Directory Files
.. 6
File Size
.bh.o.cmd 74 kB
.cw1200_core.ko.cmd 359 B
.cw1200_core.mod.cmd 263 B
.cw1200_core.mod.o.cmd 50 kB
.cw1200_core.o.cmd 547 B
.cw1200_sdio.o.cmd 78 kB
.cw1200_spi.o.cmd 78 kB
.cw1200_wlan_sdio.ko.cmd 379 B
.cw1200_wlan_sdio.mod.cmd 214 B
.cw1200_wlan_sdio.mod.o.cmd 50 kB
.cw1200_wlan_sdio.o.cmd 572 B
.cw1200_wlan_spi.ko.cmd 375 B
.cw1200_wlan_spi.mod.cmd 211 B
.cw1200_wlan_spi.mod.o.cmd 50 kB
.cw1200_wlan_spi.o.cmd 567 B
.debug.o.cmd 74 kB
.fwio.o.cmd 74 kB
.hwio.o.cmd 74 kB
.main.o.cmd 75 kB
.modules.order.cmd 279 B
.pm.o.cmd 74 kB
.queue.o.cmd 74 kB
.scan.o.cmd 74 kB
.sta.o.cmd 74 kB
.txrx.o.cmd 74 kB
.wsm.o.cmd 74 kB
Kconfig 981 B
Makefile 434 B
bh.c 15 kB
bh.h 822 B
bh.o 105 kB
cw1200.h 8.3 kB
cw1200_core.ko 1.5 MB
cw1200_core.mod 414 B
cw1200_core.mod.c 700 B
cw1200_core.mod.o 5.6 kB
cw1200_core.o 1.5 MB
cw1200_sdio.c 9.8 kB
cw1200_sdio.o 46 kB
cw1200_spi.c 11 kB
cw1200_spi.o 43 kB
cw1200_wlan_sdio.ko 62 kB
cw1200_wlan_sdio.mod 45 B
cw1200_wlan_sdio.mod.c 509 B
cw1200_wlan_sdio.mod.o 3.4 kB
cw1200_wlan_sdio.o 62 kB
cw1200_wlan_spi.ko 57 kB
cw1200_wlan_spi.mod 44 B
cw1200_wlan_spi.mod.c 464 B
cw1200_wlan_spi.mod.o 3.3 kB
cw1200_wlan_spi.o 57 kB
debug.c 11 kB
debug.h 1.9 kB
debug.o 87 kB
fwio.c 12 kB
fwio.h 1.0 kB
fwio.o 56 kB
hwbus.h 920 B
hwio.c 7.2 kB
hwio.h 7.8 kB
hwio.o 34 kB
main.c 17 kB
main.o 82 kB
modules.order 144 B
pm.c 9.0 kB
pm.h 1.2 kB
pm.o 39 kB
queue.c 14 kB
queue.h 3.2 kB
queue.o 71 kB
scan.c 13 kB
scan.h 1.6 kB
scan.o 54 kB
sta.c 65 kB
sta.h 4.8 kB
sta.o 273 kB
txrx.c 40 kB
txrx.h 3.1 kB
txrx.o 181 kB
wsm.c 44 kB
wsm.h 48 kB
wsm.o 205 kB

Linux v7.4-rc3 - cw1200

# SPDX-License-Identifier: GPL-2.0-only
config CW1200
	tristate "CW1200 WLAN support"
	depends on MAC80211 && CFG80211
	help
	  This is a driver for the ST-E CW1100 & CW1200 WLAN chipsets.
	  This option just enables the driver core, see below for
	  specific bus support.

if CW1200

config CW1200_WLAN_SDIO
	tristate "Support SDIO platforms"
	depends on CW1200 && MMC
	help
	  Enable support for the CW1200 connected via an SDIO bus.
	  By default this driver only supports the Sagrad SG901-1091/1098 EVK
	  and similar designs that utilize a hardware reset circuit. To
	  support different CW1200 SDIO designs you will need to override
	  the default platform data by calling cw1200_sdio_set_platform_data()
	  in your board setup file.

config CW1200_WLAN_SPI
	tristate "Support SPI platforms"
	depends on CW1200 && SPI
	help
	  Enables support for the CW1200 connected via a SPI bus.  You will
	  need to add appropriate platform data glue in your board setup
	  file.

endif