RT5682 audio CODEC

This device supports I2C only.

Required properties:

- compatible : "realtek,rt5682" or "realtek,rt5682i"

- reg : The I2C address of the device.

- AVDD-supply: phandle to the regulator supplying analog power through the
  AVDD pin

- MICVDD-supply: phandle to the regulator supplying power for the microphone
  bias through the MICVDD pin. Either MICVDD or VBAT should be present.

- VBAT-supply: phandle to the regulator supplying battery power through the
  VBAT pin. Either MICVDD or VBAT should be present.

- DBVDD-supply: phandle to the regulator supplying I/O power through the DBVDD
  pin.

- LDO1-IN-supply: phandle to the regulator supplying power to the digital core
  and charge pump through the LDO1_IN pin.

Optional properties:

- interrupts : The CODEC's interrupt output.

- realtek,dmic1-data-pin
  0: dmic1 is not used
  1: using GPIO2 pin as dmic1 data pin
  2: using GPIO5 pin as dmic1 data pin

- realtek,dmic1-clk-pin
  0: using GPIO1 pin as dmic1 clock pin
  1: using GPIO3 pin as dmic1 clock pin

- realtek,jd-src
  0: No JD is used
  1: using JD1 as JD source

- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.

- realtek,btndet-delay
  The debounce delay for push button.
  The delay time is realtek,btndet-delay value multiple of 8.192 ms.
  If absent, the default is 16.

- #clock-cells : Should be set to '<1>',  wclk and bclk sources provided.
- clock-output-names : Name given for DAI clocks output.

- clocks : phandle and clock specifier for codec MCLK.
- clock-names : Clock name string for 'clocks' attribute, should be "mclk".

- realtek,dmic-clk-rate-hz : Set the clock rate (hz) for the requirement of
  the particular DMIC.

- realtek,dmic-delay-ms : Set the delay time (ms) for the requirement of
  the particular DMIC.

- realtek,dmic-clk-driving-high : Set the high driving of the DMIC clock out.

- #sound-dai-cells: Should be set to '<1>'.

Pins on the device (for linking into audio routes) for RT5682:

  * DMIC L1
  * DMIC R1
  * IN1P
  * HPOL
  * HPOR

Example:

rt5682 {
	compatible = "realtek,rt5682i";
	reg = <0x1a>;
	interrupt-parent = <&gpio>;
	interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_LEVEL_HIGH>;
	realtek,ldo1-en-gpios =
		<&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
	realtek,dmic1-data-pin = <1>;
	realtek,dmic1-clk-pin = <1>;
	realtek,jd-src = <1>;
	realtek,btndet-delay = <16>;

	#clock-cells = <1>;
	clock-output-names = "rt5682-dai-wclk", "rt5682-dai-bclk";

	clocks = <&osc>;
	clock-names = "mclk";

	AVDD-supply = <&avdd_reg>;
	MICVDD-supply = <&micvdd_reg>;
	DBVDD-supply = <&dbvdd_reg>;
	LDO1-IN-supply = <&ldo1_in_reg>;
};