#!/bin/bash
# SPDX-License-Identifier: GPL-2.0
# Copyright(c) 2020 Intel Corporation, Weqaar Janjua <weqaar.a.janjua@intel.com>

# AF_XDP selftests based on veth
#
# End-to-end AF_XDP over Veth test
#
# Topology:
# ---------
#                 -----------
#               _ | Process | _
#              /  -----------  \
#             /        |        \
#            /         |         \
#      -----------     |     -----------
#      | Thread1 |     |     | Thread2 |
#      -----------     |     -----------
#           |          |          |
#      -----------     |     -----------
#      |  xskX   |     |     |  xskY   |
#      -----------     |     -----------
#           |          |          |
#      -----------     |     ----------
#      |  vethX  | --------- |  vethY |
#      -----------   peer    ----------
#
# AF_XDP is an address family optimized for high performance packet processing,
# it is XDP’s user-space interface.
#
# An AF_XDP socket is linked to a single UMEM which is a region of virtual
# contiguous memory, divided into equal-sized frames.
#
# Refer to AF_XDP Kernel Documentation for detailed information:
# https://www.kernel.org/doc/html/latest/networking/af_xdp.html
#
# Prerequisites setup by script:
#
#   Set up veth interfaces as per the topology shown ^^:
#   * setup two veth interfaces
#   ** veth<xxxx>
#   ** veth<yyyy>
#   *** xxxx and yyyy are randomly generated 4 digit numbers used to avoid
#       conflict with any existing interface
#   * tests the veth and xsk layers of the topology
#
# See the source xskxceiver.c for information on each test
#
# Kernel configuration:
# ---------------------
# See "config" file for recommended kernel config options.
#
# Turn on XDP sockets and veth support when compiling i.e.
# 	Networking support -->
# 		Networking options -->
# 			[ * ] XDP sockets
#
# Executing Tests:
# ----------------
# Must run with CAP_NET_ADMIN capability.
#
# Run:
#   sudo ./test_xsk.sh
#
# If running from kselftests:
#   sudo make run_tests
#
# Run with verbose output:
#   sudo ./test_xsk.sh -v
#
# Set up veth interfaces and leave them up so xskxceiver can be launched in a debugger:
#   sudo ./test_xsk.sh -d
#
# Run test suite for physical device in loopback mode
#   sudo ./test_xsk.sh -i IFACE

. xsk_prereqs.sh

ETH=""

while getopts "vi:d" flag
do
	case "${flag}" in
		v) verbose=1;;
		d) debug=1;;
		i) ETH=${OPTARG};;
	esac
done

TEST_NAME="PREREQUISITES"

URANDOM=/dev/urandom
[ ! -e "${URANDOM}" ] && { echo "${URANDOM} not found. Skipping tests."; test_exit $ksft_fail; }

VETH0_POSTFIX=$(cat ${URANDOM} | tr -dc '0-9' | fold -w 256 | head -n 1 | head --bytes 4)
VETH0=ve${VETH0_POSTFIX}
VETH1_POSTFIX=$(cat ${URANDOM} | tr -dc '0-9' | fold -w 256 | head -n 1 | head --bytes 4)
VETH1=ve${VETH1_POSTFIX}
MTU=1500

trap ctrl_c INT

function ctrl_c() {
        cleanup_exit ${VETH0} ${VETH1}
	exit 1
}

setup_vethPairs() {
	if [[ $verbose -eq 1 ]]; then
	        echo "setting up ${VETH0}"
	fi
	ip link add ${VETH0} numtxqueues 4 numrxqueues 4 type veth peer name ${VETH1} numtxqueues 4 numrxqueues 4
	if [ -f /proc/net/if_inet6 ]; then
		echo 1 > /proc/sys/net/ipv6/conf/${VETH0}/disable_ipv6
		echo 1 > /proc/sys/net/ipv6/conf/${VETH1}/disable_ipv6
	fi
	if [[ $verbose -eq 1 ]]; then
	        echo "setting up ${VETH1}"
	fi

	if [[ $busy_poll -eq 1 ]]; then
	        echo 2 > /sys/class/net/${VETH0}/napi_defer_hard_irqs
		echo 200000 > /sys/class/net/${VETH0}/gro_flush_timeout
		echo 2 > /sys/class/net/${VETH1}/napi_defer_hard_irqs
		echo 200000 > /sys/class/net/${VETH1}/gro_flush_timeout
	fi

	ip link set ${VETH1} mtu ${MTU}
	ip link set ${VETH0} mtu ${MTU}
	ip link set ${VETH1} up
	ip link set ${VETH0} up
}

if [ ! -z $ETH ]; then
	VETH0=${ETH}
	VETH1=${ETH}
else
	validate_root_exec
	validate_veth_support ${VETH0}
	validate_ip_utility
	setup_vethPairs

	retval=$?
	if [ $retval -ne 0 ]; then
		test_status $retval "${TEST_NAME}"
		cleanup_exit ${VETH0} ${VETH1}
		exit $retval
	fi
fi


if [[ $verbose -eq 1 ]]; then
	ARGS+="-v "
fi

retval=$?
test_status $retval "${TEST_NAME}"

## START TESTS

statusList=()

TEST_NAME="XSK_SELFTESTS_${VETH0}_SOFTIRQ"

if [[ $debug -eq 1 ]]; then
    echo "-i" ${VETH0} "-i" ${VETH1}
    exit
fi

exec_xskxceiver

if [ -z $ETH ]; then
	cleanup_exit ${VETH0} ${VETH1}
else
	cleanup_iface ${ETH} ${MTU}
fi

TEST_NAME="XSK_SELFTESTS_${VETH0}_BUSY_POLL"
busy_poll=1

if [ -z $ETH ]; then
	setup_vethPairs
fi
exec_xskxceiver

## END TESTS

if [ -z $ETH ]; then
	cleanup_exit ${VETH0} ${VETH1}
else
	cleanup_iface ${ETH} ${MTU}
fi

failures=0
echo -e "\nSummary:"
for i in "${!statusList[@]}"
do
	if [ ${statusList[$i]} -ne 0 ]; then
	        test_status ${statusList[$i]} ${nameList[$i]}
		failures=1
	fi
done

if [ $failures -eq 0 ]; then
        echo "All tests successful!"
fi