Directory Files
.. 48
File Size
.cfg80211.o.cmd 74 kB
.debug.o.cmd 75 kB
.debugfs.o.cmd 76 kB
.ethtool.o.cmd 75 kB
.fw.o.cmd 74 kB
.interrupt.o.cmd 75 kB
.main.o.cmd 75 kB
.modules.order.cmd 166 B
.netdev.o.cmd 75 kB
.p2p.o.cmd 74 kB
.pcie_bus.o.cmd 76 kB
.pm.o.cmd 74 kB
.pmc.o.cmd 75 kB
.rx_reorder.o.cmd 75 kB
.trace.o.cmd 77 kB
.txrx.o.cmd 76 kB
.txrx_edma.o.cmd 76 kB
.wil6210.ko.cmd 351 B
.wil6210.mod.cmd 366 B
.wil6210.mod.o.cmd 50 kB
.wil6210.o.cmd 537 B
.wil_crash_dump.o.cmd 74 kB
.wil_platform.o.cmd 51 kB
.wmi.o.cmd 75 kB
Kconfig 1.7 kB
Makefile 608 B
boot_loader.h 2.2 kB
cfg80211.c 90 kB
cfg80211.o 394 kB
debug.c 1.5 kB
debug.o 27 kB
debugfs.c 64 kB
debugfs.o 292 kB
ethtool.c 2.9 kB
ethtool.o 18 kB
fw.c 680 B
fw.h 6.6 kB
fw.o 93 kB
fw_inc.c 22 kB
interrupt.c 25 kB
interrupt.o 123 kB
main.c 53 kB
main.o 243 kB
modules.order 43 B
netdev.c 13 kB
netdev.o 88 kB
p2p.c 8.9 kB
p2p.o 42 kB
pcie_bus.c 17 kB
pcie_bus.o 85 kB
pm.c 11 kB
pm.o 72 kB
pmc.c 11 kB
pmc.h 607 B
pmc.o 51 kB
rx_reorder.c 10 kB
rx_reorder.o 54 kB
trace.c 159 B
trace.h 7.6 kB
trace.o 152 kB
txrx.c 71 kB
txrx.h 21 kB
txrx.o 321 kB
txrx_edma.c 44 kB
txrx_edma.h 19 kB
txrx_edma.o 220 kB
wil6210.h 50 kB
wil6210.ko 3.5 MB
wil6210.mod 805 B
wil6210.mod.c 623 B
wil6210.mod.o 3.6 kB
wil6210.o 3.6 MB
wil_crash_dump.c 2.8 kB
wil_crash_dump.o 21 kB
wil_platform.c 822 B
wil_platform.h 2.5 kB
wil_platform.o 6.9 kB
wmi.c 113 kB
wmi.h 108 kB
wmi.o 472 kB

Linux v7.4-rc3 - wil6210

# SPDX-License-Identifier: ISC
config WIL6210
	tristate "Wilocity 60g WiFi card wil6210 support"
	select WANT_DEV_COREDUMP
	select CRC32
	depends on CFG80211
	depends on PCI
	default n
	help
	  This module adds support for wireless adapter based on
	  wil6210 chip by Wilocity. It supports operation on the
	  60 GHz band, covered by the IEEE802.11ad standard.

	  https://wireless.wiki.kernel.org/en/users/Drivers/wil6210

	  If you choose to build it as a module, it will be called
	  wil6210

config WIL6210_ISR_COR
	bool "Use Clear-On-Read mode for ISR registers for wil6210"
	depends on WIL6210
	default y
	help
	  ISR registers on wil6210 chip may operate in either
	  COR (Clear-On-Read) or W1C (Write-1-to-Clear) mode.
	  For production code, use COR (say y); is default since
	  it saves extra target transaction;
	  For ISR debug, use W1C (say n); is allows to monitor ISR
	  registers with debugfs. If COR were used, ISR would
	  self-clear when accessed for debug purposes, it makes
	  such monitoring impossible.
	  Say y unless you debug interrupts

config WIL6210_TRACING
	bool "wil6210 tracing support"
	depends on WIL6210
	depends on EVENT_TRACING
	default n
	help
	  Say Y here to enable tracepoints for the wil6210 driver
	  using the kernel tracing infrastructure.  Select this
	  option if you are interested in debugging the driver.

	  If unsure, say Y to make it easier to debug problems.

config WIL6210_DEBUGFS
	bool "wil6210 debugfs support"
	depends on WIL6210
	depends on DEBUG_FS
	default y
	help
	  Say Y here to enable wil6210 debugfs support, using the
	  kernel debugfs infrastructure. Select this
	  option if you are interested in debugging the driver.

	  If unsure, say Y to make it easier to debug problems.