// SPDX-License-Identifier: (GPL-2.0 OR MIT)
/*
 * As a loose attempt to separate RP1 customizations from SoC peripherals
 * definitioni, this file is intended to host the override nodes for the RP1
 * peripherals, e.g. to declare the phy of the ethernet interface or custom
 * pin setup.
 * All other nodes that do not have anything to do with RP1 should be added
 * to the included bcm2712-rpi-5-b-base.dtsi instead.
 */

/dts-v1/;

#include "bcm2712-rpi-5-b-base.dtsi"

/ {
	aliases {
		ethernet0 = &rp1_eth;
	};
};

&pcie2 {
	pci@0,0 {
		reg = <0x0 0x0 0x0 0x0 0x0>;
		ranges;
		bus-range = <0 1>;
		device_type = "pci";
		#address-cells = <3>;
		#size-cells = <2>;

		dev@0,0 {
			compatible = "pci1de4,1";
			reg = <0x10000 0x0 0x0 0x0 0x0>;
			ranges = <0x1 0x0 0x0 0x82010000 0x0 0x0 0x0 0x400000>;
			interrupt-controller;
			#interrupt-cells = <2>;
			#address-cells = <3>;
			#size-cells = <2>;

			#include "rp1-common.dtsi"
		};
	};
};

&rp1_eth {
	assigned-clocks = <&rp1_clocks RP1_CLK_ETH_TSU>,
			  <&rp1_clocks RP1_CLK_ETH>;
	assigned-clock-rates = <50000000>,
			       <125000000>;
	status = "okay";
	phy-mode = "rgmii-id";
	phy-handle = <&phy1>;

	mdio {
		reg = <0x1>;
		reset-gpios = <&rp1_gpio 32 GPIO_ACTIVE_LOW>;
		reset-delay-us = <5000>;
		#address-cells = <1>;
		#size-cells = <0>;

		phy1: ethernet-phy@1 {
			reg = <0x1>;
		};
	};
};

&rp1_gpio {
	fan_pwm_default_state: fan-pwm-default-state {
		function = "pwm1";
		pins = "gpio45";
		bias-pull-down;
	};

	usb_vbus_default_state: usb-vbus-default-state {
		function = "vbus1";
		groups = "vbus1";
	};

	rp1_spi0_default_state: rp1-spi0-default-state {
		function = "spi0";
		groups = "spi0";
		bias-disable;
		drive-strength = <12>;
		slew-rate = <1>;
	};

	rp1_spi0_cs_default_state: rp1-spi0-cs-default-state {
		function = "gpio";
		pins = "gpio7", "gpio8";
		bias-pull-up;
	};

	rp1_i2c4_default_state: rp1-i2c4-default-state {
		function = "i2c4";
		groups = "i2c4_2";
		drive-strength = <12>;
		bias-pull-up;
	};

	rp1_i2c6_default_state: rp1-i2c6-default-state {
		function = "i2c6";
		groups = "i2c6_0";
		drive-strength = <12>;
		bias-pull-up;
	};
};

&rp1_i2c4 {
	pinctrl-0 = <&rp1_i2c4_default_state>;
	pinctrl-names = "default";
};

&rp1_i2c6 {
	pinctrl-0 = <&rp1_i2c6_default_state>;
	pinctrl-names = "default";
};

&rp1_spi0 {
	pinctrl-0 = <&rp1_spi0_default_state &rp1_spi0_cs_default_state>;
	pinctrl-names = "default";

	num-cs = <2>;
	cs-gpios = <&rp1_gpio 8 GPIO_ACTIVE_LOW &rp1_gpio 7 GPIO_ACTIVE_LOW>;
};

&rp1_pwm1 {
	pinctrl-0 = <&fan_pwm_default_state>;
	pinctrl-names = "default";
	status = "okay";
};

&rp1_usb0 {
	pinctrl-0 = <&usb_vbus_default_state>;
	pinctrl-names = "default";
	status = "okay";
};

&rp1_usb1 {
	status = "okay";
};