// SPDX-License-Identifier: GPL-2.0 /* * Copyright (c) 2021-2022 BayLibre, SAS. * Authors: * Fabien Parent <fparent@baylibre.com> * Bernhard Rosenkränzer <bero@baylibre.com> */ /dts-v1/; #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> #include <dt-bindings/pinctrl/mt8365-pinfunc.h> #include "mt8365.dtsi" #include "mt6357.dtsi" / { model = "MediaTek MT8365 Open Platform EVK"; compatible = "mediatek,mt8365-evk", "mediatek,mt8365"; aliases { serial0 = &uart0; }; chosen { stdout-path = "serial0:921600n8"; }; firmware { optee { compatible = "linaro,optee-tz"; method = "smc"; }; }; gpio-keys { compatible = "gpio-keys"; pinctrl-names = "default"; pinctrl-0 = <&gpio_keys>; key-volume-up { gpios = <&pio 24 GPIO_ACTIVE_LOW>; label = "volume_up"; linux,code = <KEY_VOLUMEUP>; wakeup-source; debounce-interval = <15>; }; }; memory@40000000 { device_type = "memory"; reg = <0 0x40000000 0 0xc0000000>; }; usb_otg_vbus: regulator-0 { compatible = "regulator-fixed"; regulator-name = "otg_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; gpio = <&pio 16 GPIO_ACTIVE_HIGH>; enable-active-high; }; reserved-memory { #address-cells = <2>; #size-cells = <2>; ranges; /* 192 KiB reserved for ARM Trusted Firmware (BL31) */ bl31_secmon_reserved: secmon@43000000 { no-map; reg = <0 0x43000000 0 0x30000>; }; /* 12 MiB reserved for OP-TEE (BL32) * +-----------------------+ 0x43e0_0000 * | SHMEM 2MiB | * +-----------------------+ 0x43c0_0000 * | | TA_RAM 8MiB | * + TZDRAM +--------------+ 0x4340_0000 * | | TEE_RAM 2MiB | * +-----------------------+ 0x4320_0000 */ optee_reserved: optee@43200000 { no-map; reg = <0 0x43200000 0 0x00c00000>; }; }; }; &cpu0 { proc-supply = <&mt6357_vproc_reg>; sram-supply = <&mt6357_vsram_proc_reg>; }; &cpu1 { proc-supply = <&mt6357_vproc_reg>; sram-supply = <&mt6357_vsram_proc_reg>; }; &cpu2 { proc-supply = <&mt6357_vproc_reg>; sram-supply = <&mt6357_vsram_proc_reg>; }; &cpu3 { proc-supply = <&mt6357_vproc_reg>; sram-supply = <&mt6357_vsram_proc_reg>; }; ðernet { pinctrl-0 = <ðernet_pins>; pinctrl-names = "default"; phy-handle = <ð_phy>; phy-mode = "rmii"; /* * Ethernet and HDMI (DSI0) are sharing pins. * Only one can be enabled at a time and require the physical switch * SW2101 to be set on LAN position * mt6357_vibr_reg and mt6357_vsim2_reg are needed to supply ethernet */ status = "disabled"; mdio { #address-cells = <1>; #size-cells = <0>; eth_phy: ethernet-phy@0 { reg = <0>; }; }; }; &i2c0 { clock-frequency = <100000>; pinctrl-0 = <&i2c0_pins>; pinctrl-names = "default"; status = "okay"; }; &mmc0 { assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>; assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; bus-width = <8>; cap-mmc-highspeed; cap-mmc-hw-reset; hs400-ds-delay = <0x12012>; max-frequency = <200000000>; mmc-hs200-1_8v; mmc-hs400-1_8v; no-sd; no-sdio; non-removable; pinctrl-0 = <&mmc0_default_pins>; pinctrl-1 = <&mmc0_uhs_pins>; pinctrl-names = "default", "state_uhs"; vmmc-supply = <&mt6357_vemc_reg>; vqmmc-supply = <&mt6357_vio18_reg>; status = "okay"; }; &mmc1 { bus-width = <4>; cap-sd-highspeed; cd-gpios = <&pio 76 GPIO_ACTIVE_LOW>; max-frequency = <200000000>; pinctrl-0 = <&mmc1_default_pins>; pinctrl-1 = <&mmc1_uhs_pins>; pinctrl-names = "default", "state_uhs"; sd-uhs-sdr104; sd-uhs-sdr50; vmmc-supply = <&mt6357_vmch_reg>; vqmmc-supply = <&mt6357_vmc_reg>; status = "okay"; }; &mt6357_pmic { interrupts-extended = <&pio 145 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; #interrupt-cells = <2>; }; &pio { ethernet_pins: ethernet-pins { phy_reset_pins { pinmux = <MT8365_PIN_133_TDM_TX_DATA1__FUNC_GPIO133>; }; rmii_pins { pinmux = <MT8365_PIN_0_GPIO0__FUNC_EXT_TXD0>, <MT8365_PIN_1_GPIO1__FUNC_EXT_TXD1>, <MT8365_PIN_2_GPIO2__FUNC_EXT_TXD2>, <MT8365_PIN_3_GPIO3__FUNC_EXT_TXD3>, <MT8365_PIN_4_GPIO4__FUNC_EXT_TXC>, <MT8365_PIN_5_GPIO5__FUNC_EXT_RXER>, <MT8365_PIN_6_GPIO6__FUNC_EXT_RXC>, <MT8365_PIN_7_GPIO7__FUNC_EXT_RXDV>, <MT8365_PIN_8_GPIO8__FUNC_EXT_RXD0>, <MT8365_PIN_9_GPIO9__FUNC_EXT_RXD1>, <MT8365_PIN_10_GPIO10__FUNC_EXT_RXD2>, <MT8365_PIN_11_GPIO11__FUNC_EXT_RXD3>, <MT8365_PIN_12_GPIO12__FUNC_EXT_TXEN>, <MT8365_PIN_13_GPIO13__FUNC_EXT_COL>, <MT8365_PIN_14_GPIO14__FUNC_EXT_MDIO>, <MT8365_PIN_15_GPIO15__FUNC_EXT_MDC>; }; }; gpio_keys: gpio-keys-pins { pins { pinmux = <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>; bias-pull-up; input-enable; }; }; i2c0_pins: i2c0-pins { pins { pinmux = <MT8365_PIN_57_SDA0__FUNC_SDA0_0>, <MT8365_PIN_58_SCL0__FUNC_SCL0_0>; bias-pull-up; }; }; mmc0_default_pins: mmc0-default-pins { clk-pins { pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>; bias-pull-down; }; cmd-dat-pins { pinmux = <MT8365_PIN_103_MSDC0_DAT0__FUNC_MSDC0_DAT0>, <MT8365_PIN_102_MSDC0_DAT1__FUNC_MSDC0_DAT1>, <MT8365_PIN_101_MSDC0_DAT2__FUNC_MSDC0_DAT2>, <MT8365_PIN_100_MSDC0_DAT3__FUNC_MSDC0_DAT3>, <MT8365_PIN_96_MSDC0_DAT4__FUNC_MSDC0_DAT4>, <MT8365_PIN_95_MSDC0_DAT5__FUNC_MSDC0_DAT5>, <MT8365_PIN_94_MSDC0_DAT6__FUNC_MSDC0_DAT6>, <MT8365_PIN_93_MSDC0_DAT7__FUNC_MSDC0_DAT7>, <MT8365_PIN_98_MSDC0_CMD__FUNC_MSDC0_CMD>; input-enable; bias-pull-up; }; rst-pins { pinmux = <MT8365_PIN_97_MSDC0_RSTB__FUNC_MSDC0_RSTB>; bias-pull-up; }; }; mmc0_uhs_pins: mmc0-uhs-pins { clk-pins { pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>; drive-strength = <MTK_DRIVE_10mA>; bias-pull-down = <MTK_PUPD_SET_R1R0_10>; }; cmd-dat-pins { pinmux = <MT8365_PIN_103_MSDC0_DAT0__FUNC_MSDC0_DAT0>, <MT8365_PIN_102_MSDC0_DAT1__FUNC_MSDC0_DAT1>, <MT8365_PIN_101_MSDC0_DAT2__FUNC_MSDC0_DAT2>, <MT8365_PIN_100_MSDC0_DAT3__FUNC_MSDC0_DAT3>, <MT8365_PIN_96_MSDC0_DAT4__FUNC_MSDC0_DAT4>, <MT8365_PIN_95_MSDC0_DAT5__FUNC_MSDC0_DAT5>, <MT8365_PIN_94_MSDC0_DAT6__FUNC_MSDC0_DAT6>, <MT8365_PIN_93_MSDC0_DAT7__FUNC_MSDC0_DAT7>, <MT8365_PIN_98_MSDC0_CMD__FUNC_MSDC0_CMD>; input-enable; drive-strength = <MTK_DRIVE_10mA>; bias-pull-up = <MTK_PUPD_SET_R1R0_01>; }; ds-pins { pinmux = <MT8365_PIN_104_MSDC0_DSL__FUNC_MSDC0_DSL>; drive-strength = <MTK_DRIVE_10mA>; bias-pull-down = <MTK_PUPD_SET_R1R0_10>; }; rst-pins { pinmux = <MT8365_PIN_97_MSDC0_RSTB__FUNC_MSDC0_RSTB>; drive-strength = <MTK_DRIVE_10mA>; bias-pull-up; }; }; mmc1_default_pins: mmc1-default-pins { cd-pins { pinmux = <MT8365_PIN_76_CMDAT8__FUNC_GPIO76>; bias-pull-up; }; clk-pins { pinmux = <MT8365_PIN_88_MSDC1_CLK__FUNC_MSDC1_CLK>; bias-pull-down = <MTK_PUPD_SET_R1R0_10>; }; cmd-dat-pins { pinmux = <MT8365_PIN_89_MSDC1_DAT0__FUNC_MSDC1_DAT0>, <MT8365_PIN_90_MSDC1_DAT1__FUNC_MSDC1_DAT1>, <MT8365_PIN_91_MSDC1_DAT2__FUNC_MSDC1_DAT2>, <MT8365_PIN_92_MSDC1_DAT3__FUNC_MSDC1_DAT3>, <MT8365_PIN_87_MSDC1_CMD__FUNC_MSDC1_CMD>; input-enable; bias-pull-up = <MTK_PUPD_SET_R1R0_01>; }; }; mmc1_uhs_pins: mmc1-uhs-pins { clk-pins { pinmux = <MT8365_PIN_88_MSDC1_CLK__FUNC_MSDC1_CLK>; drive-strength = <MTK_DRIVE_8mA>; bias-pull-down = <MTK_PUPD_SET_R1R0_10>; }; cmd-dat-pins { pinmux = <MT8365_PIN_89_MSDC1_DAT0__FUNC_MSDC1_DAT0>, <MT8365_PIN_90_MSDC1_DAT1__FUNC_MSDC1_DAT1>, <MT8365_PIN_91_MSDC1_DAT2__FUNC_MSDC1_DAT2>, <MT8365_PIN_92_MSDC1_DAT3__FUNC_MSDC1_DAT3>, <MT8365_PIN_87_MSDC1_CMD__FUNC_MSDC1_CMD>; input-enable; drive-strength = <MTK_DRIVE_6mA>; bias-pull-up = <MTK_PUPD_SET_R1R0_01>; }; }; uart0_pins: uart0-pins { pins { pinmux = <MT8365_PIN_35_URXD0__FUNC_URXD0>, <MT8365_PIN_36_UTXD0__FUNC_UTXD0>; }; }; uart1_pins: uart1-pins { pins { pinmux = <MT8365_PIN_37_URXD1__FUNC_URXD1>, <MT8365_PIN_38_UTXD1__FUNC_UTXD1>; }; }; uart2_pins: uart2-pins { pins { pinmux = <MT8365_PIN_39_URXD2__FUNC_URXD2>, <MT8365_PIN_40_UTXD2__FUNC_UTXD2>; }; }; usb_pins: usb-pins { id-pins { pinmux = <MT8365_PIN_17_GPIO17__FUNC_GPIO17>; input-enable; bias-pull-up; }; usb0-vbus-pins { pinmux = <MT8365_PIN_16_GPIO16__FUNC_USB_DRVVBUS>; output-high; }; usb1-vbus-pins { pinmux = <MT8365_PIN_18_GPIO18__FUNC_GPIO18>; output-high; }; }; pwm_pins: pwm-pins { pins { pinmux = <MT8365_PIN_19_DISP_PWM__FUNC_PWM_A>, <MT8365_PIN_116_I2S_BCK__FUNC_PWM_C>; }; }; }; &pwm { pinctrl-0 = <&pwm_pins>; pinctrl-names = "default"; status = "okay"; }; &ssusb { dr_mode = "otg"; maximum-speed = "high-speed"; pinctrl-0 = <&usb_pins>; pinctrl-names = "default"; usb-role-switch; vusb33-supply = <&mt6357_vusb33_reg>; status = "okay"; connector { compatible = "gpio-usb-b-connector", "usb-b-connector"; id-gpios = <&pio 17 GPIO_ACTIVE_HIGH>; type = "micro"; vbus-supply = <&usb_otg_vbus>; }; }; &usb_host { vusb33-supply = <&mt6357_vusb33_reg>; status = "okay"; }; &uart0 { pinctrl-0 = <&uart0_pins>; pinctrl-names = "default"; status = "okay"; }; &uart1 { pinctrl-0 = <&uart1_pins>; pinctrl-names = "default"; status = "okay"; }; &uart2 { pinctrl-0 = <&uart2_pins>; pinctrl-names = "default"; status = "okay"; };