# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/leds/ti,lm3533.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: TI LM3533 Complete Lighting Power Solution
description: >
The LM3533 is a complete power source for backlight, keypad, and indicator LEDs
in smartphone handsets. The high-voltage inductive boost converter provides the
power for two high voltage series LED strings for display backlight and four low
voltage control banks for individual LEDs. Additionally, LM3533 features an
interface for an external light sensor.
https://www.ti.com/product/LM3533
maintainers:
- Svyatoslav Ryhel <clamor95@gmail.com>
properties:
compatible:
const: ti,lm3533
reg:
maxItems: 1
enable-gpios:
description: GPIO connected to the HWEN pin.
maxItems: 1
vin-supply:
description: Supply connected to the IN line (2.7 V to 5.5 V).
'#address-cells':
const: 1
'#size-cells':
const: 0
ti,boost-ovp-microvolt:
description: boost OVP select (16V, 24V, 32V, 40V)
enum: [ 16000000, 24000000, 32000000, 40000000 ]
default: 16000000
ti,boost-freq-hz:
description: boost frequency select (500KHz or 1MHz)
enum: [ 500000, 1000000 ]
default: 500000
light-sensor:
type: object
additionalProperties: false
properties:
compatible:
const: ti,lm3533-als
interrupts:
maxItems: 1
ti,resistor-ohms:
description:
Internal configuration resistor value when light sensor is in
Analog Sensor mode and PWM mode is disabled. The expectation is
the input is a current from the external analog light sensor and
this is used to convert it to a voltage within the target range.
minimum: 1575
maximum: 200000
ti,pwm-mode:
type: boolean
description:
Switch for mode in which light sensor interface is running. If
this property is set then the light sensor interface is running
in PWM mode, internal resistor value is set to high-impedance (0)
and ti,resistor-ohms property is ignored.
required:
- compatible
oneOf:
- required:
- ti,resistor-ohms
- required:
- ti,pwm-mode
patternProperties:
"^backlight@[01]$":
$ref: /schemas/leds/backlight/ti,lm3533-backlight.yaml#
"^led@[2-5]$":
$ref: /schemas/leds/ti,lm3533-leds.yaml#
required:
- compatible
- reg
- '#address-cells'
- '#size-cells'
additionalProperties: false
examples:
- |
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
i2c {
#address-cells = <1>;
#size-cells = <0>;
led-controller@36 {
compatible = "ti,lm3533";
reg = <0x36>;
enable-gpios = <&gpio 110 GPIO_ACTIVE_HIGH>;
vin-supply = <&vdd_3v3_bat>;
ti,boost-ovp-microvolt = <24000000>;
ti,boost-freq-hz = <500000>;
#address-cells = <1>;
#size-cells = <0>;
backlight@0 {
compatible = "ti,lm3533-backlight";
reg = <0>;
default-brightness = <113>;
led-max-microamp = <23400>;
led-sources = <0 1>;
};
led@2 {
compatible = "ti,lm3533-leds";
reg = <2>;
led-max-microamp = <23400>;
led-sources = <0 1>;
};
led@4 {
compatible = "ti,lm3533-leds";
reg = <4>;
led-max-microamp = <23400>;
led-sources = <2>;
};
led@5 {
compatible = "ti,lm3533-leds";
reg = <5>;
led-max-microamp = <23400>;
led-sources = <3 4>;
};
light-sensor {
compatible = "ti,lm3533-als";
interrupt-parent = <&gpio>;
interrupts = <80 IRQ_TYPE_LEVEL_LOW>;
ti,pwm-mode;
};
};
};
...