// SPDX-License-Identifier: GPL-2.0
#include "qcom-msm8974.dtsi"
#include "qcom-pm8841.dtsi"
#include "qcom-pm8941.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
/ {
aliases {
serial0 = &blsp1_uart2;
};
chosen {
stdout-path = "serial0:115200n8";
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&gpio_keys_pin_a>;
key-volume-down {
label = "volume_down";
gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
linux,input-type = <1>;
linux,code = <KEY_VOLUMEDOWN>;
};
key-camera-snapshot {
label = "camera_snapshot";
gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
linux,input-type = <1>;
linux,code = <KEY_CAMERA>;
};
key-camera-focus {
label = "camera_focus";
gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
linux,input-type = <1>;
linux,code = <KEY_CAMERA_FOCUS>;
};
key-volume-up {
label = "volume_up";
gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
linux,input-type = <1>;
linux,code = <KEY_VOLUMEUP>;
};
};
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
ramoops@3e8e0000 {
compatible = "ramoops";
reg = <0x3e8e0000 0x200000>;
console-size = <0x100000>;
record-size = <0x10000>;
ftrace-size = <0x10000>;
pmsg-size = <0x80000>;
};
};
};
&blsp1_i2c2 {
status = "okay";
clock-frequency = <355000>;
synaptics@2c {
compatible = "syna,rmi4-i2c";
reg = <0x2c>;
interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
#address-cells = <1>;
#size-cells = <0>;
vdd-supply = <&pm8941_l22>;
vio-supply = <&pm8941_lvs3>;
pinctrl-names = "default";
pinctrl-0 = <&ts_int_pin>;
syna,startup-delay-ms = <10>;
rmi4-f01@1 {
reg = <0x1>;
syna,nosleep-mode = <1>;
};
rmi4-f11@11 {
reg = <0x11>;
touchscreen-inverted-x;
syna,sensor-type = <1>;
};
};
};
&blsp1_i2c6 {
status = "okay";
clock-frequency = <355000>;
nfc@28 {
compatible = "nxp,pn544-i2c";
reg = <0x28>;
interrupt-parent = <&tlmm>;
interrupts = <59 IRQ_TYPE_EDGE_RISING>;
enable-gpios = <&pm8941_gpios 23 GPIO_ACTIVE_HIGH>;
firmware-gpios = <&tlmm 77 GPIO_ACTIVE_HIGH>;
};
};
&blsp1_uart2 {
status = "okay";
};
&blsp2_dma {
qcom,controlled-remotely;
};
&blsp2_i2c5 {
status = "okay";
clock-frequency = <355000>;
/* sii8334 MHL HDMI bridge */
};
&pm8941_coincell {
status = "okay";
qcom,rset-ohms = <2100>;
qcom,vset-millivolts = <3000>;
};
&pm8941_gpios {
gpio_keys_pin_a: gpio-keys-active-state {
pins = "gpio2", "gpio3", "gpio4", "gpio5";
function = "normal";
bias-pull-up;
power-source = <PM8941_GPIO_S3>;
};
};
&pm8941_lpg {
status = "okay";
qcom,power-source = <1>;
multi-led {
color = <LED_COLOR_ID_RGB>;
function = LED_FUNCTION_STATUS;
#address-cells = <1>;
#size-cells = <0>;
led@5 {
reg = <5>;
color = <LED_COLOR_ID_BLUE>;
};
led@6 {
reg = <6>;
color = <LED_COLOR_ID_GREEN>;
};
led@7 {
reg = <7>;
color = <LED_COLOR_ID_RED>;
};
};
};
&pm8941_wled {
status = "okay";
qcom,cs-out;
qcom,current-limit = <20>;
qcom,current-boost-limit = <805>;
qcom,switching-freq = <1600>;
qcom,ovp = <29>;
qcom,num-strings = <2>;
};
&remoteproc_adsp {
cx-supply = <&pm8841_s2>;
};
&remoteproc_mss {
cx-supply = <&pm8841_s2>;
mss-supply = <&pm8841_s3>;
mx-supply = <&pm8841_s1>;
pll-supply = <&pm8941_l12>;
};
&rpm_requests {
regulators-0 {
compatible = "qcom,rpm-pm8841-regulators";
pm8841_s1: s1 {
regulator-min-microvolt = <675000>;
regulator-max-microvolt = <1050000>;
};
pm8841_s2: s2 {
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1050000>;
};
pm8841_s3: s3 {
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1050000>;
};
pm8841_s4: s4 {
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1050000>;
};
};
regulators-1 {
compatible = "qcom,rpm-pm8941-regulators";
vdd_l1_l3-supply = <&pm8941_s1>;
vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
vdd_l4_l11-supply = <&pm8941_s1>;
vdd_l5_l7-supply = <&pm8941_s2>;
vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
vdd_l21-supply = <&vreg_boost>;
pm8941_s1: s1 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
regulator-always-on;
regulator-boot-on;
};
pm8941_s2: s2 {
regulator-min-microvolt = <2150000>;
regulator-max-microvolt = <2150000>;
regulator-boot-on;
};
pm8941_s3: s3 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
pm8941_s4: s4 {
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
pm8941_l1: l1 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
regulator-always-on;
regulator-boot-on;
};
pm8941_l2: l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
pm8941_l3: l3 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
pm8941_l4: l4 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
};
pm8941_l5: l5 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8941_l6: l6 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
};
pm8941_l7: l7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
};
pm8941_l8: l8 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8941_l9: l9 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
};
pm8941_l11: l11 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1350000>;
};
pm8941_l12: l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
pm8941_l13: l13 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
regulator-boot-on;
};
pm8941_l14: l14 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8941_l15: l15 {
regulator-min-microvolt = <2050000>;
regulator-max-microvolt = <2050000>;
};
pm8941_l16: l16 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
};
pm8941_l17: l17 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
};
pm8941_l18: l18 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
};
pm8941_l19: l19 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
pm8941_l20: l20 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
regulator-system-load = <200000>;
regulator-allow-set-load;
regulator-boot-on;
};
pm8941_l21: l21 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
regulator-boot-on;
};
pm8941_l22: l22 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
pm8941_l23: l23 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
};
pm8941_l24: l24 {
regulator-min-microvolt = <3075000>;
regulator-max-microvolt = <3075000>;
regulator-boot-on;
};
pm8941_lvs3: lvs3 {};
};
};
&sdhc_1 {
status = "okay";
vmmc-supply = <&pm8941_l20>;
vqmmc-supply = <&pm8941_s3>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc1_on>;
pinctrl-1 = <&sdc1_off>;
};
&sdhc_2 {
status = "okay";
vmmc-supply = <&pm8941_l21>;
vqmmc-supply = <&pm8941_l13>;
cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc2_on>;
pinctrl-1 = <&sdc2_off>;
};
&smbb {
qcom,fast-charge-safe-current = <1500000>;
qcom,fast-charge-current-limit = <1500000>;
qcom,dc-current-limit = <1800000>;
qcom,fast-charge-safe-voltage = <4400000>;
qcom,fast-charge-high-threshold-voltage = <4350000>;
qcom,fast-charge-low-threshold-voltage = <3400000>;
qcom,auto-recharge-threshold-voltage = <4200000>;
qcom,minimum-input-voltage = <4300000>;
};
&tlmm {
ts_int_pin: touch-int-state {
pins = "gpio61";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
sdc1_on: sdc1-on-state {
clk-pins {
pins = "sdc1_clk";
drive-strength = <16>;
bias-disable;
};
cmd-data-pins {
pins = "sdc1_cmd", "sdc1_data";
drive-strength = <10>;
bias-pull-up;
};
};
sdc2_on: sdc-on-state {
clk-pins {
pins = "sdc2_clk";
drive-strength = <10>;
bias-disable;
};
cmd-data-pins {
pins = "sdc2_cmd", "sdc2_data";
drive-strength = <6>;
bias-pull-up;
};
cd-pins {
pins = "gpio62";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
};
};
&usb {
status = "okay";
phys = <&usb_hs1_phy>;
phy-select = <&tcsr 0xb000 0>;
extcon = <&smbb>, <&usb_id>;
vbus-supply = <&chg_otg>;
hnp-disable;
srp-disable;
adp-disable;
};
&usb_hs1_phy {
status = "okay";
v1p8-supply = <&pm8941_l6>;
v3p3-supply = <&pm8941_l24>;
extcon = <&smbb>;
qcom,init-seq = /bits/ 8 <0x1 0x64>;
};