// SPDX-License-Identifier: GPL-2.0-only /* * Copyright (C) 2021 Sancloud Ltd * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ */ /dts-v1/; #include "am33xx.dtsi" #include "am335x-bone-common.dtsi" #include "am335x-boneblack-common.dtsi" #include "am335x-sancloud-bbe-common.dtsi" #include <dt-bindings/interrupt-controller/irq.h> / { model = "SanCloud BeagleBone Enhanced Extended WiFi"; compatible = "sancloud,am335x-boneenhanced", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; wlan_en_reg: fixedregulator@2 { compatible = "regulator-fixed"; regulator-name = "wlan-en-regulator"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; startup-delay-us = <100000>; }; }; &am33xx_pinmux { mmc3_pins: mmc3-pins { pinctrl-single,pins = < /* gpmc_a9.gpio1_25: RADIO_EN */ AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_OUTPUT_PULLUP, MUX_MODE7) /* gpmc_ad12.mmc2_dat0 */ AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLUP, MUX_MODE3) /* gpmc_ad13.mmc2_dat1 */ AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLUP, MUX_MODE3) /* gpmc_ad14.mmc2_dat2 */ AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_INPUT_PULLUP, MUX_MODE3) /* gpmc_ad15.mmc2_dat3 */ AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLUP, MUX_MODE3) /* gpmc_csn3.mmc2_cmd */ AM33XX_PADCONF(AM335X_PIN_GPMC_CSN3, PIN_INPUT_PULLUP, MUX_MODE3) /* gpmc_clk.mmc2_clk */ AM33XX_PADCONF(AM335X_PIN_GPMC_CLK, PIN_INPUT_PULLUP, MUX_MODE3) >; }; bluetooth_pins: bluetooth-pins { pinctrl-single,pins = < /* event_intr0.gpio0_19 */ AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_INPUT_PULLUP, MUX_MODE7) >; }; uart1_pins: uart1-pins { pinctrl-single,pins = < /* uart1_rxd */ AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT, MUX_MODE0) /* uart1_txd */ AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_INPUT, MUX_MODE0) /* uart1_ctsn */ AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE0) /* uart1_rtsn */ AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT_PULLDOWN, MUX_MODE0) >; }; }; &i2c2 { status = "disabled"; }; &mmc3 { status = "okay"; vmmc-supply = <&wlan_en_reg>; bus-width = <4>; non-removable; cap-power-off-card; ti,needs-special-hs-handling; keep-power-in-suspend; pinctrl-names = "default"; pinctrl-0 = <&mmc3_pins>; dmas = <&edma_xbar 12 0 1 &edma_xbar 13 0 2>; dma-names = "tx", "rx"; clock-frequency = <50000000>; max-frequency = <50000000>; }; &uart1 { status = "okay"; bluetooth { pinctrl-names = "default"; pinctrl-0 = <&uart1_pins &bluetooth_pins>; compatible = "qcom,qca6174-bt"; enable-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>; clocks = <&l4ls_clkctrl AM3_L4LS_UART2_CLKCTRL 0>; interrupt-parent = <&gpio0>; interrupts = <19 IRQ_TYPE_EDGE_RISING>; }; };