# SPDX-License-Identifier: GPL-2.0
# Makefile for nolibc tests
include ../../../scripts/Makefile.include
# We need this for the "cc-option" macro.
include ../../../build/Build.include
# we're in ".../tools/testing/selftests/nolibc"
ifeq ($(srctree),)
srctree := $(patsubst %/tools/testing/selftests/,%,$(dir $(CURDIR)))
endif
ifeq ($(ARCH),)
include $(srctree)/scripts/subarch.include
ARCH = $(SUBARCH)
endif
# XARCH extends the kernel's ARCH with a few variants of the same
# architecture that only differ by the configuration, the toolchain
# and the Qemu program used. It is copied as-is into ARCH except for
# a few specific values which are mapped like this:
#
# XARCH | ARCH | config
# -------------|-----------|-------------------------
# ppc | powerpc | 32 bits
# ppc64 | powerpc | 64 bits big endian
# ppc64le | powerpc | 64 bits little endian
#
# It is recommended to only use XARCH, though it does not harm if
# ARCH is already set. For simplicity, ARCH is sufficient for all
# architectures where both are equal.
# configure default variants for target kernel supported architectures
XARCH_powerpc = ppc
XARCH = $(or $(XARCH_$(ARCH)),$(ARCH))
# map from user input variants to their kernel supported architectures
ARCH_ppc = powerpc
ARCH_ppc64 = powerpc
ARCH_ppc64le = powerpc
ARCH := $(or $(ARCH_$(XARCH)),$(XARCH))
# kernel image names by architecture
IMAGE_i386 = arch/x86/boot/bzImage
IMAGE_x86_64 = arch/x86/boot/bzImage
IMAGE_x86 = arch/x86/boot/bzImage
IMAGE_arm64 = arch/arm64/boot/Image
IMAGE_arm = arch/arm/boot/zImage
IMAGE_mips = vmlinuz
IMAGE_ppc = vmlinux
IMAGE_ppc64 = vmlinux
IMAGE_ppc64le = arch/powerpc/boot/zImage
IMAGE_riscv = arch/riscv/boot/Image
IMAGE_s390 = arch/s390/boot/bzImage
IMAGE_loongarch = arch/loongarch/boot/vmlinuz.efi
IMAGE = $(IMAGE_$(XARCH))
IMAGE_NAME = $(notdir $(IMAGE))
# default kernel configurations that appear to be usable
DEFCONFIG_i386 = defconfig
DEFCONFIG_x86_64 = defconfig
DEFCONFIG_x86 = defconfig
DEFCONFIG_arm64 = defconfig
DEFCONFIG_arm = multi_v7_defconfig
DEFCONFIG_mips = malta_defconfig
DEFCONFIG_ppc = pmac32_defconfig
DEFCONFIG_ppc64 = powernv_be_defconfig
DEFCONFIG_ppc64le = powernv_defconfig
DEFCONFIG_riscv = defconfig
DEFCONFIG_s390 = defconfig
DEFCONFIG_loongarch = defconfig
DEFCONFIG = $(DEFCONFIG_$(XARCH))
# optional tests to run (default = all)
TEST =
# QEMU_ARCH: arch names used by qemu
QEMU_ARCH_i386 = i386
QEMU_ARCH_x86_64 = x86_64
QEMU_ARCH_x86 = x86_64
QEMU_ARCH_arm64 = aarch64
QEMU_ARCH_arm = arm
QEMU_ARCH_mips = mipsel # works with malta_defconfig
QEMU_ARCH_ppc = ppc
QEMU_ARCH_ppc64 = ppc64
QEMU_ARCH_ppc64le = ppc64le
QEMU_ARCH_riscv = riscv64
QEMU_ARCH_s390 = s390x
QEMU_ARCH_loongarch = loongarch64
QEMU_ARCH = $(QEMU_ARCH_$(XARCH))
# QEMU_ARGS : some arch-specific args to pass to qemu
QEMU_ARGS_i386 = -M pc -append "console=ttyS0,9600 i8042.noaux panic=-1 $(TEST:%=NOLIBC_TEST=%)"
QEMU_ARGS_x86_64 = -M pc -append "console=ttyS0,9600 i8042.noaux panic=-1 $(TEST:%=NOLIBC_TEST=%)"
QEMU_ARGS_x86 = -M pc -append "console=ttyS0,9600 i8042.noaux panic=-1 $(TEST:%=NOLIBC_TEST=%)"
QEMU_ARGS_arm64 = -M virt -cpu cortex-a53 -append "panic=-1 $(TEST:%=NOLIBC_TEST=%)"
QEMU_ARGS_arm = -M virt -append "panic=-1 $(TEST:%=NOLIBC_TEST=%)"
QEMU_ARGS_mips = -M malta -append "panic=-1 $(TEST:%=NOLIBC_TEST=%)"
QEMU_ARGS_ppc = -M g3beige -append "console=ttyS0 panic=-1 $(TEST:%=NOLIBC_TEST=%)"
QEMU_ARGS_ppc64 = -M powernv -append "console=hvc0 panic=-1 $(TEST:%=NOLIBC_TEST=%)"
QEMU_ARGS_ppc64le = -M powernv -append "console=hvc0 panic=-1 $(TEST:%=NOLIBC_TEST=%)"
QEMU_ARGS_riscv = -M virt -append "console=ttyS0 panic=-1 $(TEST:%=NOLIBC_TEST=%)"
QEMU_ARGS_s390 = -M s390-ccw-virtio -m 1G -append "console=ttyS0 panic=-1 $(TEST:%=NOLIBC_TEST=%)"
QEMU_ARGS_loongarch = -M virt -append "console=ttyS0,115200 panic=-1 $(TEST:%=NOLIBC_TEST=%)"
QEMU_ARGS = $(QEMU_ARGS_$(XARCH)) $(QEMU_ARGS_EXTRA)
# OUTPUT is only set when run from the main makefile, otherwise
# it defaults to this nolibc directory.
OUTPUT ?= $(CURDIR)/
ifeq ($(V),1)
Q=
else
Q=@
endif
CFLAGS_ppc = -m32 -mbig-endian -mno-vsx $(call cc-option,-mmultiple)
CFLAGS_ppc64 = -m64 -mbig-endian -mno-vsx $(call cc-option,-mmultiple)
CFLAGS_ppc64le = -m64 -mlittle-endian -mno-vsx $(call cc-option,-mabi=elfv2)
CFLAGS_s390 = -m64
CFLAGS_mips = -EL
CFLAGS_STACKPROTECTOR ?= $(call cc-option,-mstack-protector-guard=global $(call cc-option,-fstack-protector-all))
CFLAGS ?= -Os -fno-ident -fno-asynchronous-unwind-tables -std=c89 -W -Wall -Wextra \
$(call cc-option,-fno-stack-protector) \
$(CFLAGS_$(XARCH)) $(CFLAGS_STACKPROTECTOR)
LDFLAGS :=
REPORT ?= awk '/\[OK\][\r]*$$/{p++} /\[FAIL\][\r]*$$/{if (!f) printf("\n"); f++; print;} /\[SKIPPED\][\r]*$$/{s++} \
END{ printf("\n%3d test(s): %3d passed, %3d skipped, %3d failed => status: ", p+s+f, p, s, f); \
if (f) printf("failure\n"); else if (s) printf("warning\n"); else printf("success\n");; \
printf("\nSee all results in %s\n", ARGV[1]); }'
help:
@echo "Supported targets under selftests/nolibc:"
@echo " all call the \"run\" target below"
@echo " help this help"
@echo " sysroot create the nolibc sysroot here (uses \$$ARCH)"
@echo " nolibc-test build the executable (uses \$$CC and \$$CROSS_COMPILE)"
@echo " libc-test build an executable using the compiler's default libc instead"
@echo " run-user runs the executable under QEMU (uses \$$XARCH, \$$TEST)"
@echo " initramfs prepare the initramfs with nolibc-test"
@echo " defconfig create a fresh new default config (uses \$$XARCH)"
@echo " kernel (re)build the kernel with the initramfs (uses \$$XARCH)"
@echo " run runs the kernel in QEMU after building it (uses \$$XARCH, \$$TEST)"
@echo " rerun runs a previously prebuilt kernel in QEMU (uses \$$XARCH, \$$TEST)"
@echo " clean clean the sysroot, initramfs, build and output files"
@echo ""
@echo "The output file is \"run.out\". Test ranges may be passed using \$$TEST."
@echo ""
@echo "Currently using the following variables:"
@echo " ARCH = $(ARCH)"
@echo " XARCH = $(XARCH)"
@echo " CROSS_COMPILE = $(CROSS_COMPILE)"
@echo " CC = $(CC)"
@echo " OUTPUT = $(OUTPUT)"
@echo " TEST = $(TEST)"
@echo " QEMU_ARCH = $(if $(QEMU_ARCH),$(QEMU_ARCH),UNKNOWN_ARCH) [determined from \$$XARCH]"
@echo " IMAGE_NAME = $(if $(IMAGE_NAME),$(IMAGE_NAME),UNKNOWN_ARCH) [determined from \$$XARCH]"
@echo ""
all: run
sysroot: sysroot/$(ARCH)/include
sysroot/$(ARCH)/include:
$(Q)rm -rf sysroot/$(ARCH) sysroot/sysroot
$(QUIET_MKDIR)mkdir -p sysroot
$(Q)$(MAKE) -C ../../../include/nolibc ARCH=$(ARCH) OUTPUT=$(CURDIR)/sysroot/ headers_standalone
$(Q)mv sysroot/sysroot sysroot/$(ARCH)
ifneq ($(NOLIBC_SYSROOT),0)
nolibc-test: nolibc-test.c sysroot/$(ARCH)/include
$(QUIET_CC)$(CC) $(CFLAGS) $(LDFLAGS) -o $@ \
-nostdlib -static -Isysroot/$(ARCH)/include $< -lgcc
else
nolibc-test: nolibc-test.c
$(QUIET_CC)$(CC) $(CFLAGS) $(LDFLAGS) -o $@ \
-nostdlib -static -include ../../../include/nolibc/nolibc.h $< -lgcc
endif
libc-test: nolibc-test.c
$(QUIET_CC)$(HOSTCC) -o $@ $<
# local libc-test
run-libc-test: libc-test
$(Q)./libc-test > "$(CURDIR)/run.out" || :
$(Q)$(REPORT) $(CURDIR)/run.out
# local nolibc-test
run-nolibc-test: nolibc-test
$(Q)./nolibc-test > "$(CURDIR)/run.out" || :
$(Q)$(REPORT) $(CURDIR)/run.out
# qemu user-land test
run-user: nolibc-test
$(Q)qemu-$(QEMU_ARCH) ./nolibc-test > "$(CURDIR)/run.out" || :
$(Q)$(REPORT) $(CURDIR)/run.out
initramfs: nolibc-test
$(QUIET_MKDIR)mkdir -p initramfs
$(call QUIET_INSTALL, initramfs/init)
$(Q)cp nolibc-test initramfs/init
defconfig:
$(Q)$(MAKE) -C $(srctree) ARCH=$(ARCH) CC=$(CC) CROSS_COMPILE=$(CROSS_COMPILE) mrproper $(DEFCONFIG) prepare
kernel: initramfs
$(Q)$(MAKE) -C $(srctree) ARCH=$(ARCH) CC=$(CC) CROSS_COMPILE=$(CROSS_COMPILE) $(IMAGE_NAME) CONFIG_INITRAMFS_SOURCE=$(CURDIR)/initramfs
# run the tests after building the kernel
run: kernel
$(Q)qemu-system-$(QEMU_ARCH) -display none -no-reboot -kernel "$(srctree)/$(IMAGE)" -serial stdio $(QEMU_ARGS) > "$(CURDIR)/run.out"
$(Q)$(REPORT) $(CURDIR)/run.out
# re-run the tests from an existing kernel
rerun:
$(Q)qemu-system-$(QEMU_ARCH) -display none -no-reboot -kernel "$(srctree)/$(IMAGE)" -serial stdio $(QEMU_ARGS) > "$(CURDIR)/run.out"
$(Q)$(REPORT) $(CURDIR)/run.out
# report with existing test log
report:
$(Q)$(REPORT) $(CURDIR)/run.out
clean:
$(call QUIET_CLEAN, sysroot)
$(Q)rm -rf sysroot
$(call QUIET_CLEAN, nolibc-test)
$(Q)rm -f nolibc-test
$(call QUIET_CLEAN, libc-test)
$(Q)rm -f libc-test
$(call QUIET_CLEAN, initramfs)
$(Q)rm -rf initramfs
$(call QUIET_CLEAN, run.out)
$(Q)rm -rf run.out
.PHONY: sysroot/$(ARCH)/include