# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/microchip,sparx5-switch.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Microchip Sparx5 Ethernet switch controller

maintainers:
  - Steen Hegelund <steen.hegelund@microchip.com>
  - Lars Povlsen <lars.povlsen@microchip.com>
  - Daniel Machon <daniel.machon@microchip.com>

description: |
  The SparX-5 Enterprise Ethernet switch family provides a rich set of
  Enterprise switching features such as advanced TCAM-based VLAN and
  QoS processing enabling delivery of differentiated services, and
  security through TCAM-based frame processing using versatile content
  aware processor (VCAP).

  IPv4/IPv6 Layer 3 (L3) unicast and multicast routing is supported
  with up to 18K IPv4/9K IPv6 unicast LPM entries and up to 9K IPv4/3K
  IPv6 (S,G) multicast groups.

  L3 security features include source guard and reverse path
  forwarding (uRPF) tasks. Additional L3 features include VRF-Lite and
  IP tunnels (IP over GRE/IP).

  The SparX-5 switch family targets managed Layer 2 and Layer 3
  equipment in SMB, SME, and Enterprise where high port count
  1G/2.5G/5G/10G switching with 10G/25G aggregation links is required.

properties:
  $nodename:
    pattern: "^switch@[0-9a-f]+$"

  compatible:
    oneOf:
      - enum:
          - microchip,lan9691-switch
          - microchip,sparx5-switch
      - items:
          - enum:
              - microchip,lan969c-switch
              - microchip,lan969b-switch
              - microchip,lan969a-switch
              - microchip,lan9699-switch
              - microchip,lan9698-switch
              - microchip,lan9697-switch
              - microchip,lan9696-switch
              - microchip,lan9695-switch
              - microchip,lan9694-switch
              - microchip,lan9693-switch
              - microchip,lan9692-switch
          - const: microchip,lan9691-switch

  reg:
    minItems: 2
    items:
      - description: cpu target
      - description: devices target
      - description: general control block target

  reg-names:
    minItems: 2
    items:
      - const: cpu
      - const: devices
      - const: gcb

  interrupts:
    minItems: 1
    items:
      - description: register based extraction
      - description: frame dma based extraction
      - description: ptp interrupt

  interrupt-names:
    minItems: 1
    items:
      - const: xtr
      - const: fdma
      - const: ptp

  resets:
    items:
      - description: Reset controller used for switch core reset (soft reset)

  reset-names:
    items:
      - const: switch

  mac-address: true

  ethernet-ports:
    type: object
    additionalProperties: false

    properties:
      '#address-cells':
        const: 1
      '#size-cells':
        const: 0

    patternProperties:
      "^port@[0-9a-f]+$":
        $ref: /schemas/net/ethernet-controller.yaml#
        unevaluatedProperties: false

        properties:
          reg:
            description: Switch port number

          phys:
            maxItems: 1
            description:
              phandle of a Ethernet SerDes PHY.  This defines which SerDes
              instance will handle the Ethernet traffic.

          microchip,bandwidth:
            description: Specifies bandwidth in Mbit/s allocated to the port.
            $ref: /schemas/types.yaml#/definitions/uint32
            maximum: 25000

          microchip,sd-sgpio:
            description:
              Index of the ports Signal Detect SGPIO in the set of 384 SGPIOs
              This is optional, and only needed if the default used index is
              is not correct.
            $ref: /schemas/types.yaml#/definitions/uint32
            minimum: 0
            maximum: 383

          rx-internal-delay-ps:
            description:
              RGMII Receive Clock Delay defined in pico seconds, used to select
              the DLL phase shift between 1000 ps (45 degree shift at 1Gbps) and
              3300 ps (147 degree shift at 1Gbps). A value of 0 ps will disable
              any delay. The Default is no delay.
            enum: [0, 1000, 1700, 2000, 2500, 3000, 3300]
            default: 0

          tx-internal-delay-ps:
            description:
              RGMII Transmit Clock Delay defined in pico seconds, used to select
              the DLL phase shift between 1000 ps (45 degree shift at 1Gbps) and
              3300 ps (147 degree shift at 1Gbps). A value of 0 ps will disable
              any delay. The Default is no delay.
            enum: [0, 1000, 1700, 2000, 2500, 3000, 3300]
            default: 0

        required:
          - reg
          - phy-mode
          - microchip,bandwidth

        if:
          not:
            properties:
              phy-mode:
                contains:
                  enum:
                    - rgmii
                    - rgmii-id
                    - rgmii-rxid
                    - rgmii-txid
        then:
          required:
            - phys

        oneOf:
          - required:
              - phy-handle
          - required:
              - sfp
              - managed

required:
  - compatible
  - reg
  - reg-names
  - interrupts
  - interrupt-names
  - ethernet-ports

allOf:
  - if:
      properties:
        compatible:
          contains:
            enum:
              - microchip,lan9691-switch
    then:
      properties:
        reg:
          maxItems: 2
        reg-names:
          maxItems: 2
    else:
      properties:
        reg:
          minItems: 3
        reg-names:
          minItems: 3

additionalProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/arm-gic.h>
    switch: switch@600000000 {
      compatible = "microchip,sparx5-switch";
      reg = <0 0x401000>,
            <0x10004000 0x7fc000>,
            <0x11010000 0xaf0000>;
      reg-names = "cpu", "devices", "gcb";
      interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
      interrupt-names = "xtr";
      resets = <&reset 0>;
      reset-names = "switch";
      ethernet-ports {
        #address-cells = <1>;
        #size-cells = <0>;

        port0: port@0 {
          reg = <0>;
          microchip,bandwidth = <1000>;
          phys = <&serdes 13>;
          phy-handle = <&phy0>;
          phy-mode = "qsgmii";
        };
        /* ... */
        /* Then the 25G interfaces */
        port60: port@60 {
          reg = <60>;
          microchip,bandwidth = <25000>;
          phys = <&serdes 29>;
          phy-mode = "10gbase-r";
          sfp = <&sfp_eth60>;
          managed = "in-band-status";
          microchip,sd-sgpio = <365>;
        };
        port61: port@61 {
          reg = <61>;
          microchip,bandwidth = <25000>;
          phys = <&serdes 30>;
          phy-mode = "10gbase-r";
          sfp = <&sfp_eth61>;
          managed = "in-band-status";
          microchip,sd-sgpio = <369>;
        };
        port62: port@62 {
          reg = <62>;
          microchip,bandwidth = <25000>;
          phys = <&serdes 31>;
          phy-mode = "10gbase-r";
          sfp = <&sfp_eth62>;
          managed = "in-band-status";
          microchip,sd-sgpio = <373>;
        };
        port63: port@63 {
          reg = <63>;
          microchip,bandwidth = <25000>;
          phys = <&serdes 32>;
          phy-mode = "10gbase-r";
          sfp = <&sfp_eth63>;
          managed = "in-band-status";
          microchip,sd-sgpio = <377>;
        };
        /* Finally the Management interface */
        port64: port@64 {
          reg = <64>;
          microchip,bandwidth = <1000>;
          phys = <&serdes 0>;
          phy-handle = <&phy64>;
          phy-mode = "sgmii";
          mac-address = [ 00 00 00 01 02 03 ];
        };
      };
    };

...