// SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd * Copyright (c) 2019 Radxa Limited * Copyright (c) 2019 Amarula Solutions(India) */ #include <dt-bindings/pwm/pwm.h> / { clkin_gmac: external-gmac-clock { compatible = "fixed-clock"; clock-frequency = <125000000>; clock-output-names = "clkin_gmac"; #clock-cells = <0>; }; sdio_pwrseq: sdio-pwrseq { compatible = "mmc-pwrseq-simple"; clocks = <&hym8563>; clock-names = "ext_clock"; pinctrl-names = "default"; pinctrl-0 = <&wifi_enable_h>; }; vcc12v_dcin: vcc12v-dcin-regulator { compatible = "regulator-fixed"; regulator-name = "vcc12v_dcin"; regulator-always-on; regulator-boot-on; regulator-min-microvolt = <12000000>; regulator-max-microvolt = <12000000>; }; vcc5v0_sys: vcc5v0-sys-regulator { compatible = "regulator-fixed"; regulator-name = "vcc5v0_sys"; regulator-always-on; regulator-boot-on; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; vin-supply = <&vcc12v_dcin>; }; vbus_host: vbus-host { compatible = "regulator-fixed"; pinctrl-names = "default"; pinctrl-0 = <&usb1_en_oc>; regulator-name = "vbus_host"; /* HOST-5V */ regulator-always-on; vin-supply = <&vcc5v0_sys>; }; vbus_typec: vbus-typec { compatible = "regulator-fixed"; pinctrl-names = "default"; pinctrl-0 = <&usb0_en_oc>; regulator-name = "vbus_typec"; regulator-always-on; vin-supply = <&vcc5v0_sys>; }; }; &gmac { assigned-clock-parents = <&clkin_gmac>; clock_in_out = "input"; phy-mode = "rgmii"; pinctrl-names = "default"; pinctrl-0 = <&rgmii_pins>; snps,reset-active-low; snps,reset-delays-us = <0 10000 50000>; tx_delay = <0x28>; rx_delay = <0x11>; status = "okay"; }; &hdmi { status = "okay"; }; &pwm0 { status = "okay"; }; &pwm2 { status = "okay"; }; &sdio0 { bus-width = <4>; cap-sd-highspeed; cap-sdio-irq; keep-power-in-suspend; mmc-pwrseq = <&sdio_pwrseq>; non-removable; pinctrl-names = "default"; pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>; sd-uhs-sdr104; status = "okay"; }; &sdmmc { bus-width = <4>; cap-mmc-highspeed; cap-sd-highspeed; disable-wp; vqmmc-supply = <&vccio_sd>; pinctrl-names = "default"; pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; status = "okay"; }; &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_xfer &uart0_cts>; status = "okay"; }; &uart2 { status = "okay"; }; &vopb { status = "okay"; }; &vopb_mmu { status = "okay"; }; &vopl { status = "okay"; }; &vopl_mmu { status = "okay"; };