Lantiq XWAY pinmux controller

Required properties:
- compatible:	"lantiq,<chip>-pinctrl", where <chip> is:
		"ase" (XWAY AMAZON Family)
		"danube" (XWAY DANUBE Family)
		"xrx100" (XWAY xRX100 Family)
		"xrx200" (XWAY xRX200 Family)
		"xrx300" (XWAY xRX300 Family)
- reg: Should contain the physical address and length of the gpio/pinmux
  register range

Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the meaning of the
phrase "pin configuration node".

Lantiq's pin configuration nodes act as a container for an arbitrary number of
subnodes. Each of these subnodes represents some desired configuration for a
pin, a group, or a list of pins or groups. This configuration can include the
mux function to select on those group(s), and two pin configuration parameters:
pull-up and open-drain

The name of each subnode is not important as long as it is unique; all subnodes
should be enumerated and processed purely based on their content.

Each subnode only affects those parameters that are explicitly listed. In
other words, a subnode that lists a mux function but no pin configuration
parameters implies no information about any pin configuration parameters.
Similarly, a pin subnode that describes a pullup parameter implies no
information about e.g. the mux function.

We support 2 types of nodes.

Definition of mux function groups:

Required subnode-properties:
- lantiq,groups : An array of strings. Each string contains the name of a group.
  Valid values for these names are listed below.
- lantiq,function: A string containing the name of the function to mux to the
  group. Valid values for function names are listed below.

Valid values for group and function names:

AMAZON:
  mux groups:
    exin0, exin1, exin2, jtag, spi_di, spi_do, spi_clk, spi_cs1, spi_cs2,
    spi_cs3, spi_cs4, spi_cs5, spi_cs6, asc, stp, gpt1, gpt2, gpt3, clkout0,
    clkout1, clkout2, mdio, dfe led0, dfe led1, ephy led0, ephy led1, ephy led2

  functions:
    spi, asc, cgu, jtag, exin, stp, gpt, mdio, ephy, dfe

DANUBE:
  mux groups:
    exin0, exin1, exin2, jtag, ebu a23, ebu a24, ebu a25, ebu clk, ebu cs1,
    ebu wait, nand ale, nand cs1, nand cle, spi_di, spi_do, spi_clk, spi_cs1,
    spi_cs2, spi_cs3, spi_cs4, spi_cs5, spi_cs6, asc0, asc0 cts rts, stp, nmi,
    gpt1, gpt2, gpt3, clkout0, clkout1, clkout2, clkout3, gnt1, gnt2, gnt3,
    req1, req2, req3, dfe led0, dfe led1

  functions:
    spi, asc, cgu, jtag, exin, stp, gpt, nmi, pci, ebu, dfe

xRX100:
  mux groups:
    exin0, exin1, exin2, exin3, exin4, ebu a23, ebu a24, ebu a25, ebu clk,
    ebu cs1, ebu wait, nand ale, nand cs1, nand cle, nand rdy, nand rd,
    spi_di, spi_do, spi_clk, spi_cs1, spi_cs2, spi_cs3, spi_cs4, spi_cs5,
    spi_cs6, asc0, asc0 cts rts, stp, nmi, gpt1, gpt2, gpt3, clkout0, clkout1,
    clkout2, clkout3, gnt1, gnt2, gnt3, gnt4, req1, req2, req3, req4, mdio,
    dfe led0, dfe led1

  functions:
    spi, asc, cgu, exin, stp, gpt, nmi, pci, ebu, mdio, dfe

xRX200:
  mux groups:
    exin0, exin1, exin2, exin3, exin4, ebu a23, ebu a24, ebu a25, ebu clk,
    ebu cs1, ebu wait, nand ale, nand cs1, nand cle, nand rdy, nand rd,
    spi_di, spi_do, spi_clk, spi_cs1, spi_cs2, spi_cs3, spi_cs4, spi_cs5,
    spi_cs6, usif uart_rx, usif uart_tx, usif uart_rts, usif uart_cts,
    usif uart_dtr, usif uart_dsr, usif uart_dcd, usif uart_ri, usif spi_di,
    usif spi_do, usif spi_clk, usif spi_cs0, usif spi_cs1, usif spi_cs2,
    stp, nmi, gpt1, gpt2, gpt3, clkout0, clkout1, clkout2, clkout3, gnt1,
    gnt2, gnt3, gnt4, req1, req2, req3, req4, mdio, dfe led0, dfe led1,
    gphy0 led0, gphy0 led1, gphy0 led2, gphy1 led0, gphy1 led1, gphy1 led2

  functions:
    spi, usif, cgu, exin, stp, gpt, nmi, pci, ebu, mdio, dfe, gphy

xRX300:
  mux groups:
    exin0, exin1, exin2, exin4, nand ale, nand cs0, nand cs1, nand cle,
    nand rdy, nand rd, nand_d0, nand_d1, nand_d2, nand_d3, nand_d4, nand_d5,
    nand_d6, nand_d7, nand_d1, nand wr, nand wp, nand se, spi_di, spi_do,
    spi_clk, spi_cs1, spi_cs4, spi_cs6, usif uart_rx, usif uart_tx,
    usif spi_di, usif spi_do, usif spi_clk, usif spi_cs0, stp, clkout2,
    mdio, dfe led0, dfe led1, ephy0 led0, ephy0 led1, ephy1 led0, ephy1 led1

  functions:
    spi, usif, cgu, exin, stp, ebu, mdio, dfe, ephy


Definition of pin configurations:

Required subnode-properties:
- lantiq,pins : An array of strings. Each string contains the name of a pin.
  Valid values for these names are listed below.

Optional subnode-properties:
- lantiq,pull: Integer, representing the pull-down/up to apply to the pin.
    0: none, 1: down, 2: up.
- lantiq,open-drain: Boolean, enables open-drain on the defined pin.

Valid values for AMAZON pin names:
  Pinconf pins can be referenced via the names io0-io31.

Valid values for DANUBE pin names:
  Pinconf pins can be referenced via the names io0-io31.

Valid values for xRX100 pin names:
  Pinconf pins can be referenced via the names io0-io55.

Valid values for xRX200 pin names:
  Pinconf pins can be referenced via the names io0-io49.

Valid values for xRX300 pin names:
  Pinconf pins can be referenced via the names io0-io1,io3-io6,io8-io11,
						io13-io19,io23-io27,io34-io36,
						io42-io43,io48-io61.

Example:
	gpio: pinmux@e100b10 {
		compatible = "lantiq,danube-pinctrl";
		pinctrl-names = "default";
		pinctrl-0 = <&state_default>;

		#gpio-cells = <2>;
		gpio-controller;
		reg = <0xE100B10 0xA0>;

		state_default: pinmux {
			stp {
				lantiq,groups = "stp";
				lantiq,function = "stp";
			};
			pci {
				lantiq,groups = "gnt1";
				lantiq,function = "pci";
			};
			conf_out {
				lantiq,pins = "io4", "io5", "io6"; /* stp */
				lantiq,open-drain;
				lantiq,pull = <0>;
			};
		};
	};