/****************************************************************************** * * This file is provided under a dual BSD/GPLv2 license. When using or * redistributing this file, you may do so under either license. * * GPL LICENSE SUMMARY * * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of version 2 of the GNU General Public License as * published by the Free Software Foundation. * * This program is distributed in the hope that it will be useful, but * WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU * General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110, * USA * * The full GNU General Public License is included in this distribution * in the file called LICENSE.GPL. * * Contact Information: * Intel Linux Wireless <ilw@linux.intel.com> * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 * * BSD LICENSE * * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * * Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * * Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * * Neither the name Intel Corporation nor the names of its * contributors may be used to endorse or promote products derived * from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * *****************************************************************************/ #ifndef __il_csr_h__ #define __il_csr_h__ /* * CSR (control and status registers) * * CSR registers are mapped directly into PCI bus space, and are accessible * whenever platform supplies power to device, even when device is in * low power states due to driver-invoked device resets * (e.g. CSR_RESET_REG_FLAG_SW_RESET) or uCode-driven power-saving modes. * * Use _il_wr() and _il_rd() family to access these registers; * these provide simple PCI bus access, without waking up the MAC. * Do not use il_wr() family for these registers; * no need to "grab nic access" via CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ. * The MAC (uCode processor, etc.) does not need to be powered up for accessing * the CSR registers. * * NOTE: Device does need to be awake in order to read this memory * via CSR_EEPROM register */ #define CSR_BASE (0x000) #define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */ #define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */ #define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */ #define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */ #define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack */ #define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */ #define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc */ #define CSR_GP_CNTRL (CSR_BASE+0x024) /* 2nd byte of CSR_INT_COALESCING, not accessible via _il_wr()! */ #define CSR_INT_PERIODIC_REG (CSR_BASE+0x005) /* * Hardware revision info * Bit fields: * 31-8: Reserved * 7-4: Type of device: see CSR_HW_REV_TYPE_xxx definitions * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D * 1-0: "Dash" (-) value, as in A-1, etc. * * NOTE: Revision step affects calculation of CCK txpower for 4965. * NOTE: See also CSR_HW_REV_WA_REG (work-around for bug in 4965). */ #define CSR_HW_REV (CSR_BASE+0x028) /* * EEPROM memory reads * * NOTE: Device must be awake, initialized via apm_ops.init(), * in order to read. */ #define CSR_EEPROM_REG (CSR_BASE+0x02c) #define CSR_EEPROM_GP (CSR_BASE+0x030) #define CSR_GIO_REG (CSR_BASE+0x03C) #define CSR_GP_UCODE_REG (CSR_BASE+0x048) #define CSR_GP_DRIVER_REG (CSR_BASE+0x050) /* * UCODE-DRIVER GP (general purpose) mailbox registers. * SET/CLR registers set/clear bit(s) if "1" is written. */ #define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054) #define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058) #define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c) #define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060) #define CSR_LED_REG (CSR_BASE+0x094) #define CSR_DRAM_INT_TBL_REG (CSR_BASE+0x0A0) /* GIO Chicken Bits (PCI Express bus link power management) */ #define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100) /* Analog phase-lock-loop configuration */ #define CSR_ANA_PLL_CFG (CSR_BASE+0x20c) /* * CSR Hardware Revision Workaround Register. Indicates hardware rev; * "step" determines CCK backoff for txpower calculation. Used for 4965 only. * See also CSR_HW_REV register. * Bit fields: * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step * 1-0: "Dash" (-) value, as in C-1, etc. */ #define CSR_HW_REV_WA_REG (CSR_BASE+0x22C) #define CSR_DBG_HPET_MEM_REG (CSR_BASE+0x240) #define CSR_DBG_LINK_PWR_MGMT_REG (CSR_BASE+0x250) /* Bits for CSR_HW_IF_CONFIG_REG */ #define CSR49_HW_IF_CONFIG_REG_BIT_4965_R (0x00000010) #define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x00000C00) #define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100) #define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200) #define CSR39_HW_IF_CONFIG_REG_BIT_3945_MB (0x00000100) #define CSR39_HW_IF_CONFIG_REG_BIT_3945_MM (0x00000200) #define CSR39_HW_IF_CONFIG_REG_BIT_SKU_MRC (0x00000400) #define CSR39_HW_IF_CONFIG_REG_BIT_BOARD_TYPE (0x00000800) #define CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A (0x00000000) #define CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B (0x00001000) #define CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A (0x00080000) #define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000) #define CSR_HW_IF_CONFIG_REG_BIT_NIC_READY (0x00400000) /* PCI_OWN_SEM */ #define CSR_HW_IF_CONFIG_REG_BIT_NIC_PREPARE_DONE (0x02000000) /* ME_OWN */ #define CSR_HW_IF_CONFIG_REG_PREPARE (0x08000000) /* WAKE_ME */ #define CSR_INT_PERIODIC_DIS (0x00) /* disable periodic int */ #define CSR_INT_PERIODIC_ENA (0xFF) /* 255*32 usec ~ 8 msec */ /* interrupt flags in INTA, set by uCode or hardware (e.g. dma), * acknowledged (reset) by host writing "1" to flagged bits. */ #define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */ #define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */ #define CSR_INT_BIT_RX_PERIODIC (1 << 28) /* Rx periodic */ #define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */ #define CSR_INT_BIT_SCD (1 << 26) /* TXQ pointer advanced */ #define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */ #define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */ #define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */ #define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses, 3945 */ #define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */ #define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */ #define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \ CSR_INT_BIT_HW_ERR | \ CSR_INT_BIT_FH_TX | \ CSR_INT_BIT_SW_ERR | \ CSR_INT_BIT_RF_KILL | \ CSR_INT_BIT_SW_RX | \ CSR_INT_BIT_WAKEUP | \ CSR_INT_BIT_ALIVE) /* interrupt flags in FH (flow handler) (PCI busmaster DMA) */ #define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */ #define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */ #define CSR39_FH_INT_BIT_RX_CHNL2 (1 << 18) /* Rx channel 2 (3945 only) */ #define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */ #define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */ #define CSR39_FH_INT_BIT_TX_CHNL6 (1 << 6) /* Tx channel 6 (3945 only) */ #define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */ #define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */ #define CSR39_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ CSR39_FH_INT_BIT_RX_CHNL2 | \ CSR_FH_INT_BIT_RX_CHNL1 | \ CSR_FH_INT_BIT_RX_CHNL0) #define CSR39_FH_INT_TX_MASK (CSR39_FH_INT_BIT_TX_CHNL6 | \ CSR_FH_INT_BIT_TX_CHNL1 | \ CSR_FH_INT_BIT_TX_CHNL0) #define CSR49_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ CSR_FH_INT_BIT_RX_CHNL1 | \ CSR_FH_INT_BIT_RX_CHNL0) #define CSR49_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \ CSR_FH_INT_BIT_TX_CHNL0) /* GPIO */ #define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200) #define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000) #define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC (0x00000200) /* RESET */ #define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001) #define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002) #define CSR_RESET_REG_FLAG_SW_RESET (0x00000080) #define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100) #define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200) #define CSR_RESET_LINK_PWR_MGMT_DISABLED (0x80000000) /* * GP (general purpose) CONTROL REGISTER * Bit fields: * 27: HW_RF_KILL_SW * Indicates state of (platform's) hardware RF-Kill switch * 26-24: POWER_SAVE_TYPE * Indicates current power-saving mode: * 000 -- No power saving * 001 -- MAC power-down * 010 -- PHY (radio) power-down * 011 -- Error * 9-6: SYS_CONFIG * Indicates current system configuration, reflecting pins on chip * as forced high/low by device circuit board. * 4: GOING_TO_SLEEP * Indicates MAC is entering a power-saving sleep power-down. * Not a good time to access device-internal resources. * 3: MAC_ACCESS_REQ * Host sets this to request and maintain MAC wakeup, to allow host * access to device-internal resources. Host must wait for * MAC_CLOCK_READY (and !GOING_TO_SLEEP) before accessing non-CSR * device registers. * 2: INIT_DONE * Host sets this to put device into fully operational D0 power mode. * Host resets this after SW_RESET to put device into low power mode. * 0: MAC_CLOCK_READY * Indicates MAC (ucode processor, etc.) is powered up and can run. * Internal resources are accessible. * NOTE: This does not indicate that the processor is actually running. * NOTE: This does not indicate that 4965 or 3945 has completed * init or post-power-down restore of internal SRAM memory. * Use CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP as indication that * SRAM is restored and uCode is in normal operation mode. * Later devices (5xxx/6xxx/1xxx) use non-volatile SRAM, and * do not need to save/restore it. * NOTE: After device reset, this bit remains "0" until host sets * INIT_DONE */ #define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001) #define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004) #define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008) #define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010) #define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001) #define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000) #define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000) #define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000) /* EEPROM REG */ #define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001) #define CSR_EEPROM_REG_BIT_CMD (0x00000002) #define CSR_EEPROM_REG_MSK_ADDR (0x0000FFFC) #define CSR_EEPROM_REG_MSK_DATA (0xFFFF0000) /* EEPROM GP */ #define CSR_EEPROM_GP_VALID_MSK (0x00000007) /* signature */ #define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180) #define CSR_EEPROM_GP_GOOD_SIG_EEP_LESS_THAN_4K (0x00000002) #define CSR_EEPROM_GP_GOOD_SIG_EEP_MORE_THAN_4K (0x00000004) /* GP REG */ #define CSR_GP_REG_POWER_SAVE_STATUS_MSK (0x03000000) /* bit 24/25 */ #define CSR_GP_REG_NO_POWER_SAVE (0x00000000) #define CSR_GP_REG_MAC_POWER_SAVE (0x01000000) #define CSR_GP_REG_PHY_POWER_SAVE (0x02000000) #define CSR_GP_REG_POWER_SAVE_ERROR (0x03000000) /* CSR GIO */ #define CSR_GIO_REG_VAL_L0S_ENABLED (0x00000002) /* * UCODE-DRIVER GP (general purpose) mailbox register 1 * Host driver and uCode write and/or read this register to communicate with * each other. * Bit fields: * 4: UCODE_DISABLE * Host sets this to request permanent halt of uCode, same as * sending CARD_STATE command with "halt" bit set. * 3: CT_KILL_EXIT * Host sets this to request exit from CT_KILL state, i.e. host thinks * device temperature is low enough to continue normal operation. * 2: CMD_BLOCKED * Host sets this during RF KILL power-down sequence (HW, SW, CT KILL) * to release uCode to clear all Tx and command queues, enter * unassociated mode, and power down. * NOTE: Some devices also use HBUS_TARG_MBX_C register for this bit. * 1: SW_BIT_RFKILL * Host sets this when issuing CARD_STATE command to request * device sleep. * 0: MAC_SLEEP * uCode sets this when preparing a power-saving power-down. * uCode resets this when power-up is complete and SRAM is sane. * NOTE: 3945/4965 saves internal SRAM data to host when powering down, * and must restore this data after powering back up. * MAC_SLEEP is the best indication that restore is complete. * Later devices (5xxx/6xxx/1xxx) use non-volatile SRAM, and * do not need to save/restore it. */ #define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001) #define CSR_UCODE_SW_BIT_RFKILL (0x00000002) #define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004) #define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008) /* GIO Chicken Bits (PCI Express bus link power management) */ #define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000) #define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000) /* LED */ #define CSR_LED_BSM_CTRL_MSK (0xFFFFFFDF) #define CSR_LED_REG_TRUN_ON (0x78) #define CSR_LED_REG_TRUN_OFF (0x38) /* ANA_PLL */ #define CSR39_ANA_PLL_CFG_VAL (0x01000000) /* HPET MEM debug */ #define CSR_DBG_HPET_MEM_REG_VAL (0xFFFF0000) /* DRAM INT TBL */ #define CSR_DRAM_INT_TBL_ENABLE (1 << 31) #define CSR_DRAM_INIT_TBL_WRAP_CHECK (1 << 27) /* * HBUS (Host-side Bus) * * HBUS registers are mapped directly into PCI bus space, but are used * to indirectly access device's internal memory or registers that * may be powered-down. * * Use il_wr()/il_rd() family * for these registers; * host must "grab nic access" via CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ * to make sure the MAC (uCode processor, etc.) is powered up for accessing * internal resources. * * Do not use _il_wr()/_il_rd() family to access these registers; * these provide only simple PCI bus access, without waking up the MAC. */ #define HBUS_BASE (0x400) /* * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM * structures, error log, event log, verifying uCode load). * First write to address register, then read from or write to data register * to complete the job. Once the address register is set up, accesses to * data registers auto-increment the address by one dword. * Bit usage for address registers (read or write): * 0-31: memory address within device */ #define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c) #define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010) #define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018) #define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c) /* Mailbox C, used as workaround alternative to CSR_UCODE_DRV_GP1 mailbox */ #define HBUS_TARG_MBX_C (HBUS_BASE+0x030) #define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004) /* * Registers for accessing device's internal peripheral registers * (e.g. SCD, BSM, etc.). First write to address register, * then read from or write to data register to complete the job. * Bit usage for address registers (read or write): * 0-15: register address (offset) within device * 24-25: (# bytes - 1) to read or write (e.g. 3 for dword) */ #define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044) #define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048) #define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c) #define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050) /* * Per-Tx-queue write pointer (idx, really!) * Indicates idx to next TFD that driver will fill (1 past latest filled). * Bit usage: * 0-7: queue write idx * 11-8: queue selector */ #define HBUS_TARG_WRPTR (HBUS_BASE+0x060) #endif /* !__il_csr_h__ */