// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
*/
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "sdm845.dtsi"
#include "pm8005.dtsi"
#include "pm8998.dtsi"
#include "pmi8998.dtsi"
/ {
qcom,msm-id = <321 0x20001>; /* SDM845 v2.1 */
qcom,board-id = <8 0>;
aliases {
serial0 = &uart6;
serial1 = &uart9;
};
chosen {
stdout-path = "serial0:115200n8";
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-0 = <&focus_n &snapshot_n &vol_down_n &vol_up_n>;
pinctrl-names = "default";
key-camera-focus {
label = "Camera Focus";
gpios = <&pm8998_gpios 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_CAMERA_FOCUS>;
debounce-interval = <15>;
linux,can-disable;
wakeup-source;
};
key-camera-snapshot {
label = "Camera Snapshot";
gpios = <&pm8998_gpios 7 GPIO_ACTIVE_LOW>;
linux,code = <KEY_CAMERA>;
debounce-interval = <15>;
linux,can-disable;
wakeup-source;
};
key-volume-down {
label = "Volume Down";
gpios = <&pm8998_gpios 5 GPIO_ACTIVE_LOW>;
linux,code = <KEY_VOLUMEDOWN>;
debounce-interval = <15>;
linux,can-disable;
wakeup-source;
};
key-volume-up {
label = "Volume Up";
gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>;
linux,code = <KEY_VOLUMEUP>;
debounce-interval = <15>;
linux,can-disable;
wakeup-source;
};
};
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
regulator-min-microvolt = <3700000>;
regulator-max-microvolt = <3700000>;
};
vreg_s4a_1p8: pm8998-smps4 {
compatible = "regulator-fixed";
regulator-name = "vreg_s4a_1p8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&vph_pwr>;
};
reserved-memory {
/* SONY was cool and didn't diverge from MTP this time, yay! */
cont_splash_mem: memory@9d400000 {
reg = <0x0 0x9d400000 0x0 0x2400000>;
no-map;
};
ramoops@ffc00000 {
compatible = "ramoops";
reg = <0x0 0xffc00000 0x0 0x100000>;
record-size = <0x10000>;
console-size = <0x60000>;
ftrace-size = <0x10000>;
pmsg-size = <0x20000>;
ecc-size = <16>;
no-map;
};
};
};
&adsp_pas {
firmware-name = "qcom/sdm845/Sony/tama/adsp.mbn";
status = "okay";
};
&apps_rsc {
regulators-0 {
compatible = "qcom,pm8998-rpmh-regulators";
qcom,pmic-id = "a";
vdd-s1-supply = <&vph_pwr>;
vdd-s2-supply = <&vph_pwr>;
vdd-s3-supply = <&vph_pwr>;
vdd-s4-supply = <&vph_pwr>;
vdd-s5-supply = <&vph_pwr>;
vdd-s6-supply = <&vph_pwr>;
vdd-s7-supply = <&vph_pwr>;
vdd-s8-supply = <&vph_pwr>;
vdd-s9-supply = <&vph_pwr>;
vdd-s10-supply = <&vph_pwr>;
vdd-s11-supply = <&vph_pwr>;
vdd-s12-supply = <&vph_pwr>;
vdd-s13-supply = <&vph_pwr>;
vdd-l1-l27-supply = <&vreg_s7a_0p9>;
vdd-l2-l8-l17-supply = <&vreg_s3a_1p3>;
vdd-l3-l11-supply = <&vreg_s7a_0p9>;
vdd-l4-l5-supply = <&vreg_s7a_0p9>;
vdd-l6-supply = <&vph_pwr>;
vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>;
vdd-l9-supply = <&vreg_s5a_1p9>;
vdd-l10-l23-l25-supply = <&src_vreg_bob>;
vdd-l13-l19-l21-supply = <&src_vreg_bob>;
vdd-l16-l28-supply = <&src_vreg_bob>;
vdd-l18-l22-supply = <&src_vreg_bob>;
vdd-l20-l24-supply = <&src_vreg_bob>;
vdd-l26-supply = <&vreg_s3a_1p3>;
vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
vreg_s2a_1p1: smps2 {
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
};
vreg_s3a_1p3: smps3 {
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
};
vreg_s5a_1p9: smps5 {
regulator-min-microvolt = <1904000>;
regulator-max-microvolt = <2040000>;
};
vreg_s7a_0p9: smps7 {
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1028000>;
};
vreg_l1a_0p9: ldo1 {
regulator-min-microvolt = <880000>;
regulator-max-microvolt = <880000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l2a_1p2: ldo2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-always-on;
};
vreg_l3a_1p0: ldo3 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l5a_0p8: ldo5 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l6a_1p8: ldo6 {
regulator-min-microvolt = <1856000>;
regulator-max-microvolt = <1856000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l7a_1p8: ldo7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l8a_1p2: ldo8 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1248000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l9a_1p7: ldo9 {
regulator-min-microvolt = <1704000>;
regulator-max-microvolt = <2928000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l10a_1p7: ldo10 {
regulator-min-microvolt = <1704000>;
regulator-max-microvolt = <2928000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l11a_1p0: ldo11 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1048000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l12a_1p8: ldo12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l13a_1p8: ldo13 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l14a_1p8: ldo14 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-system-load = <62000>;
};
vreg_l15a_1p8: ldo15 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l16a_2p7: ldo16 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2704000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l17a_1p3: ldo17 {
regulator-min-microvolt = <1304000>;
regulator-max-microvolt = <1304000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l18a_2p7: ldo18 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l19a_2p7: ldo19 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
/*
* The driver *really* doesn't want this regualtor to exist,
* saying that it could not get the current voltage (-ENOTRECOVERABLE)
* even though it surely is used on these devices (as a voltage
* source for camera autofocus)
*/
status = "disabled";
};
vreg_l20a_2p7: ldo20 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l21a_2p7: ldo21 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l22a_2p8: ldo22 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l23a_3p0: ldo23 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3312000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l24a_3p1: ldo24 {
regulator-min-microvolt = <3088000>;
regulator-max-microvolt = <3088000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l25a_3p0: ldo25 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3312000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l26a_1p2: ldo26 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l28a_2p8: ldo28 {
regulator-min-microvolt = <2856000>;
regulator-max-microvolt = <3008000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-system-load = <100000>;
};
vreg_lvs1a_1p8: lvs1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_lvs2a_1p8: lvs2 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
};
regulators-1 {
compatible = "qcom,pmi8998-rpmh-regulators";
qcom,pmic-id = "b";
src_vreg_bob: bob {
regulator-min-microvolt = <3312000>;
regulator-max-microvolt = <3600000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
};
regulators-2 {
compatible = "qcom,pm8005-rpmh-regulators";
qcom,pmic-id = "c";
vdd-s1-supply = <&vph_pwr>;
vdd-s2-supply = <&vph_pwr>;
vdd-s3-supply = <&vph_pwr>;
vdd-s4-supply = <&vph_pwr>;
vreg_s3c_0p6: smps3 {
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <600000>;
};
};
};
&cdsp_pas {
firmware-name = "qcom/sdm845/Sony/tama/cdsp.mbn";
status = "okay";
};
&gcc {
protected-clocks = <GCC_QSPI_CORE_CLK>,
<GCC_QSPI_CORE_CLK_SRC>,
<GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
<GCC_LPASS_Q6_AXI_CLK>,
<GCC_LPASS_SWAY_CLK>;
};
&gmu {
status = "okay";
};
&gpi_dma0 {
status = "okay";
};
&gpi_dma1 {
status = "okay";
};
&gpu {
status = "okay";
zap-shader {
memory-region = <&gpu_mem>;
firmware-name = "qcom/sdm845/Sony/tama/a630_zap.mbn";
};
};
&i2c5 {
clock-frequency = <400000>;
status = "okay";
touchscreen: touchscreen@2c {
compatible = "syna,rmi4-i2c";
reg = <0x2c>;
interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
vdd-supply = <&vreg_l14a_1p8>;
/*
* This is a blatant abuse of OF, but the panel driver *needs*
* to probe first, as the power/gpio switching needs to be precisely
* timed in order for both the display and touch panel to function properly.
*/
incell-supply = <&panel>;
syna,reset-delay-ms = <220>;
syna,startup-delay-ms = <1000>;
pinctrl-0 = <&ts_default>;
pinctrl-1 = <&ts_sleep>;
pinctrl-names = "default", "sleep";
#address-cells = <1>;
#size-cells = <0>;
rmi4-f01@1 {
reg = <0x01>;
syna,nosleep-mode = <1>;
};
rmi4-f12@12 {
reg = <0x12>;
syna,sensor-type = <1>;
};
};
};
&i2c10 {
status = "okay";
clock-frequency = <400000>;
/* Qcom SMB1355 @ 8, c */
/* NXP PN547 NFC @ 28 */
/* Renesas IDTP9221 Qi charger @ 61 */
};
&i2c14 {
status = "okay";
clock-frequency = <400000>;
/* SONY ToF sensor @ 52 */
/* AMS TCS3490 RGB+IR color sensor @ 72 */
};
&ibb {
qcom,discharge-resistor-kohms = <300>;
regulator-min-microvolt = <5500000>;
regulator-max-microvolt = <5700000>;
regulator-min-microamp = <0>;
regulator-max-microamp = <800000>;
regulator-over-current-protection;
regulator-soft-start;
regulator-pull-down;
};
&lab {
regulator-min-microvolt = <5500000>;
regulator-max-microvolt = <5700000>;
regulator-min-microamp = <200000>;
regulator-max-microamp = <200000>;
regulator-over-current-protection;
regulator-soft-start;
regulator-pull-down;
};
&mdss {
status = "okay";
};
&mdss_dsi0 {
vdda-supply = <&vreg_l26a_1p2>;
status = "okay";
panel: panel@0 {
/* The compatible is assigned in device DTs. */
reg = <0>;
backlight = <&pmi8998_wled>;
vddio-supply = <&vreg_l14a_1p8>;
vsp-supply = <&lab>;
vsn-supply = <&ibb>;
panel-reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>;
touch-reset-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&sde_dsi_active &sde_te_active_sleep>;
pinctrl-1 = <&sde_dsi_sleep &sde_te_active_sleep>;
pinctrl-names = "default", "sleep";
port {
panel_in: endpoint {
remote-endpoint = <&mdss_dsi0_out>;
};
};
};
};
&mdss_dsi0_out {
remote-endpoint = <&panel_in>;
data-lanes = <0 1 2 3>;
};
&mdss_dsi0_phy {
vdds-supply = <&vreg_l1a_0p9>;
status = "okay";
};
&pm8998_gpios {
focus_n: focus-n-state {
pins = "gpio2";
function = PMIC_GPIO_FUNC_NORMAL;
power-source = <0>;
bias-pull-up;
input-enable;
};
vol_down_n: vol-down-n-state {
pins = "gpio5";
function = PMIC_GPIO_FUNC_NORMAL;
power-source = <0>;
bias-pull-up;
input-enable;
};
vol_up_n: vol-up-n-state {
pins = "gpio6";
function = PMIC_GPIO_FUNC_NORMAL;
power-source = <0>;
bias-pull-up;
input-enable;
};
snapshot_n: snapshot-n-state {
pins = "gpio7";
function = PMIC_GPIO_FUNC_NORMAL;
power-source = <0>;
bias-pull-up;
input-enable;
};
};
&pmi8998_wled {
default-brightness = <800>;
qcom,switching-freq = <800>;
qcom,ovp-millivolt = <29600>;
qcom,current-boost-limit = <970>;
qcom,current-limit-microamp = <20000>;
qcom,enabled-strings = <0 1 2 3>;
status = "okay";
};
&qupv3_id_0 {
status = "okay";
};
&qupv3_id_1 {
status = "okay";
};
&sdhc_2 {
status = "okay";
vmmc-supply = <&vreg_l21a_2p7>;
vqmmc-supply = <&vreg_l13a_1p8>;
cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&sdc2_default_state>;
pinctrl-names = "default";
bus-width = <4>;
no-sdio;
no-mmc;
};
&tlmm {
gpio-reserved-ranges = <0 4>, <81 4>;
sdc2_default_state: sdc2-default-state {
clk-pins {
pins = "sdc2_clk";
drive-strength = <16>;
bias-disable;
};
cmd-pins {
pins = "sdc2_cmd";
drive-strength = <10>;
bias-pull-up;
};
data-pins {
pins = "sdc2_data";
drive-strength = <10>;
bias-pull-up;
};
};
sde_dsi_active: sde-dsi-active-state {
pins = "gpio6";
function = "gpio";
drive-strength = <8>;
bias-disable;
};
sde_dsi_sleep: sde-dsi-sleep-state {
pins = "gpio6";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
};
sde_te_active_sleep: sde-te-active-sleep-state {
pins = "gpio10";
function = "mdp_vsync";
drive-strength = <2>;
bias-pull-down;
};
ts_default: ts-default-state {
reset-pins {
pins = "gpio99";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
int-pins {
pins = "gpio125";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};
ts_sleep: ts-sleep-state {
reset-pins {
pins = "gpio99";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
};
int-pins {
pins = "gpio125";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
};
};
};
&uart6 {
status = "okay";
};
&uart9 {
status = "okay";
};
/* BIG WARNING! DO NOT TOUCH UFS, YOUR DEVICE WILL DIE! */
&ufs_mem_hc { status = "disabled"; };
&ufs_mem_phy { status = "disabled"; };
&usb_1 {
status = "okay";
qcom,select-utmi-as-pipe-clk;
};
&usb_1_dwc3 {
dr_mode = "peripheral";
maximum-speed = "high-speed";
phys = <&usb_1_hsphy>;
phy-names = "usb2-phy";
};
&usb_1_hsphy {
status = "okay";
vdd-supply = <&vreg_l1a_0p9>;
vdda-pll-supply = <&vreg_l12a_1p8>;
vdda-phy-dpdm-supply = <&vreg_l24a_3p1>;
};
&venus {
firmware-name = "qcom/sdm845/Sony/tama/venus.mbn";
status = "okay";
};