// SPDX-License-Identifier: GPL-2.0-only
/*
* Device Tree Source for OMAP3 SoC
*
* Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
*/
#include <dt-bindings/bus/ti-sysc.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/omap.h>
/ {
compatible = "ti,omap3430", "ti,omap3";
interrupt-parent = <&intc>;
#address-cells = <1>;
#size-cells = <1>;
chosen { };
aliases {
i2c0 = &i2c1;
i2c1 = &i2c2;
i2c2 = &i2c3;
mmc0 = &mmc1;
mmc1 = &mmc2;
mmc2 = &mmc3;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu@0 {
compatible = "arm,cortex-a8";
device_type = "cpu";
reg = <0x0>;
clocks = <&dpll1_ck>;
clock-names = "cpu";
clock-latency = <300000>; /* From omap-cpufreq driver */
};
};
pmu@54000000 {
compatible = "arm,cortex-a8-pmu";
reg = <0x54000000 0x800000>;
interrupts = <3>;
ti,hwmods = "debugss";
};
/*
* The soc node represents the soc top level view. It is used for IPs
* that are not memory mapped in the MPU view or for the MPU itself.
*/
soc {
compatible = "ti,omap-infra";
mpu {
compatible = "ti,omap3-mpu";
ti,hwmods = "mpu";
};
iva: iva {
compatible = "ti,iva2.2";
ti,hwmods = "iva";
dsp {
compatible = "ti,omap3-c64";
};
};
};
/*
* XXX: Use a flat representation of the OMAP3 interconnect.
* The real OMAP interconnect network is quite complex.
* Since it will not bring real advantage to represent that in DT for
* the moment, just use a fake OCP bus entry to represent the whole bus
* hierarchy.
*/
ocp@68000000 {
compatible = "ti,omap3-l3-smx", "simple-bus";
reg = <0x68000000 0x10000>;
interrupts = <9 10>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
ti,hwmods = "l3_main";
l4_core: l4@48000000 {
compatible = "ti,omap3-l4-core", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x48000000 0x1000000>;
scm: scm@2000 {
compatible = "ti,omap3-scm", "simple-bus";
reg = <0x2000 0x2000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x2000 0x2000>;
omap3_pmx_core: pinmux@30 {
compatible = "ti,omap3-padconf",
"pinctrl-single";
reg = <0x30 0x238>;
#address-cells = <1>;
#size-cells = <0>;
#pinctrl-cells = <1>;
#interrupt-cells = <1>;
interrupt-controller;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0xff1f>;
};
scm_conf: scm_conf@270 {
compatible = "syscon", "simple-bus";
reg = <0x270 0x330>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x270 0x330>;
pbias_regulator: pbias_regulator@2b0 {
compatible = "ti,pbias-omap3", "ti,pbias-omap";
reg = <0x2b0 0x4>;
syscon = <&scm_conf>;
pbias_mmc_reg: pbias_mmc_omap2430 {
regulator-name = "pbias_mmc_omap2430";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3000000>;
};
};
scm_clocks: clocks {
#address-cells = <1>;
#size-cells = <0>;
};
};
scm_clockdomains: clockdomains {
};
omap3_pmx_wkup: pinmux@a00 {
compatible = "ti,omap3-padconf",
"pinctrl-single";
reg = <0xa00 0x5c>;
#address-cells = <1>;
#size-cells = <0>;
#pinctrl-cells = <1>;
#interrupt-cells = <1>;
interrupt-controller;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0xff1f>;
};
};
};
aes1_target: target-module@480a6000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x480a6044 0x4>,
<0x480a6048 0x4>,
<0x480a604c 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-mask = <(SYSC_OMAP2_AUTOIDLE)>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,syss-mask = <1>;
clocks = <&aes1_ick>;
clock-names = "ick";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x480a6000 0x2000>;
aes1: aes1@0 {
compatible = "ti,omap3-aes";
reg = <0 0x50>;
interrupts = <0>;
dmas = <&sdma 9 &sdma 10>;
dma-names = "tx", "rx";
};
};
aes2_target: target-module@480c5000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x480c5044 0x4>,
<0x480c5048 0x4>,
<0x480c504c 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-mask = <(SYSC_OMAP2_AUTOIDLE)>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,syss-mask = <1>;
clocks = <&aes2_ick>;
clock-names = "ick";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x480c5000 0x2000>;
aes2: aes2@0 {
compatible = "ti,omap3-aes";
reg = <0 0x50>;
interrupts = <0>;
dmas = <&sdma 65 &sdma 66>;
dma-names = "tx", "rx";
};
};
prm: prm@48306000 {
compatible = "ti,omap3-prm";
reg = <0x48306000 0x4000>;
interrupts = <11>;
prm_clocks: clocks {
#address-cells = <1>;
#size-cells = <0>;
};
prm_clockdomains: clockdomains {
};
};
cm: cm@48004000 {
compatible = "ti,omap3-cm";
reg = <0x48004000 0x4000>;
cm_clocks: clocks {
#address-cells = <1>;
#size-cells = <0>;
};
cm_clockdomains: clockdomains {
};
};
target-module@48320000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x48320000 0x4>,
<0x48320004 0x4>;
reg-names = "rev", "sysc";
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>;
clocks = <&wkup_32k_fck>, <&omap_32ksync_ick>;
clock-names = "fck", "ick";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x48320000 0x1000>;
counter32k: counter@0 {
compatible = "ti,omap-counter32k";
reg = <0x0 0x20>;
};
};
intc: interrupt-controller@48200000 {
compatible = "ti,omap3-intc";
interrupt-controller;
#interrupt-cells = <1>;
reg = <0x48200000 0x1000>;
};
target-module@48056000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x48056000 0x4>,
<0x4805602c 0x4>,
<0x48056028 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
SYSC_OMAP2_EMUFREE |
SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
ti,sysc-midle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,syss-mask = <1>;
/* Domains (V, P, C): core, core_pwrdm, core_l3_clkdm */
clocks = <&core_l3_ick>;
clock-names = "ick";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x48056000 0x1000>;
sdma: dma-controller@0 {
compatible = "ti,omap3430-sdma", "ti,omap-sdma";
reg = <0x0 0x1000>;
interrupts = <12>,
<13>,
<14>,
<15>;
#dma-cells = <1>;
dma-channels = <32>;
dma-requests = <96>;
};
};
gpio1: gpio@48310000 {
compatible = "ti,omap3-gpio";
reg = <0x48310000 0x200>;
interrupts = <29>;
ti,hwmods = "gpio1";
ti,gpio-always-on;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio2: gpio@49050000 {
compatible = "ti,omap3-gpio";
reg = <0x49050000 0x200>;
interrupts = <30>;
ti,hwmods = "gpio2";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio3: gpio@49052000 {
compatible = "ti,omap3-gpio";
reg = <0x49052000 0x200>;
interrupts = <31>;
ti,hwmods = "gpio3";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio4: gpio@49054000 {
compatible = "ti,omap3-gpio";
reg = <0x49054000 0x200>;
interrupts = <32>;
ti,hwmods = "gpio4";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio5: gpio@49056000 {
compatible = "ti,omap3-gpio";
reg = <0x49056000 0x200>;
interrupts = <33>;
ti,hwmods = "gpio5";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio6: gpio@49058000 {
compatible = "ti,omap3-gpio";
reg = <0x49058000 0x200>;
interrupts = <34>;
ti,hwmods = "gpio6";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
uart1: serial@4806a000 {
compatible = "ti,omap3-uart";
reg = <0x4806a000 0x2000>;
interrupts-extended = <&intc 72>;
dmas = <&sdma 49 &sdma 50>;
dma-names = "tx", "rx";
ti,hwmods = "uart1";
clock-frequency = <48000000>;
};
uart2: serial@4806c000 {
compatible = "ti,omap3-uart";
reg = <0x4806c000 0x400>;
interrupts-extended = <&intc 73>;
dmas = <&sdma 51 &sdma 52>;
dma-names = "tx", "rx";
ti,hwmods = "uart2";
clock-frequency = <48000000>;
};
uart3: serial@49020000 {
compatible = "ti,omap3-uart";
reg = <0x49020000 0x400>;
interrupts-extended = <&intc 74>;
dmas = <&sdma 53 &sdma 54>;
dma-names = "tx", "rx";
ti,hwmods = "uart3";
clock-frequency = <48000000>;
};
i2c1: i2c@48070000 {
compatible = "ti,omap3-i2c";
reg = <0x48070000 0x80>;
interrupts = <56>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c1";
};
i2c2: i2c@48072000 {
compatible = "ti,omap3-i2c";
reg = <0x48072000 0x80>;
interrupts = <57>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c2";
};
i2c3: i2c@48060000 {
compatible = "ti,omap3-i2c";
reg = <0x48060000 0x80>;
interrupts = <61>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c3";
};
mailbox: mailbox@48094000 {
compatible = "ti,omap3-mailbox";
ti,hwmods = "mailbox";
reg = <0x48094000 0x200>;
interrupts = <26>;
#mbox-cells = <1>;
ti,mbox-num-users = <2>;
ti,mbox-num-fifos = <2>;
mbox_dsp: mbox-dsp {
ti,mbox-tx = <0 0 0>;
ti,mbox-rx = <1 0 0>;
};
};
mcspi1: spi@48098000 {
compatible = "ti,omap2-mcspi";
reg = <0x48098000 0x100>;
interrupts = <65>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi1";
ti,spi-num-cs = <4>;
dmas = <&sdma 35>,
<&sdma 36>,
<&sdma 37>,
<&sdma 38>,
<&sdma 39>,
<&sdma 40>,
<&sdma 41>,
<&sdma 42>;
dma-names = "tx0", "rx0", "tx1", "rx1",
"tx2", "rx2", "tx3", "rx3";
};
mcspi2: spi@4809a000 {
compatible = "ti,omap2-mcspi";
reg = <0x4809a000 0x100>;
interrupts = <66>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi2";
ti,spi-num-cs = <2>;
dmas = <&sdma 43>,
<&sdma 44>,
<&sdma 45>,
<&sdma 46>;
dma-names = "tx0", "rx0", "tx1", "rx1";
};
mcspi3: spi@480b8000 {
compatible = "ti,omap2-mcspi";
reg = <0x480b8000 0x100>;
interrupts = <91>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi3";
ti,spi-num-cs = <2>;
dmas = <&sdma 15>,
<&sdma 16>,
<&sdma 23>,
<&sdma 24>;
dma-names = "tx0", "rx0", "tx1", "rx1";
};
mcspi4: spi@480ba000 {
compatible = "ti,omap2-mcspi";
reg = <0x480ba000 0x100>;
interrupts = <48>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi4";
ti,spi-num-cs = <1>;
dmas = <&sdma 70>, <&sdma 71>;
dma-names = "tx0", "rx0";
};
hdqw1w: 1w@480b2000 {
compatible = "ti,omap3-1w";
reg = <0x480b2000 0x1000>;
interrupts = <58>;
ti,hwmods = "hdq1w";
};
mmc1: mmc@4809c000 {
compatible = "ti,omap3-hsmmc";
reg = <0x4809c000 0x200>;
interrupts = <83>;
ti,hwmods = "mmc1";
ti,dual-volt;
dmas = <&sdma 61>, <&sdma 62>;
dma-names = "tx", "rx";
pbias-supply = <&pbias_mmc_reg>;
};
mmc2: mmc@480b4000 {
compatible = "ti,omap3-hsmmc";
reg = <0x480b4000 0x200>;
interrupts = <86>;
ti,hwmods = "mmc2";
dmas = <&sdma 47>, <&sdma 48>;
dma-names = "tx", "rx";
};
mmc3: mmc@480ad000 {
compatible = "ti,omap3-hsmmc";
reg = <0x480ad000 0x200>;
interrupts = <94>;
ti,hwmods = "mmc3";
dmas = <&sdma 77>, <&sdma 78>;
dma-names = "tx", "rx";
};
mmu_isp: mmu@480bd400 {
#iommu-cells = <0>;
compatible = "ti,omap2-iommu";
reg = <0x480bd400 0x80>;
interrupts = <24>;
ti,hwmods = "mmu_isp";
ti,#tlb-entries = <8>;
};
mmu_iva: mmu@5d000000 {
#iommu-cells = <0>;
compatible = "ti,omap2-iommu";
reg = <0x5d000000 0x80>;
interrupts = <28>;
ti,hwmods = "mmu_iva";
status = "disabled";
};
wdt2: wdt@48314000 {
compatible = "ti,omap3-wdt";
reg = <0x48314000 0x80>;
ti,hwmods = "wd_timer2";
};
mcbsp1: mcbsp@48074000 {
compatible = "ti,omap3-mcbsp";
reg = <0x48074000 0xff>;
reg-names = "mpu";
interrupts = <16>, /* OCP compliant interrupt */
<59>, /* TX interrupt */
<60>; /* RX interrupt */
interrupt-names = "common", "tx", "rx";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp1";
dmas = <&sdma 31>,
<&sdma 32>;
dma-names = "tx", "rx";
clocks = <&mcbsp1_fck>;
clock-names = "fck";
status = "disabled";
};
/* Likely needs to be tagged disabled on HS devices */
rng_target: target-module@480a0000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x480a003c 0x4>,
<0x480a0040 0x4>,
<0x480a0044 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-mask = <(SYSC_OMAP2_AUTOIDLE)>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>;
ti,syss-mask = <1>;
clocks = <&rng_ick>;
clock-names = "ick";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x480a0000 0x2000>;
rng: rng@0 {
compatible = "ti,omap2-rng";
reg = <0x0 0x2000>;
interrupts = <52>;
};
};
mcbsp2: mcbsp@49022000 {
compatible = "ti,omap3-mcbsp";
reg = <0x49022000 0xff>,
<0x49028000 0xff>;
reg-names = "mpu", "sidetone";
interrupts = <17>, /* OCP compliant interrupt */
<62>, /* TX interrupt */
<63>, /* RX interrupt */
<4>; /* Sidetone */
interrupt-names = "common", "tx", "rx", "sidetone";
ti,buffer-size = <1280>;
ti,hwmods = "mcbsp2", "mcbsp2_sidetone";
dmas = <&sdma 33>,
<&sdma 34>;
dma-names = "tx", "rx";
clocks = <&mcbsp2_fck>, <&mcbsp2_ick>;
clock-names = "fck", "ick";
status = "disabled";
};
mcbsp3: mcbsp@49024000 {
compatible = "ti,omap3-mcbsp";
reg = <0x49024000 0xff>,
<0x4902a000 0xff>;
reg-names = "mpu", "sidetone";
interrupts = <22>, /* OCP compliant interrupt */
<89>, /* TX interrupt */
<90>, /* RX interrupt */
<5>; /* Sidetone */
interrupt-names = "common", "tx", "rx", "sidetone";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp3", "mcbsp3_sidetone";
dmas = <&sdma 17>,
<&sdma 18>;
dma-names = "tx", "rx";
clocks = <&mcbsp3_fck>, <&mcbsp3_ick>;
clock-names = "fck", "ick";
status = "disabled";
};
mcbsp4: mcbsp@49026000 {
compatible = "ti,omap3-mcbsp";
reg = <0x49026000 0xff>;
reg-names = "mpu";
interrupts = <23>, /* OCP compliant interrupt */
<54>, /* TX interrupt */
<55>; /* RX interrupt */
interrupt-names = "common", "tx", "rx";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp4";
dmas = <&sdma 19>,
<&sdma 20>;
dma-names = "tx", "rx";
clocks = <&mcbsp4_fck>;
clock-names = "fck";
#sound-dai-cells = <0>;
status = "disabled";
};
mcbsp5: mcbsp@48096000 {
compatible = "ti,omap3-mcbsp";
reg = <0x48096000 0xff>;
reg-names = "mpu";
interrupts = <27>, /* OCP compliant interrupt */
<81>, /* TX interrupt */
<82>; /* RX interrupt */
interrupt-names = "common", "tx", "rx";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp5";
dmas = <&sdma 21>,
<&sdma 22>;
dma-names = "tx", "rx";
clocks = <&mcbsp5_fck>;
clock-names = "fck";
status = "disabled";
};
sham: sham@480c3000 {
compatible = "ti,omap3-sham";
ti,hwmods = "sham";
reg = <0x480c3000 0x64>;
interrupts = <49>;
dmas = <&sdma 69>;
dma-names = "rx";
};
timer1_target: target-module@48318000 {
compatible = "ti,sysc-omap2-timer", "ti,sysc";
reg = <0x48318000 0x4>,
<0x48318010 0x4>,
<0x48318014 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
SYSC_OMAP2_EMUFREE |
SYSC_OMAP2_ENAWAKEUP |
SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,syss-mask = <1>;
clocks = <&gpt1_fck>, <&gpt1_ick>;
clock-names = "fck", "ick";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x48318000 0x1000>;
timer1: timer@0 {
compatible = "ti,omap3430-timer";
reg = <0x0 0x80>;
clocks = <&gpt1_fck>;
clock-names = "fck";
interrupts = <37>;
ti,timer-alwon;
};
};
timer2_target: target-module@49032000 {
compatible = "ti,sysc-omap2-timer", "ti,sysc";
reg = <0x49032000 0x4>,
<0x49032010 0x4>,
<0x49032014 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
SYSC_OMAP2_EMUFREE |
SYSC_OMAP2_ENAWAKEUP |
SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,syss-mask = <1>;
clocks = <&gpt2_fck>, <&gpt2_ick>;
clock-names = "fck", "ick";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x49032000 0x1000>;
timer2: timer@0 {
compatible = "ti,omap3430-timer";
reg = <0 0x400>;
interrupts = <38>;
};
};
timer3: timer@49034000 {
compatible = "ti,omap3430-timer";
reg = <0x49034000 0x400>;
interrupts = <39>;
ti,hwmods = "timer3";
};
timer4: timer@49036000 {
compatible = "ti,omap3430-timer";
reg = <0x49036000 0x400>;
interrupts = <40>;
ti,hwmods = "timer4";
};
timer5: timer@49038000 {
compatible = "ti,omap3430-timer";
reg = <0x49038000 0x400>;
interrupts = <41>;
ti,hwmods = "timer5";
ti,timer-dsp;
};
timer6: timer@4903a000 {
compatible = "ti,omap3430-timer";
reg = <0x4903a000 0x400>;
interrupts = <42>;
ti,hwmods = "timer6";
ti,timer-dsp;
};
timer7: timer@4903c000 {
compatible = "ti,omap3430-timer";
reg = <0x4903c000 0x400>;
interrupts = <43>;
ti,hwmods = "timer7";
ti,timer-dsp;
};
timer8: timer@4903e000 {
compatible = "ti,omap3430-timer";
reg = <0x4903e000 0x400>;
interrupts = <44>;
ti,hwmods = "timer8";
ti,timer-pwm;
ti,timer-dsp;
};
timer9: timer@49040000 {
compatible = "ti,omap3430-timer";
reg = <0x49040000 0x400>;
interrupts = <45>;
ti,hwmods = "timer9";
ti,timer-pwm;
};
timer10: timer@48086000 {
compatible = "ti,omap3430-timer";
reg = <0x48086000 0x400>;
interrupts = <46>;
ti,hwmods = "timer10";
ti,timer-pwm;
};
timer11: timer@48088000 {
compatible = "ti,omap3430-timer";
reg = <0x48088000 0x400>;
interrupts = <47>;
ti,hwmods = "timer11";
ti,timer-pwm;
};
timer12_target: target-module@48304000 {
compatible = "ti,sysc-omap2-timer", "ti,sysc";
reg = <0x48304000 0x4>,
<0x48304010 0x4>,
<0x48304014 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
SYSC_OMAP2_EMUFREE |
SYSC_OMAP2_ENAWAKEUP |
SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,syss-mask = <1>;
clocks = <&gpt12_fck>, <&gpt12_ick>;
clock-names = "fck", "ick";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x48304000 0x1000>;
timer12: timer@0 {
compatible = "ti,omap3430-timer";
reg = <0 0x400>;
interrupts = <95>;
ti,timer-alwon;
ti,timer-secure;
};
};
usbhstll: usbhstll@48062000 {
compatible = "ti,usbhs-tll";
reg = <0x48062000 0x1000>;
interrupts = <78>;
ti,hwmods = "usb_tll_hs";
};
usbhshost: usbhshost@48064000 {
compatible = "ti,usbhs-host";
reg = <0x48064000 0x400>;
ti,hwmods = "usb_host_hs";
#address-cells = <1>;
#size-cells = <1>;
ranges;
usbhsohci: ohci@48064400 {
compatible = "ti,ohci-omap3";
reg = <0x48064400 0x400>;
interrupts = <76>;
remote-wakeup-connected;
};
usbhsehci: ehci@48064800 {
compatible = "ti,ehci-omap";
reg = <0x48064800 0x400>;
interrupts = <77>;
};
};
gpmc: gpmc@6e000000 {
compatible = "ti,omap3430-gpmc";
ti,hwmods = "gpmc";
reg = <0x6e000000 0x02d0>;
interrupts = <20>;
dmas = <&sdma 4>;
dma-names = "rxtx";
gpmc,num-cs = <8>;
gpmc,num-waitpins = <4>;
#address-cells = <2>;
#size-cells = <1>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
};
usb_otg_target: target-module@480ab000 {
compatible = "ti,sysc-omap2", "ti,sysc";
reg = <0x480ab400 0x4>,
<0x480ab404 0x4>,
<0x480ab408 0x4>;
reg-names = "rev", "sysc", "syss";
ti,sysc-mask = <(SYSC_OMAP2_ENAWAKEUP |
SYSC_OMAP2_SOFTRESET |
SYSC_OMAP2_AUTOIDLE)>;
ti,sysc-midle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,syss-mask = <1>;
/* Clock defined in the SoC specific dtsi file */
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x480ab000 0x1000>;
usb_otg_hs: usb@0 {
compatible = "ti,omap3-musb";
reg = <0 0x1000>;
interrupts = <92>, <93>;
interrupt-names = "mc", "dma";
multipoint = <1>;
num-eps = <16>;
ram-bits = <12>;
};
};
dss: dss@48050000 {
compatible = "ti,omap3-dss";
reg = <0x48050000 0x200>;
status = "disabled";
ti,hwmods = "dss_core";
clocks = <&dss1_alwon_fck>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges;
dispc@48050400 {
compatible = "ti,omap3-dispc";
reg = <0x48050400 0x400>;
interrupts = <25>;
ti,hwmods = "dss_dispc";
clocks = <&dss1_alwon_fck>;
clock-names = "fck";
};
dsi: encoder@4804fc00 {
compatible = "ti,omap3-dsi";
reg = <0x4804fc00 0x200>,
<0x4804fe00 0x40>,
<0x4804ff00 0x20>;
reg-names = "proto", "phy", "pll";
interrupts = <25>;
status = "disabled";
ti,hwmods = "dss_dsi1";
clocks = <&dss1_alwon_fck>, <&dss2_alwon_fck>;
clock-names = "fck", "sys_clk";
#address-cells = <1>;
#size-cells = <0>;
};
rfbi: encoder@48050800 {
compatible = "ti,omap3-rfbi";
reg = <0x48050800 0x100>;
status = "disabled";
ti,hwmods = "dss_rfbi";
clocks = <&dss1_alwon_fck>, <&dss_ick>;
clock-names = "fck", "ick";
};
venc: encoder@48050c00 {
compatible = "ti,omap3-venc";
reg = <0x48050c00 0x100>;
status = "disabled";
ti,hwmods = "dss_venc";
clocks = <&dss_tv_fck>;
clock-names = "fck";
};
};
ssi: ssi-controller@48058000 {
compatible = "ti,omap3-ssi";
ti,hwmods = "ssi";
status = "disabled";
reg = <0x48058000 0x1000>,
<0x48059000 0x1000>;
reg-names = "sys",
"gdd";
interrupts = <71>;
interrupt-names = "gdd_mpu";
#address-cells = <1>;
#size-cells = <1>;
ranges;
ssi_port1: ssi-port@4805a000 {
compatible = "ti,omap3-ssi-port";
reg = <0x4805a000 0x800>,
<0x4805a800 0x800>;
reg-names = "tx",
"rx";
interrupts = <67>,
<68>;
};
ssi_port2: ssi-port@4805b000 {
compatible = "ti,omap3-ssi-port";
reg = <0x4805b000 0x800>,
<0x4805b800 0x800>;
reg-names = "tx",
"rx";
interrupts = <69>,
<70>;
};
};
};
};
#include "omap3xxx-clocks.dtsi"
/* Preferred always-on timer for clockevent. Some boards must use dmtimer12 */
&timer1_target {
ti,no-reset-on-init;
ti,no-idle;
timer@0 {
assigned-clocks = <&gpt1_fck>;
assigned-clock-parents = <&omap_32k_fck>;
};
};