Broadcom Northstar2 IOMUX Controller

The Northstar2 IOMUX controller supports group based mux configuration. There
are some individual pins that support modifying the pinconf parameters.

Required properties:

- compatible:
    Must be "brcm,ns2-pinmux"

- reg:
    Define the base and range of the I/O address space that contains the
    Northstar2 IOMUX and pin configuration registers.

Properties in sub nodes:

- function:
    The mux function to select

- groups:
    The list of groups to select with a given function

- pins:
    List of pin names to change configuration

The generic properties bias-disable, bias-pull-down, bias-pull-up,
drive-strength, slew-rate, input-enable, input-disable are supported
for some individual pins listed at the end.

For more details, refer to
Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt

For example:

	pinctrl: pinctrl@6501d130 {
		compatible = "brcm,ns2-pinmux";
		reg = <0x6501d130 0x08>,
		      <0x660a0028 0x04>,
		      <0x660009b0 0x40>;

		pinctrl-names = "default";
		pinctrl-0 = <&nand_sel>, <&uart3_rx>, <&sdio0_d4>;

		/* Select nand function */
		nand_sel: nand_sel {
			function = "nand";
			groups = "nand_grp";
		};

		/* Pull up the uart3 rx pin */
		uart3_rx: uart3_rx {
			pins = "uart3_sin";
			bias-pull-up;
		};

		/* Set the drive strength of sdio d4 pin */
		sdio0_d4: sdio0_d4 {
			pins = "sdio0_data4";
			drive-strength = <8>;
		};
	};

List of supported functions and groups in Northstar2:

"nand": "nand_grp"

"nor": "nor_data_grp", "nor_adv_grp", "nor_addr_0_3_grp", "nor_addr_4_5_grp",
	"nor_addr_6_7_grp", "nor_addr_8_9_grp", "nor_addr_10_11_grp",
	"nor_addr_12_15_grp"

"gpio": "gpio_0_1_grp", "gpio_2_5_grp", "gpio_6_7_grp", "gpio_8_9_grp",
	"gpio_10_11_grp", "gpio_12_13_grp", "gpio_14_17_grp", "gpio_18_19_grp",
	"gpio_20_21_grp", "gpio_22_23_grp", "gpio_24_25_grp", "gpio_26_27_grp",
	"gpio_28_29_grp", "gpio_30_31_grp"

"pcie": "pcie_ab1_clk_wak_grp", "pcie_a3_clk_wak_grp", "pcie_b3_clk_wak_grp",
	"pcie_b2_clk_wak_grp", "pcie_a2_clk_wak_grp"

"uart0": "uart0_modem_grp", "uart0_rts_cts_grp", "uart0_in_out_grp"

"uart1": "uart1_ext_clk_grp", "uart1_dcd_dsr_grp", "uart1_ri_dtr_grp",
	"uart1_rts_cts_grp", "uart1_in_out_grp"

"uart2": "uart2_rts_cts_grp"

"pwm": "pwm_0_grp", "pwm_1_grp", "pwm_2_grp", "pwm_3_grp"


List of pins that support pinconf parameters:

"qspi_wp", "qspi_hold", "qspi_cs", "qspi_sck", "uart3_sin", "uart3_sout",
"qspi_mosi", "qspi_miso", "spi0_fss", "spi0_rxd", "spi0_txd", "spi0_sck",
"spi1_fss", "spi1_rxd", "spi1_txd", "spi1_sck", "sdio0_data7",
"sdio0_emmc_rst", "sdio0_led_on", "sdio0_wp", "sdio0_data3", "sdio0_data4",
"sdio0_data5", "sdio0_data6", "sdio0_cmd", "sdio0_data0", "sdio0_data1",
"sdio0_data2", "sdio1_led_on", "sdio1_wp", "sdio0_cd_l", "sdio0_clk",
"sdio1_data5", "sdio1_data6", "sdio1_data7", "sdio1_emmc_rst", "sdio1_data1",
"sdio1_data2", "sdio1_data3", "sdio1_data4", "sdio1_cd_l", "sdio1_clk",
"sdio1_cmd", "sdio1_data0", "ext_mdio_0", "ext_mdc_0", "usb3_p1_vbus_ppc",
"usb3_p1_overcurrent", "usb3_p0_vbus_ppc", "usb3_p0_overcurrent",
"usb2_presence_indication", "usb2_vbus_present", "usb2_vbus_ppc",
"usb2_overcurrent", "sata_led1", "sata_led0"