# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
%YAML 1.2
---
$id: http://devicetree.org/schemas/remoteproc/qcom,kaanapali-soccp-pas.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Qualcomm Kaanapali SoCCP Peripheral Authentication Service
maintainers:
- Jingyi Wang <jingyi.wang@oss.qualcomm.com>
description:
The SoC Control Processor (SoCCP) is a small RISC-V MCU that controls USB
Type-C, battery charging and various other functions on Qualcomm SoCs, somewhat
analogous to traditional PC Embedded Controllers. This document describes
the Peripheral Authentication Service that loads and boots firmware for SoCCP.
properties:
compatible:
oneOf:
- items:
- enum:
- qcom,hawi-soccp-pas
- qcom,maili-soccp-pas
- const: qcom,kaanapali-soccp-pas
- enum:
- qcom,glymur-soccp-pas
- qcom,kaanapali-soccp-pas
reg:
maxItems: 1
clocks:
items:
- description: XO clock
clock-names:
items:
- const: xo
power-domains:
items:
- description: CX power domain
- description: MX power domain
power-domain-names:
items:
- const: cx
- const: mx
firmware-name:
items:
- description: Firmware name of the SoC Control Processor
- description: Firmware name of the SoCCP Devicetree
memory-region:
items:
- description: Memory region for main Firmware authentication
- description: Memory region for Devicetree Firmware authentication
interrupts:
items:
- description: Watchdog interrupt
- description: Fatal interrupt
- description: Ready interrupt
- description: Handover interrupt
- description: Stop acknowledge interrupt
- description: Pong interrupt
interrupt-names:
items:
- const: wdog
- const: fatal
- const: ready
- const: handover
- const: stop-ack
- const: pong
qcom,smem-states:
minItems: 2
description: States used by the AP to signal the SoC Control Processor
qcom,smem-state-names:
minItems: 2
description: The names of the state bits used for SMP2P output
required:
- compatible
- reg
- memory-region
- power-domains
- power-domain-names
allOf:
- $ref: /schemas/remoteproc/qcom,pas-common.yaml#
unevaluatedProperties: false
examples:
- |
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#define IPCC_MPROC_SOCCP
remoteproc@d00000 {
compatible = "qcom,kaanapali-soccp-pas";
reg = <0x00d00000 0x200000>;
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "xo";
interrupts-extended = <&intc GIC_SPI 167 IRQ_TYPE_EDGE_RISING>,
<&soccp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
<&soccp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
<&soccp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
<&soccp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
<&soccp_smp2p_in 9 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "wdog",
"fatal",
"ready",
"handover",
"stop-ack",
"pong";
memory-region = <&soccp_mem>,
<&soccp_dtb_mem_mem>;
firmware-name = "qcom/kaanapali/soccp.mbn",
"qcom/kaanapali/soccp_dtb.mbn";
power-domains = <&rpmhpd RPMHPD_CX>,
<&rpmhpd RPMHPD_MX>;
power-domain-names = "cx",
"mx";
qcom,smem-states = <&soccp_smp2p_out 0>,
<&soccp_smp2p_out 8>;
qcom,smem-state-names = "stop",
"ping";
glink-edge {
interrupts-extended = <&ipcc IPCC_MPROC_SOCCP
IPCC_MPROC_SIGNAL_GLINK_QMP
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_MPROC_SOCCP
IPCC_MPROC_SIGNAL_GLINK_QMP>;
label = "soccp";
qcom,remote-pid = <19>;
/* ... */
};
};