// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
*/
/ {
aliases {
serial0 = &uart13;
};
chosen {
stdout-path = "serial0:115200n8";
};
gpio-keys {
compatible = "gpio-keys";
key-volume-up {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
gpios = <&pm7550_gpios 6 GPIO_ACTIVE_LOW>;
debounce-interval = <10>;
linux,can-disable;
wakeup-source;
};
};
pmic-glink {
compatible = "qcom,eliza-pmic-glink",
"qcom,sm8550-pmic-glink",
"qcom,pmic-glink";
#address-cells = <1>;
#size-cells = <0>;
orientation-gpios = <&tlmm 122 GPIO_ACTIVE_HIGH>;
connector@0 {
compatible = "usb-c-connector";
reg = <0>;
power-role = "dual";
data-role = "dual";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
pmic_glink_hs_in: endpoint {
remote-endpoint = <&usb_dwc3_hs>;
};
};
port@1 {
reg = <1>;
pmic_glink_ss_in: endpoint {
remote-endpoint = <&usb_dp_qmpphy_out>;
};
};
};
};
};
vreg_0p9: regulator-0v9 {
compatible = "regulator-fixed";
regulator-name = "VREG_0P9";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <900000>;
regulator-always-on;
regulator-boot-on;
};
vreg_1p8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "VREG_1P8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
vreg_pcie_m_3p3: regulator-3p3 {
compatible = "regulator-fixed";
regulator-name = "vreg_3p3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio_expander1 6 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
connector-0 {
compatible = "pcie-m2-e-connector";
vpcie3v3-supply = <&vreg_pcie_m_3p3>;
w-disable1-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
w-disable2-gpios = <&pm8550vs_g_gpios 4 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&m2_w_disable1>, <&m2_w_disable2>;
pinctrl-names = "default";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
m2_e_pcie_ep: endpoint@0 {
reg = <0>;
remote-endpoint = <&pcieport0_ep>;
};
};
port@3 {
reg = <3>;
#address-cells = <1>;
#size-cells = <0>;
m2_e_uart_ep: endpoint@0 {
reg = <0>;
remote-endpoint = <&uart5_ep>;
};
};
};
};
};
&i2c4 {
pinctrl-0 = <&qup_i2c4_data_clk>;
pinctrl-names = "default";
clock-frequency = <400000>;
status = "okay";
gpio_expander1: gpio@3c {
compatible = "ti,tca9538";
#gpio-cells = <2>;
gpio-controller;
reg = <0x3c>;
};
};
&pcie0 {
status = "okay";
};
&pcie0_phy {
vdda-phy-supply = <&vreg_l1k>;
vdda-pll-supply = <&vreg_l3k>;
status = "okay";
};
&pcie0_port0 {
wake-gpios = <&tlmm 114 GPIO_ACTIVE_LOW>;
reset-gpios = <&tlmm 78 GPIO_ACTIVE_LOW>;
port {
pcieport0_ep: endpoint {
remote-endpoint = <&m2_e_pcie_ep>;
};
};
};
&pon_pwrkey {
status = "okay";
};
&pon_resin {
linux,code = <KEY_VOLUMEDOWN>;
status = "okay";
};
&pm7550ba_eusb2_repeater {
vdd18-supply = <&vreg_l7b>;
vdd3-supply = <&vreg_l17b>;
};
&sdhc_2 {
vmmc-supply = <&vreg_l13b>;
vqmmc-supply = <&vreg_l23b>;
cd-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&sdc2_default>, <&sd_cd>;
pinctrl-1 = <&sdc2_sleep>, <&sd_cd>;
pinctrl-names = "default", "sleep";
status = "okay";
};
&tlmm {
sd_cd: sd-cd-state {
pins = "gpio58";
function = "gpio";
bias-pull-up;
};
};
&pcie1 {
iommu-map = <0x0 &apps_smmu 0x1400 0x0 0x1>,
<0x100 &apps_smmu 0x1401 0x0 0x1>,
<0x208 &apps_smmu 0x1402 0x0 0x1>,
<0x210 &apps_smmu 0x1403 0x0 0x1>,
<0x218 &apps_smmu 0x1404 0x0 0x1>,
<0x300 &apps_smmu 0x1405 0x0 0x1>,
<0x400 &apps_smmu 0x1406 0x0 0x1>,
<0x500 &apps_smmu 0x1407 0x0 0x1>,
<0x501 &apps_smmu 0x1408 0x0 0x1>;
status = "okay";
};
&pcie1_phy {
vdda-phy-supply = <&vreg_l1k>;
vdda-pll-supply = <&vreg_l3k>;
status = "okay";
};
&pcie1_port0 {
wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
/* Same GPIO is used for both PERST# and resx-gpio */
tc9563: pcie@0,0 {
compatible = "pci1179,0623";
reg = <0x10000 0x0 0x0 0x0 0x0>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
ranges;
bus-range = <0x2 0xff>;
vddc-supply = <&vreg_0p9>;
vdd18-supply = <&vreg_1p8>;
vdd09-supply = <&vreg_0p9>;
vddio1-supply = <&vreg_1p8>;
vddio2-supply = <&vreg_1p8>;
vddio18-supply = <&vreg_1p8>;
i2c-parent = <&i2c4 0x77>;
resx-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
pcie@1,0 {
reg = <0x20800 0x0 0x0 0x0 0x0>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
ranges;
bus-range = <0x3 0xff>;
};
pcie@2,0 {
reg = <0x21000 0x0 0x0 0x0 0x0>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
ranges;
bus-range = <0x4 0xff>;
};
pcie@3,0 {
reg = <0x21800 0x0 0x0 0x0 0x0>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
ranges;
bus-range = <0x5 0xff>;
ethernet@0,0 {
reg = <0x50000 0x0 0x0 0x0 0x0>;
};
ethernet@0,1 {
reg = <0x50100 0x0 0x0 0x0 0x0>;
};
};
};
};
&uart13 {
compatible = "qcom,geni-debug-uart";
status = "okay";
};
&usb {
status = "okay";
};
&usb_dp_qmpphy {
vdda-phy-supply = <&vreg_l3g>;
vdda-pll-supply = <&vreg_l7k>;
status = "okay";
};
&usb_dp_qmpphy_out {
remote-endpoint = <&pmic_glink_ss_in>;
};
&usb_dwc3_hs {
remote-endpoint = <&pmic_glink_hs_in>;
};
&usb_hsphy {
vdd-supply = <&vreg_l7k>;
vdda12-supply = <&vreg_l4b>;
phys = <&pm7550ba_eusb2_repeater>;
status = "okay";
};
&uart5 {
status = "okay";
port {
uart5_ep: endpoint {
remote-endpoint = <&m2_e_uart_ep>;
};
};
};
&pm8550vs_g_gpios {
m2_w_disable2: m2-w-disable2-state {
pins = "gpio4";
function = "normal";
input-disable;
output-enable;
bias-disable;
power-source = <2>;
};
};
&tlmm {
m2_w_disable1: m2-w-disable1-state {
pins = "gpio35";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};