// SPDX-License-Identifier: GPL-2.0 /* * Samsung's Exynos4212 based Galaxy Tab 3 board common source * * Copyright (c) 2013 Samsung Electronics Co., Ltd. * http://www.samsung.com */ /dts-v1/; #include "exynos4212.dtsi" #include "exynos4412-ppmu-common.dtsi" #include "exynos-mfc-reserved-memory.dtsi" #include <dt-bindings/clock/samsung,s2mps11.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/leds/common.h> #include <dt-bindings/input/gpio-keys.h> #include <dt-bindings/input/input.h> #include <dt-bindings/interrupt-controller/irq.h> #include "exynos-pinctrl.h" / { compatible = "samsung,tab3", "samsung,exynos4212", "samsung,exynos4"; memory@40000000 { device_type = "memory"; /* * Technically 1.5GB is available, but the latter 512MB is handled * in a special way by downstream (every second page is skipped), * and thus doesn't initialize correctly on mainline. Only 1020M is * used for now. */ reg = <0x40000000 0x3fc00000>; }; aliases { mmc0 = &mshc_0; /* Internal storage */ mmc1 = &sdhci_2; /* SD card */ mmc2 = &sdhci_3; /* WiFi */ }; chosen { stdout-path = &serial_2; /* Default S-BOOT bootloader loads initramfs here */ linux,initrd-start = <0x42000000>; linux,initrd-end = <0x42800000>; }; firmware@204f000 { compatible = "samsung,secure-firmware"; reg = <0x0204F000 0x1000>; }; fixed-rate-clocks { xxti { compatible = "samsung,clock-xxti"; clock-frequency = <0>; }; xusbxti { compatible = "samsung,clock-xusbxti"; clock-frequency = <24000000>; }; }; gpio-keys { compatible = "gpio-keys"; pinctrl-names = "default"; pinctrl-0 = <&gpio_keys>; key-power { gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; linux,code = <KEY_POWER>; label = "power"; debounce-interval = <10>; wakeup-source; }; key-up { gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; linux,code = <KEY_VOLUMEUP>; label = "volume down"; debounce-interval = <10>; }; key-down { gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; linux,code = <KEY_VOLUMEDOWN>; label = "volume up"; debounce-interval = <10>; }; key-home { gpios = <&gpx1 2 GPIO_ACTIVE_LOW>; linux,code = <KEY_HOME>; label = "home"; debounce-interval = <10>; }; switch-hall-sensor { gpios = <&gpx2 4 GPIO_ACTIVE_LOW>; linux,input-type = <EV_SW>; linux,code = <SW_LID>; linux,can-disable; label = "hall effect sensor"; debounce-interval = <10>; wakeup-source; }; }; led-touchkeys { compatible = "regulator-led"; vled-supply = <&ldo20_reg>; default-state = "off"; function = LED_FUNCTION_KBD_BACKLIGHT; color = <LED_COLOR_ID_WHITE>; }; i2c_max77693: i2c-gpio-1 { compatible = "i2c-gpio"; sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; i2c-gpio,delay-us = <2>; #address-cells = <1>; #size-cells = <0>; pmic@66 { compatible = "maxim,max77693"; reg = <0x66>; interrupt-parent = <&gpx1>; interrupts = <5 IRQ_TYPE_EDGE_FALLING>; pinctrl-names = "default"; pinctrl-0 = <&max77693_irq>; regulators { esafeout1_reg: ESAFEOUT1 { regulator-name = "ESAFEOUT1"; regulator-boot-on; }; esafeout2_reg: ESAFEOUT2 { regulator-name = "ESAFEOUT2"; }; charger_reg: CHARGER { regulator-name = "CHARGER"; regulator-min-microamp = <60000>; regulator-max-microamp = <2580000>; regulator-boot-on; }; }; charger { compatible = "maxim,max77693-charger"; maxim,constant-microvolt = <4350000>; maxim,min-system-microvolt = <3600000>; maxim,thermal-regulation-celsius = <100>; maxim,battery-overcurrent-microamp = <3500000>; maxim,charge-input-threshold-microvolt = <4300000>; }; }; }; i2c_max77693_fuel: i2c-gpio-2 { compatible = "i2c-gpio"; sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; i2c-gpio,delay-us = <2>; #address-cells = <1>; #size-cells = <0>; fuel-gauge@36 { compatible = "maxim,max17050"; reg = <0x36>; interrupt-parent = <&gpx2>; interrupts = <3 IRQ_TYPE_EDGE_FALLING>; pinctrl-names = "default"; pinctrl-0 = <&max77693_fuel_irq>; maxim,over-heat-temp = <500>; maxim,over-volt = <4500>; }; }; i2c_magnetometer: i2c-gpio-3 { compatible = "i2c-gpio"; sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; i2c-gpio,delay-us = <2>; #address-cells = <1>; #size-cells = <0>; magnetometer@2e { compatible = "yamaha,yas532"; reg = <0x2e>; iovdd-supply = <&ldo3_reg>; mount-matrix = "-1", "0", "0", "0", "1", "0", "0", "0", "-1"; }; }; i2c_lightsensor: i2c-gpio-4 { compatible = "i2c-gpio"; sda-gpios = <&gpl0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; scl-gpios = <&gpl0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; i2c-gpio,delay-us = <2>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; /* WiFi model uses CM3323, 3G/LTE use CM36653 */ }; i2c_bl: i2c-gpio-5 { compatible = "i2c-gpio"; sda-gpios = <&gpm4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; scl-gpios = <&gpm4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; #address-cells = <1>; #size-cells = <0>; backlight: backlight@2c { compatible = "ti,lp8556"; reg = <0x2c>; bl-name = "lcd-bl"; dev-ctrl = /bits/ 8 <0x80>; init-brt = /bits/ 8 <0x78>; /* 120 */ power-supply = <&vbatt_reg>; enable-supply = <&backlight_reset_supply>; pwms = <&pwm 1 78770 0>; pwm-names = "lp8556"; rom-a3h { rom-addr = /bits/ 8 <0xa3>; rom-val = /bits/ 8 <0x5e>; }; rom-a5h { rom-addr = /bits/ 8 <0xa5>; rom-val = /bits/ 8 <0x34>; }; rom-a7h { rom-addr = /bits/ 8 <0xa7>; rom-val = /bits/ 8 <0xfa>; }; }; }; vbatt_reg: voltage-regulator-1 { compatible = "regulator-fixed"; regulator-name = "VBATT"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; regulator-always-on; }; backlight_reset_supply: voltage-regulator-2 { compatible = "regulator-fixed"; regulator-name = "BACKLIGHT_ENVDDIO"; pinctrl-names = "default"; pinctrl-0 = <&backlight_reset>; gpio = <&gpm0 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; display_3v3_supply: voltage-regulator-3 { compatible = "regulator-fixed"; regulator-name = "DISPLAY_3.3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; pinctrl-names = "default"; pinctrl-0 = <&lcd_en>; gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; /* LCD_EN */ enable-active-high; }; mic_bias_reg: voltage-regulator-4 { compatible = "regulator-fixed"; regulator-name = "MICBIAS_LDO_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; }; submic_bias_reg: voltage-regulator-5 { compatible = "regulator-fixed"; regulator-name = "SUB_MICBIAS_LDO_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; }; sound: sound { compatible = "samsung,midas-audio"; model = "TAB3"; mic-bias-supply = <&mic_bias_reg>; submic-bias-supply = <&submic_bias_reg>; samsung,audio-routing = "HP", "HPOUT1L", "HP", "HPOUT1R", "SPK", "SPKOUTLN", "SPK", "SPKOUTLP", "SPK", "SPKOUTRN", "SPK", "SPKOUTRP", "RCV", "HPOUT2N", "RCV", "HPOUT2P", "LINE", "LINEOUT2N", "LINE", "LINEOUT2P", "HDMI", "LINEOUT1N", "HDMI", "LINEOUT1P", "IN2LP:VXRN", "MICBIAS1", "IN2LN", "MICBIAS1", "Main Mic", "MICBIAS1", "IN1RP", "MICBIAS2", "IN1RN", "MICBIAS2", "Sub Mic", "MICBIAS2", "IN1LP", "Headset Mic", "IN1LN", "Headset Mic"; cpu { sound-dai = <&i2s0 0>; }; codec { sound-dai = <&wm1811>; }; }; wlan_pwrseq: sdhci3-pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>; clocks = <&s5m8767_osc S2MPS11_CLK_BT>; clock-names = "ext_clock"; }; }; &bus_acp { devfreq = <&bus_dmc>; status = "okay"; }; &bus_c2c { devfreq = <&bus_dmc>; status = "okay"; }; &bus_display { devfreq = <&bus_leftbus>; status = "okay"; }; &bus_dmc { devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; vdd-supply = <&buck1_reg>; status = "okay"; }; &bus_fsys { devfreq = <&bus_leftbus>; status = "okay"; }; &bus_leftbus { devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; vdd-supply = <&buck3_reg>; status = "okay"; }; &bus_mfc { devfreq = <&bus_leftbus>; status = "okay"; }; &bus_peri { devfreq = <&bus_leftbus>; status = "okay"; }; &bus_rightbus { devfreq = <&bus_leftbus>; status = "okay"; }; &cpu0 { cpu0-supply = <&buck2_reg>; }; &cpu_thermal { cooling-maps { map0 { /* Corresponds to 800MHz at freq_table */ cooling-device = <&cpu0 7 7>, <&cpu1 7 7>; }; map1 { /* Corresponds to 200MHz at freq_table */ cooling-device = <&cpu0 13 13>, <&cpu1 13 13>; }; }; }; &dsi_0 { vddcore-supply = <&ldo8_reg>; vddio-supply = <&ldo10_reg>; samsung,burst-clock-frequency = <500000000>; samsung,esc-clock-frequency = <20000000>; samsung,pll-clock-frequency = <24000000>; status = "okay"; panel@0 { compatible = "samsung,lsl080al02", "samsung,s6d7aa0"; reg = <0>; power-supply = <&display_3v3_supply>; pinctrl-names = "default"; pinctrl-0 = <&lcd_nrst>; reset-gpios = <&gpf0 4 GPIO_ACTIVE_LOW>; backlight = <&backlight>; }; }; &exynos_usbphy { vbus-supply = <&esafeout1_reg>; status = "okay"; }; &fimd { status = "okay"; }; &gpu { mali-supply = <&buck4_reg>; status = "okay"; }; &hsotg { vusb_d-supply = <&ldo15_reg>; vusb_a-supply = <&ldo12_reg>; dr_mode = "otg"; status = "okay"; }; &i2c_1 { pinctrl-0 = <&i2c1_bus>; pinctrl-names = "default"; status = "okay"; lis3dh: accelerometer@19 { /* K2DH seems to be the same as lis2dh12 in terms of registers */ compatible = "st,lis2dh12-accel"; reg = <0x19>; interrupt-parent = <&gpx0>; interrupts = <0 IRQ_TYPE_EDGE_FALLING>; vdd-supply = <&ldo17_reg>; vddio-supply = <&ldo3_reg>; mount-matrix = "-1", "0", "0", "0", "1", "0", "0", "0", "-1"; }; }; &i2c_3 { samsung,i2c-sda-delay = <100>; samsung,i2c-slave-addr = <0x10>; samsung,i2c-max-bus-freq = <400000>; pinctrl-0 = <&i2c3_bus>; pinctrl-names = "default"; status = "okay"; touchscreen@48 { /* MELFAS MMS252, using MMS114 compatible for now */ compatible = "melfas,mms114"; reg = <0x48>; interrupt-parent = <&gpb>; interrupts = <4 IRQ_TYPE_EDGE_FALLING>; touchscreen-size-x = <800>; touchscreen-size-y = <1280>; avdd-supply = <&ldo21_reg>; vdd-supply = <&ldo25_reg>; linux,keycodes = <KEY_MENU KEY_BACK>; }; }; &i2c_4 { samsung,i2c-sda-delay = <100>; samsung,i2c-slave-addr = <0x10>; samsung,i2c-max-bus-freq = <100000>; pinctrl-0 = <&i2c4_bus>; pinctrl-names = "default"; status = "okay"; wm1811: audio-codec@1a { compatible = "wlf,wm1811"; reg = <0x1a>; clocks = <&pmu_system_controller 0>; clock-names = "MCLK1"; interrupt-controller; #interrupt-cells = <2>; interrupt-parent = <&gpx3>; interrupts = <6 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; #sound-dai-cells = <0>; wlf,gpio-cfg = <0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x8000 0x0 0x0 0x0>; wlf,micbias-cfg = <0x25 0x2f>; wlf,lineout1-feedback; wlf,lineout1-se; wlf,lineout2-se; wlf,ldoena-always-driven; AVDD2-supply = <&ldo3_reg>; CPVDD-supply = <&ldo3_reg>; DBVDD1-supply = <&ldo3_reg>; DBVDD2-supply = <&ldo3_reg>; DBVDD3-supply = <&ldo3_reg>; SPKVDD1-supply = <&vbatt_reg>; SPKVDD2-supply = <&vbatt_reg>; wlf,ldo1ena-gpios = <&gpm4 4 GPIO_ACTIVE_HIGH>; wlf,ldo2ena-gpios = <&gpm4 4 GPIO_ACTIVE_HIGH>; }; }; &i2c_7 { samsung,i2c-sda-delay = <100>; samsung,i2c-slave-addr = <0x10>; samsung,i2c-max-bus-freq = <100000>; pinctrl-0 = <&i2c7_bus>; pinctrl-names = "default"; status = "okay"; s5m8767: pmic@66 { compatible = "samsung,s5m8767-pmic"; reg = <0x66>; interrupt-parent = <&gpx0>; interrupts = <7 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>; wakeup-source; s5m8767,pmic-buck-default-dvs-idx = <1>; s5m8767,pmic-buck-dvs-gpios = <&gpm3 0 GPIO_ACTIVE_HIGH>, <&gpm3 1 GPIO_ACTIVE_HIGH>, <&gpm3 2 GPIO_ACTIVE_HIGH>; s5m8767,pmic-buck-ds-gpios = <&gpf3 1 GPIO_ACTIVE_HIGH>, <&gpf3 2 GPIO_ACTIVE_HIGH>, <&gpf3 3 GPIO_ACTIVE_HIGH>; s5m8767,pmic-buck2-dvs-voltage = <1100000>, <1100000>, <1100000>, <1100000>, <1100000>, <1100000>, <1100000>, <1100000>; s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, <1100000>, <1100000>, <1100000>, <1100000>, <1100000>, <1100000>; s5m8767,pmic-buck4-dvs-voltage = <1100000>, <1100000>, <1100000>, <1100000>, <1100000>, <1100000>, <1100000>, <1100000>; regulators { ldo1_reg: LDO1 { regulator-name = "VALIVE_1.0V_AP"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; regulator-always-on; regulator-boot-on; op_mode = <1>; }; ldo2_reg: LDO2 { regulator-name = "VM1M2_1.2V_AP"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-always-on; regulator-boot-on; op_mode = <1>; }; ldo3_reg: LDO3 { regulator-name = "VCC_1.8V_AP"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; op_mode = <1>; }; ldo5_reg: LDO5 { regulator-name = "VCC_3.3V_MHL"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; op_mode = <1>; }; ldo8_reg: LDO8 { regulator-name = "VMIPI_1.0V"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; op_mode = <3>; }; ldo9_reg: LDO9 { regulator-name = "VSIL_1.2V"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; op_mode = <1>; }; ldo10_reg: LDO10 { regulator-name = "VMIPI_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; op_mode = <3>; }; ldo12_reg: LDO12 { regulator-name = "VUOTG_3.0V"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; op_mode = <1>; regulator-state-mem { regulator-off-in-suspend; }; }; ldo13_reg: LDO13 { regulator-name = "VCC_1.8V_MHL"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; op_mode = <1>; }; ldo15_reg: LDO15 { regulator-name = "VHSIC_1.0V"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; op_mode = <1>; regulator-state-mem { regulator-on-in-suspend; }; }; ldo17_reg: LDO17 { regulator-name = "VCC_2.8V_AP"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; op_mode = <1>; regulator-always-on; }; ldo19_reg: LDO19 { regulator-name = "VLED_IC_1.9V"; regulator-min-microvolt = <1900000>; regulator-max-microvolt = <1900000>; op_mode = <1>; regulator-always-on; }; ldo20_reg: LDO20 { regulator-name = "VTOUCH_3.3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; op_mode = <1>; }; ldo21_reg: LDO21 { regulator-name = "TSP_VDD_3.3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; op_mode = <1>; }; ldo22_reg: LDO22 { regulator-name = "5M_AF_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; op_mode = <1>; }; ldo23_reg: LDO23 { regulator-name = "VTF_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; op_mode = <3>; }; ldo24_reg: LDO24 { regulator-name = "LEDA_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; op_mode = <1>; }; ldo25_reg: LDO25 { regulator-name = "TSP_VDD_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; op_mode = <1>; }; ldo26_reg: LDO26 { regulator-name = "CAM_IO_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; op_mode = <1>; }; ldo27_reg: LDO27 { regulator-name = "VTCAM_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; op_mode = <1>; }; buck1_reg: BUCK1 { regulator-name = "VDD_MIF"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1100000>; regulator-always-on; regulator-boot-on; op_mode = <3>; }; buck2_reg: BUCK2 { regulator-name = "VDD_ARM"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1500000>; regulator-always-on; regulator-boot-on; op_mode = <3>; }; buck3_reg: BUCK3 { regulator-name = "VDD_INT"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1300000>; regulator-always-on; regulator-boot-on; op_mode = <3>; }; buck4_reg: BUCK4 { regulator-name = "VDD_G3D"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1150000>; regulator-boot-on; op_mode = <3>; }; buck5_reg: BUCK5 { regulator-name = "VMEM_1.2V_AP"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-always-on; regulator-boot-on; op_mode = <1>; }; buck6_reg: BUCK6 { regulator-name = "CAM_ISP_CORE_1.2V"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; op_mode = <1>; regulator-state-mem { regulator-off-in-suspend; }; }; }; s5m8767_osc: clocks { compatible = "samsung,s5m8767-clk"; #clock-cells = <1>; clock-output-names = "en32khz_ap", "en32khz_cp", "en32khz_bt"; }; }; }; &i2s0 { pinctrl-0 = <&i2s0_bus>; pinctrl-names = "default"; status = "okay"; }; &mshc_0 { broken-cd; non-removable; card-detect-delay = <200>; vmmc-supply = <&ldo22_reg>; clock-frequency = <400000000>; samsung,dw-mshc-ciu-div = <0>; samsung,dw-mshc-sdr-timing = <2 3>; samsung,dw-mshc-ddr-timing = <1 2>; pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; pinctrl-names = "default"; bus-width = <8>; cap-mmc-highspeed; mmc-ddr-1_8v; status = "okay"; }; &pinctrl_0 { pinctrl-names = "default"; pinctrl-0 = <&sleep0>; lcd_en: lcd-en-pins { samsung,pins = "gpc0-1"; samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; }; lcd_nrst: lcd-nrst-pins { samsung,pins = "gpf0-4"; samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; }; s5m8767_ds: s5m8767-ds-pins { samsung,pins = "gpf3-1", "gpf3-2", "gpf3-3"; samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; }; sleep0: sleep-state { PIN_SLP(gpa0-0, INPUT, NONE); PIN_SLP(gpa0-1, OUT0, NONE); PIN_SLP(gpa0-2, INPUT, NONE); PIN_SLP(gpa0-3, INPUT, UP); PIN_SLP(gpa0-4, INPUT, DOWN); PIN_SLP(gpa0-5, INPUT, DOWN); PIN_SLP(gpa0-6, INPUT, DOWN); PIN_SLP(gpa0-7, INPUT, DOWN); PIN_SLP(gpa1-0, INPUT, DOWN); PIN_SLP(gpa1-1, INPUT, DOWN); PIN_SLP(gpa1-2, INPUT, DOWN); PIN_SLP(gpa1-3, INPUT, DOWN); PIN_SLP(gpa1-4, INPUT, DOWN); PIN_SLP(gpa1-5, INPUT, DOWN); PIN_SLP(gpb-0, INPUT, NONE); PIN_SLP(gpb-1, INPUT, NONE); PIN_SLP(gpb-2, INPUT, NONE); PIN_SLP(gpb-3, INPUT, NONE); PIN_SLP(gpb-4, INPUT, DOWN); PIN_SLP(gpb-5, INPUT, DOWN); PIN_SLP(gpb-6, INPUT, DOWN); PIN_SLP(gpb-7, INPUT, DOWN); PIN_SLP(gpc0-0, INPUT, DOWN); PIN_SLP(gpc0-1, INPUT, DOWN); PIN_SLP(gpc0-2, INPUT, NONE); PIN_SLP(gpc0-3, INPUT, NONE); PIN_SLP(gpc0-4, INPUT, NONE); PIN_SLP(gpc1-0, INPUT, DOWN); PIN_SLP(gpc1-1, INPUT, DOWN); PIN_SLP(gpc1-2, INPUT, DOWN); PIN_SLP(gpc1-3, INPUT, DOWN); PIN_SLP(gpc1-4, INPUT, DOWN); PIN_SLP(gpd0-0, INPUT, DOWN); PIN_SLP(gpd0-1, OUT0, NONE); PIN_SLP(gpd0-2, INPUT, NONE); PIN_SLP(gpd0-3, INPUT, NONE); PIN_SLP(gpd1-0, INPUT, DOWN); PIN_SLP(gpd1-1, INPUT, DOWN); PIN_SLP(gpd1-2, INPUT, NONE); PIN_SLP(gpd1-3, INPUT, NONE); PIN_SLP(gpf0-0, INPUT, DOWN); PIN_SLP(gpf0-1, INPUT, DOWN); PIN_SLP(gpf0-2, INPUT, DOWN); PIN_SLP(gpf0-3, INPUT, DOWN); PIN_SLP(gpf0-4, OUT0, NONE); PIN_SLP(gpf0-5, OUT0, NONE); PIN_SLP(gpf0-6, INPUT, DOWN); PIN_SLP(gpf0-7, INPUT, DOWN); PIN_SLP(gpf1-0, INPUT, DOWN); PIN_SLP(gpf1-1, INPUT, DOWN); PIN_SLP(gpf1-2, INPUT, DOWN); PIN_SLP(gpf1-3, INPUT, DOWN); PIN_SLP(gpf1-4, INPUT, DOWN); PIN_SLP(gpf1-5, INPUT, DOWN); PIN_SLP(gpf1-6, INPUT, DOWN); PIN_SLP(gpf1-7, INPUT, DOWN); PIN_SLP(gpf2-0, INPUT, DOWN); PIN_SLP(gpf2-1, INPUT, DOWN); PIN_SLP(gpf2-2, INPUT, DOWN); PIN_SLP(gpf2-3, INPUT, DOWN); PIN_SLP(gpf2-4, INPUT, DOWN); PIN_SLP(gpf2-5, INPUT, DOWN); PIN_SLP(gpf2-6, INPUT, DOWN); PIN_SLP(gpf2-7, INPUT, DOWN); PIN_SLP(gpf3-0, INPUT, DOWN); PIN_SLP(gpf3-1, INPUT, DOWN); PIN_SLP(gpf3-2, INPUT, DOWN); PIN_SLP(gpf3-3, INPUT, DOWN); PIN_SLP(gpf3-4, PREV, NONE); PIN_SLP(gpf3-5, OUT0, DOWN); PIN_SLP(gpj0-0, INPUT, DOWN); PIN_SLP(gpj0-1, INPUT, DOWN); PIN_SLP(gpj0-2, INPUT, DOWN); PIN_SLP(gpj0-3, OUT0, NONE); PIN_SLP(gpj0-4, INPUT, DOWN); PIN_SLP(gpj0-5, INPUT, DOWN); PIN_SLP(gpj0-6, OUT0, NONE); PIN_SLP(gpj0-7, OUT0, NONE); PIN_SLP(gpj1-0, OUT0, NONE); PIN_SLP(gpj1-1, INPUT, DOWN); PIN_SLP(gpj1-2, PREV, NONE); PIN_SLP(gpj1-3, INPUT, DOWN); PIN_SLP(gpj1-4, INPUT, DOWN); }; }; &pinctrl_1 { pinctrl-names = "default"; pinctrl-0 = <&sleep1>; bt_shutdown: bt-shutdown-pins { samsung,pins = "gpl0-6"; samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; }; bt_host_wakeup: bt-host-wakeup-pins { samsung,pins = "gpx2-6"; samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; }; bt_device_wakeup: bt-device-wakeup-pins { samsung,pins = "gpx3-1"; samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; }; backlight_reset: backlight-reset-pins { samsung,pins = "gpm0-1"; samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; }; gpio_keys: gpio-keys-pins { samsung,pins = "gpx1-2", "gpx2-2", "gpx2-4", "gpx2-7", "gpx3-3"; samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; }; max77693_irq: max77693-irq-pins { samsung,pins = "gpx1-5"; samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; }; max77693_fuel_irq: max77693-fuel-irq-pins { samsung,pins = "gpx2-3"; samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; }; sdhci2_cd: sdhci2-cd-irq-pins { samsung,pins = "gpx3-4"; samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; }; s5m8767_dvs: s5m8767-dvs-pins { samsung,pins = "gpm3-0", "gpm3-1", "gpm3-2"; samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; }; s5m8767_irq: s5m8767-irq-pins { samsung,pins = "gpx0-7"; samsung,pin-function = <EXYNOS_PIN_FUNC_EINT>; samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; }; sleep1: sleep-state { PIN_SLP(gpk0-0, PREV, NONE); PIN_SLP(gpk0-1, PREV, NONE); PIN_SLP(gpk0-2, PREV, NONE); PIN_SLP(gpk0-3, PREV, NONE); PIN_SLP(gpk0-4, PREV, NONE); PIN_SLP(gpk0-5, PREV, NONE); PIN_SLP(gpk0-6, PREV, NONE); PIN_SLP(gpk1-0, INPUT, DOWN); PIN_SLP(gpk1-1, INPUT, DOWN); PIN_SLP(gpk1-2, INPUT, DOWN); PIN_SLP(gpk1-3, PREV, NONE); PIN_SLP(gpk1-4, PREV, NONE); PIN_SLP(gpk1-5, PREV, NONE); PIN_SLP(gpk1-6, PREV, NONE); PIN_SLP(gpk2-0, INPUT, DOWN); PIN_SLP(gpk2-1, INPUT, DOWN); PIN_SLP(gpk2-2, INPUT, DOWN); PIN_SLP(gpk2-3, INPUT, DOWN); PIN_SLP(gpk2-4, INPUT, DOWN); PIN_SLP(gpk2-5, INPUT, DOWN); PIN_SLP(gpk2-6, INPUT, DOWN); PIN_SLP(gpk3-0, OUT0, NONE); PIN_SLP(gpk3-1, INPUT, NONE); PIN_SLP(gpk3-2, INPUT, DOWN); PIN_SLP(gpk3-3, INPUT, NONE); PIN_SLP(gpk3-4, INPUT, NONE); PIN_SLP(gpk3-5, INPUT, NONE); PIN_SLP(gpk3-6, INPUT, NONE); PIN_SLP(gpl0-0, INPUT, DOWN); PIN_SLP(gpl0-1, INPUT, NONE); PIN_SLP(gpl0-2, INPUT, NONE); PIN_SLP(gpl0-3, INPUT, DOWN); PIN_SLP(gpl0-4, INPUT, DOWN); PIN_SLP(gpl0-6, PREV, NONE); PIN_SLP(gpl1-0, INPUT, DOWN); PIN_SLP(gpl1-1, OUT0, NONE); PIN_SLP(gpl2-0, INPUT, DOWN); PIN_SLP(gpl2-1, PREV, NONE); PIN_SLP(gpl2-2, PREV, NONE); PIN_SLP(gpl2-3, INPUT, DOWN); PIN_SLP(gpl2-4, INPUT, DOWN); PIN_SLP(gpl2-5, INPUT, DOWN); PIN_SLP(gpl2-6, INPUT, DOWN); PIN_SLP(gpl2-7, INPUT, DOWN); PIN_SLP(gpm0-0, PREV, NONE); PIN_SLP(gpm0-1, OUT0, NONE); PIN_SLP(gpm0-2, INPUT, DOWN); PIN_SLP(gpm0-3, INPUT, DOWN); PIN_SLP(gpm0-4, INPUT, DOWN); PIN_SLP(gpm0-5, INPUT, DOWN); PIN_SLP(gpm0-6, INPUT, DOWN); PIN_SLP(gpm0-7, INPUT, DOWN); PIN_SLP(gpm1-0, INPUT, DOWN); PIN_SLP(gpm1-1, INPUT, DOWN); PIN_SLP(gpm1-2, INPUT, NONE); PIN_SLP(gpm1-3, INPUT, NONE); PIN_SLP(gpm1-4, INPUT, NONE); PIN_SLP(gpm1-5, INPUT, NONE); PIN_SLP(gpm1-6, OUT0, NONE); PIN_SLP(gpm2-0, INPUT, NONE); PIN_SLP(gpm2-1, INPUT, NONE); PIN_SLP(gpm2-2, OUT0, NONE); PIN_SLP(gpm2-3, INPUT, DOWN); PIN_SLP(gpm2-4, INPUT, DOWN); PIN_SLP(gpm3-0, PREV, NONE); PIN_SLP(gpm3-1, PREV, NONE); PIN_SLP(gpm3-2, PREV, NONE); PIN_SLP(gpm3-3, INPUT, DOWN); PIN_SLP(gpm3-4, INPUT, DOWN); PIN_SLP(gpm3-5, PREV, NONE); PIN_SLP(gpm3-6, INPUT, DOWN); PIN_SLP(gpm3-7, OUT0, NONE); PIN_SLP(gpm4-0, INPUT, DOWN); PIN_SLP(gpm4-1, INPUT, DOWN); PIN_SLP(gpm4-2, INPUT, DOWN); PIN_SLP(gpm4-3, INPUT, DOWN); PIN_SLP(gpm4-4, PREV, NONE); PIN_SLP(gpm4-5, INPUT, NONE); PIN_SLP(gpm4-6, INPUT, DOWN); PIN_SLP(gpm4-7, INPUT, DOWN); PIN_SLP(gpy0-0, INPUT, DOWN); PIN_SLP(gpy0-1, INPUT, DOWN); PIN_SLP(gpy0-2, INPUT, NONE); PIN_SLP(gpy0-3, INPUT, NONE); PIN_SLP(gpy0-4, INPUT, DOWN); PIN_SLP(gpy0-5, INPUT, DOWN); PIN_SLP(gpy1-0, INPUT, DOWN); PIN_SLP(gpy1-1, INPUT, DOWN); PIN_SLP(gpy1-2, INPUT, DOWN); PIN_SLP(gpy1-3, INPUT, DOWN); PIN_SLP(gpy2-0, PREV, NONE); PIN_SLP(gpy2-1, INPUT, DOWN); PIN_SLP(gpy2-2, INPUT, NONE); PIN_SLP(gpy2-3, INPUT, NONE); PIN_SLP(gpy2-4, INPUT, NONE); PIN_SLP(gpy2-5, INPUT, NONE); PIN_SLP(gpy3-0, INPUT, DOWN); PIN_SLP(gpy3-1, INPUT, DOWN); PIN_SLP(gpy3-2, INPUT, DOWN); PIN_SLP(gpy3-3, INPUT, DOWN); PIN_SLP(gpy3-4, INPUT, DOWN); PIN_SLP(gpy3-5, INPUT, DOWN); PIN_SLP(gpy3-6, INPUT, DOWN); PIN_SLP(gpy3-7, INPUT, DOWN); PIN_SLP(gpy4-0, INPUT, DOWN); PIN_SLP(gpy4-1, INPUT, DOWN); PIN_SLP(gpy4-2, INPUT, DOWN); PIN_SLP(gpy4-3, INPUT, DOWN); PIN_SLP(gpy4-4, INPUT, DOWN); PIN_SLP(gpy4-5, INPUT, DOWN); PIN_SLP(gpy4-6, INPUT, DOWN); PIN_SLP(gpy4-7, INPUT, DOWN); PIN_SLP(gpy5-0, INPUT, DOWN); PIN_SLP(gpy5-1, INPUT, DOWN); PIN_SLP(gpy5-2, INPUT, DOWN); PIN_SLP(gpy5-3, INPUT, DOWN); PIN_SLP(gpy5-4, INPUT, DOWN); PIN_SLP(gpy5-5, INPUT, DOWN); PIN_SLP(gpy5-6, INPUT, DOWN); PIN_SLP(gpy5-7, INPUT, DOWN); PIN_SLP(gpy6-0, INPUT, DOWN); PIN_SLP(gpy6-1, INPUT, DOWN); PIN_SLP(gpy6-2, INPUT, DOWN); PIN_SLP(gpy6-3, INPUT, DOWN); PIN_SLP(gpy6-4, INPUT, DOWN); PIN_SLP(gpy6-5, INPUT, DOWN); PIN_SLP(gpy6-6, INPUT, DOWN); PIN_SLP(gpy6-7, INPUT, DOWN); }; }; &pinctrl_2 { pinctrl-names = "default"; pinctrl-0 = <&sleep2>; sleep2: sleep-state { PIN_SLP(gpz-0, INPUT, DOWN); PIN_SLP(gpz-1, INPUT, DOWN); PIN_SLP(gpz-2, INPUT, DOWN); PIN_SLP(gpz-3, INPUT, DOWN); PIN_SLP(gpz-4, INPUT, DOWN); PIN_SLP(gpz-5, INPUT, DOWN); PIN_SLP(gpz-6, INPUT, DOWN); }; }; &pinctrl_3 { pinctrl-names = "default"; pinctrl-0 = <&sleep3>; sleep3: sleep-state { PIN_SLP(gpv0-0, INPUT, DOWN); PIN_SLP(gpv0-1, INPUT, DOWN); PIN_SLP(gpv0-2, INPUT, DOWN); PIN_SLP(gpv0-3, INPUT, DOWN); PIN_SLP(gpv0-4, INPUT, DOWN); PIN_SLP(gpv0-5, INPUT, DOWN); PIN_SLP(gpv0-6, INPUT, DOWN); PIN_SLP(gpv0-7, INPUT, DOWN); PIN_SLP(gpv1-0, INPUT, DOWN); PIN_SLP(gpv1-1, INPUT, DOWN); PIN_SLP(gpv1-2, INPUT, DOWN); PIN_SLP(gpv1-3, INPUT, DOWN); PIN_SLP(gpv1-4, INPUT, DOWN); PIN_SLP(gpv1-5, INPUT, DOWN); PIN_SLP(gpv1-6, INPUT, DOWN); PIN_SLP(gpv1-7, INPUT, DOWN); PIN_SLP(gpv2-0, INPUT, DOWN); PIN_SLP(gpv2-1, INPUT, DOWN); PIN_SLP(gpv2-2, INPUT, DOWN); PIN_SLP(gpv2-3, INPUT, DOWN); PIN_SLP(gpv2-4, INPUT, DOWN); PIN_SLP(gpv2-5, INPUT, DOWN); PIN_SLP(gpv2-6, INPUT, DOWN); PIN_SLP(gpv2-7, INPUT, DOWN); PIN_SLP(gpv3-0, INPUT, DOWN); PIN_SLP(gpv3-1, INPUT, DOWN); PIN_SLP(gpv3-2, INPUT, DOWN); PIN_SLP(gpv3-3, INPUT, DOWN); PIN_SLP(gpv3-4, INPUT, DOWN); PIN_SLP(gpv3-5, INPUT, DOWN); PIN_SLP(gpv3-6, INPUT, DOWN); PIN_SLP(gpv3-7, INPUT, DOWN); PIN_SLP(gpv4-0, INPUT, DOWN); PIN_SLP(gpv4-1, INPUT, DOWN); }; }; &pmu_system_controller { assigned-clocks = <&pmu_system_controller 0>; assigned-clock-parents = <&clock CLK_XUSBXTI>; }; &pwm { pinctrl-0 = <&pwm1_out>; pinctrl-names = "default"; samsung,pwm-outputs = <1>; status = "okay"; }; /* * The internal RTC does not work; instead, the RTC provided by the * S5M8766 PMIC is used. Disable the RTC to make sure the working * one gets used. * * We add this node to avoid DTB check warnings, as the Exynos4 RTC * requires two clocks, and only one is set up by default. */ &rtc { clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>; clock-names = "rtc", "rtc_src"; status = "disabled"; }; &sdhci_2 { bus-width = <4>; cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>; pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>; pinctrl-names = "default"; vmmc-supply = <&ldo23_reg>; status = "okay"; }; &sdhci_3 { #address-cells = <1>; #size-cells = <0>; non-removable; bus-width = <4>; mmc-pwrseq = <&wlan_pwrseq>; pinctrl-names = "default"; pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>; status = "okay"; brcmf: wifi@1 { compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac"; reg = <1>; interrupt-parent = <&gpx2>; interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "host-wake"; }; }; &serial_0 { pinctrl-0 = <&uart0_data &uart0_fctl>; pinctrl-names = "default"; status = "okay"; bluetooth { compatible = "brcm,bcm4330-bt"; /* BCM4334B0 */ pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>; pinctrl-names = "default"; max-speed = <3000000>; shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>; device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>; host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>; clocks = <&s5m8767_osc S2MPS11_CLK_BT>; }; }; &serial_1 { status = "okay"; }; &serial_2 { status = "okay"; }; &serial_3 { status = "okay"; }; &tmu { vtmu-supply = <&ldo10_reg>; status = "okay"; };