/* SPDX-License-Identifier: GPL-2.0 */
/*
* Octeon HCD hardware register definitions.
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*
* Some parts of the code were originally released under BSD license:
*
* Copyright (c) 2003-2010 Cavium Networks (support@cavium.com). All rights
* reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are
* met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
*
* * Redistributions in binary form must reproduce the above
* copyright notice, this list of conditions and the following
* disclaimer in the documentation and/or other materials provided
* with the distribution.
*
* * Neither the name of Cavium Networks nor the names of
* its contributors may be used to endorse or promote products
* derived from this software without specific prior written
* permission.
*
* This Software, including technical data, may be subject to U.S. export
* control laws, including the U.S. Export Administration Act and its associated
* regulations, and may be subject to export or import regulations in other
* countries.
*
* TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE SOFTWARE IS PROVIDED "AS IS"
* AND WITH ALL FAULTS AND CAVIUM NETWORKS MAKES NO PROMISES, REPRESENTATIONS OR
* WARRANTIES, EITHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, WITH RESPECT TO
* THE SOFTWARE, INCLUDING ITS CONDITION, ITS CONFORMITY TO ANY REPRESENTATION
* OR DESCRIPTION, OR THE EXISTENCE OF ANY LATENT OR PATENT DEFECTS, AND CAVIUM
* SPECIFICALLY DISCLAIMS ALL IMPLIED (IF ANY) WARRANTIES OF TITLE,
* MERCHANTABILITY, NONINFRINGEMENT, FITNESS FOR A PARTICULAR PURPOSE, LACK OF
* VIRUSES, ACCURACY OR COMPLETENESS, QUIET ENJOYMENT, QUIET POSSESSION OR
* CORRESPONDENCE TO DESCRIPTION. THE ENTIRE RISK ARISING OUT OF USE OR
* PERFORMANCE OF THE SOFTWARE LIES WITH YOU.
*/
#ifndef __OCTEON_HCD_H__
#define __OCTEON_HCD_H__
#include <asm/bitfield.h>
#define CVMX_USBCXBASE 0x00016F0010000000ull
#define CVMX_USBCXREG1(reg, bid) \
(CVMX_ADD_IO_SEG(CVMX_USBCXBASE | reg) + \
((bid) & 1) * 0x100000000000ull)
#define CVMX_USBCXREG2(reg, bid, off) \
(CVMX_ADD_IO_SEG(CVMX_USBCXBASE | reg) + \
(((off) & 7) + ((bid) & 1) * 0x8000000000ull) * 32)
#define CVMX_USBCX_GAHBCFG(bid) CVMX_USBCXREG1(0x008, bid)
#define CVMX_USBCX_GHWCFG3(bid) CVMX_USBCXREG1(0x04c, bid)
#define CVMX_USBCX_GINTMSK(bid) CVMX_USBCXREG1(0x018, bid)
#define CVMX_USBCX_GINTSTS(bid) CVMX_USBCXREG1(0x014, bid)
#define CVMX_USBCX_GNPTXFSIZ(bid) CVMX_USBCXREG1(0x028, bid)
#define CVMX_USBCX_GNPTXSTS(bid) CVMX_USBCXREG1(0x02c, bid)
#define CVMX_USBCX_GOTGCTL(bid) CVMX_USBCXREG1(0x000, bid)
#define CVMX_USBCX_GRSTCTL(bid) CVMX_USBCXREG1(0x010, bid)
#define CVMX_USBCX_GRXFSIZ(bid) CVMX_USBCXREG1(0x024, bid)
#define CVMX_USBCX_GRXSTSPH(bid) CVMX_USBCXREG1(0x020, bid)
#define CVMX_USBCX_GUSBCFG(bid) CVMX_USBCXREG1(0x00c, bid)
#define CVMX_USBCX_HAINT(bid) CVMX_USBCXREG1(0x414, bid)
#define CVMX_USBCX_HAINTMSK(bid) CVMX_USBCXREG1(0x418, bid)
#define CVMX_USBCX_HCCHARX(off, bid) CVMX_USBCXREG2(0x500, bid, off)
#define CVMX_USBCX_HCFG(bid) CVMX_USBCXREG1(0x400, bid)
#define CVMX_USBCX_HCINTMSKX(off, bid) CVMX_USBCXREG2(0x50c, bid, off)
#define CVMX_USBCX_HCINTX(off, bid) CVMX_USBCXREG2(0x508, bid, off)
#define CVMX_USBCX_HCSPLTX(off, bid) CVMX_USBCXREG2(0x504, bid, off)
#define CVMX_USBCX_HCTSIZX(off, bid) CVMX_USBCXREG2(0x510, bid, off)
#define CVMX_USBCX_HFIR(bid) CVMX_USBCXREG1(0x404, bid)
#define CVMX_USBCX_HFNUM(bid) CVMX_USBCXREG1(0x408, bid)
#define CVMX_USBCX_HPRT(bid) CVMX_USBCXREG1(0x440, bid)
#define CVMX_USBCX_HPTXFSIZ(bid) CVMX_USBCXREG1(0x100, bid)
#define CVMX_USBCX_HPTXSTS(bid) CVMX_USBCXREG1(0x410, bid)
#define CVMX_USBNXBID1(bid) (((bid) & 1) * 0x10000000ull)
#define CVMX_USBNXBID2(bid) (((bid) & 1) * 0x100000000000ull)
#define CVMX_USBNXREG1(reg, bid) \
(CVMX_ADD_IO_SEG(0x0001180068000000ull | reg) + CVMX_USBNXBID1(bid))
#define CVMX_USBNXREG2(reg, bid) \
(CVMX_ADD_IO_SEG(0x00016F0000000000ull | reg) + CVMX_USBNXBID2(bid))
#define CVMX_USBNX_CLK_CTL(bid) CVMX_USBNXREG1(0x10, bid)
#define CVMX_USBNX_DMA0_INB_CHN0(bid) CVMX_USBNXREG2(0x818, bid)
#define CVMX_USBNX_DMA0_OUTB_CHN0(bid) CVMX_USBNXREG2(0x858, bid)
#define CVMX_USBNX_USBP_CTL_STATUS(bid) CVMX_USBNXREG1(0x18, bid)
/**
* cvmx_usbc#_gahbcfg
*
* Core AHB Configuration Register (GAHBCFG)
*
* This register can be used to configure the core after power-on or a change in
* mode of operation. This register mainly contains AHB system-related
* configuration parameters. The AHB is the processor interface to the O2P USB
* core. In general, software need not know about this interface except to
* program the values as specified.
*
* The application must program this register as part of the O2P USB core
* initialization. Do not change this register after the initial programming.
*/
union cvmx_usbcx_gahbcfg {
u32 u32;
/**
* struct cvmx_usbcx_gahbcfg_s
* @ptxfemplvl: Periodic TxFIFO Empty Level (PTxFEmpLvl)
* Software should set this bit to 0x1.
* Indicates when the Periodic TxFIFO Empty Interrupt bit in the
* Core Interrupt register (GINTSTS.PTxFEmp) is triggered. This
* bit is used only in Slave mode.
* * 1'b0: GINTSTS.PTxFEmp interrupt indicates that the Periodic
* TxFIFO is half empty
* * 1'b1: GINTSTS.PTxFEmp interrupt indicates that the Periodic
* TxFIFO is completely empty
* @nptxfemplvl: Non-Periodic TxFIFO Empty Level (NPTxFEmpLvl)
* Software should set this bit to 0x1.
* Indicates when the Non-Periodic TxFIFO Empty Interrupt bit in
* the Core Interrupt register (GINTSTS.NPTxFEmp) is triggered.
* This bit is used only in Slave mode.
* * 1'b0: GINTSTS.NPTxFEmp interrupt indicates that the Non-
* Periodic TxFIFO is half empty
* * 1'b1: GINTSTS.NPTxFEmp interrupt indicates that the Non-
* Periodic TxFIFO is completely empty
* @dmaen: DMA Enable (DMAEn)
* * 1'b0: Core operates in Slave mode
* * 1'b1: Core operates in a DMA mode
* @hbstlen: Burst Length/Type (HBstLen)
* This field has not effect and should be left as 0x0.
* @glblintrmsk: Global Interrupt Mask (GlblIntrMsk)
* Software should set this field to 0x1.
* The application uses this bit to mask or unmask the interrupt
* line assertion to itself. Irrespective of this bit's setting,
* the interrupt status registers are updated by the core.
* * 1'b0: Mask the interrupt assertion to the application.
* * 1'b1: Unmask the interrupt assertion to the application.
*/
struct cvmx_usbcx_gahbcfg_s {
__BITFIELD_FIELD(u32 reserved_9_31 : 23,
__BITFIELD_FIELD(u32 ptxfemplvl : 1,
__BITFIELD_FIELD(u32 nptxfemplvl : 1,
__BITFIELD_FIELD(u32 reserved_6_6 : 1,
__BITFIELD_FIELD(u32 dmaen : 1,
__BITFIELD_FIELD(u32 hbstlen : 4,
__BITFIELD_FIELD(u32 glblintrmsk : 1,
;)))))))
} s;
};
/**
* cvmx_usbc#_ghwcfg3
*
* User HW Config3 Register (GHWCFG3)
*
* This register contains the configuration options of the O2P USB core.
*/
union cvmx_usbcx_ghwcfg3 {
u32 u32;
/**
* struct cvmx_usbcx_ghwcfg3_s
* @dfifodepth: DFIFO Depth (DfifoDepth)
* This value is in terms of 32-bit words.
* * Minimum value is 32
* * Maximum value is 32768
* @ahbphysync: AHB and PHY Synchronous (AhbPhySync)
* Indicates whether AHB and PHY clocks are synchronous to
* each other.
* * 1'b0: No
* * 1'b1: Yes
* This bit is tied to 1.
* @rsttype: Reset Style for Clocked always Blocks in RTL (RstType)
* * 1'b0: Asynchronous reset is used in the core
* * 1'b1: Synchronous reset is used in the core
* @optfeature: Optional Features Removed (OptFeature)
* Indicates whether the User ID register, GPIO interface ports,
* and SOF toggle and counter ports were removed for gate count
* optimization.
* @vendor_control_interface_support: Vendor Control Interface Support
* * 1'b0: Vendor Control Interface is not available on the core.
* * 1'b1: Vendor Control Interface is available.
* @i2c_selection: I2C Selection
* * 1'b0: I2C Interface is not available on the core.
* * 1'b1: I2C Interface is available on the core.
* @otgen: OTG Function Enabled (OtgEn)
* The application uses this bit to indicate the O2P USB core's
* OTG capabilities.
* * 1'b0: Not OTG capable
* * 1'b1: OTG Capable
* @pktsizewidth: Width of Packet Size Counters (PktSizeWidth)
* * 3'b000: 4 bits
* * 3'b001: 5 bits
* * 3'b010: 6 bits
* * 3'b011: 7 bits
* * 3'b100: 8 bits
* * 3'b101: 9 bits
* * 3'b110: 10 bits
* * Others: Reserved
* @xfersizewidth: Width of Transfer Size Counters (XferSizeWidth)
* * 4'b0000: 11 bits
* * 4'b0001: 12 bits
* - ...
* * 4'b1000: 19 bits
* * Others: Reserved
*/
struct cvmx_usbcx_ghwcfg3_s {
__BITFIELD_FIELD(u32 dfifodepth : 16,
__BITFIELD_FIELD(u32 reserved_13_15 : 3,
__BITFIELD_FIELD(u32 ahbphysync : 1,
__BITFIELD_FIELD(u32 rsttype : 1,
__BITFIELD_FIELD(u32 optfeature : 1,
__BITFIELD_FIELD(u32 vendor_control_interface_support : 1,
__BITFIELD_FIELD(u32 i2c_selection : 1,
__BITFIELD_FIELD(u32 otgen : 1,
__BITFIELD_FIELD(u32 pktsizewidth : 3,
__BITFIELD_FIELD(u32 xfersizewidth : 4,
;))))))))))
} s;
};
/**
* cvmx_usbc#_gintmsk
*
* Core Interrupt Mask Register (GINTMSK)
*
* This register works with the Core Interrupt register to interrupt the
* application. When an interrupt bit is masked, the interrupt associated with
* that bit will not be generated. However, the Core Interrupt (GINTSTS)
* register bit corresponding to that interrupt will still be set.
* Mask interrupt: 1'b0, Unmask interrupt: 1'b1
*/
union cvmx_usbcx_gintmsk {
u32 u32;
/**
* struct cvmx_usbcx_gintmsk_s
* @wkupintmsk: Resume/Remote Wakeup Detected Interrupt Mask
* (WkUpIntMsk)
* @sessreqintmsk: Session Request/New Session Detected Interrupt Mask
* (SessReqIntMsk)
* @disconnintmsk: Disconnect Detected Interrupt Mask (DisconnIntMsk)
* @conidstschngmsk: Connector ID Status Change Mask (ConIDStsChngMsk)
* @ptxfempmsk: Periodic TxFIFO Empty Mask (PTxFEmpMsk)
* @hchintmsk: Host Channels Interrupt Mask (HChIntMsk)
* @prtintmsk: Host Port Interrupt Mask (PrtIntMsk)
* @fetsuspmsk: Data Fetch Suspended Mask (FetSuspMsk)
* @incomplpmsk: Incomplete Periodic Transfer Mask (incomplPMsk)
* Incomplete Isochronous OUT Transfer Mask
* (incompISOOUTMsk)
* @incompisoinmsk: Incomplete Isochronous IN Transfer Mask
* (incompISOINMsk)
* @oepintmsk: OUT Endpoints Interrupt Mask (OEPIntMsk)
* @inepintmsk: IN Endpoints Interrupt Mask (INEPIntMsk)
* @epmismsk: Endpoint Mismatch Interrupt Mask (EPMisMsk)
* @eopfmsk: End of Periodic Frame Interrupt Mask (EOPFMsk)
* @isooutdropmsk: Isochronous OUT Packet Dropped Interrupt Mask
* (ISOOutDropMsk)
* @enumdonemsk: Enumeration Done Mask (EnumDoneMsk)
* @usbrstmsk: USB Reset Mask (USBRstMsk)
* @usbsuspmsk: USB Suspend Mask (USBSuspMsk)
* @erlysuspmsk: Early Suspend Mask (ErlySuspMsk)
* @i2cint: I2C Interrupt Mask (I2CINT)
* @ulpickintmsk: ULPI Carkit Interrupt Mask (ULPICKINTMsk)
* I2C Carkit Interrupt Mask (I2CCKINTMsk)
* @goutnakeffmsk: Global OUT NAK Effective Mask (GOUTNakEffMsk)
* @ginnakeffmsk: Global Non-Periodic IN NAK Effective Mask
* (GINNakEffMsk)
* @nptxfempmsk: Non-Periodic TxFIFO Empty Mask (NPTxFEmpMsk)
* @rxflvlmsk: Receive FIFO Non-Empty Mask (RxFLvlMsk)
* @sofmsk: Start of (micro)Frame Mask (SofMsk)
* @otgintmsk: OTG Interrupt Mask (OTGIntMsk)
* @modemismsk: Mode Mismatch Interrupt Mask (ModeMisMsk)
*/
struct cvmx_usbcx_gintmsk_s {
__BITFIELD_FIELD(u32 wkupintmsk : 1,
__BITFIELD_FIELD(u32 sessreqintmsk : 1,
__BITFIELD_FIELD(u32 disconnintmsk : 1,
__BITFIELD_FIELD(u32 conidstschngmsk : 1,
__BITFIELD_FIELD(u32 reserved_27_27 : 1,
__BITFIELD_FIELD(u32 ptxfempmsk : 1,
__BITFIELD_FIELD(u32 hchintmsk : 1,
__BITFIELD_FIELD(u32 prtintmsk : 1,
__BITFIELD_FIELD(u32 reserved_23_23 : 1,
__BITFIELD_FIELD(u32 fetsuspmsk : 1,
__BITFIELD_FIELD(u32 incomplpmsk : 1,
__BITFIELD_FIELD(u32 incompisoinmsk : 1,
__BITFIELD_FIELD(u32 oepintmsk : 1,
__BITFIELD_FIELD(u32 inepintmsk : 1,
__BITFIELD_FIELD(u32 epmismsk : 1,
__BITFIELD_FIELD(u32 reserved_16_16 : 1,
__BITFIELD_FIELD(u32 eopfmsk : 1,
__BITFIELD_FIELD(u32 isooutdropmsk : 1,
__BITFIELD_FIELD(u32 enumdonemsk : 1,
__BITFIELD_FIELD(u32 usbrstmsk : 1,
__BITFIELD_FIELD(u32 usbsuspmsk : 1,
__BITFIELD_FIELD(u32 erlysuspmsk : 1,
__BITFIELD_FIELD(u32 i2cint : 1,
__BITFIELD_FIELD(u32 ulpickintmsk : 1,
__BITFIELD_FIELD(u32 goutnakeffmsk : 1,
__BITFIELD_FIELD(u32 ginnakeffmsk : 1,
__BITFIELD_FIELD(u32 nptxfempmsk : 1,
__BITFIELD_FIELD(u32 rxflvlmsk : 1,
__BITFIELD_FIELD(u32 sofmsk : 1,
__BITFIELD_FIELD(u32 otgintmsk : 1,
__BITFIELD_FIELD(u32 modemismsk : 1,
__BITFIELD_FIELD(u32 reserved_0_0 : 1,
;))))))))))))))))))))))))))))))))
} s;
};
/**
* cvmx_usbc#_gintsts
*
* Core Interrupt Register (GINTSTS)
*
* This register interrupts the application for system-level events in the
* current mode of operation (Device mode or Host mode). It is shown in
* Interrupt. Some of the bits in this register are valid only in Host mode,
* while others are valid in Device mode only. This register also indicates the
* current mode of operation. In order to clear the interrupt status bits of
* type R_SS_WC, the application must write 1'b1 into the bit. The FIFO status
* interrupts are read only; once software reads from or writes to the FIFO
* while servicing these interrupts, FIFO interrupt conditions are cleared
* automatically.
*/
union cvmx_usbcx_gintsts {
u32 u32;
/**
* struct cvmx_usbcx_gintsts_s
* @wkupint: Resume/Remote Wakeup Detected Interrupt (WkUpInt)
* In Device mode, this interrupt is asserted when a resume is
* detected on the USB. In Host mode, this interrupt is asserted
* when a remote wakeup is detected on the USB.
* For more information on how to use this interrupt, see "Partial
* Power-Down and Clock Gating Programming Model" on
* page 353.
* @sessreqint: Session Request/New Session Detected Interrupt
* (SessReqInt)
* In Host mode, this interrupt is asserted when a session request
* is detected from the device. In Device mode, this interrupt is
* asserted when the utmiotg_bvalid signal goes high.
* For more information on how to use this interrupt, see "Partial
* Power-Down and Clock Gating Programming Model" on
* page 353.
* @disconnint: Disconnect Detected Interrupt (DisconnInt)
* Asserted when a device disconnect is detected.
* @conidstschng: Connector ID Status Change (ConIDStsChng)
* The core sets this bit when there is a change in connector ID
* status.
* @ptxfemp: Periodic TxFIFO Empty (PTxFEmp)
* Asserted when the Periodic Transmit FIFO is either half or
* completely empty and there is space for at least one entry to be
* written in the Periodic Request Queue. The half or completely
* empty status is determined by the Periodic TxFIFO Empty Level
* bit in the Core AHB Configuration register
* (GAHBCFG.PTxFEmpLvl).
* @hchint: Host Channels Interrupt (HChInt)
* The core sets this bit to indicate that an interrupt is pending
* on one of the channels of the core (in Host mode). The
* application must read the Host All Channels Interrupt (HAINT)
* register to determine the exact number of the channel on which
* the interrupt occurred, and then read the corresponding Host
* Channel-n Interrupt (HCINTn) register to determine the exact
* cause of the interrupt. The application must clear the
* appropriate status bit in the HCINTn register to clear this bit.
* @prtint: Host Port Interrupt (PrtInt)
* The core sets this bit to indicate a change in port status of
* one of the O2P USB core ports in Host mode. The application must
* read the Host Port Control and Status (HPRT) register to
* determine the exact event that caused this interrupt. The
* application must clear the appropriate status bit in the Host
* Port Control and Status register to clear this bit.
* @fetsusp: Data Fetch Suspended (FetSusp)
* This interrupt is valid only in DMA mode. This interrupt
* indicates that the core has stopped fetching data for IN
* endpoints due to the unavailability of TxFIFO space or Request
* Queue space. This interrupt is used by the application for an
* endpoint mismatch algorithm.
* @incomplp: Incomplete Periodic Transfer (incomplP)
* In Host mode, the core sets this interrupt bit when there are
* incomplete periodic transactions still pending which are
* scheduled for the current microframe.
* Incomplete Isochronous OUT Transfer (incompISOOUT)
* The Device mode, the core sets this interrupt to indicate that
* there is at least one isochronous OUT endpoint on which the
* transfer is not completed in the current microframe. This
* interrupt is asserted along with the End of Periodic Frame
* Interrupt (EOPF) bit in this register.
* @incompisoin: Incomplete Isochronous IN Transfer (incompISOIN)
* The core sets this interrupt to indicate that there is at least
* one isochronous IN endpoint on which the transfer is not
* completed in the current microframe. This interrupt is asserted
* along with the End of Periodic Frame Interrupt (EOPF) bit in
* this register.
* @oepint: OUT Endpoints Interrupt (OEPInt)
* The core sets this bit to indicate that an interrupt is pending
* on one of the OUT endpoints of the core (in Device mode). The
* application must read the Device All Endpoints Interrupt
* (DAINT) register to determine the exact number of the OUT
* endpoint on which the interrupt occurred, and then read the
* corresponding Device OUT Endpoint-n Interrupt (DOEPINTn)
* register to determine the exact cause of the interrupt. The
* application must clear the appropriate status bit in the
* corresponding DOEPINTn register to clear this bit.
* @iepint: IN Endpoints Interrupt (IEPInt)
* The core sets this bit to indicate that an interrupt is pending
* on one of the IN endpoints of the core (in Device mode). The
* application must read the Device All Endpoints Interrupt
* (DAINT) register to determine the exact number of the IN
* endpoint on which the interrupt occurred, and then read the
* corresponding Device IN Endpoint-n Interrupt (DIEPINTn)
* register to determine the exact cause of the interrupt. The
* application must clear the appropriate status bit in the
* corresponding DIEPINTn register to clear this bit.
* @epmis: Endpoint Mismatch Interrupt (EPMis)
* Indicates that an IN token has been received for a non-periodic
* endpoint, but the data for another endpoint is present in the
* top of the Non-Periodic Transmit FIFO and the IN endpoint
* mismatch count programmed by the application has expired.
* @eopf: End of Periodic Frame Interrupt (EOPF)
* Indicates that the period specified in the Periodic Frame
* Interval field of the Device Configuration register
* (DCFG.PerFrInt) has been reached in the current microframe.
* @isooutdrop: Isochronous OUT Packet Dropped Interrupt (ISOOutDrop)
* The core sets this bit when it fails to write an isochronous OUT
* packet into the RxFIFO because the RxFIFO doesn't have
* enough space to accommodate a maximum packet size packet
* for the isochronous OUT endpoint.
* @enumdone: Enumeration Done (EnumDone)
* The core sets this bit to indicate that speed enumeration is
* complete. The application must read the Device Status (DSTS)
* register to obtain the enumerated speed.
* @usbrst: USB Reset (USBRst)
* The core sets this bit to indicate that a reset is detected on
* the USB.
* @usbsusp: USB Suspend (USBSusp)
* The core sets this bit to indicate that a suspend was detected
* on the USB. The core enters the Suspended state when there
* is no activity on the phy_line_state_i signal for an extended
* period of time.
* @erlysusp: Early Suspend (ErlySusp)
* The core sets this bit to indicate that an Idle state has been
* detected on the USB for 3 ms.
* @i2cint: I2C Interrupt (I2CINT)
* This bit is always 0x0.
* @ulpickint: ULPI Carkit Interrupt (ULPICKINT)
* This bit is always 0x0.
* @goutnakeff: Global OUT NAK Effective (GOUTNakEff)
* Indicates that the Set Global OUT NAK bit in the Device Control
* register (DCTL.SGOUTNak), set by the application, has taken
* effect in the core. This bit can be cleared by writing the Clear
* Global OUT NAK bit in the Device Control register
* (DCTL.CGOUTNak).
* @ginnakeff: Global IN Non-Periodic NAK Effective (GINNakEff)
* Indicates that the Set Global Non-Periodic IN NAK bit in the
* Device Control register (DCTL.SGNPInNak), set by the
* application, has taken effect in the core. That is, the core has
* sampled the Global IN NAK bit set by the application. This bit
* can be cleared by clearing the Clear Global Non-Periodic IN
* NAK bit in the Device Control register (DCTL.CGNPInNak).
* This interrupt does not necessarily mean that a NAK handshake
* is sent out on the USB. The STALL bit takes precedence over
* the NAK bit.
* @nptxfemp: Non-Periodic TxFIFO Empty (NPTxFEmp)
* This interrupt is asserted when the Non-Periodic TxFIFO is
* either half or completely empty, and there is space for at least
* one entry to be written to the Non-Periodic Transmit Request
* Queue. The half or completely empty status is determined by
* the Non-Periodic TxFIFO Empty Level bit in the Core AHB
* Configuration register (GAHBCFG.NPTxFEmpLvl).
* @rxflvl: RxFIFO Non-Empty (RxFLvl)
* Indicates that there is at least one packet pending to be read
* from the RxFIFO.
* @sof: Start of (micro)Frame (Sof)
* In Host mode, the core sets this bit to indicate that an SOF
* (FS), micro-SOF (HS), or Keep-Alive (LS) is transmitted on the
* USB. The application must write a 1 to this bit to clear the
* interrupt.
* In Device mode, in the core sets this bit to indicate that an
* SOF token has been received on the USB. The application can read
* the Device Status register to get the current (micro)frame
* number. This interrupt is seen only when the core is operating
* at either HS or FS.
* @otgint: OTG Interrupt (OTGInt)
* The core sets this bit to indicate an OTG protocol event. The
* application must read the OTG Interrupt Status (GOTGINT)
* register to determine the exact event that caused this
* interrupt. The application must clear the appropriate status bit
* in the GOTGINT register to clear this bit.
* @modemis: Mode Mismatch Interrupt (ModeMis)
* The core sets this bit when the application is trying to access:
* * A Host mode register, when the core is operating in Device
* mode
* * A Device mode register, when the core is operating in Host
* mode
* The register access is completed on the AHB with an OKAY
* response, but is ignored by the core internally and doesn't
* affect the operation of the core.
* @curmod: Current Mode of Operation (CurMod)
* Indicates the current mode of operation.
* * 1'b0: Device mode
* * 1'b1: Host mode
*/
struct cvmx_usbcx_gintsts_s {
__BITFIELD_FIELD(u32 wkupint : 1,
__BITFIELD_FIELD(u32 sessreqint : 1,
__BITFIELD_FIELD(u32 disconnint : 1,
__BITFIELD_FIELD(u32 conidstschng : 1,
__BITFIELD_FIELD(u32 reserved_27_27 : 1,
__BITFIELD_FIELD(u32 ptxfemp : 1,
__BITFIELD_FIELD(u32 hchint : 1,
__BITFIELD_FIELD(u32 prtint : 1,
__BITFIELD_FIELD(u32 reserved_23_23 : 1,
__BITFIELD_FIELD(u32 fetsusp : 1,
__BITFIELD_FIELD(u32 incomplp : 1,
__BITFIELD_FIELD(u32 incompisoin : 1,
__BITFIELD_FIELD(u32 oepint : 1,
__BITFIELD_FIELD(u32 iepint : 1,
__BITFIELD_FIELD(u32 epmis : 1,
__BITFIELD_FIELD(u32 reserved_16_16 : 1,
__BITFIELD_FIELD(u32 eopf : 1,
__BITFIELD_FIELD(u32 isooutdrop : 1,
__BITFIELD_FIELD(u32 enumdone : 1,
__BITFIELD_FIELD(u32 usbrst : 1,
__BITFIELD_FIELD(u32 usbsusp : 1,
__BITFIELD_FIELD(u32 erlysusp : 1,
__BITFIELD_FIELD(u32 i2cint : 1,
__BITFIELD_FIELD(u32 ulpickint : 1,
__BITFIELD_FIELD(u32 goutnakeff : 1,
__BITFIELD_FIELD(u32 ginnakeff : 1,
__BITFIELD_FIELD(u32 nptxfemp : 1,
__BITFIELD_FIELD(u32 rxflvl : 1,
__BITFIELD_FIELD(u32 sof : 1,
__BITFIELD_FIELD(u32 otgint : 1,
__BITFIELD_FIELD(u32 modemis : 1,
__BITFIELD_FIELD(u32 curmod : 1,
;))))))))))))))))))))))))))))))))
} s;
};
/**
* cvmx_usbc#_gnptxfsiz
*
* Non-Periodic Transmit FIFO Size Register (GNPTXFSIZ)
*
* The application can program the RAM size and the memory start address for the
* Non-Periodic TxFIFO.
*/
union cvmx_usbcx_gnptxfsiz {
u32 u32;
/**
* struct cvmx_usbcx_gnptxfsiz_s
* @nptxfdep: Non-Periodic TxFIFO Depth (NPTxFDep)
* This value is in terms of 32-bit words.
* Minimum value is 16
* Maximum value is 32768
* @nptxfstaddr: Non-Periodic Transmit RAM Start Address (NPTxFStAddr)
* This field contains the memory start address for Non-Periodic
* Transmit FIFO RAM.
*/
struct cvmx_usbcx_gnptxfsiz_s {
__BITFIELD_FIELD(u32 nptxfdep : 16,
__BITFIELD_FIELD(u32 nptxfstaddr : 16,
;))
} s;
};
/**
* cvmx_usbc#_gnptxsts
*
* Non-Periodic Transmit FIFO/Queue Status Register (GNPTXSTS)
*
* This read-only register contains the free space information for the
* Non-Periodic TxFIFO and the Non-Periodic Transmit Request Queue.
*/
union cvmx_usbcx_gnptxsts {
u32 u32;
/**
* struct cvmx_usbcx_gnptxsts_s
* @nptxqtop: Top of the Non-Periodic Transmit Request Queue (NPTxQTop)
* Entry in the Non-Periodic Tx Request Queue that is currently
* being processed by the MAC.
* * Bits [30:27]: Channel/endpoint number
* * Bits [26:25]:
* - 2'b00: IN/OUT token
* - 2'b01: Zero-length transmit packet (device IN/host OUT)
* - 2'b10: PING/CSPLIT token
* - 2'b11: Channel halt command
* * Bit [24]: Terminate (last entry for selected channel/endpoint)
* @nptxqspcavail: Non-Periodic Transmit Request Queue Space Available
* (NPTxQSpcAvail)
* Indicates the amount of free space available in the Non-
* Periodic Transmit Request Queue. This queue holds both IN
* and OUT requests in Host mode. Device mode has only IN
* requests.
* * 8'h0: Non-Periodic Transmit Request Queue is full
* * 8'h1: 1 location available
* * 8'h2: 2 locations available
* * n: n locations available (0..8)
* * Others: Reserved
* @nptxfspcavail: Non-Periodic TxFIFO Space Avail (NPTxFSpcAvail)
* Indicates the amount of free space available in the Non-
* Periodic TxFIFO.
* Values are in terms of 32-bit words.
* * 16'h0: Non-Periodic TxFIFO is full
* * 16'h1: 1 word available
* * 16'h2: 2 words available
* * 16'hn: n words available (where 0..32768)
* * 16'h8000: 32768 words available
* * Others: Reserved
*/
struct cvmx_usbcx_gnptxsts_s {
__BITFIELD_FIELD(u32 reserved_31_31 : 1,
__BITFIELD_FIELD(u32 nptxqtop : 7,
__BITFIELD_FIELD(u32 nptxqspcavail : 8,
__BITFIELD_FIELD(u32 nptxfspcavail : 16,
;))))
} s;
};
/**
* cvmx_usbc#_grstctl
*
* Core Reset Register (GRSTCTL)
*
* The application uses this register to reset various hardware features inside
* the core.
*/
union cvmx_usbcx_grstctl {
u32 u32;
/**
* struct cvmx_usbcx_grstctl_s
* @ahbidle: AHB Master Idle (AHBIdle)
* Indicates that the AHB Master State Machine is in the IDLE
* condition.
* @dmareq: DMA Request Signal (DMAReq)
* Indicates that the DMA request is in progress. Used for debug.
* @txfnum: TxFIFO Number (TxFNum)
* This is the FIFO number that must be flushed using the TxFIFO
* Flush bit. This field must not be changed until the core clears
* the TxFIFO Flush bit.
* * 5'h0: Non-Periodic TxFIFO flush
* * 5'h1: Periodic TxFIFO 1 flush in Device mode or Periodic
* TxFIFO flush in Host mode
* * 5'h2: Periodic TxFIFO 2 flush in Device mode
* - ...
* * 5'hF: Periodic TxFIFO 15 flush in Device mode
* * 5'h10: Flush all the Periodic and Non-Periodic TxFIFOs in the
* core
* @txfflsh: TxFIFO Flush (TxFFlsh)
* This bit selectively flushes a single or all transmit FIFOs, but
* cannot do so if the core is in the midst of a transaction.
* The application must only write this bit after checking that the
* core is neither writing to the TxFIFO nor reading from the
* TxFIFO.
* The application must wait until the core clears this bit before
* performing any operations. This bit takes 8 clocks (of phy_clk
* or hclk, whichever is slower) to clear.
* @rxfflsh: RxFIFO Flush (RxFFlsh)
* The application can flush the entire RxFIFO using this bit, but
* must first ensure that the core is not in the middle of a
* transaction.
* The application must only write to this bit after checking that
* the core is neither reading from the RxFIFO nor writing to the
* RxFIFO.
* The application must wait until the bit is cleared before
* performing any other operations. This bit will take 8 clocks
* (slowest of PHY or AHB clock) to clear.
* @intknqflsh: IN Token Sequence Learning Queue Flush (INTknQFlsh)
* The application writes this bit to flush the IN Token Sequence
* Learning Queue.
* @frmcntrrst: Host Frame Counter Reset (FrmCntrRst)
* The application writes this bit to reset the (micro)frame number
* counter inside the core. When the (micro)frame counter is reset,
* the subsequent SOF sent out by the core will have a
* (micro)frame number of 0.
* @hsftrst: HClk Soft Reset (HSftRst)
* The application uses this bit to flush the control logic in the
* AHB Clock domain. Only AHB Clock Domain pipelines are reset.
* * FIFOs are not flushed with this bit.
* * All state machines in the AHB clock domain are reset to the
* Idle state after terminating the transactions on the AHB,
* following the protocol.
* * CSR control bits used by the AHB clock domain state
* machines are cleared.
* * To clear this interrupt, status mask bits that control the
* interrupt status and are generated by the AHB clock domain
* state machine are cleared.
* * Because interrupt status bits are not cleared, the application
* can get the status of any core events that occurred after it set
* this bit.
* This is a self-clearing bit that the core clears after all
* necessary logic is reset in the core. This may take several
* clocks, depending on the core's current state.
* @csftrst: Core Soft Reset (CSftRst)
* Resets the hclk and phy_clock domains as follows:
* * Clears the interrupts and all the CSR registers except the
* following register bits:
* - PCGCCTL.RstPdwnModule
* - PCGCCTL.GateHclk
* - PCGCCTL.PwrClmp
* - PCGCCTL.StopPPhyLPwrClkSelclk
* - GUSBCFG.PhyLPwrClkSel
* - GUSBCFG.DDRSel
* - GUSBCFG.PHYSel
* - GUSBCFG.FSIntf
* - GUSBCFG.ULPI_UTMI_Sel
* - GUSBCFG.PHYIf
* - HCFG.FSLSPclkSel
* - DCFG.DevSpd
* * All module state machines (except the AHB Slave Unit) are
* reset to the IDLE state, and all the transmit FIFOs and the
* receive FIFO are flushed.
* * Any transactions on the AHB Master are terminated as soon
* as possible, after gracefully completing the last data phase of
* an AHB transfer. Any transactions on the USB are terminated
* immediately.
* The application can write to this bit any time it wants to reset
* the core. This is a self-clearing bit and the core clears this
* bit after all the necessary logic is reset in the core, which
* may take several clocks, depending on the current state of the
* core. Once this bit is cleared software should wait at least 3
* PHY clocks before doing any access to the PHY domain
* (synchronization delay). Software should also should check that
* bit 31 of this register is 1 (AHB Master is IDLE) before
* starting any operation.
* Typically software reset is used during software development
* and also when you dynamically change the PHY selection bits
* in the USB configuration registers listed above. When you
* change the PHY, the corresponding clock for the PHY is
* selected and used in the PHY domain. Once a new clock is
* selected, the PHY domain has to be reset for proper operation.
*/
struct cvmx_usbcx_grstctl_s {
__BITFIELD_FIELD(u32 ahbidle : 1,
__BITFIELD_FIELD(u32 dmareq : 1,
__BITFIELD_FIELD(u32 reserved_11_29 : 19,
__BITFIELD_FIELD(u32 txfnum : 5,
__BITFIELD_FIELD(u32 txfflsh : 1,
__BITFIELD_FIELD(u32 rxfflsh : 1,
__BITFIELD_FIELD(u32 intknqflsh : 1,
__BITFIELD_FIELD(u32 frmcntrrst : 1,
__BITFIELD_FIELD(u32 hsftrst : 1,
__BITFIELD_FIELD(u32 csftrst : 1,
;))))))))))
} s;
};
/**
* cvmx_usbc#_grxfsiz
*
* Receive FIFO Size Register (GRXFSIZ)
*
* The application can program the RAM size that must be allocated to the
* RxFIFO.
*/
union cvmx_usbcx_grxfsiz {
u32 u32;
/**
* struct cvmx_usbcx_grxfsiz_s
* @rxfdep: RxFIFO Depth (RxFDep)
* This value is in terms of 32-bit words.
* * Minimum value is 16
* * Maximum value is 32768
*/
struct cvmx_usbcx_grxfsiz_s {
__BITFIELD_FIELD(u32 reserved_16_31 : 16,
__BITFIELD_FIELD(u32 rxfdep : 16,
;))
} s;
};
/**
* cvmx_usbc#_grxstsph
*
* Receive Status Read and Pop Register, Host Mode (GRXSTSPH)
*
* A read to the Receive Status Read and Pop register returns and additionally
* pops the top data entry out of the RxFIFO.
* This Description is only valid when the core is in Host Mode. For Device Mode
* use USBC_GRXSTSPD instead.
* NOTE: GRXSTSPH and GRXSTSPD are physically the same register and share the
* same offset in the O2P USB core. The offset difference shown in this
* document is for software clarity and is actually ignored by the
* hardware.
*/
union cvmx_usbcx_grxstsph {
u32 u32;
/**
* struct cvmx_usbcx_grxstsph_s
* @pktsts: Packet Status (PktSts)
* Indicates the status of the received packet
* * 4'b0010: IN data packet received
* * 4'b0011: IN transfer completed (triggers an interrupt)
* * 4'b0101: Data toggle error (triggers an interrupt)
* * 4'b0111: Channel halted (triggers an interrupt)
* * Others: Reserved
* @dpid: Data PID (DPID)
* * 2'b00: DATA0
* * 2'b10: DATA1
* * 2'b01: DATA2
* * 2'b11: MDATA
* @bcnt: Byte Count (BCnt)
* Indicates the byte count of the received IN data packet
* @chnum: Channel Number (ChNum)
* Indicates the channel number to which the current received
* packet belongs.
*/
struct cvmx_usbcx_grxstsph_s {
__BITFIELD_FIELD(u32 reserved_21_31 : 11,
__BITFIELD_FIELD(u32 pktsts : 4,
__BITFIELD_FIELD(u32 dpid : 2,
__BITFIELD_FIELD(u32 bcnt : 11,
__BITFIELD_FIELD(u32 chnum : 4,
;)))))
} s;
};
/**
* cvmx_usbc#_gusbcfg
*
* Core USB Configuration Register (GUSBCFG)
*
* This register can be used to configure the core after power-on or a changing
* to Host mode or Device mode. It contains USB and USB-PHY related
* configuration parameters. The application must program this register before
* starting any transactions on either the AHB or the USB. Do not make changes
* to this register after the initial programming.
*/
union cvmx_usbcx_gusbcfg {
u32 u32;
/**
* struct cvmx_usbcx_gusbcfg_s
* @otgi2csel: UTMIFS or I2C Interface Select (OtgI2CSel)
* This bit is always 0x0.
* @phylpwrclksel: PHY Low-Power Clock Select (PhyLPwrClkSel)
* Software should set this bit to 0x0.
* Selects either 480-MHz or 48-MHz (low-power) PHY mode. In
* FS and LS modes, the PHY can usually operate on a 48-MHz
* clock to save power.
* * 1'b0: 480-MHz Internal PLL clock
* * 1'b1: 48-MHz External Clock
* In 480 MHz mode, the UTMI interface operates at either 60 or
* 30-MHz, depending upon whether 8- or 16-bit data width is
* selected. In 48-MHz mode, the UTMI interface operates at 48
* MHz in FS mode and at either 48 or 6 MHz in LS mode
* (depending on the PHY vendor).
* This bit drives the utmi_fsls_low_power core output signal, and
* is valid only for UTMI+ PHYs.
* @usbtrdtim: USB Turnaround Time (USBTrdTim)
* Sets the turnaround time in PHY clocks.
* Specifies the response time for a MAC request to the Packet
* FIFO Controller (PFC) to fetch data from the DFIFO (SPRAM).
* This must be programmed to 0x5.
* @hnpcap: HNP-Capable (HNPCap)
* This bit is always 0x0.
* @srpcap: SRP-Capable (SRPCap)
* This bit is always 0x0.
* @ddrsel: ULPI DDR Select (DDRSel)
* Software should set this bit to 0x0.
* @physel: USB 2.0 High-Speed PHY or USB 1.1 Full-Speed Serial
* Software should set this bit to 0x0.
* @fsintf: Full-Speed Serial Interface Select (FSIntf)
* Software should set this bit to 0x0.
* @ulpi_utmi_sel: ULPI or UTMI+ Select (ULPI_UTMI_Sel)
* This bit is always 0x0.
* @phyif: PHY Interface (PHYIf)
* This bit is always 0x1.
* @toutcal: HS/FS Timeout Calibration (TOutCal)
* The number of PHY clocks that the application programs in this
* field is added to the high-speed/full-speed interpacket timeout
* duration in the core to account for any additional delays
* introduced by the PHY. This may be required, since the delay
* introduced by the PHY in generating the linestate condition may
* vary from one PHY to another.
* The USB standard timeout value for high-speed operation is
* 736 to 816 (inclusive) bit times. The USB standard timeout
* value for full-speed operation is 16 to 18 (inclusive) bit
* times. The application must program this field based on the
* speed of enumeration. The number of bit times added per PHY
* clock are:
* High-speed operation:
* * One 30-MHz PHY clock = 16 bit times
* * One 60-MHz PHY clock = 8 bit times
* Full-speed operation:
* * One 30-MHz PHY clock = 0.4 bit times
* * One 60-MHz PHY clock = 0.2 bit times
* * One 48-MHz PHY clock = 0.25 bit times
*/
struct cvmx_usbcx_gusbcfg_s {
__BITFIELD_FIELD(u32 reserved_17_31 : 15,
__BITFIELD_FIELD(u32 otgi2csel : 1,
__BITFIELD_FIELD(u32 phylpwrclksel : 1,
__BITFIELD_FIELD(u32 reserved_14_14 : 1,
__BITFIELD_FIELD(u32 usbtrdtim : 4,
__BITFIELD_FIELD(u32 hnpcap : 1,
__BITFIELD_FIELD(u32 srpcap : 1,
__BITFIELD_FIELD(u32 ddrsel : 1,
__BITFIELD_FIELD(u32 physel : 1,
__BITFIELD_FIELD(u32 fsintf : 1,
__BITFIELD_FIELD(u32 ulpi_utmi_sel : 1,
__BITFIELD_FIELD(u32 phyif : 1,
__BITFIELD_FIELD(u32 toutcal : 3,
;)))))))))))))
} s;
};
/**
* cvmx_usbc#_haint
*
* Host All Channels Interrupt Register (HAINT)
*
* When a significant event occurs on a channel, the Host All Channels Interrupt
* register interrupts the application using the Host Channels Interrupt bit of
* the Core Interrupt register (GINTSTS.HChInt). This is shown in Interrupt.
* There is one interrupt bit per channel, up to a maximum of 16 bits. Bits in
* this register are set and cleared when the application sets and clears bits
* in the corresponding Host Channel-n Interrupt register.
*/
union cvmx_usbcx_haint {
u32 u32;
/**
* struct cvmx_usbcx_haint_s
* @haint: Channel Interrupts (HAINT)
* One bit per channel: Bit 0 for Channel 0, bit 15 for Channel 15
*/
struct cvmx_usbcx_haint_s {
__BITFIELD_FIELD(u32 reserved_16_31 : 16,
__BITFIELD_FIELD(u32 haint : 16,
;))
} s;
};
/**
* cvmx_usbc#_haintmsk
*
* Host All Channels Interrupt Mask Register (HAINTMSK)
*
* The Host All Channel Interrupt Mask register works with the Host All Channel
* Interrupt register to interrupt the application when an event occurs on a
* channel. There is one interrupt mask bit per channel, up to a maximum of 16
* bits.
* Mask interrupt: 1'b0 Unmask interrupt: 1'b1
*/
union cvmx_usbcx_haintmsk {
u32 u32;
/**
* struct cvmx_usbcx_haintmsk_s
* @haintmsk: Channel Interrupt Mask (HAINTMsk)
* One bit per channel: Bit 0 for channel 0, bit 15 for channel 15
*/
struct cvmx_usbcx_haintmsk_s {
__BITFIELD_FIELD(u32 reserved_16_31 : 16,
__BITFIELD_FIELD(u32 haintmsk : 16,
;))
} s;
};
/**
* cvmx_usbc#_hcchar#
*
* Host Channel-n Characteristics Register (HCCHAR)
*
*/
union cvmx_usbcx_hccharx {
u32 u32;
/**
* struct cvmx_usbcx_hccharx_s
* @chena: Channel Enable (ChEna)
* This field is set by the application and cleared by the OTG
* host.
* * 1'b0: Channel disabled
* * 1'b1: Channel enabled
* @chdis: Channel Disable (ChDis)
* The application sets this bit to stop transmitting/receiving
* data on a channel, even before the transfer for that channel is
* complete. The application must wait for the Channel Disabled
* interrupt before treating the channel as disabled.
* @oddfrm: Odd Frame (OddFrm)
* This field is set (reset) by the application to indicate that
* the OTG host must perform a transfer in an odd (micro)frame.
* This field is applicable for only periodic (isochronous and
* interrupt) transactions.
* * 1'b0: Even (micro)frame
* * 1'b1: Odd (micro)frame
* @devaddr: Device Address (DevAddr)
* This field selects the specific device serving as the data
* source or sink.
* @ec: Multi Count (MC) / Error Count (EC)
* When the Split Enable bit of the Host Channel-n Split Control
* register (HCSPLTn.SpltEna) is reset (1'b0), this field indicates
* to the host the number of transactions that should be executed
* per microframe for this endpoint.
* * 2'b00: Reserved. This field yields undefined results.
* * 2'b01: 1 transaction
* * 2'b10: 2 transactions to be issued for this endpoint per
* microframe
* * 2'b11: 3 transactions to be issued for this endpoint per
* microframe
* When HCSPLTn.SpltEna is set (1'b1), this field indicates the
* number of immediate retries to be performed for a periodic split
* transactions on transaction errors. This field must be set to at
* least 2'b01.
* @eptype: Endpoint Type (EPType)
* Indicates the transfer type selected.
* * 2'b00: Control
* * 2'b01: Isochronous
* * 2'b10: Bulk
* * 2'b11: Interrupt
* @lspddev: Low-Speed Device (LSpdDev)
* This field is set by the application to indicate that this
* channel is communicating to a low-speed device.
* @epdir: Endpoint Direction (EPDir)
* Indicates whether the transaction is IN or OUT.
* * 1'b0: OUT
* * 1'b1: IN
* @epnum: Endpoint Number (EPNum)
* Indicates the endpoint number on the device serving as the
* data source or sink.
* @mps: Maximum Packet Size (MPS)
* Indicates the maximum packet size of the associated endpoint.
*/
struct cvmx_usbcx_hccharx_s {
__BITFIELD_FIELD(u32 chena : 1,
__BITFIELD_FIELD(u32 chdis : 1,
__BITFIELD_FIELD(u32 oddfrm : 1,
__BITFIELD_FIELD(u32 devaddr : 7,
__BITFIELD_FIELD(u32 ec : 2,
__BITFIELD_FIELD(u32 eptype : 2,
__BITFIELD_FIELD(u32 lspddev : 1,
__BITFIELD_FIELD(u32 reserved_16_16 : 1,
__BITFIELD_FIELD(u32 epdir : 1,
__BITFIELD_FIELD(u32 epnum : 4,
__BITFIELD_FIELD(u32 mps : 11,
;)))))))))))
} s;
};
/**
* cvmx_usbc#_hcfg
*
* Host Configuration Register (HCFG)
*
* This register configures the core after power-on. Do not make changes to this
* register after initializing the host.
*/
union cvmx_usbcx_hcfg {
u32 u32;
/**
* struct cvmx_usbcx_hcfg_s
* @fslssupp: FS- and LS-Only Support (FSLSSupp)
* The application uses this bit to control the core's enumeration
* speed. Using this bit, the application can make the core
* enumerate as a FS host, even if the connected device supports
* HS traffic. Do not make changes to this field after initial
* programming.
* * 1'b0: HS/FS/LS, based on the maximum speed supported by
* the connected device
* * 1'b1: FS/LS-only, even if the connected device can support HS
* @fslspclksel: FS/LS PHY Clock Select (FSLSPclkSel)
* When the core is in FS Host mode
* * 2'b00: PHY clock is running at 30/60 MHz
* * 2'b01: PHY clock is running at 48 MHz
* * Others: Reserved
* When the core is in LS Host mode
* * 2'b00: PHY clock is running at 30/60 MHz. When the
* UTMI+/ULPI PHY Low Power mode is not selected, use
* 30/60 MHz.
* * 2'b01: PHY clock is running at 48 MHz. When the UTMI+
* PHY Low Power mode is selected, use 48MHz if the PHY
* supplies a 48 MHz clock during LS mode.
* * 2'b10: PHY clock is running at 6 MHz. In USB 1.1 FS mode,
* use 6 MHz when the UTMI+ PHY Low Power mode is
* selected and the PHY supplies a 6 MHz clock during LS
* mode. If you select a 6 MHz clock during LS mode, you must
* do a soft reset.
* * 2'b11: Reserved
*/
struct cvmx_usbcx_hcfg_s {
__BITFIELD_FIELD(u32 reserved_3_31 : 29,
__BITFIELD_FIELD(u32 fslssupp : 1,
__BITFIELD_FIELD(u32 fslspclksel : 2,
;)))
} s;
};
/**
* cvmx_usbc#_hcint#
*
* Host Channel-n Interrupt Register (HCINT)
*
* This register indicates the status of a channel with respect to USB- and
* AHB-related events. The application must read this register when the Host
* Channels Interrupt bit of the Core Interrupt register (GINTSTS.HChInt) is
* set. Before the application can read this register, it must first read
* the Host All Channels Interrupt (HAINT) register to get the exact channel
* number for the Host Channel-n Interrupt register. The application must clear
* the appropriate bit in this register to clear the corresponding bits in the
* HAINT and GINTSTS registers.
*/
union cvmx_usbcx_hcintx {
u32 u32;
/**
* struct cvmx_usbcx_hcintx_s
* @datatglerr: Data Toggle Error (DataTglErr)
* @frmovrun: Frame Overrun (FrmOvrun)
* @bblerr: Babble Error (BblErr)
* @xacterr: Transaction Error (XactErr)
* @nyet: NYET Response Received Interrupt (NYET)
* @ack: ACK Response Received Interrupt (ACK)
* @nak: NAK Response Received Interrupt (NAK)
* @stall: STALL Response Received Interrupt (STALL)
* @ahberr: This bit is always 0x0.
* @chhltd: Channel Halted (ChHltd)
* Indicates the transfer completed abnormally either because of
* any USB transaction error or in response to disable request by
* the application.
* @xfercompl: Transfer Completed (XferCompl)
* Transfer completed normally without any errors.
*/
struct cvmx_usbcx_hcintx_s {
__BITFIELD_FIELD(u32 reserved_11_31 : 21,
__BITFIELD_FIELD(u32 datatglerr : 1,
__BITFIELD_FIELD(u32 frmovrun : 1,
__BITFIELD_FIELD(u32 bblerr : 1,
__BITFIELD_FIELD(u32 xacterr : 1,
__BITFIELD_FIELD(u32 nyet : 1,
__BITFIELD_FIELD(u32 ack : 1,
__BITFIELD_FIELD(u32 nak : 1,
__BITFIELD_FIELD(u32 stall : 1,
__BITFIELD_FIELD(u32 ahberr : 1,
__BITFIELD_FIELD(u32 chhltd : 1,
__BITFIELD_FIELD(u32 xfercompl : 1,
;))))))))))))
} s;
};
/**
* cvmx_usbc#_hcintmsk#
*
* Host Channel-n Interrupt Mask Register (HCINTMSKn)
*
* This register reflects the mask for each channel status described in the
* previous section.
* Mask interrupt: 1'b0 Unmask interrupt: 1'b1
*/
union cvmx_usbcx_hcintmskx {
u32 u32;
/**
* struct cvmx_usbcx_hcintmskx_s
* @datatglerrmsk: Data Toggle Error Mask (DataTglErrMsk)
* @frmovrunmsk: Frame Overrun Mask (FrmOvrunMsk)
* @bblerrmsk: Babble Error Mask (BblErrMsk)
* @xacterrmsk: Transaction Error Mask (XactErrMsk)
* @nyetmsk: NYET Response Received Interrupt Mask (NyetMsk)
* @ackmsk: ACK Response Received Interrupt Mask (AckMsk)
* @nakmsk: NAK Response Received Interrupt Mask (NakMsk)
* @stallmsk: STALL Response Received Interrupt Mask (StallMsk)
* @ahberrmsk: AHB Error Mask (AHBErrMsk)
* @chhltdmsk: Channel Halted Mask (ChHltdMsk)
* @xfercomplmsk: Transfer Completed Mask (XferComplMsk)
*/
struct cvmx_usbcx_hcintmskx_s {
__BITFIELD_FIELD(u32 reserved_11_31 : 21,
__BITFIELD_FIELD(u32 datatglerrmsk : 1,
__BITFIELD_FIELD(u32 frmovrunmsk : 1,
__BITFIELD_FIELD(u32 bblerrmsk : 1,
__BITFIELD_FIELD(u32 xacterrmsk : 1,
__BITFIELD_FIELD(u32 nyetmsk : 1,
__BITFIELD_FIELD(u32 ackmsk : 1,
__BITFIELD_FIELD(u32 nakmsk : 1,
__BITFIELD_FIELD(u32 stallmsk : 1,
__BITFIELD_FIELD(u32 ahberrmsk : 1,
__BITFIELD_FIELD(u32 chhltdmsk : 1,
__BITFIELD_FIELD(u32 xfercomplmsk : 1,
;))))))))))))
} s;
};
/**
* cvmx_usbc#_hcsplt#
*
* Host Channel-n Split Control Register (HCSPLT)
*
*/
union cvmx_usbcx_hcspltx {
u32 u32;
/**
* struct cvmx_usbcx_hcspltx_s
* @spltena: Split Enable (SpltEna)
* The application sets this field to indicate that this channel is
* enabled to perform split transactions.
* @compsplt: Do Complete Split (CompSplt)
* The application sets this field to request the OTG host to
* perform a complete split transaction.
* @xactpos: Transaction Position (XactPos)
* This field is used to determine whether to send all, first,
* middle, or last payloads with each OUT transaction.
* * 2'b11: All. This is the entire data payload is of this
* transaction (which is less than or equal to 188 bytes).
* * 2'b10: Begin. This is the first data payload of this
* transaction (which is larger than 188 bytes).
* * 2'b00: Mid. This is the middle payload of this transaction
* (which is larger than 188 bytes).
* * 2'b01: End. This is the last payload of this transaction
* (which is larger than 188 bytes).
* @hubaddr: Hub Address (HubAddr)
* This field holds the device address of the transaction
* translator's hub.
* @prtaddr: Port Address (PrtAddr)
* This field is the port number of the recipient transaction
* translator.
*/
struct cvmx_usbcx_hcspltx_s {
__BITFIELD_FIELD(u32 spltena : 1,
__BITFIELD_FIELD(u32 reserved_17_30 : 14,
__BITFIELD_FIELD(u32 compsplt : 1,
__BITFIELD_FIELD(u32 xactpos : 2,
__BITFIELD_FIELD(u32 hubaddr : 7,
__BITFIELD_FIELD(u32 prtaddr : 7,
;))))))
} s;
};
/**
* cvmx_usbc#_hctsiz#
*
* Host Channel-n Transfer Size Register (HCTSIZ)
*
*/
union cvmx_usbcx_hctsizx {
u32 u32;
/**
* struct cvmx_usbcx_hctsizx_s
* @dopng: Do Ping (DoPng)
* Setting this field to 1 directs the host to do PING protocol.
* @pid: PID (Pid)
* The application programs this field with the type of PID to use
* for the initial transaction. The host will maintain this field
* for the rest of the transfer.
* * 2'b00: DATA0
* * 2'b01: DATA2
* * 2'b10: DATA1
* * 2'b11: MDATA (non-control)/SETUP (control)
* @pktcnt: Packet Count (PktCnt)
* This field is programmed by the application with the expected
* number of packets to be transmitted (OUT) or received (IN).
* The host decrements this count on every successful
* transmission or reception of an OUT/IN packet. Once this count
* reaches zero, the application is interrupted to indicate normal
* completion.
* @xfersize: Transfer Size (XferSize)
* For an OUT, this field is the number of data bytes the host will
* send during the transfer.
* For an IN, this field is the buffer size that the application
* has reserved for the transfer. The application is expected to
* program this field as an integer multiple of the maximum packet
* size for IN transactions (periodic and non-periodic).
*/
struct cvmx_usbcx_hctsizx_s {
__BITFIELD_FIELD(u32 dopng : 1,
__BITFIELD_FIELD(u32 pid : 2,
__BITFIELD_FIELD(u32 pktcnt : 10,
__BITFIELD_FIELD(u32 xfersize : 19,
;))))
} s;
};
/**
* cvmx_usbc#_hfir
*
* Host Frame Interval Register (HFIR)
*
* This register stores the frame interval information for the current speed to
* which the O2P USB core has enumerated.
*/
union cvmx_usbcx_hfir {
u32 u32;
/**
* struct cvmx_usbcx_hfir_s
* @frint: Frame Interval (FrInt)
* The value that the application programs to this field specifies
* the interval between two consecutive SOFs (FS) or micro-
* SOFs (HS) or Keep-Alive tokens (HS). This field contains the
* number of PHY clocks that constitute the required frame
* interval. The default value set in this field for a FS operation
* when the PHY clock frequency is 60 MHz. The application can
* write a value to this register only after the Port Enable bit of
* the Host Port Control and Status register (HPRT.PrtEnaPort)
* has been set. If no value is programmed, the core calculates
* the value based on the PHY clock specified in the FS/LS PHY
* Clock Select field of the Host Configuration register
* (HCFG.FSLSPclkSel). Do not change the value of this field
* after the initial configuration.
* * 125 us (PHY clock frequency for HS)
* * 1 ms (PHY clock frequency for FS/LS)
*/
struct cvmx_usbcx_hfir_s {
__BITFIELD_FIELD(u32 reserved_16_31 : 16,
__BITFIELD_FIELD(u32 frint : 16,
;))
} s;
};
/**
* cvmx_usbc#_hfnum
*
* Host Frame Number/Frame Time Remaining Register (HFNUM)
*
* This register indicates the current frame number.
* It also indicates the time remaining (in terms of the number of PHY clocks)
* in the current (micro)frame.
*/
union cvmx_usbcx_hfnum {
u32 u32;
/**
* struct cvmx_usbcx_hfnum_s
* @frrem: Frame Time Remaining (FrRem)
* Indicates the amount of time remaining in the current
* microframe (HS) or frame (FS/LS), in terms of PHY clocks.
* This field decrements on each PHY clock. When it reaches
* zero, this field is reloaded with the value in the Frame
* Interval register and a new SOF is transmitted on the USB.
* @frnum: Frame Number (FrNum)
* This field increments when a new SOF is transmitted on the
* USB, and is reset to 0 when it reaches 16'h3FFF.
*/
struct cvmx_usbcx_hfnum_s {
__BITFIELD_FIELD(u32 frrem : 16,
__BITFIELD_FIELD(u32 frnum : 16,
;))
} s;
};
/**
* cvmx_usbc#_hprt
*
* Host Port Control and Status Register (HPRT)
*
* This register is available in both Host and Device modes.
* Currently, the OTG Host supports only one port.
* A single register holds USB port-related information such as USB reset,
* enable, suspend, resume, connect status, and test mode for each port. The
* R_SS_WC bits in this register can trigger an interrupt to the application
* through the Host Port Interrupt bit of the Core Interrupt register
* (GINTSTS.PrtInt). On a Port Interrupt, the application must read this
* register and clear the bit that caused the interrupt. For the R_SS_WC bits,
* the application must write a 1 to the bit to clear the interrupt.
*/
union cvmx_usbcx_hprt {
u32 u32;
/**
* struct cvmx_usbcx_hprt_s
* @prtspd: Port Speed (PrtSpd)
* Indicates the speed of the device attached to this port.
* * 2'b00: High speed
* * 2'b01: Full speed
* * 2'b10: Low speed
* * 2'b11: Reserved
* @prttstctl: Port Test Control (PrtTstCtl)
* The application writes a nonzero value to this field to put
* the port into a Test mode, and the corresponding pattern is
* signaled on the port.
* * 4'b0000: Test mode disabled
* * 4'b0001: Test_J mode
* * 4'b0010: Test_K mode
* * 4'b0011: Test_SE0_NAK mode
* * 4'b0100: Test_Packet mode
* * 4'b0101: Test_Force_Enable
* * Others: Reserved
* PrtSpd must be zero (i.e. the interface must be in high-speed
* mode) to use the PrtTstCtl test modes.
* @prtpwr: Port Power (PrtPwr)
* The application uses this field to control power to this port,
* and the core clears this bit on an overcurrent condition.
* * 1'b0: Power off
* * 1'b1: Power on
* @prtlnsts: Port Line Status (PrtLnSts)
* Indicates the current logic level USB data lines
* * Bit [10]: Logic level of D-
* * Bit [11]: Logic level of D+
* @prtrst: Port Reset (PrtRst)
* When the application sets this bit, a reset sequence is
* started on this port. The application must time the reset
* period and clear this bit after the reset sequence is
* complete.
* * 1'b0: Port not in reset
* * 1'b1: Port in reset
* The application must leave this bit set for at least a
* minimum duration mentioned below to start a reset on the
* port. The application can leave it set for another 10 ms in
* addition to the required minimum duration, before clearing
* the bit, even though there is no maximum limit set by the
* USB standard.
* * High speed: 50 ms
* * Full speed/Low speed: 10 ms
* @prtsusp: Port Suspend (PrtSusp)
* The application sets this bit to put this port in Suspend
* mode. The core only stops sending SOFs when this is set.
* To stop the PHY clock, the application must set the Port
* Clock Stop bit, which will assert the suspend input pin of
* the PHY.
* The read value of this bit reflects the current suspend
* status of the port. This bit is cleared by the core after a
* remote wakeup signal is detected or the application sets
* the Port Reset bit or Port Resume bit in this register or the
* Resume/Remote Wakeup Detected Interrupt bit or
* Disconnect Detected Interrupt bit in the Core Interrupt
* register (GINTSTS.WkUpInt or GINTSTS.DisconnInt,
* respectively).
* * 1'b0: Port not in Suspend mode
* * 1'b1: Port in Suspend mode
* @prtres: Port Resume (PrtRes)
* The application sets this bit to drive resume signaling on
* the port. The core continues to drive the resume signal
* until the application clears this bit.
* If the core detects a USB remote wakeup sequence, as
* indicated by the Port Resume/Remote Wakeup Detected
* Interrupt bit of the Core Interrupt register
* (GINTSTS.WkUpInt), the core starts driving resume
* signaling without application intervention and clears this bit
* when it detects a disconnect condition. The read value of
* this bit indicates whether the core is currently driving
* resume signaling.
* * 1'b0: No resume driven
* * 1'b1: Resume driven
* @prtovrcurrchng: Port Overcurrent Change (PrtOvrCurrChng)
* The core sets this bit when the status of the Port
* Overcurrent Active bit (bit 4) in this register changes.
* @prtovrcurract: Port Overcurrent Active (PrtOvrCurrAct)
* Indicates the overcurrent condition of the port.
* * 1'b0: No overcurrent condition
* * 1'b1: Overcurrent condition
* @prtenchng: Port Enable/Disable Change (PrtEnChng)
* The core sets this bit when the status of the Port Enable bit
* [2] of this register changes.
* @prtena: Port Enable (PrtEna)
* A port is enabled only by the core after a reset sequence,
* and is disabled by an overcurrent condition, a disconnect
* condition, or by the application clearing this bit. The
* application cannot set this bit by a register write. It can only
* clear it to disable the port. This bit does not trigger any
* interrupt to the application.
* * 1'b0: Port disabled
* * 1'b1: Port enabled
* @prtconndet: Port Connect Detected (PrtConnDet)
* The core sets this bit when a device connection is detected
* to trigger an interrupt to the application using the Host Port
* Interrupt bit of the Core Interrupt register (GINTSTS.PrtInt).
* The application must write a 1 to this bit to clear the
* interrupt.
* @prtconnsts: Port Connect Status (PrtConnSts)
* * 0: No device is attached to the port.
* * 1: A device is attached to the port.
*/
struct cvmx_usbcx_hprt_s {
__BITFIELD_FIELD(u32 reserved_19_31 : 13,
__BITFIELD_FIELD(u32 prtspd : 2,
__BITFIELD_FIELD(u32 prttstctl : 4,
__BITFIELD_FIELD(u32 prtpwr : 1,
__BITFIELD_FIELD(u32 prtlnsts : 2,
__BITFIELD_FIELD(u32 reserved_9_9 : 1,
__BITFIELD_FIELD(u32 prtrst : 1,
__BITFIELD_FIELD(u32 prtsusp : 1,
__BITFIELD_FIELD(u32 prtres : 1,
__BITFIELD_FIELD(u32 prtovrcurrchng : 1,
__BITFIELD_FIELD(u32 prtovrcurract : 1,
__BITFIELD_FIELD(u32 prtenchng : 1,
__BITFIELD_FIELD(u32 prtena : 1,
__BITFIELD_FIELD(u32 prtconndet : 1,
__BITFIELD_FIELD(u32 prtconnsts : 1,
;)))))))))))))))
} s;
};
/**
* cvmx_usbc#_hptxfsiz
*
* Host Periodic Transmit FIFO Size Register (HPTXFSIZ)
*
* This register holds the size and the memory start address of the Periodic
* TxFIFO, as shown in Figures 310 and 311.
*/
union cvmx_usbcx_hptxfsiz {
u32 u32;
/**
* struct cvmx_usbcx_hptxfsiz_s
* @ptxfsize: Host Periodic TxFIFO Depth (PTxFSize)
* This value is in terms of 32-bit words.
* * Minimum value is 16
* * Maximum value is 32768
* @ptxfstaddr: Host Periodic TxFIFO Start Address (PTxFStAddr)
*/
struct cvmx_usbcx_hptxfsiz_s {
__BITFIELD_FIELD(u32 ptxfsize : 16,
__BITFIELD_FIELD(u32 ptxfstaddr : 16,
;))
} s;
};
/**
* cvmx_usbc#_hptxsts
*
* Host Periodic Transmit FIFO/Queue Status Register (HPTXSTS)
*
* This read-only register contains the free space information for the Periodic
* TxFIFO and the Periodic Transmit Request Queue
*/
union cvmx_usbcx_hptxsts {
u32 u32;
/**
* struct cvmx_usbcx_hptxsts_s
* @ptxqtop: Top of the Periodic Transmit Request Queue (PTxQTop)
* This indicates the entry in the Periodic Tx Request Queue that
* is currently being processes by the MAC.
* This register is used for debugging.
* * Bit [31]: Odd/Even (micro)frame
* - 1'b0: send in even (micro)frame
* - 1'b1: send in odd (micro)frame
* * Bits [30:27]: Channel/endpoint number
* * Bits [26:25]: Type
* - 2'b00: IN/OUT
* - 2'b01: Zero-length packet
* - 2'b10: CSPLIT
* - 2'b11: Disable channel command
* * Bit [24]: Terminate (last entry for the selected
* channel/endpoint)
* @ptxqspcavail: Periodic Transmit Request Queue Space Available
* (PTxQSpcAvail)
* Indicates the number of free locations available to be written
* in the Periodic Transmit Request Queue. This queue holds both
* IN and OUT requests.
* * 8'h0: Periodic Transmit Request Queue is full
* * 8'h1: 1 location available
* * 8'h2: 2 locations available
* * n: n locations available (0..8)
* * Others: Reserved
* @ptxfspcavail: Periodic Transmit Data FIFO Space Available
* (PTxFSpcAvail)
* Indicates the number of free locations available to be written
* to in the Periodic TxFIFO.
* Values are in terms of 32-bit words
* * 16'h0: Periodic TxFIFO is full
* * 16'h1: 1 word available
* * 16'h2: 2 words available
* * 16'hn: n words available (where 0..32768)
* * 16'h8000: 32768 words available
* * Others: Reserved
*/
struct cvmx_usbcx_hptxsts_s {
__BITFIELD_FIELD(u32 ptxqtop : 8,
__BITFIELD_FIELD(u32 ptxqspcavail : 8,
__BITFIELD_FIELD(u32 ptxfspcavail : 16,
;)))
} s;
};
/**
* cvmx_usbn#_clk_ctl
*
* USBN_CLK_CTL = USBN's Clock Control
*
* This register is used to control the frequency of the hclk and the
* hreset and phy_rst signals.
*/
union cvmx_usbnx_clk_ctl {
u64 u64;
/**
* struct cvmx_usbnx_clk_ctl_s
* @divide2: The 'hclk' used by the USB subsystem is derived
* from the eclk.
* Also see the field DIVIDE. DIVIDE2<1> must currently
* be zero because it is not implemented, so the maximum
* ratio of eclk/hclk is currently 16.
* The actual divide number for hclk is:
* (DIVIDE2 + 1) * (DIVIDE + 1)
* @hclk_rst: When this field is '0' the HCLK-DIVIDER used to
* generate the hclk in the USB Subsystem is held
* in reset. This bit must be set to '0' before
* changing the value os DIVIDE in this register.
* The reset to the HCLK_DIVIDERis also asserted
* when core reset is asserted.
* @p_x_on: Force USB-PHY on during suspend.
* '1' USB-PHY XO block is powered-down during
* suspend.
* '0' USB-PHY XO block is powered-up during
* suspend.
* The value of this field must be set while POR is
* active.
* @p_rtype: PHY reference clock type
* On CN50XX/CN52XX/CN56XX the values are:
* '0' The USB-PHY uses a 12MHz crystal as a clock source
* at the USB_XO and USB_XI pins.
* '1' Reserved.
* '2' The USB_PHY uses 12/24/48MHz 2.5V board clock at the
* USB_XO pin. USB_XI should be tied to ground in this
* case.
* '3' Reserved.
* On CN3xxx bits 14 and 15 are p_xenbn and p_rclk and values are:
* '0' Reserved.
* '1' Reserved.
* '2' The PHY PLL uses the XO block output as a reference.
* The XO block uses an external clock supplied on the
* XO pin. USB_XI should be tied to ground for this
* usage.
* '3' The XO block uses the clock from a crystal.
* @p_com_on: '0' Force USB-PHY XO Bias, Bandgap and PLL to
* remain powered in Suspend Mode.
* '1' The USB-PHY XO Bias, Bandgap and PLL are
* powered down in suspend mode.
* The value of this field must be set while POR is
* active.
* @p_c_sel: Phy clock speed select.
* Selects the reference clock / crystal frequency.
* '11': Reserved
* '10': 48 MHz (reserved when a crystal is used)
* '01': 24 MHz (reserved when a crystal is used)
* '00': 12 MHz
* The value of this field must be set while POR is
* active.
* NOTE: if a crystal is used as a reference clock,
* this field must be set to 12 MHz.
* @cdiv_byp: Used to enable the bypass input to the USB_CLK_DIV.
* @sd_mode: Scaledown mode for the USBC. Control timing events
* in the USBC, for normal operation this must be '0'.
* @s_bist: Starts bist on the hclk memories, during the '0'
* to '1' transition.
* @por: Power On Reset for the PHY.
* Resets all the PHYS registers and state machines.
* @enable: When '1' allows the generation of the hclk. When
* '0' the hclk will not be generated. SEE DIVIDE
* field of this register.
* @prst: When this field is '0' the reset associated with
* the phy_clk functionality in the USB Subsystem is
* help in reset. This bit should not be set to '1'
* until the time it takes 6 clocks (hclk or phy_clk,
* whichever is slower) has passed. Under normal
* operation once this bit is set to '1' it should not
* be set to '0'.
* @hrst: When this field is '0' the reset associated with
* the hclk functioanlity in the USB Subsystem is
* held in reset.This bit should not be set to '1'
* until 12ms after phy_clk is stable. Under normal
* operation, once this bit is set to '1' it should
* not be set to '0'.
* @divide: The frequency of 'hclk' used by the USB subsystem
* is the eclk frequency divided by the value of
* (DIVIDE2 + 1) * (DIVIDE + 1), also see the field
* DIVIDE2 of this register.
* The hclk frequency should be less than 125Mhz.
* After writing a value to this field the SW should
* read the field for the value written.
* The ENABLE field of this register should not be set
* until AFTER this field is set and then read.
*/
struct cvmx_usbnx_clk_ctl_s {
__BITFIELD_FIELD(u64 reserved_20_63 : 44,
__BITFIELD_FIELD(u64 divide2 : 2,
__BITFIELD_FIELD(u64 hclk_rst : 1,
__BITFIELD_FIELD(u64 p_x_on : 1,
__BITFIELD_FIELD(u64 p_rtype : 2,
__BITFIELD_FIELD(u64 p_com_on : 1,
__BITFIELD_FIELD(u64 p_c_sel : 2,
__BITFIELD_FIELD(u64 cdiv_byp : 1,
__BITFIELD_FIELD(u64 sd_mode : 2,
__BITFIELD_FIELD(u64 s_bist : 1,
__BITFIELD_FIELD(u64 por : 1,
__BITFIELD_FIELD(u64 enable : 1,
__BITFIELD_FIELD(u64 prst : 1,
__BITFIELD_FIELD(u64 hrst : 1,
__BITFIELD_FIELD(u64 divide : 3,
;)))))))))))))))
} s;
};
/**
* cvmx_usbn#_usbp_ctl_status
*
* USBN_USBP_CTL_STATUS = USBP Control And Status Register
*
* Contains general control and status information for the USBN block.
*/
union cvmx_usbnx_usbp_ctl_status {
u64 u64;
/**
* struct cvmx_usbnx_usbp_ctl_status_s
* @txrisetune: HS Transmitter Rise/Fall Time Adjustment
* @txvreftune: HS DC Voltage Level Adjustment
* @txfslstune: FS/LS Source Impedance Adjustment
* @txhsxvtune: Transmitter High-Speed Crossover Adjustment
* @sqrxtune: Squelch Threshold Adjustment
* @compdistune: Disconnect Threshold Adjustment
* @otgtune: VBUS Valid Threshold Adjustment
* @otgdisable: OTG Block Disable
* @portreset: Per_Port Reset
* @drvvbus: Drive VBUS
* @lsbist: Low-Speed BIST Enable.
* @fsbist: Full-Speed BIST Enable.
* @hsbist: High-Speed BIST Enable.
* @bist_done: PHY Bist Done.
* Asserted at the end of the PHY BIST sequence.
* @bist_err: PHY Bist Error.
* Indicates an internal error was detected during
* the BIST sequence.
* @tdata_out: PHY Test Data Out.
* Presents either internally generated signals or
* test register contents, based upon the value of
* test_data_out_sel.
* @siddq: Drives the USBP (USB-PHY) SIDDQ input.
* Normally should be set to zero.
* When customers have no intent to use USB PHY
* interface, they should:
* - still provide 3.3V to USB_VDD33, and
* - tie USB_REXT to 3.3V supply, and
* - set USBN*_USBP_CTL_STATUS[SIDDQ]=1
* @txpreemphasistune: HS Transmitter Pre-Emphasis Enable
* @dma_bmode: When set to 1 the L2C DMA address will be updated
* with byte-counts between packets. When set to 0
* the L2C DMA address is incremented to the next
* 4-byte aligned address after adding byte-count.
* @usbc_end: Bigendian input to the USB Core. This should be
* set to '0' for operation.
* @usbp_bist: PHY, This is cleared '0' to run BIST on the USBP.
* @tclk: PHY Test Clock, used to load TDATA_IN to the USBP.
* @dp_pulld: PHY DP_PULLDOWN input to the USB-PHY.
* This signal enables the pull-down resistance on
* the D+ line. '1' pull down-resistance is connected
* to D+/ '0' pull down resistance is not connected
* to D+. When an A/B device is acting as a host
* (downstream-facing port), dp_pulldown and
* dm_pulldown are enabled. This must not toggle
* during normal operation.
* @dm_pulld: PHY DM_PULLDOWN input to the USB-PHY.
* This signal enables the pull-down resistance on
* the D- line. '1' pull down-resistance is connected
* to D-. '0' pull down resistance is not connected
* to D-. When an A/B device is acting as a host
* (downstream-facing port), dp_pulldown and
* dm_pulldown are enabled. This must not toggle
* during normal operation.
* @hst_mode: When '0' the USB is acting as HOST, when '1'
* USB is acting as device. This field needs to be
* set while the USB is in reset.
* @tuning: Transmitter Tuning for High-Speed Operation.
* Tunes the current supply and rise/fall output
* times for high-speed operation.
* [20:19] == 11: Current supply increased
* approximately 9%
* [20:19] == 10: Current supply increased
* approximately 4.5%
* [20:19] == 01: Design default.
* [20:19] == 00: Current supply decreased
* approximately 4.5%
* [22:21] == 11: Rise and fall times are increased.
* [22:21] == 10: Design default.
* [22:21] == 01: Rise and fall times are decreased.
* [22:21] == 00: Rise and fall times are decreased
* further as compared to the 01 setting.
* @tx_bs_enh: Transmit Bit Stuffing on [15:8].
* Enables or disables bit stuffing on data[15:8]
* when bit-stuffing is enabled.
* @tx_bs_en: Transmit Bit Stuffing on [7:0].
* Enables or disables bit stuffing on data[7:0]
* when bit-stuffing is enabled.
* @loop_enb: PHY Loopback Test Enable.
* '1': During data transmission the receive is
* enabled.
* '0': During data transmission the receive is
* disabled.
* Must be '0' for normal operation.
* @vtest_enb: Analog Test Pin Enable.
* '1' The PHY's analog_test pin is enabled for the
* input and output of applicable analog test signals.
* '0' THe analog_test pin is disabled.
* @bist_enb: Built-In Self Test Enable.
* Used to activate BIST in the PHY.
* @tdata_sel: Test Data Out Select.
* '1' test_data_out[3:0] (PHY) register contents
* are output. '0' internally generated signals are
* output.
* @taddr_in: Mode Address for Test Interface.
* Specifies the register address for writing to or
* reading from the PHY test interface register.
* @tdata_in: Internal Testing Register Input Data and Select
* This is a test bus. Data is present on [3:0],
* and its corresponding select (enable) is present
* on bits [7:4].
* @ate_reset: Reset input from automatic test equipment.
* This is a test signal. When the USB Core is
* powered up (not in Susned Mode), an automatic
* tester can use this to disable phy_clock and
* free_clk, then re-enable them with an aligned
* phase.
* '1': The phy_clk and free_clk outputs are
* disabled. "0": The phy_clock and free_clk outputs
* are available within a specific period after the
* de-assertion.
*/
struct cvmx_usbnx_usbp_ctl_status_s {
__BITFIELD_FIELD(u64 txrisetune : 1,
__BITFIELD_FIELD(u64 txvreftune : 4,
__BITFIELD_FIELD(u64 txfslstune : 4,
__BITFIELD_FIELD(u64 txhsxvtune : 2,
__BITFIELD_FIELD(u64 sqrxtune : 3,
__BITFIELD_FIELD(u64 compdistune : 3,
__BITFIELD_FIELD(u64 otgtune : 3,
__BITFIELD_FIELD(u64 otgdisable : 1,
__BITFIELD_FIELD(u64 portreset : 1,
__BITFIELD_FIELD(u64 drvvbus : 1,
__BITFIELD_FIELD(u64 lsbist : 1,
__BITFIELD_FIELD(u64 fsbist : 1,
__BITFIELD_FIELD(u64 hsbist : 1,
__BITFIELD_FIELD(u64 bist_done : 1,
__BITFIELD_FIELD(u64 bist_err : 1,
__BITFIELD_FIELD(u64 tdata_out : 4,
__BITFIELD_FIELD(u64 siddq : 1,
__BITFIELD_FIELD(u64 txpreemphasistune : 1,
__BITFIELD_FIELD(u64 dma_bmode : 1,
__BITFIELD_FIELD(u64 usbc_end : 1,
__BITFIELD_FIELD(u64 usbp_bist : 1,
__BITFIELD_FIELD(u64 tclk : 1,
__BITFIELD_FIELD(u64 dp_pulld : 1,
__BITFIELD_FIELD(u64 dm_pulld : 1,
__BITFIELD_FIELD(u64 hst_mode : 1,
__BITFIELD_FIELD(u64 tuning : 4,
__BITFIELD_FIELD(u64 tx_bs_enh : 1,
__BITFIELD_FIELD(u64 tx_bs_en : 1,
__BITFIELD_FIELD(u64 loop_enb : 1,
__BITFIELD_FIELD(u64 vtest_enb : 1,
__BITFIELD_FIELD(u64 bist_enb : 1,
__BITFIELD_FIELD(u64 tdata_sel : 1,
__BITFIELD_FIELD(u64 taddr_in : 4,
__BITFIELD_FIELD(u64 tdata_in : 8,
__BITFIELD_FIELD(u64 ate_reset : 1,
;)))))))))))))))))))))))))))))))))))
} s;
};
#endif /* __OCTEON_HCD_H__ */