// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* ArmSoM CM5 - Rockchip RK3576 compute module (Raspberry Pi CM4 form factor).
*
* Common to all CM5 carriers. The carrier .dts includes this file, sets the
* board model/compatible, and adds carrier-specific peripherals.
*
* On-module devices:
* - RK806 PMIC on I2C1
* - HYM8563 RTC on I2C2
* - eMMC (SDHCI)
* - GMAC0 + MotorComm YT8531 Gigabit Ethernet PHY (RGMII)
* - SYN43752 WiFi 6 + BT 5.x (SDIO + UART4)
*
* Copyright (c) 2024 ArmSoM
* Copyright (c) 2026 Jiaxing Hu <gahing@gahingwoo.com>
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/rockchip.h>
#include "rk3576.dtsi"
/ {
compatible = "armsom,cm5", "rockchip,rk3576";
vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
compatible = "regulator-fixed";
regulator-name = "vcc_1v1_nldo_s3";
regulator-boot-on;
regulator-always-on;
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
vin-supply = <&vcc_5v0_sys>;
};
vcc_1v2_ufs_vccq_s0: regulator-vcc-1v2-ufs-vccq-s0 {
compatible = "regulator-fixed";
regulator-name = "vcc_1v2_ufs_vccq_s0";
regulator-boot-on;
regulator-always-on;
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
vin-supply = <&vcc_5v0_sys>;
};
vcc_1v8_s0: regulator-vcc-1v8-s0 {
compatible = "regulator-fixed";
regulator-name = "vcc_1v8_s0";
regulator-boot-on;
regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
vin-supply = <&vcc_1v8_s3>;
};
vcc_1v8_ufs_vccq2_s0: regulator-vcc-1v8-ufs-vccq2-s0 {
compatible = "regulator-fixed";
regulator-name = "vcc_1v8_ufs_vccq2_s0";
regulator-boot-on;
regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
vin-supply = <&vcc_1v8_s3>;
};
vcc_2v0_pldo_s3: regulator-vcc-2v0-pldo-s3 {
compatible = "regulator-fixed";
regulator-name = "vcc_2v0_pldo_s3";
regulator-boot-on;
regulator-always-on;
regulator-min-microvolt = <2000000>;
regulator-max-microvolt = <2000000>;
vin-supply = <&vcc_5v0_sys>;
};
vcc_3v3_s0: regulator-vcc-3v3-s0 {
compatible = "regulator-fixed";
regulator-name = "vcc_3v3_s0";
regulator-boot-on;
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vcc_3v3_s3>;
};
vcc_3v3_ufs_s0: regulator-vcc-ufs-s0 {
compatible = "regulator-fixed";
regulator-name = "vcc_3v3_ufs_s0";
regulator-boot-on;
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vcc_5v0_sys>;
};
/*
* WiFi power sequencer for SYN43752. Reset GPIO1 PC6 active-low,
* clock from the HYM8563 RTC oscillator.
*/
sdio_pwrseq: sdio-pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&hym8563>;
clock-names = "ext_clock";
pinctrl-names = "default";
pinctrl-0 = <&wifi_reg_on>;
reset-gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_LOW>;
};
};
&cpu_b0 {
cpu-supply = <&vdd_cpu_big_s0>;
};
&cpu_b1 {
cpu-supply = <&vdd_cpu_big_s0>;
};
&cpu_b2 {
cpu-supply = <&vdd_cpu_big_s0>;
};
&cpu_b3 {
cpu-supply = <&vdd_cpu_big_s0>;
};
&cpu_l0 {
cpu-supply = <&vdd_cpu_lit_s0>;
};
&cpu_l1 {
cpu-supply = <&vdd_cpu_lit_s0>;
};
&cpu_l2 {
cpu-supply = <&vdd_cpu_lit_s0>;
};
&cpu_l3 {
cpu-supply = <&vdd_cpu_lit_s0>;
};
/*
* GMAC0 drives an on-module MotorComm YT8531. The PHY has no local crystal and
* takes the SoC 25 MHz reference (REFCLKO25M_GMAC0_OUT); ethm0_clk0_25m_out
* routes that clock to the pad, and the PHY node consumes and enables it.
*/
&gmac0 {
phy-mode = "rgmii-id";
clock_in_out = "output";
phy-handle = <&rgmii_phy0>;
phy-supply = <&vcc_3v3_s3>;
pinctrl-names = "default";
pinctrl-0 = <ð0m0_miim
ð0m0_tx_bus2
ð0m0_rx_bus2
ð0m0_rgmii_clk
ð0m0_rgmii_bus
ðm0_clk0_25m_out>;
status = "okay";
};
&gpu {
mali-supply = <&vdd_gpu_s0>;
status = "okay";
};
&i2c1 {
status = "okay";
pmic@23 {
compatible = "rockchip,rk806";
reg = <0x23>;
gpio-controller;
#gpio-cells = <2>;
interrupt-parent = <&gpio0>;
interrupts = <RK_PA6 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
<&rk806_dvs2_null>, <&rk806_dvs3_null>;
system-power-controller;
vcc1-supply = <&vcc_5v0_sys>;
vcc2-supply = <&vcc_5v0_sys>;
vcc3-supply = <&vcc_5v0_sys>;
vcc4-supply = <&vcc_5v0_sys>;
vcc5-supply = <&vcc_5v0_sys>;
vcc6-supply = <&vcc_5v0_sys>;
vcc7-supply = <&vcc_5v0_sys>;
vcc8-supply = <&vcc_5v0_sys>;
vcc9-supply = <&vcc_5v0_sys>;
vcc10-supply = <&vcc_5v0_sys>;
vcc11-supply = <&vcc_2v0_pldo_s3>;
vcc12-supply = <&vcc_5v0_sys>;
vcc13-supply = <&vcc_1v1_nldo_s3>;
vcc14-supply = <&vcc_1v1_nldo_s3>;
vcca-supply = <&vcc_5v0_sys>;
rk806_dvs1_null: dvs1-null-pins {
pins = "gpio_pwrctrl1";
function = "pin_fun0";
};
rk806_dvs2_null: dvs2-null-pins {
pins = "gpio_pwrctrl2";
function = "pin_fun0";
};
rk806_dvs3_null: dvs3-null-pins {
pins = "gpio_pwrctrl3";
function = "pin_fun0";
};
regulators {
vdd_cpu_big_s0: dcdc-reg1 {
regulator-always-on;
regulator-boot-on;
regulator-enable-ramp-delay = <400>;
regulator-min-microvolt = <550000>;
regulator-max-microvolt = <950000>;
regulator-name = "vdd_cpu_big_s0";
regulator-ramp-delay = <12500>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdd_npu_s0: dcdc-reg2 {
regulator-boot-on;
regulator-enable-ramp-delay = <400>;
regulator-min-microvolt = <550000>;
regulator-max-microvolt = <950000>;
regulator-name = "vdd_npu_s0";
regulator-ramp-delay = <12500>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdd_cpu_lit_s0: dcdc-reg3 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <550000>;
regulator-max-microvolt = <950000>;
regulator-name = "vdd_cpu_lit_s0";
regulator-ramp-delay = <12500>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc_3v3_s3: dcdc-reg4 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc_3v3_s3";
regulator-state-mem {
regulator-on-in-suspend;
};
};
vdd_gpu_s0: dcdc-reg5 {
regulator-boot-on;
regulator-enable-ramp-delay = <400>;
regulator-min-microvolt = <550000>;
regulator-max-microvolt = <900000>;
regulator-ramp-delay = <12500>;
regulator-name = "vdd_gpu_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vddq_ddr_s0: dcdc-reg6 {
regulator-always-on;
regulator-boot-on;
regulator-name = "vddq_ddr_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdd_logic_s0: dcdc-reg7 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <550000>;
regulator-max-microvolt = <800000>;
regulator-name = "vdd_logic_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc_1v8_s3: dcdc-reg8 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc_1v8_s3";
regulator-state-mem {
regulator-on-in-suspend;
};
};
vdd2_ddr_s3: dcdc-reg9 {
regulator-always-on;
regulator-boot-on;
regulator-name = "vdd2_ddr_s3";
regulator-state-mem {
regulator-on-in-suspend;
};
};
vdd_ddr_s0: dcdc-reg10 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <550000>;
regulator-max-microvolt = <1200000>;
regulator-name = "vdd_ddr_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcca_1v8_s0: pldo-reg1 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcca_1v8_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcca1v8_pldo2_s0: pldo-reg2 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcca1v8_pldo2_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdda_1v2_s0: pldo-reg3 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-name = "vdda_1v2_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcca_3v3_s0: pldo-reg4 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcca_3v3_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vccio_sd_s0: pldo-reg5 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vccio_sd_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcca1v8_pldo6_s3: pldo-reg6 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcca1v8_pldo6_s3";
regulator-state-mem {
regulator-on-in-suspend;
};
};
vdd_0v75_s3: nldo-reg1 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <750000>;
regulator-name = "vdd_0v75_s3";
regulator-state-mem {
regulator-on-in-suspend;
};
};
vdda_ddr_pll_s0: nldo-reg2 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <850000>;
regulator-name = "vdda_ddr_pll_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdda0v75_hdmi_s0: nldo-reg3 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <837500>;
regulator-max-microvolt = <837500>;
regulator-name = "vdda0v75_hdmi_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdda_0v85_s0: nldo-reg4 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <850000>;
regulator-name = "vdda_0v85_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdda_0v75_s0: nldo-reg5 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <750000>;
regulator-name = "vdda_0v75_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
};
};
};
/* I2C2: HYM8563 RTC @ 0x51 (interrupt on GPIO0 PA0). */
&i2c2 {
status = "okay";
hym8563: rtc@51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
#clock-cells = <0>;
clock-output-names = "hym8563";
interrupt-parent = <&gpio0>;
interrupts = <RK_PA0 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&hym8563_int>;
wakeup-source;
};
};
/*
* The PHY reset has to be described at the MDIO bus level: mdiobus releases a
* bus level reset before it scans for PHY IDs, whereas the per-PHY reset-gpios
* is only applied by phylib once the PHY has already been found, which never
* happens while the YT8531 is still held in reset.
*
* The compatible names the YT8531 explicitly so phylib instantiates the PHY
* from the device tree without an MDIO ID probe; the crystal-less PHY does not
* answer on MDIO until its driver has enabled the reference clock below.
*/
&mdio0 {
reset-gpios = <&gpio2 RK_PB3 GPIO_ACTIVE_LOW>;
reset-delay-us = <20000>;
reset-post-delay-us = <100000>;
rgmii_phy0: ethernet-phy@1 {
compatible = "ethernet-phy-id4f51.e91b";
reg = <0x1>;
clocks = <&cru REFCLKO25M_GMAC0_OUT>;
};
};
&saradc {
vref-supply = <&vcca_1v8_s0>;
status = "okay";
};
/* eMMC: on-module, HS400 200 MHz with enhanced strobe. */
&sdhci {
bus-width = <8>;
full-pwr-cycle-in-suspend;
max-frequency = <200000000>;
mmc-hs400-1_8v;
mmc-hs400-enhanced-strobe;
no-sdio;
no-sd;
non-removable;
/delete-property/ supports-cqe;
status = "okay";
};
/* SDIO: SYN43752 WiFi, power-sequenced by sdio_pwrseq, clock from HYM8563. */
&sdio {
bus-width = <4>;
cap-sdio-irq;
disable-wp;
keep-power-in-suspend;
mmc-pwrseq = <&sdio_pwrseq>;
no-sd;
no-mmc;
non-removable;
sd-uhs-sdr50;
sd-uhs-sdr104;
vmmc-supply = <&vcc_3v3_s3>;
vqmmc-supply = <&vcc_1v8_s3>;
wakeup-source;
status = "okay";
};
/* UART4: Bluetooth (SYN43752). */
&uart4 {
pinctrl-0 = <&uart4m1_xfer &uart4m1_ctsn &uart4m1_rtsn>;
pinctrl-names = "default";
uart-has-rtscts;
status = "okay";
};
&pinctrl {
hym8563 {
hym8563_int: hym8563-int {
rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
wireless-wlan {
/* GPIO1 PC6 - WiFi power enable / reset (sdio_pwrseq) */
wifi_reg_on: wifi-reg-on {
rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
};