// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Device tree for the network processing unit (NPU) of the Sophos XGS 87/107
 * firewalls: a Marvell CN9130 SoC with a Marvell 88E6193X switch.
 *
 * The x86 host on the same board is not described here.
 */

/dts-v1/;

#include "cn9130.dtsi"
#include <dt-bindings/gpio/gpio.h>

/ {
	model = "Sophos XGS 107w (CN9130 NPU)";
	compatible = "sophos,xgs107w-npu", "marvell,cn9130";

	chosen {
		stdout-path = "serial0:115200n8";
	};

	aliases {
		ethernet0 = &cp0_eth0;
		i2c1 = &cp0_i2c1;
	};

	memory@0 {
		device_type = "memory";
		reg = <0x0 0x0 0x0 0x80000000>;
	};

	reserved-memory {
		/* OP-TEE, reserved by the firmware */
		tee@4400000 {
			reg = <0x0 0x4400000 0x0 0x1000000>;
			no-map;
		};
	};

	/* Front-panel SFP cage "F1", wired to switch port 9 */
	sfp: sfp {
		compatible = "sff,sfp";
		i2c-bus = <&cp0_i2c1>;
		los-gpios = <&cp0_gpio1 1 GPIO_ACTIVE_HIGH>;
		tx-fault-gpios = <&cp0_gpio1 2 GPIO_ACTIVE_HIGH>;
		mod-def0-gpios = <&cp0_gpio1 3 GPIO_ACTIVE_LOW>;
		tx-disable-gpios = <&cp0_gpio1 7 GPIO_ACTIVE_HIGH>;
	};
};

&uart0 {
	status = "okay";
};

/* eMMC on the AP */
&ap_sdhci0 {
	bus-width = <8>;
	non-removable;
	mmc-ddr-1_8v;
	status = "okay";
};

/*
 * The MPP pin muxing is left as configured by the boot loader; the pin
 * controller node only exists to back the GPIO banks.
 */
&cp0_syscon0 {
	cp0_pinctrl: pinctrl {
		compatible = "marvell,cp115-standalone-pinctrl";
	};
};

&cp0_i2c1 {
	/* I2C bus of the SFP cage */
	clock-frequency = <100000>;
	status = "okay";
};

/* 4 MB SPI NOR with U-Boot and its environment, read-only on purpose */
&cp0_spi0 {
	status = "okay";

	flash@0 {
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-max-frequency = <40000000>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "u-boot";
				reg = <0x0 0x3f0000>;
				read-only;
			};

			partition@3f0000 {
				label = "u-boot-env";
				reg = <0x3f0000 0x10000>;
				read-only;
			};
		};
	};
};

&cp0_ethernet {
	status = "okay";
};

/* 10G link to switch port 0 */
&cp0_eth0 {
	phy-mode = "10gbase-r";
	phys = <&cp0_comphy4 0>;
	managed = "in-band-status";
	status = "okay";
};

&cp0_mdio {
	status = "okay";

	switch@2 {
		compatible = "marvell,mv88e6190";
		reg = <2>;
		reset-gpios = <&cp0_gpio2 17 GPIO_ACTIVE_LOW>;

		ports {
			#address-cells = <1>;
			#size-cells = <0>;

			port@0 {
				reg = <0>;
				ethernet = <&cp0_eth0>;
				phy-mode = "10gbase-r";
				managed = "in-band-status";
			};

			port@1 {
				reg = <1>;
				label = "p1";
			};

			port@2 {
				reg = <2>;
				label = "p2";
			};

			port@3 {
				reg = <3>;
				label = "p3";
			};

			port@4 {
				reg = <4>;
				label = "p4";
			};

			port@5 {
				reg = <5>;
				label = "p5";
			};

			port@6 {
				reg = <6>;
				label = "p6";
			};

			port@7 {
				reg = <7>;
				label = "p7";
			};

			port@8 {
				reg = <8>;
				label = "p8";
			};

			port@9 {
				reg = <9>;
				label = "sfp";
				phy-mode = "1000base-x";
				managed = "in-band-status";
				sfp = <&sfp>;
			};
		};
	};
};