// SPDX-License-Identifier: (GPL-2.0 OR MIT)
/dts-v1/;
#include "dt-bindings/gpio/gpio.h"
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/input/input.h>
#include "omap443x.dtsi"

/ {
	memory@80000000 {
		device_type = "memory";
		reg = <0x80000000 0x40000000>; /* 1 GB */
	};

	reserved-memory {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;

		continuous_splash: framebuffer@bef00000 {
			reg = <0xbef00000 (1024 * 600 * 4)>;
			no-map;
		};
	};

	chosen {
		stdout-path = &uart3;
		#address-cells = <1>;
	};

	i2c-gpio5 {
		compatible = "i2c-gpio";
		pinctrl-names = "default";
		pinctrl-0 = <&i2c5_pins>;
		sda-gpios = <&gpio4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
		scl-gpios = <&gpio4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
		i2c-gpio,delay-us = <10>;
		#address-cells = <1>;
		#size-cells = <0>;

		/* TODO: SMB136 Charger for 7" variant at 0x4d */
	};

	i2c-gpio6 {
		compatible = "i2c-gpio";
		pinctrl-names = "default";
		pinctrl-0 = <&i2c6_pins>;
		sda-gpios = <&gpio3 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
		scl-gpios = <&gpio3 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
		i2c-gpio,delay-us = <10>;
		#address-cells = <1>;
		#size-cells = <0>;

		/* TODO: STMPE811 ADC at 0x41 */
	};

	i2c-gpio7 {
		compatible = "i2c-gpio";
		pinctrl-names = "default";
		pinctrl-0 = <&i2c7_pins>;
		sda-gpios = <&gpio2 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
		scl-gpios = <&gpio2 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
		i2c-gpio,delay-us = <3>;
		#address-cells = <1>;
		#size-cells = <0>;

		fuel-gauge@36 {
			compatible = "maxim,max17042";
			reg = <0x36>;
			pinctrl-0 = <&fuel_alert_irq>;
			pinctrl-names = "default";
			interrupt-parent = <&gpio2>;
			interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
			maxim,rsns-microohm = <10000>;
			maxim,over-heat-temp = <500>;
			maxim,dead-volt = <2500>;
			maxim,over-volt = <4300>;
		};
	};

	reg_espresso_wlan: regulator-espresso-wlan {
		pinctrl-names = "default";
		pinctrl-0 = <&wlanen_gpio>;
		compatible = "regulator-fixed";
		regulator-name = "espresso_wlan";
		regulator-max-microvolt = <2000000>;
		regulator-min-microvolt = <2000000>;
		gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO_104 */
		startup-delay-us = <70000>;
		regulator-always-on;
		enable-active-high;
	};

	wlan_pwrseq: wlan-pwrseq {
		compatible = "mmc-pwrseq-simple";
		clocks = <&twl 0>;
		clock-names = "ext_clock";
	};

	reg_espresso_internal: regulator-espresso-internal {
		compatible = "regulator-fixed";
		regulator-name = "eMMC_LDO";
		regulator-max-microvolt = <1800000>;
		regulator-min-microvolt = <1800000>;
		gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; /* GPIO_63 */
		startup-delay-us = <100000>;
		regulator-boot-on;
		regulator-always-on;
		enable-active-high;
	};

	reg_espresso_external: regulator-espresso-external {
		compatible = "regulator-fixed";
		regulator-name = "vmmc1";
		regulator-max-microvolt = <2800000>;
		regulator-min-microvolt = <2800000>;
		gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; /* GPIO_34 */
		enable-active-high;
	};

	reg_touch_ldo_en: regulator-touch-ldo-en {
		compatible = "regulator-fixed";
		regulator-name = "touch_ldo_en";
		regulator-max-microvolt = <2800000>;
		regulator-min-microvolt = <2800000>;
		gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* GPIO_54 */
		regulator-always-on;
		enable-active-high;
	};

	gpio-keys {
		compatible = "gpio-keys";
		pinctrl-names = "default";
		pinctrl-0 = <&gpio_keys>;

		key-power {
			label = "power";

			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; /* GPIO_wk3 */
			linux,code = <KEY_POWER>;
			wakeup-source;
		};

		button-volup {
			linux,code = <KEY_VOLUMEUP>;
			label = "volume_up"; /* GPIO_wk30 */
			gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
		};

		button-voldown {
			linux,code = <KEY_VOLUMEDOWN>;
			label = "volume_down"; /* GPIO_wk8 */
			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
		};
	};

	reg_lcd: regulator-lcd {
		compatible = "regulator-fixed";
		regulator-name = "lcd_en";
		gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>; /* GPIO_135 */
		regulator-max-microvolt = <3300000>;
		regulator-min-microvolt = <3300000>;
		enable-active-high;
		regulator-boot-on;
	};

	pwm10: pwm-10 {
		pinctrl-names = "default";
		pinctrl-0 = <&pwm10_default>;
		compatible = "ti,omap-dmtimer-pwm";
		#pwm-cells = <3>;
		ti,timers = <&timer10>;
		ti,clock-source = <0x00>;
	};

	lvds-encoder {
		compatible = "doestek,dtc34lm85am", "lvds-encoder";
		powerdown-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; /* GPIO_136 */
		power-supply = <&reg_lcd>;
		ports {
			#address-cells = <1>;
			#size-cells = <0>;

			port@0 {
				reg = <0>;
				bridge_in: endpoint {
					remote-endpoint = <&dpi_out>;
				};
			};

			port@1 {
				reg = <1>;
				bridge_out: endpoint {
					remote-endpoint = <&panel_in>;
				};
			};
		};
	};

	vibrator {
		compatible = "gpio-vibrator";
		enable-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>; /* GPIO_38 */
		pinctrl-names = "default";
		pinctrl-0 = <&vibrator_default>;
	};

	gp2a_shunt: current-sense-shunt {
		compatible = "current-sense-shunt";
		io-channels = <&gpadc 4>;
		shunt-resistor-micro-ohms = <24000000>; /* 24 ohms */
		#io-channel-cells = <0>;
	};

	led-ir {
		compatible = "gpio-ir-tx";
		gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* GPIO_59 */
		pinctrl-names = "default";
		pinctrl-0 = <&ledir_pins>;
	};
};

&omap4_pmx_wkup {
	gpio_keys: gpio-keys-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x046, PIN_INPUT | MUX_MODE3)
			/* sim_cd.gpio_wk3 - EXT_WAKEUP */
			OMAP4_IOPAD(0x056, PIN_INPUT | MUX_MODE3)
			/* fref_clk3_req.gpio_wk30 - VOL_UP */
			OMAP4_IOPAD(0x05C, PIN_INPUT | MUX_MODE3)
			/* fref_clk4_out.gpio_wk8 - VOL_DN */
		>;
	};
};

&omap4_pmx_core {
	backlight_pins: pinmux-backlight-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0X0D8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3)
			/* usbb1_ulpitll_dat7.gpio_95 - LED_BACKLIGHT_RESET */
		>;
	};

	bluetooth_pins: pinmux-bluetooth-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
			/* gpmc_ncs6.gpio_103 - BT_EN */
			OMAP4_IOPAD(0x0be, PIN_OUTPUT | MUX_MODE3)
			/* cam_strobe.gpio_82 - BT_nRST */
			OMAP4_IOPAD(0x0c0, PIN_INPUT | MUX_MODE3)
			/* cam_globalreset.gpio_83 - BT_HOST_WAKE */
			OMAP4_IOPAD(0x0d4, PIN_OUTPUT | MUX_MODE3)
			/* usbb1_ulpitll_dat5.gpio_93 - BT_WAKE */
		>;
	};

	dss_dpi_pins: pinmux-dss-dpi-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x162, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data23 */
			OMAP4_IOPAD(0x164, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data22 */
			OMAP4_IOPAD(0x166, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data21 */
			OMAP4_IOPAD(0x168, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data20 */
			OMAP4_IOPAD(0x16a, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data19 */
			OMAP4_IOPAD(0x16c, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data18 */
			OMAP4_IOPAD(0x16e, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data15 */
			OMAP4_IOPAD(0x170, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data14 */
			OMAP4_IOPAD(0x172, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data13 */
			OMAP4_IOPAD(0x174, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data12 */
			OMAP4_IOPAD(0x176, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data11 */
			OMAP4_IOPAD(0x1b4, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data10 */
			OMAP4_IOPAD(0x1b6, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data9 */
			OMAP4_IOPAD(0x1b8, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data16 */
			OMAP4_IOPAD(0x1ba, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data17 */
			OMAP4_IOPAD(0x1bc, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_hsync */
			OMAP4_IOPAD(0x1be, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_pclk */
			OMAP4_IOPAD(0x1c0, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_vsync */
			OMAP4_IOPAD(0x1c2, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_de */
			OMAP4_IOPAD(0x1c4, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data8 */
			OMAP4_IOPAD(0x1c6, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data7 */
			OMAP4_IOPAD(0x1c8, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data6 */
			OMAP4_IOPAD(0x1ca, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data5 */
			OMAP4_IOPAD(0x1cc, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data4 */
			OMAP4_IOPAD(0x1ce, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data3 */

			OMAP4_IOPAD(0x1d0, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data2 */
			OMAP4_IOPAD(0x1d2, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data1 */
			OMAP4_IOPAD(0x1d4, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
			/* dispc2_data0 */
		>;
	};

	fuel_alert_irq: pinmux-fuel-alert-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE3)
			/* gpmc_a20.gpio_44 */
		>;
	};

	i2c1_pins: pinmux-i2c1-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0)
			/* i2c1_scl */
			OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0)
			/* i2c1_sda */
		>;
	};

	i2c2_pins: pinmux-i2c2-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0)
			/* i2c2_scl */
			OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0)
			/* i2c2_sda */
		>;
	};

	i2c3_pins: pinmux-i2c3-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0)
			/* i2c3_scl */
			OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0)
			/* i2c3_sda */
		>;
	};

	i2c4_pins: pinmux-i2c4-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0)
			/* i2c4_scl */
			OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0)
			/* i2c4_sda */
		>;
	};

	i2c5_pins: pinmux-i2c5-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x0de, PIN_INPUT_PULLUP | MUX_MODE3)
			/* usbc1_icusb_dp.gpio_98 */
			OMAP4_IOPAD(0x0e0, PIN_INPUT_PULLUP | MUX_MODE3)
			/* usbc1_icusb_dm.gpio_99 */
		>;
	};

	i2c6_pins: pinmux-i2c6-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE3)
			/* hdmi_ddc_scl.gpio_65 */
			OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE3)
			/* hdmi_ddc_sda.gpio_66 */
		>;
	};

	i2c7_pins: pinmux-i2c7-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x08a, PIN_INPUT_PULLUP | MUX_MODE3)
			/* gpmc_wait0.gpio_61 */
			OMAP4_IOPAD(0x08c, PIN_INPUT_PULLUP | MUX_MODE3)
			/* gpmc_wait1.gpio_62 */
		>;
	};

	ledir_pins: pimux-ledir-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x086, PIN_INPUT_PULLDOWN | MUX_MODE7)
			/* gpmc_nbe0_cle.gpio_59 */
			OMAP4_IOPAD(0x156, PIN_INPUT_PULLDOWN | MUX_MODE7)
			/* mcspi4_simo.gpio_152 */
		>;
	};

	lvds_pins: pinmux-lvds-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0X136, PIN_OUTPUT | MUX_MODE3)
			/* mcspi1_simo.gpio_136 - LVDS_nSHDN */
		>;
	};

	mmc1_pins: pinmux-mmc1-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x0e2, PIN_INPUT_PULLDOWN | MUX_MODE0)
			/* sdmmc1_clk */
			OMAP4_IOPAD(0x0e4, PIN_INPUT_PULLUP | MUX_MODE0)
			/* sdmcc1_cmd */
			OMAP4_IOPAD(0x0e6, PIN_INPUT_PULLUP | MUX_MODE0)
			/* sdmcc1_dat0 */
			OMAP4_IOPAD(0x0e8, PIN_INPUT_PULLUP | MUX_MODE0)
			/* sdmmc1_dat1 */
			OMAP4_IOPAD(0x0ea, PIN_INPUT_PULLUP | MUX_MODE0)
			/* sdmmc1_dat2 */
			OMAP4_IOPAD(0x0ec, PIN_INPUT_PULLUP | MUX_MODE0)
			/* sdmmc1_dat3 */
		>;
	};

	mmc2_pins: pinmux-mmc2-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x040, PIN_INPUT_PULLUP | MUX_MODE1)
			/* sdmmc2_dat0 */
			OMAP4_IOPAD(0x042, PIN_INPUT_PULLUP | MUX_MODE1)
			/* sdmmc2_dat1 */
			OMAP4_IOPAD(0x044, PIN_INPUT_PULLUP | MUX_MODE1)
			/* sdmmc2_dat2 */
			OMAP4_IOPAD(0x046, PIN_INPUT_PULLUP | MUX_MODE1)
			/* sdmmc2_dat3 */
			OMAP4_IOPAD(0x048, PIN_INPUT_PULLUP | MUX_MODE1)
			/* sdmmc2_dat4 */
			OMAP4_IOPAD(0x04a, PIN_INPUT_PULLUP | MUX_MODE1)
			/* sdmmc2_dat5 */
			OMAP4_IOPAD(0x04c, PIN_INPUT_PULLUP | MUX_MODE1)
			/* sdmmc2_dat6 */
			OMAP4_IOPAD(0x04e, PIN_INPUT_PULLUP | MUX_MODE1)
			/* sdmmc2_dat7 */
			OMAP4_IOPAD(0x082, PIN_INPUT_PULLUP | MUX_MODE1)
			/* sdmmc2_clk */
			OMAP4_IOPAD(0x084, PIN_INPUT_PULLUP | MUX_MODE1)
			/* sdmmc2_cmd */
		>;
	};

	mmc5_pins: pinmux-mmc5-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x148, PIN_INPUT_PULLDOWN | MUX_MODE0)
			/* sdmmc5_clk.sdmmc5_clk */
			OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0)
			/* sdmmc5_cmd.sdmmc5_cmd */
			OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0)
			/* sdmmc5_dat0.sdmmc5_dat0 */
			OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0)
			/* sdmmc5_dat1.sdmmc5_dat1 */
			OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0)
			/* sdmmc5_dat2.sdmmc5_dat2 */
			OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0)
			/* sdmmc5_dat3.sdmmc5_dat3 */
		>;
	};

	pwm10_default: pinmux-pwm10-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0X0D6, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE1)
			/* usbb1_ulpitll_dat6.dmtimer10_pwm_evt - LED_BACKLIGHT_PWM */
		>;
	};

	touch_pins: pinmux-touch-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x06c, PIN_INPUT | MUX_MODE3)
			/* gpmc_a22.gpio_46 - TSP_INT */
		>;
	};

	uart2_pins: pinmux-uart2-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0)
			/* uart2_cts.uart2_cts */
			OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE0)
			/* uart2_rts.uart2_rts */
			OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0)
			/* uart2_rx.uart2_rx */
			OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE0)
			/* uart2_tx.uart2_tx */
		>;
	};

	uart3_pins: pinmux-uart3-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x144, PIN_INPUT | MUX_MODE0)
			/* uart3_rx_irrx */
			OMAP4_IOPAD(0x146, PIN_OUTPUT | MUX_MODE0)
			/* uart3_tx_irtx */
		>;
	};

	vibrator_default: pinmux-vibrator-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x05c, PIN_INPUT_PULLDOWN | MUX_MODE3)
			/* gpmc_ad14.gpio_38 - MOTOR_EN */
		>;
	};

	wlanen_gpio: pinmux-wlanen-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
			/* gpmc_ncs7.gpio_104 */
		>;
	};

	wlan_host_wake: pinmux-wlan-host-wake-pins {
		pinctrl-single,pins = <
			OMAP4_IOPAD(0x0bc, PIN_INPUT | MUX_MODE3)
			/* cam_shutter.gpio_81 - WLAN_HOST_WAKE */
		>;
	};
};

&uart3 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart3_pins>;

	interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
				   &omap4_pmx_core OMAP4_UART3_RX>;
};

&i2c1 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c1_pins>;

	clock-frequency = <400000>;

	twl: pmic@48 {
		reg = <0x48>;
		#clock-cells = <1>;

		pinctrl-names = "default";
		pinctrl-0 = <
			&twl6030_pins
			&twl6030_wkup_pins
		>;

		/* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
		interrupt-parent = <&gic>;
		system-power-controller;
	};
};

#include "twl6032.dtsi"
#include "twl6030_omap4.dtsi"

&ldo1 {
	regulator-min-microvolt = <2800000>;
	regulator-max-microvolt = <2800000>;
	regulator-always-on;
	regulator-state-mem {
		regulator-off-in-suspend;
	};
};

&ldo3 {
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-always-on;
	regulator-state-mem {
		regulator-off-in-suspend;
	};
};

&ldo4 {
	regulator-min-microvolt = <2800000>;
	regulator-max-microvolt = <2800000>;
	regulator-always-on;
};

&ldo5 {
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-always-on;
};

&ldo6 {
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-always-on;
	regulator-state-mem {
		regulator-off-in-suspend;
	};
};

&smps4 {
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-always-on;
};

&ldousb {
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-always-on;
};

&i2c2 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c2_pins>;
};

&i2c3 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c3_pins>;
};

&i2c4 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c4_pins>;

	accelerometer@18 {
		compatible = "bosch,bma254";
		reg = <0x18>;
		vdd-supply = <&ldo4>;
		vddio-supply = <&ldo5>;
		interrupt-parent = <&gpio4>;
		interrupts = <25 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>,
			<26 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>;
	};

	magnetometer@2e {
		compatible = "yamaha,yas530";
		reg = <0x2e>;
		vdd-supply = <&ldo4>;
		iovdd-supply = <&ldo5>;
		reset-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
		interrupts = <&gpio6 10 IRQ_TYPE_EDGE_RISING>;
	};

	light-sensor@44 {
		compatible = "sharp,gp2ap002a00f";
		reg = <0x44>;
		interrupt-parent = <&gpio1>;
		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
		vdd-supply = <&ldo4>;
		vio-supply = <&ldo4>;
		io-channels = <&gp2a_shunt>;
		io-channel-names = "alsout";
		sharp,proximity-far-hysteresis = /bits/ 8 <0x40>;
		sharp,proximity-close-hysteresis = /bits/ 8 <0x20>;
	};
};

&dss {
	status = "okay";

	pinctrl-names = "default";
	pinctrl-0 = <&dss_dpi_pins>;

	port {
		dpi_out: endpoint {
			remote-endpoint = <&bridge_in>;
			data-lines = <24>;
		};
	};
};

&twl_usb_comparator {
	usb-supply = <&ldousb>;
};

&usb_otg_hs {
	interface-type = <1>;
	mode = <3>;
	power = <50>;
};

&mmc1 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&mmc1_pins>;

	vmmc-supply = <&reg_espresso_external>;
	bus-width = <4>;
};

&mmc2 {
	pinctrl-names = "default";
	pinctrl-0 = <&mmc2_pins>;

	vmmc-supply = <&reg_espresso_internal>;
	ti,non-removable;
	bus-width = <8>;
};

&mmc3 {
	status = "disabled";
};

&mmc4 {
	status = "disabled";
};

&mmc5 {
	status = "okay";

	#address-cells = <1>;
	#size-cells = <0>;

	non-removable;
	bus-width = <4>;
	vmmc-supply = <&reg_espresso_wlan>;
	mmc-pwrseq = <&wlan_pwrseq>;

	pinctrl-names = "default";
	pinctrl-0 = <&mmc5_pins>;

	brcmf: wifi@1 {
		compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
		reg = <1>;

		interrupt-parent = <&gpio3>;
		interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-names = "host-wake";
		pinctrl-names = "default";
		pinctrl-0 = <&wlan_host_wake>;
	};
};

&uart2 {
	interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
				&omap4_pmx_core OMAP4_UART2_RX>;
	pinctrl-names = "default";
	pinctrl-0 = <&uart2_pins>;
	bluetooth {
		compatible = "brcm,bcm4330-bt";
		pinctrl-names = "default";
		pinctrl-0 = <&bluetooth_pins>;
		shutdown-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>;
		reset-gpios = <&gpio3 18 GPIO_ACTIVE_LOW>;
		device-wakeup-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
		interrupt-parent = <&gpio3>;
		interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
		interrupt-names = "host-wakeup";
	};
};