// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Device Tree for the TVK1281618 R2 user interface board (UIB)
*/
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/input/input.h>
/ {
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
pinctrl-names = "default";
pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;
button@139 {
/* Proximity sensor */
gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
linux,code = <11>; /* SW_FRONT_PROXIMITY */
label = "SFH7741 Proximity Sensor";
};
button@145 {
/* Hall sensor */
gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
linux,code = <0>; /* SW_LID */
label = "HED54XXU11 Hall Effect Sensor";
};
};
soc {
i2c@80004000 {
tc35893@44 {
compatible = "toshiba,tc35893";
reg = <0x44>;
interrupt-parent = <&gpio6>;
interrupts = <26 IRQ_TYPE_EDGE_RISING>;
pinctrl-names = "default";
pinctrl-0 = <&tc35893_tvk_mode>;
interrupt-controller;
#interrupt-cells = <1>;
status = "disabled";
tc3589x_gpio {
compatible = "toshiba,tc3589x-gpio";
interrupts = <0>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
};
tc3589x_keypad {
compatible = "toshiba,tc3589x-keypad";
interrupts = <6>;
debounce-delay-ms = <4>;
keypad,num-columns = <8>;
keypad,num-rows = <8>;
linux,no-autorepeat;
wakeup-source;
linux,keymap = <MATRIX_KEY(3, 1, KEY_END)>,
<MATRIX_KEY(4, 1, KEY_HOME)>,
<MATRIX_KEY(6, 4, KEY_VOLUMEDOWN)>,
<MATRIX_KEY(4, 2, KEY_EMAIL)>,
<MATRIX_KEY(3, 3, KEY_RIGHT)>,
<MATRIX_KEY(2, 5, KEY_BACKSPACE)>,
<MATRIX_KEY(6, 7, KEY_MENU)>,
<MATRIX_KEY(5, 0, KEY_ENTER)>,
<MATRIX_KEY(4, 3, KEY_0)>,
<MATRIX_KEY(3, 4, KEY_DOT)>,
<MATRIX_KEY(5, 2, KEY_UP)>,
<MATRIX_KEY(3, 5, KEY_DOWN)>,
<MATRIX_KEY(4, 5, KEY_SEND)>,
<MATRIX_KEY(0, 5, KEY_BACK)>,
<MATRIX_KEY(6, 2, KEY_VOLUMEUP)>,
<MATRIX_KEY(1, 3, KEY_SPACE)>,
<MATRIX_KEY(7, 6, KEY_LEFT)>,
<MATRIX_KEY(5, 5, KEY_SEARCH)>;
};
};
};
i2c@80128000 {
accelerometer@18 {
/* Accelerometer */
compatible = "st,lsm303dlh-accel";
st,drdy-int-pin = <1>;
drive-open-drain;
reg = <0x18>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&accel_tvk_mode>;
/*
* These interrupts cannot be used: the other component
* ST-Micro L3D4200D gyro that is connected to the same lines
* cannot set its DRDY line to open drain, so it cannot be
* shared with other peripherals. The should be defined for
* the falling edge if they could be wired together.
*
* interrupts-extended =
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
*/
mount-matrix = "0", "1", "0",
"1", "0", "0",
"0", "0", "-1";
};
magnetometer@1e {
/* Magnetometer */
compatible = "st,lsm303dlh-magn";
reg = <0x1e>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
/*
* These interrupts cannot be used: the other component
* ST-Micro L3D4200D gyro that is connected to the same lines
* cannot set its DRDY line to open drain, so it cannot be
* shared with other peripherals. The should be defined for
* the falling edge if they could be wired together.
*
* interrupts-extended =
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
*/
};
accelerometer@1c {
/* Accelerometer */
compatible = "st,lis331dl-accel";
st,drdy-int-pin = <1>;
reg = <0x1c>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&accel_tvk_mode>;
interrupt-parent = <&gpio2>;
/* INT2 would need to be open drain */
interrupts = <18 IRQ_TYPE_EDGE_RISING>,
<19 IRQ_TYPE_EDGE_RISING>;
mount-matrix = "0", "-1", "0",
"-1", "0", "0",
"0", "0", "-1";
};
magnetometer@f {
/* Magnetometer */
compatible = "asahi-kasei,ak8974";
reg = <0x0f>;
avdd-supply = <&ab8500_ldo_aux1_reg>;
dvdd-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&gyro_magn_tvk_mode>;
/*
* These interrupts cannot be used: the other component
* ST-Micro L3D4200D gyro that is connected to the same lines
* cannot set its DRDY line to open drain, so it cannot be
* shared with other peripherals. The should be defined for
* the falling edge if they could be wired together.
*
* interrupts-extended =
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
* <&gpio0 31 IRQ_TYPE_EDGE_FALLING>;
*/
};
gyroscope@68 {
/* Gyroscope */
compatible = "st,l3g4200d-gyro";
st,drdy-int-pin = <2>;
reg = <0x68>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&gyro_magn_tvk_mode>;
interrupts-extended =
<&gpio1 0 IRQ_TYPE_EDGE_RISING>,
<&gpio0 31 IRQ_TYPE_EDGE_RISING>;
};
pressure@5c {
/* Barometer/pressure sensor */
compatible = "st,lps001wp-press";
reg = <0x5c>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
};
};
i2c@80110000 {
synaptics@4b {
/* Synaptics RMI4 TM1217 touchscreen */
compatible = "syna,rmi4-i2c";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x4b>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&synaptics_tvk_mode>;
interrupt-parent = <&gpio2>;
interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
rmi4-f01@1 {
reg = <0x1>;
syna,nosleep = <1>;
};
rmi4-f11@11 {
reg = <0x11>;
syna,sensor-type = <1>;
/* This is a landscape display */
touchscreen-swapped-x-y;
};
};
};
mcde@a0350000 {
status = "okay";
dsi@a0351000 {
panel {
compatible = "samsung,s6d16d0";
reg = <0>;
vdd1-supply = <&ab8500_ldo_aux1_reg>;
reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
};
};
};
pinctrl {
prox {
prox_tvk_mode: prox_tvk {
tvk_cfg {
pins = "GPIO217_AH12";
ste,config = <&gpio_in_pu>;
};
};
};
hall {
hall_tvk_mode: hall_tvk {
tvk_cfg {
pins = "GPIO145_C13";
ste,config = <&gpio_in_pu>;
};
};
};
tc35893 {
/* IRQ from the TC35893 */
tc35893_tvk_mode: tc35893_tvk {
tvk_cfg {
pins = "GPIO218_AH11";
ste,config = <&gpio_in_pu>;
};
};
};
accelerometer {
accel_tvk_mode: accel_tvk {
/* Accelerometer interrupt lines 1 & 2 */
tvk_cfg {
pins = "GPIO82_C1", "GPIO83_D3";
ste,config = <&gpio_in_pd>;
};
};
};
gyroscope {
/*
* These lines are shared between Gyroscope l3g400dh
* and AK8974 magnetometer.
*/
gyro_magn_tvk_mode: gyro_magn_tvk {
/* GPIO 31 used for INT pull down the line */
tvk_cfg1 {
pins = "GPIO31_V3";
ste,config = <&gpio_in_pd>;
};
/* GPIO 32 used for DRDY, pull this down */
tvk_cfg2 {
pins = "GPIO32_V2";
ste,config = <&gpio_in_pd>;
};
};
};
synaptics {
synaptics_tvk_mode: synaptics_tvk {
/* Touchscreen uses GPIO 84 */
tvk_cfg1 {
pins = "GPIO84_C2";
ste,config = <&gpio_in_pu>;
};
};
};
};
};
};