# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/phy/qcom,x1e80100-csi2-phy.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Qualcomm X1E80100 SoC CSI2 PHY
maintainers:
- Bryan O'Donoghue <bod@kernel.org>
description:
Qualcomm MIPI CSI2 C-PHY/D-PHY combination PHY. Connects MIPI CSI2 sensors
to Qualcomm's Camera CSI Decoder. The PHY supports both C-PHY and D-PHY
modes.
properties:
compatible:
oneOf:
- const: qcom,x1e80100-csi2-phy
- items:
- const: qcom,glymur-csi2-phy
- const: qcom,x1e80100-csi2-phy
reg:
maxItems: 1
clocks:
maxItems: 3
clock-names:
items:
- const: core
- const: timer
- const: ahb
interrupts:
maxItems: 1
operating-points-v2: true
opp-table:
type: object
power-domains:
items:
- description: Titan Top GDSC - Titan ISP Block, Global Distributed Switch Controller.
- description: MMCX voltage rail
- description: MXC or MXA voltage rail
power-domain-names:
items:
- const: top
- const: mmcx
- const: mx
vdda-0p9-supply:
description: Phandle to a 0.9V regulator supply to a PHY.
vdda-1p2-supply:
description: Phandle to 1.2V regulator supply to a PHY.
ports:
$ref: /schemas/graph.yaml#/properties/ports
properties:
port@0:
$ref: /schemas/graph.yaml#/$defs/port-base
description:
Sensor input. Always present. A single sensor is described by a
single endpoint with one to four data lanes, numbered 1-4. The
clock lane is position 0.
DPHY split mode, where two independent sensors share the PHY, is
described by two endpoints. endpoint@0 uses data lanes 1 or 1-2,
clock lane position 0; endpoint@1 uses data lane 3, clock lane
position 4.
unevaluatedProperties: false
patternProperties:
"^endpoint(@[01])?$":
$ref: /schemas/media/video-interfaces.yaml#
unevaluatedProperties: false
properties:
bus-type:
enum:
- 1 # MEDIA_BUS_TYPE_CSI2_CPHY
- 4 # MEDIA_BUS_TYPE_CSI2_DPHY
default: 4
data-lanes:
minItems: 1
maxItems: 4
items:
minimum: 1
maximum: 4
description:
Data lane positions following this endpoint's clock
lane. Positions are a per-port logical numbering, not
package pad or ball positions.
required:
- data-lanes
- remote-endpoint
allOf:
- if:
required:
- endpoint@1
then:
properties:
endpoint@0:
properties:
data-lanes:
maxItems: 2
items:
maximum: 2
endpoint@1:
properties:
data-lanes:
items:
- const: 3
required:
- endpoint@0
port@1:
$ref: /schemas/graph.yaml#/properties/port
description: Output to the CAMSS CSID controller.
required:
- port@0
- port@1
required:
- compatible
- reg
- clocks
- clock-names
- interrupts
- operating-points-v2
- power-domains
- power-domain-names
- vdda-0p9-supply
- vdda-1p2-supply
- ports
additionalProperties: false
examples:
- |
#include <dt-bindings/clock/qcom,x1e80100-camcc.h>
#include <dt-bindings/clock/qcom,x1e80100-gcc.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/media/video-interfaces.h>
#include <dt-bindings/power/qcom,rpmhpd.h>
phy@ace4000 {
compatible = "qcom,x1e80100-csi2-phy";
reg = <0x0ace4000 0x2000>;
clocks = <&camcc CAM_CC_CSIPHY0_CLK>,
<&camcc CAM_CC_CSI0PHYTIMER_CLK>,
<&camcc CAM_CC_CORE_AHB_CLK>;
clock-names = "core",
"timer",
"ahb";
interrupts = <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>;
operating-points-v2 = <&csiphy_opp_table>;
power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>,
<&rpmhpd RPMHPD_MMCX>,
<&rpmhpd RPMHPD_MX>;
power-domain-names = "top",
"mmcx",
"mx";
vdda-0p9-supply = <&vreg_l2c_0p9>;
vdda-1p2-supply = <&vreg_l1c_1p2>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
csiphy0_in: endpoint {
bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
data-lanes = <1 2 3 4>;
remote-endpoint = <&sensor_out>;
};
};
port@1 {
reg = <1>;
csiphy0_out: endpoint {
remote-endpoint = <&csid_in>;
};
};
};
csiphy_opp_table: opp-table {
compatible = "operating-points-v2";
opp-300000000 {
opp-hz = /bits/ 64 <300000000>;
required-opps = <&rpmhpd_opp_low_svs_d1>,
<&rpmhpd_opp_low_svs_d1>;
};
};
};