// SPDX-License-Identifier: (GPL-2.0 OR MIT)
//
// Device Tree file for LX2160A-CEx7
//
// Copyright 2019 SolidRun Ltd.

/ {
	model = "SolidRun LX2160A COM Express Type 7 module";
	compatible = "solidrun,lx2160a-cex7", "fsl,lx2160a";

	aliases {
		crypto = &crypto;
		rtc0 = &com_rtc;
	};

	v_1_2: regulator-1-2 {
		compatible = "regulator-fixed";
		regulator-name = "1v2";
		regulator-max-microvolt = <1200000>;
		regulator-min-microvolt = <1200000>;
	};

	sb_3v3: regulator-sb3v3 {
		compatible = "regulator-fixed";
		regulator-name = "RT7290";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		regulator-boot-on;
		regulator-always-on;
	};
};

&crypto {
	status = "okay";
};

&dpmac17 {
	phy-handle = <&rgmii_phy1>;
	phy-connection-type = "rgmii-id";
};

&emdio1 {
	status = "okay";

	rgmii_phy1: ethernet-phy@1 {
		reg = <1>;
		qca,smarteee-tw-us-1g = <24>;
		interrupts-extended = <&gpio2 4 IRQ_TYPE_EDGE_FALLING>;
	};
};

&esdhc1 {
	mmc-hs200-1_8v;
	mmc-hs400-1_8v;
	bus-width = <8>;
	status = "okay";
};

&i2c0 {
	status = "okay";

	i2c-mux@77 {
		compatible = "nxp,pca9547";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0x77>;

		ddr_i2c: i2c@0 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0>;

			eeprom@50 {
				compatible = "atmel,24c512";
				reg = <0x50>;
			};

			eeprom@51 {
				compatible = "atmel,spd";
				reg = <0x51>;
			};

			eeprom@53 {
				compatible = "atmel,spd";
				reg = <0x53>;
			};

			eeprom@57 {
				compatible = "atmel,24c02";
				reg = <0x57>;
			};
		};

		fan_i2c: i2c@1 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <1>;

			fan-temperature-ctrlr@18 {
				compatible = "ti,amc6821";
				reg = <0x18>;
			};
		};

		power_i2c: i2c@2 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <2>;

			regulator@5c {
				compatible = "lltc,ltc3882";
				reg = <0x5c>;
			};
		};

		i2c_smb: i2c@3 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <3>;

			temperature-sensor@48 {
				compatible = "nxp,sa56004";
				reg = <0x48>;
				vcc-supply = <&sb_3v3>;
			};
		};

		sfp0_i2c: i2c@4 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <4>;
		};

		sfp1_i2c: i2c@5 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <5>;
		};

		sfp2_i2c: i2c@6 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <6>;
		};

		sfp3_i2c: i2c@7 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <7>;
		};
	};
};

&i2c2 {
	status = "okay";
};

&i2c4 {
	status = "okay";

	com_rtc: rtc@51 {
		compatible = "nxp,pcf2129";
		reg = <0x51>;
		interrupts-extended = <&gpio2 8 IRQ_TYPE_LEVEL_LOW>;
	};
};

&fspi {
	pinctrl-names = "default";
	pinctrl-0 = <&fspi_data74_pins>, <&fspi_data30_pins>, <&fspi_dqs_sck_cs10_pins>;
	status = "okay";

	flash@0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "micron,m25p80";
		m25p,fast-read;
		spi-max-frequency = <50000000>;
		reg = <0>;
		/* The following setting enables 1-1-8 (CMD-ADDR-DATA) mode */
		spi-rx-bus-width = <8>;
		spi-tx-bus-width = <1>;
	};
};

&pinmux_i2crv {
	pinctrl-names = "default";
	pinctrl-0 = <&gpio0_14_12_pins>;
};

&usb1 {
	#address-cells = <1>;
	#size-cells = <0>;
	status = "okay";

	usb_hub_2_0: hub@1 {
		compatible = "usb4b4,6502", "usb4b4,6506";
		reg = <1>;
		peer-hub = <&usb_hub_3_0>;
		vdd2-supply = <&sb_3v3>;
		vdd-supply = <&v_1_2>;
	};

	usb_hub_3_0: hub@2 {
		compatible = "usb4b4,6500", "usb4b4,6504";
		reg = <2>;
		peer-hub = <&usb_hub_2_0>;
		vdd2-supply = <&sb_3v3>;
		vdd-supply = <&v_1_2>;
	};
};