// SPDX-License-Identifier: GPL-2.0-only
/*
* Libata based driver for Apple "macio" family of PATA controllers
*
* Copyright 2008/2009 Benjamin Herrenschmidt, IBM Corp
* <benh@kernel.crashing.org>
*
* Some bits and pieces from drivers/ide/ppc/pmac.c
*
*/
#undef DEBUG
#undef DEBUG_DMA
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/ata.h>
#include <linux/libata.h>
#include <linux/adb.h>
#include <linux/pmu.h>
#include <linux/scatterlist.h>
#include <linux/irqdomain.h>
#include <linux/of.h>
#include <linux/gfp.h>
#include <linux/pci.h>
#include <scsi/scsi.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_device.h>
#include <asm/macio.h>
#include <asm/io.h>
#include <asm/dbdma.h>
#include <asm/machdep.h>
#include <asm/pmac_feature.h>
#include <asm/mediabay.h>
#ifdef DEBUG_DMA
#define dev_dbgdma(dev, format, arg...) \
dev_printk(KERN_DEBUG , dev , format , ## arg)
#else
#define dev_dbgdma(dev, format, arg...) \
({ if (0) dev_printk(KERN_DEBUG, dev, format, ##arg); 0; })
#endif
#define DRV_NAME "pata_macio"
#define DRV_VERSION "0.9"
/* Models of macio ATA controller */
enum {
controller_ohare, /* OHare based */
controller_heathrow, /* Heathrow/Paddington */
controller_kl_ata3, /* KeyLargo ATA-3 */
controller_kl_ata4, /* KeyLargo ATA-4 */
controller_un_ata6, /* UniNorth2 ATA-6 */
controller_k2_ata6, /* K2 ATA-6 */
controller_sh_ata6, /* Shasta ATA-6 */
};
static const char* macio_ata_names[] = {
"OHare ATA", /* OHare based */
"Heathrow ATA", /* Heathrow/Paddington */
"KeyLargo ATA-3", /* KeyLargo ATA-3 (MDMA only) */
"KeyLargo ATA-4", /* KeyLargo ATA-4 (UDMA/66) */
"UniNorth ATA-6", /* UniNorth2 ATA-6 (UDMA/100) */
"K2 ATA-6", /* K2 ATA-6 (UDMA/100) */
"Shasta ATA-6", /* Shasta ATA-6 (UDMA/133) */
};
/*
* Extra registers, both 32-bit little-endian
*/
#define IDE_TIMING_CONFIG 0x200
#define IDE_INTERRUPT 0x300
/* Kauai (U2) ATA has different register setup */
#define IDE_KAUAI_PIO_CONFIG 0x200
#define IDE_KAUAI_ULTRA_CONFIG 0x210
#define IDE_KAUAI_POLL_CONFIG 0x220
/*
* Timing configuration register definitions
*/
/* Number of IDE_SYSCLK_NS ticks, argument is in nanoseconds */
#define SYSCLK_TICKS(t) (((t) + IDE_SYSCLK_NS - 1) / IDE_SYSCLK_NS)
#define SYSCLK_TICKS_66(t) (((t) + IDE_SYSCLK_66_NS - 1) / IDE_SYSCLK_66_NS)
#define IDE_SYSCLK_NS 30 /* 33Mhz cell */
#define IDE_SYSCLK_66_NS 15 /* 66Mhz cell */
/* 133Mhz cell, found in shasta.
* See comments about 100 Mhz Uninorth 2...
* Note that PIO_MASK and MDMA_MASK seem to overlap, that's just
* weird and I don't now why .. at this stage
*/
#define TR_133_PIOREG_PIO_MASK 0xff000fff
#define TR_133_PIOREG_MDMA_MASK 0x00fff800
#define TR_133_UDMAREG_UDMA_MASK 0x0003ffff
#define TR_133_UDMAREG_UDMA_EN 0x00000001
/* 100Mhz cell, found in Uninorth 2 and K2. It appears as a pci device
* (106b/0033) on uninorth or K2 internal PCI bus and it's clock is
* controlled like gem or fw. It appears to be an evolution of keylargo
* ATA4 with a timing register extended to 2x32bits registers (one
* for PIO & MWDMA and one for UDMA, and a similar DBDMA channel.
* It has it's own local feature control register as well.
*
* After scratching my mind over the timing values, at least for PIO
* and MDMA, I think I've figured the format of the timing register,
* though I use pre-calculated tables for UDMA as usual...
*/
#define TR_100_PIO_ADDRSETUP_MASK 0xff000000 /* Size of field unknown */
#define TR_100_PIO_ADDRSETUP_SHIFT 24
#define TR_100_MDMA_MASK 0x00fff000
#define TR_100_MDMA_RECOVERY_MASK 0x00fc0000
#define TR_100_MDMA_RECOVERY_SHIFT 18
#define TR_100_MDMA_ACCESS_MASK 0x0003f000
#define TR_100_MDMA_ACCESS_SHIFT 12
#define TR_100_PIO_MASK 0xff000fff
#define TR_100_PIO_RECOVERY_MASK 0x00000fc0
#define TR_100_PIO_RECOVERY_SHIFT 6
#define TR_100_PIO_ACCESS_MASK 0x0000003f
#define TR_100_PIO_ACCESS_SHIFT 0
#define TR_100_UDMAREG_UDMA_MASK 0x0000ffff
#define TR_100_UDMAREG_UDMA_EN 0x00000001
/* 66Mhz cell, found in KeyLargo. Can do ultra mode 0 to 2 on
* 40 connector cable and to 4 on 80 connector one.
* Clock unit is 15ns (66Mhz)
*
* 3 Values can be programmed:
* - Write data setup, which appears to match the cycle time. They
* also call it DIOW setup.
* - Ready to pause time (from spec)
* - Address setup. That one is weird. I don't see where exactly
* it fits in UDMA cycles, I got it's name from an obscure piece
* of commented out code in Darwin. They leave it to 0, we do as
* well, despite a comment that would lead to think it has a
* min value of 45ns.
* Apple also add 60ns to the write data setup (or cycle time ?) on
* reads.
*/
#define TR_66_UDMA_MASK 0xfff00000
#define TR_66_UDMA_EN 0x00100000 /* Enable Ultra mode for DMA */
#define TR_66_PIO_ADDRSETUP_MASK 0xe0000000 /* Address setup */
#define TR_66_PIO_ADDRSETUP_SHIFT 29
#define TR_66_UDMA_RDY2PAUS_MASK 0x1e000000 /* Ready 2 pause time */
#define TR_66_UDMA_RDY2PAUS_SHIFT 25
#define TR_66_UDMA_WRDATASETUP_MASK 0x01e00000 /* Write data setup time */
#define TR_66_UDMA_WRDATASETUP_SHIFT 21
#define TR_66_MDMA_MASK 0x000ffc00
#define TR_66_MDMA_RECOVERY_MASK 0x000f8000
#define TR_66_MDMA_RECOVERY_SHIFT 15
#define TR_66_MDMA_ACCESS_MASK 0x00007c00
#define TR_66_MDMA_ACCESS_SHIFT 10
#define TR_66_PIO_MASK 0xe00003ff
#define TR_66_PIO_RECOVERY_MASK 0x000003e0
#define TR_66_PIO_RECOVERY_SHIFT 5
#define TR_66_PIO_ACCESS_MASK 0x0000001f
#define TR_66_PIO_ACCESS_SHIFT 0
/* 33Mhz cell, found in OHare, Heathrow (& Paddington) and KeyLargo
* Can do pio & mdma modes, clock unit is 30ns (33Mhz)
*
* The access time and recovery time can be programmed. Some older
* Darwin code base limit OHare to 150ns cycle time. I decided to do
* the same here fore safety against broken old hardware ;)
* The HalfTick bit, when set, adds half a clock (15ns) to the access
* time and removes one from recovery. It's not supported on KeyLargo
* implementation afaik. The E bit appears to be set for PIO mode 0 and
* is used to reach long timings used in this mode.
*/
#define TR_33_MDMA_MASK 0x003ff800
#define TR_33_MDMA_RECOVERY_MASK 0x001f0000
#define TR_33_MDMA_RECOVERY_SHIFT 16
#define TR_33_MDMA_ACCESS_MASK 0x0000f800
#define TR_33_MDMA_ACCESS_SHIFT 11
#define TR_33_MDMA_HALFTICK 0x00200000
#define TR_33_PIO_MASK 0x000007ff
#define TR_33_PIO_E 0x00000400
#define TR_33_PIO_RECOVERY_MASK 0x000003e0
#define TR_33_PIO_RECOVERY_SHIFT 5
#define TR_33_PIO_ACCESS_MASK 0x0000001f
#define TR_33_PIO_ACCESS_SHIFT 0
/*
* Interrupt register definitions. Only present on newer cells
* (Keylargo and later afaik) so we don't use it.
*/
#define IDE_INTR_DMA 0x80000000
#define IDE_INTR_DEVICE 0x40000000
/*
* FCR Register on Kauai. Not sure what bit 0x4 is ...
*/
#define KAUAI_FCR_UATA_MAGIC 0x00000004
#define KAUAI_FCR_UATA_RESET_N 0x00000002
#define KAUAI_FCR_UATA_ENABLE 0x00000001
/* Allow up to 256 DBDMA commands per xfer */
#define MAX_DCMDS 256
/* Don't let a DMA segment go all the way to 64K */
#define MAX_DBDMA_SEG 0xff00
/*
* Wait 1s for disk to answer on IDE bus after a hard reset
* of the device (via GPIO/FCR).
*
* Some devices seem to "pollute" the bus even after dropping
* the BSY bit (typically some combo drives slave on the UDMA
* bus) after a hard reset. Since we hard reset all drives on
* KeyLargo ATA66, we have to keep that delay around. I may end
* up not hard resetting anymore on these and keep the delay only
* for older interfaces instead (we have to reset when coming
* from MacOS...) --BenH.
*/
#define IDE_WAKEUP_DELAY_MS 1000
struct pata_macio_timing;
struct pata_macio_priv {
int kind;
int aapl_bus_id;
int mediabay : 1;
struct device_node *node;
struct macio_dev *mdev;
struct pci_dev *pdev;
struct device *dev;
int irq;
u32 treg[2][2];
void __iomem *tfregs;
void __iomem *kauai_fcr;
struct dbdma_cmd * dma_table_cpu;
dma_addr_t dma_table_dma;
struct ata_host *host;
const struct pata_macio_timing *timings;
};
/* Previous variants of this driver used to calculate timings
* for various variants of the chip and use tables for others.
*
* Not only was this confusing, but in addition, it isn't clear
* whether our calculation code was correct. It didn't entirely
* match the darwin code and whatever documentation I could find
* on these cells
*
* I decided to entirely rely on a table instead for this version
* of the driver. Also, because I don't really care about derated
* modes and really old HW other than making it work, I'm not going
* to calculate / snoop timing values for something else than the
* standard modes.
*/
struct pata_macio_timing {
int mode;
u32 reg1; /* Bits to set in first timing reg */
u32 reg2; /* Bits to set in second timing reg */
};
static const struct pata_macio_timing pata_macio_ohare_timings[] = {
{ XFER_PIO_0, 0x00000526, 0, },
{ XFER_PIO_1, 0x00000085, 0, },
{ XFER_PIO_2, 0x00000025, 0, },
{ XFER_PIO_3, 0x00000025, 0, },
{ XFER_PIO_4, 0x00000025, 0, },
{ XFER_MW_DMA_0, 0x00074000, 0, },
{ XFER_MW_DMA_1, 0x00221000, 0, },
{ XFER_MW_DMA_2, 0x00211000, 0, },
{ -1, 0, 0 }
};
static const struct pata_macio_timing pata_macio_heathrow_timings[] = {
{ XFER_PIO_0, 0x00000526, 0, },
{ XFER_PIO_1, 0x00000085, 0, },
{ XFER_PIO_2, 0x00000025, 0, },
{ XFER_PIO_3, 0x00000025, 0, },
{ XFER_PIO_4, 0x00000025, 0, },
{ XFER_MW_DMA_0, 0x00074000, 0, },
{ XFER_MW_DMA_1, 0x00221000, 0, },
{ XFER_MW_DMA_2, 0x00211000, 0, },
{ -1, 0, 0 }
};
static const struct pata_macio_timing pata_macio_kl33_timings[] = {
{ XFER_PIO_0, 0x00000526, 0, },
{ XFER_PIO_1, 0x00000085, 0, },
{ XFER_PIO_2, 0x00000025, 0, },
{ XFER_PIO_3, 0x00000025, 0, },
{ XFER_PIO_4, 0x00000025, 0, },
{ XFER_MW_DMA_0, 0x00084000, 0, },
{ XFER_MW_DMA_1, 0x00021800, 0, },
{ XFER_MW_DMA_2, 0x00011800, 0, },
{ -1, 0, 0 }
};
static const struct pata_macio_timing pata_macio_kl66_timings[] = {
{ XFER_PIO_0, 0x0000038c, 0, },
{ XFER_PIO_1, 0x0000020a, 0, },
{ XFER_PIO_2, 0x00000127, 0, },
{ XFER_PIO_3, 0x000000c6, 0, },
{ XFER_PIO_4, 0x00000065, 0, },
{ XFER_MW_DMA_0, 0x00084000, 0, },
{ XFER_MW_DMA_1, 0x00029800, 0, },
{ XFER_MW_DMA_2, 0x00019400, 0, },
{ XFER_UDMA_0, 0x19100000, 0, },
{ XFER_UDMA_1, 0x14d00000, 0, },
{ XFER_UDMA_2, 0x10900000, 0, },
{ XFER_UDMA_3, 0x0c700000, 0, },
{ XFER_UDMA_4, 0x0c500000, 0, },
{ -1, 0, 0 }
};
static const struct pata_macio_timing pata_macio_kauai_timings[] = {
{ XFER_PIO_0, 0x08000a92, 0, },
{ XFER_PIO_1, 0x0800060f, 0, },
{ XFER_PIO_2, 0x0800038b, 0, },
{ XFER_PIO_3, 0x05000249, 0, },
{ XFER_PIO_4, 0x04000148, 0, },
{ XFER_MW_DMA_0, 0x00618000, 0, },
{ XFER_MW_DMA_1, 0x00209000, 0, },
{ XFER_MW_DMA_2, 0x00148000, 0, },
{ XFER_UDMA_0, 0, 0x000070c1, },
{ XFER_UDMA_1, 0, 0x00005d81, },
{ XFER_UDMA_2, 0, 0x00004a61, },
{ XFER_UDMA_3, 0, 0x00003a51, },
{ XFER_UDMA_4, 0, 0x00002a31, },
{ XFER_UDMA_5, 0, 0x00002921, },
{ -1, 0, 0 }
};
static const struct pata_macio_timing pata_macio_shasta_timings[] = {
{ XFER_PIO_0, 0x0a000c97, 0, },
{ XFER_PIO_1, 0x07000712, 0, },
{ XFER_PIO_2, 0x040003cd, 0, },
{ XFER_PIO_3, 0x0500028b, 0, },
{ XFER_PIO_4, 0x0400010a, 0, },
{ XFER_MW_DMA_0, 0x00820800, 0, },
{ XFER_MW_DMA_1, 0x0028b000, 0, },
{ XFER_MW_DMA_2, 0x001ca000, 0, },
{ XFER_UDMA_0, 0, 0x00035901, },
{ XFER_UDMA_1, 0, 0x000348b1, },
{ XFER_UDMA_2, 0, 0x00033881, },
{ XFER_UDMA_3, 0, 0x00033861, },
{ XFER_UDMA_4, 0, 0x00033841, },
{ XFER_UDMA_5, 0, 0x00033031, },
{ XFER_UDMA_6, 0, 0x00033021, },
{ -1, 0, 0 }
};
static const struct pata_macio_timing *pata_macio_find_timing(
struct pata_macio_priv *priv,
int mode)
{
int i;
for (i = 0; priv->timings[i].mode > 0; i++) {
if (priv->timings[i].mode == mode)
return &priv->timings[i];
}
return NULL;
}
static void pata_macio_apply_timings(struct ata_port *ap, unsigned int device)
{
struct pata_macio_priv *priv = ap->private_data;
void __iomem *rbase = ap->ioaddr.cmd_addr;
if (priv->kind == controller_sh_ata6 ||
priv->kind == controller_un_ata6 ||
priv->kind == controller_k2_ata6) {
writel(priv->treg[device][0], rbase + IDE_KAUAI_PIO_CONFIG);
writel(priv->treg[device][1], rbase + IDE_KAUAI_ULTRA_CONFIG);
} else
writel(priv->treg[device][0], rbase + IDE_TIMING_CONFIG);
}
static void pata_macio_dev_select(struct ata_port *ap, unsigned int device)
{
ata_sff_dev_select(ap, device);
/* Apply timings */
pata_macio_apply_timings(ap, device);
}
static void pata_macio_set_timings(struct ata_port *ap,
struct ata_device *adev)
{
struct pata_macio_priv *priv = ap->private_data;
const struct pata_macio_timing *t;
dev_dbg(priv->dev, "Set timings: DEV=%d,PIO=0x%x (%s),DMA=0x%x (%s)\n",
adev->devno,
adev->pio_mode,
ata_mode_string(ata_xfer_mode2mask(adev->pio_mode)),
adev->dma_mode,
ata_mode_string(ata_xfer_mode2mask(adev->dma_mode)));
/* First clear timings */
priv->treg[adev->devno][0] = priv->treg[adev->devno][1] = 0;
/* Now get the PIO timings */
t = pata_macio_find_timing(priv, adev->pio_mode);
if (t == NULL) {
dev_warn(priv->dev, "Invalid PIO timing requested: 0x%x\n",
adev->pio_mode);
t = pata_macio_find_timing(priv, XFER_PIO_0);
}
BUG_ON(t == NULL);
/* PIO timings only ever use the first treg */
priv->treg[adev->devno][0] |= t->reg1;
/* Now get DMA timings */
t = pata_macio_find_timing(priv, adev->dma_mode);
if (t == NULL || (t->reg1 == 0 && t->reg2 == 0)) {
dev_dbg(priv->dev, "DMA timing not set yet, using MW_DMA_0\n");
t = pata_macio_find_timing(priv, XFER_MW_DMA_0);
}
BUG_ON(t == NULL);
/* DMA timings can use both tregs */
priv->treg[adev->devno][0] |= t->reg1;
priv->treg[adev->devno][1] |= t->reg2;
dev_dbg(priv->dev, " -> %08x %08x\n",
priv->treg[adev->devno][0],
priv->treg[adev->devno][1]);
/* Apply to hardware */
pata_macio_apply_timings(ap, adev->devno);
}
/*
* Blast some well known "safe" values to the timing registers at init or
* wakeup from sleep time, before we do real calculation
*/
static void pata_macio_default_timings(struct pata_macio_priv *priv)
{
unsigned int value, value2 = 0;
switch(priv->kind) {
case controller_sh_ata6:
value = 0x0a820c97;
value2 = 0x00033031;
break;
case controller_un_ata6:
case controller_k2_ata6:
value = 0x08618a92;
value2 = 0x00002921;
break;
case controller_kl_ata4:
value = 0x0008438c;
break;
case controller_kl_ata3:
value = 0x00084526;
break;
case controller_heathrow:
case controller_ohare:
default:
value = 0x00074526;
break;
}
priv->treg[0][0] = priv->treg[1][0] = value;
priv->treg[0][1] = priv->treg[1][1] = value2;
}
static int pata_macio_cable_detect(struct ata_port *ap)
{
struct pata_macio_priv *priv = ap->private_data;
/* Get cable type from device-tree */
if (priv->kind == controller_kl_ata4 ||
priv->kind == controller_un_ata6 ||
priv->kind == controller_k2_ata6 ||
priv->kind == controller_sh_ata6) {
const char* cable = of_get_property(priv->node, "cable-type",
NULL);
struct device_node *root = of_find_node_by_path("/");
const char *model = of_get_property(root, "model", NULL);
of_node_put(root);
if (cable && !strncmp(cable, "80-", 3)) {
/* Some drives fail to detect 80c cable in PowerBook
* These machine use proprietary short IDE cable
* anyway
*/
if (!strncmp(model, "PowerBook", 9))
return ATA_CBL_PATA40_SHORT;
else
return ATA_CBL_PATA80;
}
}
/* G5's seem to have incorrect cable type in device-tree.
* Let's assume they always have a 80 conductor cable, this seem to
* be always the case unless the user mucked around
*/
if (of_device_is_compatible(priv->node, "K2-UATA") ||
of_device_is_compatible(priv->node, "shasta-ata"))
return ATA_CBL_PATA80;
/* Anything else is 40 connectors */
return ATA_CBL_PATA40;
}
static enum ata_completion_errors pata_macio_qc_prep(struct ata_queued_cmd *qc)
{
unsigned int write = (qc->tf.flags & ATA_TFLAG_WRITE);
struct ata_port *ap = qc->ap;
struct pata_macio_priv *priv = ap->private_data;
struct scatterlist *sg;
struct dbdma_cmd *table;
unsigned int si, pi;
dev_dbgdma(priv->dev, "%s: qc %p flags %lx, write %d dev %d\n",
__func__, qc, qc->flags, write, qc->dev->devno);
if (!(qc->flags & ATA_QCFLAG_DMAMAP))
return AC_ERR_OK;
table = (struct dbdma_cmd *) priv->dma_table_cpu;
pi = 0;
for_each_sg(qc->sg, sg, qc->n_elem, si) {
u32 addr, sg_len, len;
/* determine if physical DMA addr spans 64K boundary.
* Note h/w doesn't support 64-bit, so we unconditionally
* truncate dma_addr_t to u32.
*/
addr = (u32) sg_dma_address(sg);
sg_len = sg_dma_len(sg);
while (sg_len) {
/* table overflow should never happen */
BUG_ON (pi++ >= MAX_DCMDS);
len = (sg_len < MAX_DBDMA_SEG) ? sg_len : MAX_DBDMA_SEG;
table->command = cpu_to_le16(write ? OUTPUT_MORE: INPUT_MORE);
table->req_count = cpu_to_le16(len);
table->phy_addr = cpu_to_le32(addr);
table->cmd_dep = 0;
table->xfer_status = 0;
table->res_count = 0;
addr += len;
sg_len -= len;
++table;
}
}
/* Should never happen according to Tejun */
BUG_ON(!pi);
/* Convert the last command to an input/output */
table--;
table->command = cpu_to_le16(write ? OUTPUT_LAST: INPUT_LAST);
table++;
/* Add the stop command to the end of the list */
memset(table, 0, sizeof(struct dbdma_cmd));
table->command = cpu_to_le16(DBDMA_STOP);
dev_dbgdma(priv->dev, "%s: %d DMA list entries\n", __func__, pi);
return AC_ERR_OK;
}
static void pata_macio_freeze(struct ata_port *ap)
{
struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
if (dma_regs) {
unsigned int timeout = 1000000;
/* Make sure DMA controller is stopped */
writel((RUN|PAUSE|FLUSH|WAKE|DEAD) << 16, &dma_regs->control);
while (--timeout && (readl(&dma_regs->status) & RUN))
udelay(1);
}
ata_sff_freeze(ap);
}
static void pata_macio_bmdma_setup(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct pata_macio_priv *priv = ap->private_data;
struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
int dev = qc->dev->devno;
dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);
/* Make sure DMA commands updates are visible */
writel(priv->dma_table_dma, &dma_regs->cmdptr);
/* On KeyLargo 66Mhz cell, we need to add 60ns to wrDataSetup on
* UDMA reads
*/
if (priv->kind == controller_kl_ata4 &&
(priv->treg[dev][0] & TR_66_UDMA_EN)) {
void __iomem *rbase = ap->ioaddr.cmd_addr;
u32 reg = priv->treg[dev][0];
if (!(qc->tf.flags & ATA_TFLAG_WRITE))
reg += 0x00800000;
writel(reg, rbase + IDE_TIMING_CONFIG);
}
/* issue r/w command */
ap->ops->sff_exec_command(ap, &qc->tf);
}
static void pata_macio_bmdma_start(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct pata_macio_priv *priv = ap->private_data;
struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);
writel((RUN << 16) | RUN, &dma_regs->control);
/* Make sure it gets to the controller right now */
(void)readl(&dma_regs->control);
}
static void pata_macio_bmdma_stop(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct pata_macio_priv *priv = ap->private_data;
struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
unsigned int timeout = 1000000;
dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);
/* Stop the DMA engine and wait for it to full halt */
writel (((RUN|WAKE|DEAD) << 16), &dma_regs->control);
while (--timeout && (readl(&dma_regs->status) & RUN))
udelay(1);
}
static u8 pata_macio_bmdma_status(struct ata_port *ap)
{
struct pata_macio_priv *priv = ap->private_data;
struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
u32 dstat, rstat = ATA_DMA_INTR;
unsigned long timeout = 0;
dstat = readl(&dma_regs->status);
dev_dbgdma(priv->dev, "%s: dstat=%x\n", __func__, dstat);
/* We have two things to deal with here:
*
* - The dbdma won't stop if the command was started
* but completed with an error without transferring all
* datas. This happens when bad blocks are met during
* a multi-block transfer.
*
* - The dbdma fifo hasn't yet finished flushing to
* system memory when the disk interrupt occurs.
*/
/* First check for errors */
if ((dstat & (RUN|DEAD)) != RUN)
rstat |= ATA_DMA_ERR;
/* If ACTIVE is cleared, the STOP command has been hit and
* the transfer is complete. If not, we have to flush the
* channel.
*/
if ((dstat & ACTIVE) == 0)
return rstat;
dev_dbgdma(priv->dev, "%s: DMA still active, flushing...\n", __func__);
/* If dbdma didn't execute the STOP command yet, the
* active bit is still set. We consider that we aren't
* sharing interrupts (which is hopefully the case with
* those controllers) and so we just try to flush the
* channel for pending data in the fifo
*/
udelay(1);
writel((FLUSH << 16) | FLUSH, &dma_regs->control);
for (;;) {
udelay(1);
dstat = readl(&dma_regs->status);
if ((dstat & FLUSH) == 0)
break;
if (++timeout > 1000) {
dev_warn(priv->dev, "timeout flushing DMA\n");
rstat |= ATA_DMA_ERR;
break;
}
}
return rstat;
}
/* port_start is when we allocate the DMA command list */
static int pata_macio_port_start(struct ata_port *ap)
{
struct pata_macio_priv *priv = ap->private_data;
if (ap->ioaddr.bmdma_addr == NULL)
return 0;
/* Allocate space for the DBDMA commands.
*
* The +2 is +1 for the stop command and +1 to allow for
* aligning the start address to a multiple of 16 bytes.
*/
priv->dma_table_cpu =
dmam_alloc_coherent(priv->dev,
(MAX_DCMDS + 2) * sizeof(struct dbdma_cmd),
&priv->dma_table_dma, GFP_KERNEL);
if (priv->dma_table_cpu == NULL) {
dev_err(priv->dev, "Unable to allocate DMA command list\n");
ap->ioaddr.bmdma_addr = NULL;
ap->mwdma_mask = 0;
ap->udma_mask = 0;
}
return 0;
}
static void pata_macio_irq_clear(struct ata_port *ap)
{
struct pata_macio_priv *priv = ap->private_data;
/* Nothing to do here */
dev_dbgdma(priv->dev, "%s\n", __func__);
}
static void pata_macio_reset_hw(struct pata_macio_priv *priv, int resume)
{
dev_dbg(priv->dev, "Enabling & resetting... \n");
if (priv->mediabay)
return;
if (priv->kind == controller_ohare && !resume) {
/* The code below is having trouble on some ohare machines
* (timing related ?). Until I can put my hand on one of these
* units, I keep the old way
*/
ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, priv->node, 0, 1);
} else {
int rc;
/* Reset and enable controller */
rc = ppc_md.feature_call(PMAC_FTR_IDE_RESET,
priv->node, priv->aapl_bus_id, 1);
ppc_md.feature_call(PMAC_FTR_IDE_ENABLE,
priv->node, priv->aapl_bus_id, 1);
msleep(10);
/* Only bother waiting if there's a reset control */
if (rc == 0) {
ppc_md.feature_call(PMAC_FTR_IDE_RESET,
priv->node, priv->aapl_bus_id, 0);
msleep(IDE_WAKEUP_DELAY_MS);
}
}
/* If resuming a PCI device, restore the config space here */
if (priv->pdev && resume) {
int rc;
pci_restore_state(priv->pdev);
rc = pcim_enable_device(priv->pdev);
if (rc)
dev_err(&priv->pdev->dev,
"Failed to enable device after resume (%d)\n",
rc);
else
pci_set_master(priv->pdev);
}
/* On Kauai, initialize the FCR. We don't perform a reset, doesn't really
* seem necessary and speeds up the boot process
*/
if (priv->kauai_fcr)
writel(KAUAI_FCR_UATA_MAGIC |
KAUAI_FCR_UATA_RESET_N |
KAUAI_FCR_UATA_ENABLE, priv->kauai_fcr);
}
/* Hook the standard slave config to fixup some HW related alignment
* restrictions
*/
static int pata_macio_slave_config(struct scsi_device *sdev)
{
struct ata_port *ap = ata_shost_to_port(sdev->host);
struct pata_macio_priv *priv = ap->private_data;
struct ata_device *dev;
u16 cmd;
int rc;
/* First call original */
rc = ata_scsi_slave_config(sdev);
if (rc)
return rc;
/* This is lifted from sata_nv */
dev = &ap->link.device[sdev->id];
/* OHare has issues with non cache aligned DMA on some chipsets */
if (priv->kind == controller_ohare) {
blk_queue_update_dma_alignment(sdev->request_queue, 31);
blk_queue_update_dma_pad(sdev->request_queue, 31);
/* Tell the world about it */
ata_dev_info(dev, "OHare alignment limits applied\n");
return 0;
}
/* We only have issues with ATAPI */
if (dev->class != ATA_DEV_ATAPI)
return 0;
/* Shasta and K2 seem to have "issues" with reads ... */
if (priv->kind == controller_sh_ata6 || priv->kind == controller_k2_ata6) {
/* Allright these are bad, apply restrictions */
blk_queue_update_dma_alignment(sdev->request_queue, 15);
blk_queue_update_dma_pad(sdev->request_queue, 15);
/* We enable MWI and hack cache line size directly here, this
* is specific to this chipset and not normal values, we happen
* to somewhat know what we are doing here (which is basically
* to do the same Apple does and pray they did not get it wrong :-)
*/
BUG_ON(!priv->pdev);
pci_write_config_byte(priv->pdev, PCI_CACHE_LINE_SIZE, 0x08);
pci_read_config_word(priv->pdev, PCI_COMMAND, &cmd);
pci_write_config_word(priv->pdev, PCI_COMMAND,
cmd | PCI_COMMAND_INVALIDATE);
/* Tell the world about it */
ata_dev_info(dev, "K2/Shasta alignment limits applied\n");
}
return 0;
}
#ifdef CONFIG_PM_SLEEP
static int pata_macio_do_suspend(struct pata_macio_priv *priv, pm_message_t mesg)
{
/* First, core libata suspend to do most of the work */
ata_host_suspend(priv->host, mesg);
/* Restore to default timings */
pata_macio_default_timings(priv);
/* Mask interrupt. Not strictly necessary but old driver did
* it and I'd rather not change that here */
disable_irq(priv->irq);
/* The media bay will handle itself just fine */
if (priv->mediabay)
return 0;
/* Kauai has bus control FCRs directly here */
if (priv->kauai_fcr) {
u32 fcr = readl(priv->kauai_fcr);
fcr &= ~(KAUAI_FCR_UATA_RESET_N | KAUAI_FCR_UATA_ENABLE);
writel(fcr, priv->kauai_fcr);
}
/* For PCI, save state and disable DMA. No need to call
* pci_set_power_state(), the HW doesn't do D states that
* way, the platform code will take care of suspending the
* ASIC properly
*/
if (priv->pdev) {
pci_save_state(priv->pdev);
pci_disable_device(priv->pdev);
}
/* Disable the bus on older machines and the cell on kauai */
ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, priv->node,
priv->aapl_bus_id, 0);
return 0;
}
static int pata_macio_do_resume(struct pata_macio_priv *priv)
{
/* Reset and re-enable the HW */
pata_macio_reset_hw(priv, 1);
/* Sanitize drive timings */
pata_macio_apply_timings(priv->host->ports[0], 0);
/* We want our IRQ back ! */
enable_irq(priv->irq);
/* Let the libata core take it from there */
ata_host_resume(priv->host);
return 0;
}
#endif /* CONFIG_PM_SLEEP */
static const struct scsi_host_template pata_macio_sht = {
__ATA_BASE_SHT(DRV_NAME),
.sg_tablesize = MAX_DCMDS,
/* We may not need that strict one */
.dma_boundary = ATA_DMA_BOUNDARY,
/* Not sure what the real max is but we know it's less than 64K, let's
* use 64K minus 256
*/
.max_segment_size = MAX_DBDMA_SEG,
.slave_configure = pata_macio_slave_config,
.sdev_groups = ata_common_sdev_groups,
.can_queue = ATA_DEF_QUEUE,
.tag_alloc_policy = BLK_TAG_ALLOC_RR,
};
static struct ata_port_operations pata_macio_ops = {
.inherits = &ata_bmdma_port_ops,
.freeze = pata_macio_freeze,
.set_piomode = pata_macio_set_timings,
.set_dmamode = pata_macio_set_timings,
.cable_detect = pata_macio_cable_detect,
.sff_dev_select = pata_macio_dev_select,
.qc_prep = pata_macio_qc_prep,
.bmdma_setup = pata_macio_bmdma_setup,
.bmdma_start = pata_macio_bmdma_start,
.bmdma_stop = pata_macio_bmdma_stop,
.bmdma_status = pata_macio_bmdma_status,
.port_start = pata_macio_port_start,
.sff_irq_clear = pata_macio_irq_clear,
};
static void pata_macio_invariants(struct pata_macio_priv *priv)
{
const int *bidp;
/* Identify the type of controller */
if (of_device_is_compatible(priv->node, "shasta-ata")) {
priv->kind = controller_sh_ata6;
priv->timings = pata_macio_shasta_timings;
} else if (of_device_is_compatible(priv->node, "kauai-ata")) {
priv->kind = controller_un_ata6;
priv->timings = pata_macio_kauai_timings;
} else if (of_device_is_compatible(priv->node, "K2-UATA")) {
priv->kind = controller_k2_ata6;
priv->timings = pata_macio_kauai_timings;
} else if (of_device_is_compatible(priv->node, "keylargo-ata")) {
if (of_node_name_eq(priv->node, "ata-4")) {
priv->kind = controller_kl_ata4;
priv->timings = pata_macio_kl66_timings;
} else {
priv->kind = controller_kl_ata3;
priv->timings = pata_macio_kl33_timings;
}
} else if (of_device_is_compatible(priv->node, "heathrow-ata")) {
priv->kind = controller_heathrow;
priv->timings = pata_macio_heathrow_timings;
} else {
priv->kind = controller_ohare;
priv->timings = pata_macio_ohare_timings;
}
/* XXX FIXME --- setup priv->mediabay here */
/* Get Apple bus ID (for clock and ASIC control) */
bidp = of_get_property(priv->node, "AAPL,bus-id", NULL);
priv->aapl_bus_id = bidp ? *bidp : 0;
/* Fixup missing Apple bus ID in case of media-bay */
if (priv->mediabay && !bidp)
priv->aapl_bus_id = 1;
}
static void pata_macio_setup_ios(struct ata_ioports *ioaddr,
void __iomem * base, void __iomem * dma)
{
/* cmd_addr is the base of regs for that port */
ioaddr->cmd_addr = base;
/* taskfile registers */
ioaddr->data_addr = base + (ATA_REG_DATA << 4);
ioaddr->error_addr = base + (ATA_REG_ERR << 4);
ioaddr->feature_addr = base + (ATA_REG_FEATURE << 4);
ioaddr->nsect_addr = base + (ATA_REG_NSECT << 4);
ioaddr->lbal_addr = base + (ATA_REG_LBAL << 4);
ioaddr->lbam_addr = base + (ATA_REG_LBAM << 4);
ioaddr->lbah_addr = base + (ATA_REG_LBAH << 4);
ioaddr->device_addr = base + (ATA_REG_DEVICE << 4);
ioaddr->status_addr = base + (ATA_REG_STATUS << 4);
ioaddr->command_addr = base + (ATA_REG_CMD << 4);
ioaddr->altstatus_addr = base + 0x160;
ioaddr->ctl_addr = base + 0x160;
ioaddr->bmdma_addr = dma;
}
static void pmac_macio_calc_timing_masks(struct pata_macio_priv *priv,
struct ata_port_info *pinfo)
{
int i = 0;
pinfo->pio_mask = 0;
pinfo->mwdma_mask = 0;
pinfo->udma_mask = 0;
while (priv->timings[i].mode > 0) {
unsigned int mask = 1U << (priv->timings[i].mode & 0x0f);
switch(priv->timings[i].mode & 0xf0) {
case 0x00: /* PIO */
pinfo->pio_mask |= (mask >> 8);
break;
case 0x20: /* MWDMA */
pinfo->mwdma_mask |= mask;
break;
case 0x40: /* UDMA */
pinfo->udma_mask |= mask;
break;
}
i++;
}
dev_dbg(priv->dev, "Supported masks: PIO=%x, MWDMA=%x, UDMA=%x\n",
pinfo->pio_mask, pinfo->mwdma_mask, pinfo->udma_mask);
}
static int pata_macio_common_init(struct pata_macio_priv *priv,
resource_size_t tfregs,
resource_size_t dmaregs,
resource_size_t fcregs,
unsigned long irq)
{
struct ata_port_info pinfo;
const struct ata_port_info *ppi[] = { &pinfo, NULL };
void __iomem *dma_regs = NULL;
/* Fill up privates with various invariants collected from the
* device-tree
*/
pata_macio_invariants(priv);
/* Make sure we have sane initial timings in the cache */
pata_macio_default_timings(priv);
/* Allocate libata host for 1 port */
memset(&pinfo, 0, sizeof(struct ata_port_info));
pmac_macio_calc_timing_masks(priv, &pinfo);
pinfo.flags = ATA_FLAG_SLAVE_POSS;
pinfo.port_ops = &pata_macio_ops;
pinfo.private_data = priv;
priv->host = ata_host_alloc_pinfo(priv->dev, ppi, 1);
if (priv->host == NULL) {
dev_err(priv->dev, "Failed to allocate ATA port structure\n");
return -ENOMEM;
}
/* Setup the private data in host too */
priv->host->private_data = priv;
/* Map base registers */
priv->tfregs = devm_ioremap(priv->dev, tfregs, 0x100);
if (priv->tfregs == NULL) {
dev_err(priv->dev, "Failed to map ATA ports\n");
return -ENOMEM;
}
priv->host->iomap = &priv->tfregs;
/* Map DMA regs */
if (dmaregs != 0) {
dma_regs = devm_ioremap(priv->dev, dmaregs,
sizeof(struct dbdma_regs));
if (dma_regs == NULL)
dev_warn(priv->dev, "Failed to map ATA DMA registers\n");
}
/* If chip has local feature control, map those regs too */
if (fcregs != 0) {
priv->kauai_fcr = devm_ioremap(priv->dev, fcregs, 4);
if (priv->kauai_fcr == NULL) {
dev_err(priv->dev, "Failed to map ATA FCR register\n");
return -ENOMEM;
}
}
/* Setup port data structure */
pata_macio_setup_ios(&priv->host->ports[0]->ioaddr,
priv->tfregs, dma_regs);
priv->host->ports[0]->private_data = priv;
/* hard-reset the controller */
pata_macio_reset_hw(priv, 0);
pata_macio_apply_timings(priv->host->ports[0], 0);
/* Enable bus master if necessary */
if (priv->pdev && dma_regs)
pci_set_master(priv->pdev);
dev_info(priv->dev, "Activating pata-macio chipset %s, Apple bus ID %d\n",
macio_ata_names[priv->kind], priv->aapl_bus_id);
/* Start it up */
priv->irq = irq;
return ata_host_activate(priv->host, irq, ata_bmdma_interrupt, 0,
&pata_macio_sht);
}
static int pata_macio_attach(struct macio_dev *mdev,
const struct of_device_id *match)
{
struct pata_macio_priv *priv;
resource_size_t tfregs, dmaregs = 0;
unsigned long irq;
int rc;
/* Check for broken device-trees */
if (macio_resource_count(mdev) == 0) {
dev_err(&mdev->ofdev.dev,
"No addresses for controller\n");
return -ENXIO;
}
/* Enable managed resources */
macio_enable_devres(mdev);
/* Allocate and init private data structure */
priv = devm_kzalloc(&mdev->ofdev.dev,
sizeof(struct pata_macio_priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
priv->node = of_node_get(mdev->ofdev.dev.of_node);
priv->mdev = mdev;
priv->dev = &mdev->ofdev.dev;
/* Request memory resource for taskfile registers */
if (macio_request_resource(mdev, 0, "pata-macio")) {
dev_err(&mdev->ofdev.dev,
"Cannot obtain taskfile resource\n");
return -EBUSY;
}
tfregs = macio_resource_start(mdev, 0);
/* Request resources for DMA registers if any */
if (macio_resource_count(mdev) >= 2) {
if (macio_request_resource(mdev, 1, "pata-macio-dma"))
dev_err(&mdev->ofdev.dev,
"Cannot obtain DMA resource\n");
else
dmaregs = macio_resource_start(mdev, 1);
}
/*
* Fixup missing IRQ for some old implementations with broken
* device-trees.
*
* This is a bit bogus, it should be fixed in the device-tree itself,
* via the existing macio fixups, based on the type of interrupt
* controller in the machine. However, I have no test HW for this case,
* and this trick works well enough on those old machines...
*/
if (macio_irq_count(mdev) == 0) {
dev_warn(&mdev->ofdev.dev,
"No interrupts for controller, using 13\n");
irq = irq_create_mapping(NULL, 13);
} else
irq = macio_irq(mdev, 0);
/* Prevvent media bay callbacks until fully registered */
lock_media_bay(priv->mdev->media_bay);
/* Get register addresses and call common initialization */
rc = pata_macio_common_init(priv,
tfregs, /* Taskfile regs */
dmaregs, /* DBDMA regs */
0, /* Feature control */
irq);
unlock_media_bay(priv->mdev->media_bay);
return rc;
}
static int pata_macio_detach(struct macio_dev *mdev)
{
struct ata_host *host = macio_get_drvdata(mdev);
struct pata_macio_priv *priv = host->private_data;
lock_media_bay(priv->mdev->media_bay);
/* Make sure the mediabay callback doesn't try to access
* dead stuff
*/
priv->host->private_data = NULL;
ata_host_detach(host);
unlock_media_bay(priv->mdev->media_bay);
return 0;
}
#ifdef CONFIG_PM_SLEEP
static int pata_macio_suspend(struct macio_dev *mdev, pm_message_t mesg)
{
struct ata_host *host = macio_get_drvdata(mdev);
return pata_macio_do_suspend(host->private_data, mesg);
}
static int pata_macio_resume(struct macio_dev *mdev)
{
struct ata_host *host = macio_get_drvdata(mdev);
return pata_macio_do_resume(host->private_data);
}
#endif /* CONFIG_PM_SLEEP */
#ifdef CONFIG_PMAC_MEDIABAY
static void pata_macio_mb_event(struct macio_dev* mdev, int mb_state)
{
struct ata_host *host = macio_get_drvdata(mdev);
struct ata_port *ap;
struct ata_eh_info *ehi;
struct ata_device *dev;
unsigned long flags;
if (!host || !host->private_data)
return;
ap = host->ports[0];
spin_lock_irqsave(ap->lock, flags);
ehi = &ap->link.eh_info;
if (mb_state == MB_CD) {
ata_ehi_push_desc(ehi, "mediabay plug");
ata_ehi_hotplugged(ehi);
ata_port_freeze(ap);
} else {
ata_ehi_push_desc(ehi, "mediabay unplug");
ata_for_each_dev(dev, &ap->link, ALL)
dev->flags |= ATA_DFLAG_DETACH;
ata_port_abort(ap);
}
spin_unlock_irqrestore(ap->lock, flags);
}
#endif /* CONFIG_PMAC_MEDIABAY */
static int pata_macio_pci_attach(struct pci_dev *pdev,
const struct pci_device_id *id)
{
struct pata_macio_priv *priv;
struct device_node *np;
resource_size_t rbase;
/* We cannot use a MacIO controller without its OF device node */
np = pci_device_to_OF_node(pdev);
if (np == NULL) {
dev_err(&pdev->dev,
"Cannot find OF device node for controller\n");
return -ENODEV;
}
/* Check that it can be enabled */
if (pcim_enable_device(pdev)) {
dev_err(&pdev->dev,
"Cannot enable controller PCI device\n");
return -ENXIO;
}
/* Allocate and init private data structure */
priv = devm_kzalloc(&pdev->dev,
sizeof(struct pata_macio_priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
priv->node = of_node_get(np);
priv->pdev = pdev;
priv->dev = &pdev->dev;
/* Get MMIO regions */
if (pci_request_regions(pdev, "pata-macio")) {
dev_err(&pdev->dev,
"Cannot obtain PCI resources\n");
return -EBUSY;
}
/* Get register addresses and call common initialization */
rbase = pci_resource_start(pdev, 0);
if (pata_macio_common_init(priv,
rbase + 0x2000, /* Taskfile regs */
rbase + 0x1000, /* DBDMA regs */
rbase, /* Feature control */
pdev->irq))
return -ENXIO;
return 0;
}
static void pata_macio_pci_detach(struct pci_dev *pdev)
{
struct ata_host *host = pci_get_drvdata(pdev);
ata_host_detach(host);
}
#ifdef CONFIG_PM_SLEEP
static int pata_macio_pci_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
struct ata_host *host = pci_get_drvdata(pdev);
return pata_macio_do_suspend(host->private_data, mesg);
}
static int pata_macio_pci_resume(struct pci_dev *pdev)
{
struct ata_host *host = pci_get_drvdata(pdev);
return pata_macio_do_resume(host->private_data);
}
#endif /* CONFIG_PM_SLEEP */
static const struct of_device_id pata_macio_match[] =
{
{ .name = "IDE", },
{ .name = "ATA", },
{ .type = "ide", },
{ .type = "ata", },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, pata_macio_match);
static struct macio_driver pata_macio_driver =
{
.driver = {
.name = "pata-macio",
.owner = THIS_MODULE,
.of_match_table = pata_macio_match,
},
.probe = pata_macio_attach,
.remove = pata_macio_detach,
#ifdef CONFIG_PM_SLEEP
.suspend = pata_macio_suspend,
.resume = pata_macio_resume,
#endif
#ifdef CONFIG_PMAC_MEDIABAY
.mediabay_event = pata_macio_mb_event,
#endif
};
static const struct pci_device_id pata_macio_pci_match[] = {
{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_UNI_N_ATA), 0 },
{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_IPID_ATA100), 0 },
{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_K2_ATA100), 0 },
{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_SH_ATA), 0 },
{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_IPID2_ATA), 0 },
{},
};
static struct pci_driver pata_macio_pci_driver = {
.name = "pata-pci-macio",
.id_table = pata_macio_pci_match,
.probe = pata_macio_pci_attach,
.remove = pata_macio_pci_detach,
#ifdef CONFIG_PM_SLEEP
.suspend = pata_macio_pci_suspend,
.resume = pata_macio_pci_resume,
#endif
.driver = {
.owner = THIS_MODULE,
},
};
MODULE_DEVICE_TABLE(pci, pata_macio_pci_match);
static int __init pata_macio_init(void)
{
int rc;
if (!machine_is(powermac))
return -ENODEV;
rc = pci_register_driver(&pata_macio_pci_driver);
if (rc)
return rc;
rc = macio_register_driver(&pata_macio_driver);
if (rc) {
pci_unregister_driver(&pata_macio_pci_driver);
return rc;
}
return 0;
}
static void __exit pata_macio_exit(void)
{
macio_unregister_driver(&pata_macio_driver);
pci_unregister_driver(&pata_macio_pci_driver);
}
module_init(pata_macio_init);
module_exit(pata_macio_exit);
MODULE_AUTHOR("Benjamin Herrenschmidt");
MODULE_DESCRIPTION("Apple MacIO PATA driver");
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);