (default) * 1 2 field intervals * : : * 61 62 field intervals * 62 63 field intervals * 63 Not supported */ #define TW5864_INDIR_DETECTION_CTL3_MD_SPEED 0x3f #define TW5864_INDIR_DETECTION_CTL4(channel) (0x304 + channel * 0x08) /* Define controls in register TW5864_INDIR_DETECTION_CTL4 */ /* * Control the spatial sensitivity of motion detector. * 0 More Sensitive (default) * : : * 15 Less Sensitive */ #define TW5864_INDIR_DETECTION_CTL4_MD_SPSENS_SHIFT 4 #define TW5864_INDIR_DETECTION_CTL4_MD_SPSENS (0x0f << 4) /* * Define the threshold of level for blind detection. * 0 Low threshold (More sensitive) (default) * : : * 15 High threshold (Less sensitive) */ #define TW5864_INDIR_DETECTION_CTL4_BD_LVSENS 0x0f #define TW5864_INDIR_DETECTION_CTL5(channel) (0x305 + channel * 0x08) /* * Define the threshold of temporal sensitivity for night detection. * 0 Low threshold (More sensitive) (default) * : : * 15 High threshold (Less sensitive) */ #define TW5864_INDIR_DETECTION_CTL5_ND_TMPSENS_SHIFT 4 #define TW5864_INDIR_DETECTION_CTL5_ND_TMPSENS (0x0f << 4) /* * Define the threshold of level for night detection. * 0 Low threshold (More sensitive) (default) * : : * 3 High threshold (Less sensitive) */ #define TW5864_INDIR_DETECTION_CTL5_ND_LVSENS 0x0f /* * [11:0] The base address of the motion detection buffer. This address is in * unit of 64K bytes. The generated DDR address will be {MD_BASE_ADDR, * 16"h0000}. The default value should be 12"h000 */ #define TW5864_INDIR_MD_BASE_ADDR 0x380 /* * This controls the channel of the motion detection result shown in register * 0x3a0 ~ 0x3b7. Before reading back motion result, always set this first. */ #define TW5864_INDIR_RGR_MOTION_SEL 0x382 /* [15:0] MD strobe has been performed at channel n (read only) */ #define TW5864_INDIR_MD_STRB 0x386 /* NO_VIDEO Detected from channel n (read only) */ #define TW5864_INDIR_NOVID_DET 0x388 /* Motion Detected from channel n (read only) */ #define TW5864_INDIR_MD_DET 0x38a /* Blind Detected from channel n (read only) */ #define TW5864_INDIR_BD_DET 0x38c /* Night Detected from channel n (read only) */ #define TW5864_INDIR_ND_DET 0x38e /* 192 bit motion flag of the channel specified by RGR_MOTION_SEL in 0x382 */ #define TW5864_INDIR_MOTION_FLAG 0x3a0 #define TW5864_INDIR_MOTION_FLAG_BYTE_COUNT 24 /* * [9:0] The motion cell count of a specific channel selected by 0x382. This is * for DI purpose */ #define TW5864_INDIR_MD_DI_CNT 0x3b8 /* The motion detection cell sensitivity for DI purpose */ #define TW5864_INDIR_MD_DI_CELLSENS 0x3ba /* The motion detection threshold level for DI purpose */ #define TW5864_INDIR_MD_DI_LVSENS 0x3bb /* 192 bit motion mask of the channel specified by MASK_CH_SEL in 0x3fe */ #define TW5864_INDIR_MOTION_MASK 0x3e0 #define TW5864_INDIR_MOTION_MASK_BYTE_COUNT 24 /* [4:0] The channel selection to access masks in 0x3e0 ~ 0x3f7 */ #define TW5864_INDIR_MASK_CH_SEL 0x3fe /* Clock PLL / Analog IP Control */ /* Some registers skipped */ #define TW5864_INDIR_DDRA_DLL_DQS_SEL0 0xee6 #define TW5864_INDIR_DDRA_DLL_DQS_SEL1 0xee7 #define TW5864_INDIR_DDRA_DLL_CLK90_SEL 0xee8 #define TW5864_INDIR_DDRA_DLL_TEST_SEL_AND_TAP_S 0xee9 #define TW5864_INDIR_DDRB_DLL_DQS_SEL0 0xeeb #define TW5864_INDIR_DDRB_DLL_DQS_SEL1 0xeec #define TW5864_INDIR_DDRB_DLL_CLK90_SEL 0xeed #define TW5864_INDIR_DDRB_DLL_TEST_SEL_AND_TAP_S 0xeee #define TW5864_INDIR_RESET 0xef0 #define TW5864_INDIR_RESET_VD BIT(7) #define TW5864_INDIR_RESET_DLL BIT(6) #define TW5864_INDIR_RESET_MUX_CORE BIT(5) #define TW5864_INDIR_PV_VD_CK_POL 0xefd #define TW5864_INDIR_PV_VD_CK_POL_PV(channel) BIT(channel) #define TW5864_INDIR_PV_VD_CK_POL_VD(channel) BIT(channel + 4) #define TW5864_INDIR_CLK0_SEL 0xefe #define TW5864_INDIR_CLK0_SEL_VD_SHIFT 0 #define TW5864_INDIR_CLK0_SEL_VD_MASK 0x3 #define TW5864_INDIR_CLK0_SEL_PV_SHIFT 2 #define TW5864_INDIR_CLK0_SEL_PV_MASK (0x3 << 2) #define TW5864_INDIR_CLK0_SEL_PV2_SHIFT 4 #define TW5864_INDIR_CLK0_SEL_PV2_MASK (0x3 << 4)