// SPDX-License-Identifier: GPL-2.0+
/*
* dts file for Xilinx ZynqMP ZCU106
*
* (C) Copyright 2016 - 2022, Xilinx, Inc.
* (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
*
* Michal Simek <michal.simek@amd.com>
*/
/dts-v1/;
#include "zynqmp.dtsi"
#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
#include <dt-bindings/phy/phy.h>
/ {
model = "ZynqMP ZCU106 RevA";
compatible = "xlnx,zynqmp-zcu106-revA", "xlnx,zynqmp-zcu106", "xlnx,zynqmp";
aliases {
ethernet0 = &gem3;
i2c0 = &i2c0;
i2c1 = &i2c1;
mmc0 = &sdhci1;
nvmem0 = &eeprom;
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
spi0 = &qspi;
usb0 = &usb0;
};
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
};
gpio-keys {
compatible = "gpio-keys";
autorepeat;
switch-19 {
label = "sw19";
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_DOWN>;
wakeup-source;
autorepeat;
};
};
leds {
compatible = "gpio-leds";
heartbeat-led {
label = "heartbeat";
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
ina226-u76 {
compatible = "iio-hwmon";
io-channels = <&u76 0>, <&u76 1>, <&u76 2>, <&u76 3>;
};
ina226-u77 {
compatible = "iio-hwmon";
io-channels = <&u77 0>, <&u77 1>, <&u77 2>, <&u77 3>;
};
ina226-u78 {
compatible = "iio-hwmon";
io-channels = <&u78 0>, <&u78 1>, <&u78 2>, <&u78 3>;
};
ina226-u87 {
compatible = "iio-hwmon";
io-channels = <&u87 0>, <&u87 1>, <&u87 2>, <&u87 3>;
};
ina226-u85 {
compatible = "iio-hwmon";
io-channels = <&u85 0>, <&u85 1>, <&u85 2>, <&u85 3>;
};
ina226-u86 {
compatible = "iio-hwmon";
io-channels = <&u86 0>, <&u86 1>, <&u86 2>, <&u86 3>;
};
ina226-u93 {
compatible = "iio-hwmon";
io-channels = <&u93 0>, <&u93 1>, <&u93 2>, <&u93 3>;
};
ina226-u88 {
compatible = "iio-hwmon";
io-channels = <&u88 0>, <&u88 1>, <&u88 2>, <&u88 3>;
};
ina226-u15 {
compatible = "iio-hwmon";
io-channels = <&u15 0>, <&u15 1>, <&u15 2>, <&u15 3>;
};
ina226-u92 {
compatible = "iio-hwmon";
io-channels = <&u92 0>, <&u92 1>, <&u92 2>, <&u92 3>;
};
ina226-u79 {
compatible = "iio-hwmon";
io-channels = <&u79 0>, <&u79 1>, <&u79 2>, <&u79 3>;
};
ina226-u81 {
compatible = "iio-hwmon";
io-channels = <&u81 0>, <&u81 1>, <&u81 2>, <&u81 3>;
};
ina226-u80 {
compatible = "iio-hwmon";
io-channels = <&u80 0>, <&u80 1>, <&u80 2>, <&u80 3>;
};
ina226-u84 {
compatible = "iio-hwmon";
io-channels = <&u84 0>, <&u84 1>, <&u84 2>, <&u84 3>;
};
ina226-u16 {
compatible = "iio-hwmon";
io-channels = <&u16 0>, <&u16 1>, <&u16 2>, <&u16 3>;
};
ina226-u65 {
compatible = "iio-hwmon";
io-channels = <&u65 0>, <&u65 1>, <&u65 2>, <&u65 3>;
};
ina226-u74 {
compatible = "iio-hwmon";
io-channels = <&u74 0>, <&u74 1>, <&u74 2>, <&u74 3>;
};
ina226-u75 {
compatible = "iio-hwmon";
io-channels = <&u75 0>, <&u75 1>, <&u75 2>, <&u75 3>;
};
/* 48MHz reference crystal */
ref48: ref48M {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <48000000>;
};
refhdmi: refhdmi {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <114285000>;
};
dpcon {
compatible = "dp-connector";
label = "P11";
type = "full-size";
port {
dpcon_in: endpoint {
remote-endpoint = <&dpsub_dp_out>;
};
};
};
};
&can1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1_default>;
};
&dcc {
status = "okay";
};
&fpd_dma_chan1 {
status = "okay";
};
&fpd_dma_chan2 {
status = "okay";
};
&fpd_dma_chan3 {
status = "okay";
};
&fpd_dma_chan4 {
status = "okay";
};
&fpd_dma_chan5 {
status = "okay";
};
&fpd_dma_chan6 {
status = "okay";
};
&fpd_dma_chan7 {
status = "okay";
};
&fpd_dma_chan8 {
status = "okay";
};
&gem3 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gem3_default>;
mdio: mdio {
#address-cells = <1>;
#size-cells = <0>;
phy0: ethernet-phy@c {
#phy-cells = <1>;
reg = <0xc>;
compatible = "ethernet-phy-id2000.a231";
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
ti,fifo-depth = <0x1>;
ti,dp83867-rxctrl-strap-quirk;
reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
};
};
};
&gpio {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio_default>;
};
&gpu {
status = "okay";
};
&i2c0 {
status = "okay";
clock-frequency = <400000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c0_default>;
pinctrl-1 = <&pinctrl_i2c0_gpio>;
scl-gpios = <&gpio 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
tca6416_u97: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
gpio-controller; /* interrupt not connected */
#gpio-cells = <2>;
/*
* IRQ not connected
* Lines:
* 0 - SFP_SI5328_INT_ALM
* 1 - HDMI_SI5328_INT_ALM
* 5 - IIC_MUX_RESET_B
* 6 - GEM3_EXP_RESET_B
* 10 - FMC_HPC0_PRSNT_M2C_B
* 11 - FMC_HPC1_PRSNT_M2C_B
* 2-4, 7, 12-17 - not connected
*/
};
tca6416_u61: gpio@21 {
compatible = "ti,tca6416";
reg = <0x21>;
gpio-controller;
#gpio-cells = <2>;
/*
* IRQ not connected
* Lines:
* 0 - VCCPSPLL_EN
* 1 - MGTRAVCC_EN
* 2 - MGTRAVTT_EN
* 3 - VCCPSDDRPLL_EN
* 4 - MIO26_PMU_INPUT_LS
* 5 - PL_PMBUS_ALERT
* 6 - PS_PMBUS_ALERT
* 7 - MAXIM_PMBUS_ALERT
* 10 - PL_DDR4_VTERM_EN
* 11 - PL_DDR4_VPP_2V5_EN
* 12 - PS_DIMM_VDDQ_TO_PSVCCO_ON
* 13 - PS_DIMM_SUSPEND_EN
* 14 - PS_DDR4_VTERM_EN
* 15 - PS_DDR4_VPP_2V5_EN
* 16 - 17 - not connected
*/
};
i2c-mux@75 { /* u60 */
compatible = "nxp,pca9544";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x75>;
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
/* PS_PMBUS */
u76: ina226@40 { /* u76 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u76";
reg = <0x40>;
shunt-resistor = <5000>;
};
u77: ina226@41 { /* u77 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u77";
reg = <0x41>;
shunt-resistor = <5000>;
};
u78: ina226@42 { /* u78 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u78";
reg = <0x42>;
shunt-resistor = <5000>;
};
u87: ina226@43 { /* u87 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u87";
reg = <0x43>;
shunt-resistor = <5000>;
};
u85: ina226@44 { /* u85 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u85";
reg = <0x44>;
shunt-resistor = <5000>;
};
u86: ina226@45 { /* u86 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u86";
reg = <0x45>;
shunt-resistor = <5000>;
};
u93: ina226@46 { /* u93 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u93";
reg = <0x46>;
shunt-resistor = <5000>;
};
u88: ina226@47 { /* u88 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u88";
reg = <0x47>;
shunt-resistor = <5000>;
};
u15: ina226@4a { /* u15 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u15";
reg = <0x4a>;
shunt-resistor = <5000>;
};
u92: ina226@4b { /* u92 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u92";
reg = <0x4b>;
shunt-resistor = <5000>;
};
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
/* PL_PMBUS */
u79: ina226@40 { /* u79 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u79";
reg = <0x40>;
shunt-resistor = <2000>;
};
u81: ina226@41 { /* u81 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u81";
reg = <0x41>;
shunt-resistor = <5000>;
};
u80: ina226@42 { /* u80 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u80";
reg = <0x42>;
shunt-resistor = <5000>;
};
u84: ina226@43 { /* u84 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u84";
reg = <0x43>;
shunt-resistor = <5000>;
};
u16: ina226@44 { /* u16 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u16";
reg = <0x44>;
shunt-resistor = <5000>;
};
u65: ina226@45 { /* u65 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u65";
reg = <0x45>;
shunt-resistor = <5000>;
};
u74: ina226@46 { /* u74 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u74";
reg = <0x46>;
shunt-resistor = <5000>;
};
u75: ina226@47 { /* u75 */
compatible = "ti,ina226";
#io-channel-cells = <1>;
label = "ina226-u75";
reg = <0x47>;
shunt-resistor = <5000>;
};
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
/* MAXIM_PMBUS - 00 */
max15301@a { /* u46 */
compatible = "maxim,max15301";
reg = <0xa>;
};
max15303@b { /* u4 */
compatible = "maxim,max15303";
reg = <0xb>;
};
max15303@10 { /* u13 */
compatible = "maxim,max15303";
reg = <0x10>;
};
max15301@13 { /* u47 */
compatible = "maxim,max15301";
reg = <0x13>;
};
max15303@14 { /* u7 */
compatible = "maxim,max15303";
reg = <0x14>;
};
max15303@15 { /* u6 */
compatible = "maxim,max15303";
reg = <0x15>;
};
max15303@16 { /* u10 */
compatible = "maxim,max15303";
reg = <0x16>;
};
max15303@17 { /* u9 */
compatible = "maxim,max15303";
reg = <0x17>;
};
max15301@18 { /* u63 */
compatible = "maxim,max15301";
reg = <0x18>;
};
max15303@1a { /* u49 */
compatible = "maxim,max15303";
reg = <0x1a>;
};
max15303@1b { /* u8 */
compatible = "maxim,max15303";
reg = <0x1b>;
};
max15303@1d { /* u18 */
compatible = "maxim,max15303";
reg = <0x1d>;
};
max20751@72 { /* u95 */
compatible = "maxim,max20751";
reg = <0x72>;
};
max20751@73 { /* u96 */
compatible = "maxim,max20751";
reg = <0x73>;
};
};
/* Bus 3 is not connected */
};
};
&i2c1 {
status = "okay";
clock-frequency = <400000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1_default>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
/* PL i2c via PCA9306 - u45 */
i2c-mux@74 { /* u34 */
compatible = "nxp,pca9548";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x74>;
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
/*
* IIC_EEPROM 1kB memory which uses 256B blocks
* where every block has different address.
* 0 - 256B address 0x54
* 256B - 512B address 0x55
* 512B - 768B address 0x56
* 768B - 1024B address 0x57
*/
eeprom: eeprom@54 { /* u23 */
compatible = "atmel,24c08";
reg = <0x54>;
};
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
si5341: clock-generator@36 { /* SI5341 - u69 */
compatible = "silabs,si5341";
reg = <0x36>;
#clock-cells = <2>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&ref48>;
clock-names = "xtal";
clock-output-names = "si5341";
si5341_0: out@0 {
/* refclk0 for PS-GT, used for DP */
reg = <0>;
always-on;
};
si5341_2: out@2 {
/* refclk2 for PS-GT, used for USB3 */
reg = <2>;
always-on;
};
si5341_3: out@3 {
/* refclk3 for PS-GT, used for SATA */
reg = <3>;
always-on;
};
si5341_6: out@6 {
/* refclk6 PL CLK125 */
reg = <6>;
always-on;
};
si5341_7: out@7 {
/* refclk7 PL CLK74 */
reg = <7>;
always-on;
};
si5341_9: out@9 {
/* refclk9 used for PS_REF_CLK 33.3 MHz */
reg = <9>;
always-on;
};
};
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
si570_1: clock-generator@5d { /* USER SI570 - u42 */
#clock-cells = <0>;
compatible = "silabs,si570";
reg = <0x5d>;
temperature-stability = <50>;
factory-fout = <300000000>;
clock-frequency = <300000000>;
clock-output-names = "si570_user";
};
};
i2c@3 {
#address-cells = <1>;
#size-cells = <0>;
reg = <3>;
si570_2: clock-generator@5d { /* USER MGT SI570 - u56 */
#clock-cells = <0>;
compatible = "silabs,si570";
reg = <0x5d>;
temperature-stability = <50>; /* copy from zc702 */
factory-fout = <156250000>;
clock-frequency = <148500000>;
clock-output-names = "si570_mgt";
};
};
i2c@4 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
/* SI5328 - u20 */
};
i2c@5 {
#address-cells = <1>;
#size-cells = <0>;
reg = <5>; /* FAN controller */
temp@4c {/* lm96163 - u128 */
compatible = "national,lm96163";
reg = <0x4c>;
};
};
/* 6 - 7 unconnected */
};
i2c-mux@75 {
compatible = "nxp,pca9548"; /* u135 */
#address-cells = <1>;
#size-cells = <0>;
reg = <0x75>;
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
/* HPC0_IIC */
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
/* HPC1_IIC */
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
/* SYSMON */
};
i2c@3 {
#address-cells = <1>;
#size-cells = <0>;
reg = <3>;
/* DDR4 SODIMM */
};
i2c@4 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
/* SEP 3 */
};
i2c@5 {
#address-cells = <1>;
#size-cells = <0>;
reg = <5>;
/* SEP 2 */
};
i2c@6 {
#address-cells = <1>;
#size-cells = <0>;
reg = <6>;
/* SEP 1 */
};
i2c@7 {
#address-cells = <1>;
#size-cells = <0>;
reg = <7>;
/* SEP 0 */
};
};
};
&pinctrl0 {
status = "okay";
pinctrl_i2c0_default: i2c0-default {
mux {
groups = "i2c0_3_grp";
function = "i2c0";
};
conf {
groups = "i2c0_3_grp";
bias-pull-up;
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
};
pinctrl_i2c0_gpio: i2c0-gpio {
mux {
groups = "gpio0_14_grp", "gpio0_15_grp";
function = "gpio0";
};
conf {
groups = "gpio0_14_grp", "gpio0_15_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
};
pinctrl_i2c1_default: i2c1-default {
mux {
groups = "i2c1_4_grp";
function = "i2c1";
};
conf {
groups = "i2c1_4_grp";
bias-pull-up;
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
};
pinctrl_i2c1_gpio: i2c1-gpio {
mux {
groups = "gpio0_16_grp", "gpio0_17_grp";
function = "gpio0";
};
conf {
groups = "gpio0_16_grp", "gpio0_17_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
};
pinctrl_uart0_default: uart0-default {
mux {
groups = "uart0_4_grp";
function = "uart0";
};
conf {
groups = "uart0_4_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO18";
bias-high-impedance;
};
conf-tx {
pins = "MIO19";
bias-disable;
};
};
pinctrl_uart1_default: uart1-default {
mux {
groups = "uart1_5_grp";
function = "uart1";
};
conf {
groups = "uart1_5_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO21";
bias-high-impedance;
};
conf-tx {
pins = "MIO20";
bias-disable;
};
};
pinctrl_usb0_default: usb0-default {
mux {
groups = "usb0_0_grp";
function = "usb0";
};
conf {
groups = "usb0_0_grp";
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO52", "MIO53", "MIO55";
bias-high-impedance;
drive-strength = <12>;
slew-rate = <SLEW_RATE_FAST>;
};
conf-tx {
pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
"MIO60", "MIO61", "MIO62", "MIO63";
bias-disable;
drive-strength = <4>;
slew-rate = <SLEW_RATE_SLOW>;
};
};
pinctrl_gem3_default: gem3-default {
mux {
function = "ethernet3";
groups = "ethernet3_0_grp";
};
conf {
groups = "ethernet3_0_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
"MIO75";
bias-high-impedance;
low-power-disable;
};
conf-tx {
pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
"MIO69";
bias-disable;
low-power-enable;
};
mux-mdio {
function = "mdio3";
groups = "mdio3_0_grp";
};
conf-mdio {
groups = "mdio3_0_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
bias-disable;
};
};
pinctrl_can1_default: can1-default {
mux {
function = "can1";
groups = "can1_6_grp";
};
conf {
groups = "can1_6_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO25";
bias-high-impedance;
};
conf-tx {
pins = "MIO24";
bias-disable;
};
};
pinctrl_sdhci1_default: sdhci1-default {
mux {
groups = "sdio1_0_grp";
function = "sdio1";
};
conf {
groups = "sdio1_0_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
bias-disable;
};
mux-cd {
groups = "sdio1_cd_0_grp";
function = "sdio1_cd";
};
conf-cd {
groups = "sdio1_cd_0_grp";
bias-high-impedance;
bias-pull-up;
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
mux-wp {
groups = "sdio1_wp_0_grp";
function = "sdio1_wp";
};
conf-wp {
groups = "sdio1_wp_0_grp";
bias-high-impedance;
bias-pull-up;
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
};
pinctrl_gpio_default: gpio-default {
mux {
function = "gpio0";
groups = "gpio0_22_grp", "gpio0_23_grp";
};
conf {
groups = "gpio0_22_grp", "gpio0_23_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
mux-msp {
function = "gpio0";
groups = "gpio0_13_grp", "gpio0_38_grp";
};
conf-msp {
groups = "gpio0_13_grp", "gpio0_38_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-pull-up {
pins = "MIO22";
bias-pull-up;
};
conf-pull-none {
pins = "MIO13", "MIO23", "MIO38";
bias-disable;
};
};
};
&psgtr {
status = "okay";
/* nc, sata, usb3, dp */
clocks = <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>;
clock-names = "ref1", "ref2", "ref3";
};
&qspi {
status = "okay";
flash@0 {
compatible = "m25p80", "jedec,spi-nor"; /* 16MB + 16MB */
#address-cells = <1>;
#size-cells = <1>;
reg = <0x0>;
spi-tx-bus-width = <4>;
spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
spi-max-frequency = <108000000>; /* Based on DC1 spec */
};
};
&rtc {
status = "okay";
};
&sata {
status = "okay";
/* SATA OOB timing settings */
ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
phy-names = "sata-phy";
phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
};
/* SD1 with level shifter */
&sdhci1 {
status = "okay";
/*
* This property should be removed for supporting UHS mode
*/
no-1-8-v;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdhci1_default>;
xlnx,mio-bank = <1>;
};
&uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0_default>;
};
&uart1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1_default>;
};
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
phy-names = "usb3-phy";
phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
maximum-speed = "super-speed";
};
&watchdog0 {
status = "okay";
};
&zynqmp_dpdma {
status = "okay";
};
&zynqmp_dpsub {
status = "okay";
phy-names = "dp-phy0", "dp-phy1";
phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
<&psgtr 0 PHY_TYPE_DP 1 3>;
ports {
port@5 {
dpsub_dp_out: endpoint {
remote-endpoint = <&dpcon_in>;
};
};
};
};