// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* at91-sama5d4ek.dts - Device Tree file for SAMA5D4 Evaluation Kit
*
* Copyright (C) 2014 Atmel,
* 2014 Nicolas Ferre <nicolas.ferre@atmel.com>
*/
/dts-v1/;
#include "sama5d4.dtsi"
/ {
model = "Atmel SAMA5D4-EK";
compatible = "atmel,sama5d4ek", "atmel,sama5d4", "atmel,sama5";
chosen {
stdout-path = "serial0:115200n8";
};
memory@20000000 {
reg = <0x20000000 0x20000000>;
};
clocks {
slow_xtal {
clock-frequency = <32768>;
};
main_xtal {
clock-frequency = <12000000>;
};
};
ahb {
apb {
adc0: adc@fc034000 {
pinctrl-names = "default";
pinctrl-0 = <
/* external trigger conflicts with USBA_VBUS */
&pinctrl_adc0_ad0
&pinctrl_adc0_ad1
&pinctrl_adc0_ad2
&pinctrl_adc0_ad3
&pinctrl_adc0_ad4
>;
/* The vref depends on JP22 of EK. If connect 1-2 then use 3.3V. connect 2-3 use 3.0V */
atmel,adc-vref = <3300>;
/*atmel,adc-ts-wires = <4>;*/ /* Set up ADC touch screen */
status = "okay"; /* Enable ADC IIO support */
};
mmc0: mmc@f8000000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
slot@0 {
reg = <0>;
bus-width = <4>;
cd-gpios = <&pioE 5 0>;
};
};
ssc0: ssc@f8008000 {
status = "okay";
};
spi0: spi@f8010000 {
cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
status = "okay";
flash@0 {
compatible = "atmel,at25df321a";
spi-max-frequency = <50000000>;
reg = <0>;
};
};
i2c0: i2c@f8014000 {
status = "okay";
wm8904: codec@1a {
compatible = "wlf,wm8904";
reg = <0x1a>;
clocks = <&pmc PMC_TYPE_SYSTEM 10>;
clock-names = "mclk";
};
qt1070:keyboard@1b {
compatible = "qt1070";
reg = <0x1b>;
interrupt-parent = <&pioE>;
interrupts = <25 0x0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_qt1070_irq>;
wakeup-source;
};
touchscreen@4c {
compatible = "atmel,maxtouch";
reg = <0x4c>;
interrupt-parent = <&pioE>;
interrupts = <24 0x0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mxt_ts>;
};
};
macb0: ethernet@f8020000 {
pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
phy-mode = "rmii";
status = "okay";
ethernet-phy@1 {
reg = <0x1>;
interrupt-parent = <&pioE>;
interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
};
};
mmc1: mmc@fc000000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
status = "okay";
slot@0 {
reg = <0>;
bus-width = <4>;
cd-gpios = <&pioE 6 0>;
};
};
usart2: serial@fc008000 {
status = "okay";
};
usart3: serial@fc00c000 {
status = "okay";
};
usart4: serial@fc010000 {
status = "okay";
};
tcb2: timer@fc024000 {
timer@0 {
compatible = "atmel,tcb-timer";
reg = <0>;
};
timer@1 {
compatible = "atmel,tcb-timer";
reg = <1>;
};
};
watchdog@fc068640 {
status = "okay";
};
pinctrl@fc06a000 {
board {
pinctrl_macb0_phy_irq: macb0_phy_irq {
atmel,pins =
<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
};
pinctrl_mmc0_cd: mmc0_cd {
atmel,pins =
<AT91_PIOE 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
};
pinctrl_mmc1_cd: mmc1_cd {
atmel,pins =
<AT91_PIOE 6 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
};
pinctrl_pck2_as_audio_mck: pck2_as_audio_mck {
atmel,pins =
<AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>;
};
pinctrl_usba_vbus: usba_vbus {
atmel,pins =
<AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
};
pinctrl_key_gpio: key_gpio_0 {
atmel,pins =
<AT91_PIOE 13 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PE13 gpio */
};
pinctrl_qt1070_irq: qt1070_irq {
atmel,pins =
<AT91_PIOE 25 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
};
pinctrl_mxt_ts: mxt_irq {
atmel,pins =
<AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
};
};
};
};
usb0: gadget@400000 {
atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usba_vbus>;
status = "okay";
};
usb1: ohci@500000 {
num-ports = <3>;
atmel,vbus-gpio = <0 /* &pioE 10 GPIO_ACTIVE_LOW */
&pioE 11 GPIO_ACTIVE_LOW
&pioE 12 GPIO_ACTIVE_LOW
>;
status = "okay";
};
usb2: ehci@600000 {
status = "okay";
};
ebi: ebi@10000000 {
pinctrl-0 = <&pinctrl_ebi_cs3 &pinctrl_ebi_nrd_nandoe
&pinctrl_ebi_nwe_nandwe &pinctrl_ebi_nandrdy
&pinctrl_ebi_data_0_7 &pinctrl_ebi_nand_addr>;
pinctrl-names = "default";
status = "okay";
nand_controller: nand-controller {
status = "okay";
nand@3 {
reg = <0x3 0x0 0x2>;
atmel,rb = <0>;
nand-bus-width = <8>;
nand-ecc-mode = "hw";
nand-on-flash-bbt;
label = "atmel_nand";
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
at91bootstrap@0 {
label = "at91bootstrap";
reg = <0x0 0x40000>;
};
bootloader@40000 {
label = "bootloader";
reg = <0x40000 0x80000>;
};
bootloaderenv@c0000 {
label = "bootloader env";
reg = <0xc0000 0xc0000>;
};
dtb@180000 {
label = "device tree";
reg = <0x180000 0x80000>;
};
kernel@200000 {
label = "kernel";
reg = <0x200000 0x600000>;
};
rootfs@800000 {
label = "rootfs";
reg = <0x800000 0x0f800000>;
};
};
};
};
};
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_key_gpio>;
button {
label = "pb_user1";
gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
linux,code = <0x100>;
wakeup-source;
};
};
leds {
compatible = "gpio-leds";
status = "okay";
led-d8 {
label = "d8";
/* PE28, conflicts with usart4 rts pin */
gpios = <&pioE 28 GPIO_ACTIVE_LOW>;
};
led-d9 {
label = "d9";
gpios = <&pioE 9 GPIO_ACTIVE_HIGH>;
};
led-d10 {
label = "d10";
gpios = <&pioE 8 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
};
};
sound {
compatible = "atmel,asoc-wm8904";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pck2_as_audio_mck>;
atmel,model = "wm8904 @ SAMA5D4EK";
atmel,audio-routing =
"Headphone Jack", "HPOUTL",
"Headphone Jack", "HPOUTR",
"IN1L", "Line In Jack",
"IN1R", "Line In Jack";
atmel,ssc-controller = <&ssc0>;
atmel,audio-codec = <&wm8904>;
};
};