/*
 * Copyright (c) 2017 MediaTek Inc.
 * Author: Ming Huang <ming.huang@mediatek.com>
 *	   Sean Wang <sean.wang@mediatek.com>
 *
 * SPDX-License-Identifier: (GPL-2.0 OR MIT)
 */

/dts-v1/;
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>

#include "mt7622.dtsi"
#include "mt6380.dtsi"

/ {
	model = "MediaTek MT7622 RFB1 board";
	chassis-type = "embedded";
	compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622";

	aliases {
		serial0 = &uart0;
	};

	chosen {
		stdout-path = "serial0:115200n8";
		bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512";
	};

	cpus {
		cpu@0 {
			proc-supply = <&mt6380_vcpu_reg>;
			sram-supply = <&mt6380_vm_reg>;
		};

		cpu@1 {
			proc-supply = <&mt6380_vcpu_reg>;
			sram-supply = <&mt6380_vm_reg>;
		};
	};

	gpio-keys {
		compatible = "gpio-keys";

		key-factory {
			label = "factory";
			linux,code = <BTN_0>;
			gpios = <&pio 0 0>;
		};

		key-wps {
			label = "wps";
			linux,code = <KEY_WPS_BUTTON>;
			gpios = <&pio 102 0>;
		};
	};

	memory {
		reg = <0 0x40000000 0 0x20000000>;
	};

	reg_1p8v: regulator-1p8v {
		compatible = "regulator-fixed";
		regulator-name = "fixed-1.8V";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		regulator-always-on;
	};

	reg_3p3v: regulator-3p3v {
		compatible = "regulator-fixed";
		regulator-name = "fixed-3.3V";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		regulator-boot-on;
		regulator-always-on;
	};

	reg_5v: regulator-5v {
		compatible = "regulator-fixed";
		regulator-name = "fixed-5V";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		regulator-boot-on;
		regulator-always-on;
	};
};

&bch {
	status = "disabled";
};

&btif {
	status = "okay";
};

&cir {
	pinctrl-names = "default";
	pinctrl-0 = <&irrx_pins>;
	status = "okay";
};

&eth {
	pinctrl-names = "default";
	pinctrl-0 = <&eth_pins>;
	status = "okay";

	gmac0: mac@0 {
		compatible = "mediatek,eth-mac";
		reg = <0>;
		phy-mode = "2500base-x";

		fixed-link {
			speed = <2500>;
			full-duplex;
			pause;
		};
	};

	mdio-bus {
		#address-cells = <1>;
		#size-cells = <0>;

		switch@0 {
			compatible = "mediatek,mt7531";
			reg = <0>;
			reset-gpios = <&pio 54 0>;

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					label = "lan0";
				};

				port@1 {
					reg = <1>;
					label = "lan1";
				};

				port@2 {
					reg = <2>;
					label = "lan2";
				};

				port@3 {
					reg = <3>;
					label = "lan3";
				};

				port@4 {
					reg = <4>;
					label = "wan";
				};

				port@6 {
					reg = <6>;
					label = "cpu";
					ethernet = <&gmac0>;
					phy-mode = "2500base-x";

					fixed-link {
						speed = <2500>;
						full-duplex;
						pause;
					};
				};
			};
		};

	};
};

&i2c1 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c1_pins>;
	status = "okay";
};

&i2c2 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c2_pins>;
	status = "okay";
};

&mmc0 {
	pinctrl-names = "default", "state_uhs";
	pinctrl-0 = <&emmc_pins_default>;
	pinctrl-1 = <&emmc_pins_uhs>;
	status = "okay";
	bus-width = <8>;
	max-frequency = <50000000>;
	cap-mmc-highspeed;
	mmc-hs200-1_8v;
	vmmc-supply = <&reg_3p3v>;
	vqmmc-supply = <&reg_1p8v>;
	assigned-clocks = <&topckgen CLK_TOP_MSDC30_0_SEL>;
	assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
	non-removable;
};

&mmc1 {
	pinctrl-names = "default", "state_uhs";
	pinctrl-0 = <&sd0_pins_default>;
	pinctrl-1 = <&sd0_pins_uhs>;
	status = "okay";
	bus-width = <4>;
	max-frequency = <50000000>;
	cap-sd-highspeed;
	cd-gpios = <&pio 81 GPIO_ACTIVE_LOW>;
	vmmc-supply = <&reg_3p3v>;
	vqmmc-supply = <&reg_3p3v>;
	assigned-clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>;
	assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
};

&nandc {
	pinctrl-names = "default";
	pinctrl-0 = <&parallel_nand_pins>;
	status = "disabled";
};

&nor_flash {
	pinctrl-names = "default";
	pinctrl-0 = <&spi_nor_pins>;
	status = "disabled";

	flash@0 {
		compatible = "jedec,spi-nor";
		reg = <0>;
	};
};

&pcie0 {
	pinctrl-names = "default";
	pinctrl-0 = <&pcie0_pins>;
	status = "okay";
};

&pio {
	/* eMMC is shared pin with parallel NAND */
	emmc_pins_default: emmc-pins-default {
		mux {
			function = "emmc", "emmc_rst";
			groups = "emmc";
		};

		/* "NDL0","NDL1","NDL2","NDL3","NDL4","NDL5","NDL6","NDL7",
		 * "NRB","NCLE" pins are used as DAT0,DAT1,DAT2,DAT3,DAT4,
		 * DAT5,DAT6,DAT7,CMD,CLK for eMMC respectively
		 */
		conf-cmd-dat {
			pins = "NDL0", "NDL1", "NDL2",
			       "NDL3", "NDL4", "NDL5",
			       "NDL6", "NDL7", "NRB";
			input-enable;
			bias-pull-up;
		};

		conf-clk {
			pins = "NCLE";
			bias-pull-down;
		};
	};

	emmc_pins_uhs: emmc-pins-uhs {
		mux {
			function = "emmc";
			groups = "emmc";
		};

		conf-cmd-dat {
			pins = "NDL0", "NDL1", "NDL2",
			       "NDL3", "NDL4", "NDL5",
			       "NDL6", "NDL7", "NRB";
			input-enable;
			drive-strength = <4>;
			bias-pull-up;
		};

		conf-clk {
			pins = "NCLE";
			drive-strength = <4>;
			bias-pull-down;
		};
	};

	eth_pins: eth-pins {
		mux {
			function = "eth";
			groups = "mdc_mdio", "rgmii_via_gmac2";
		};
	};

	i2c1_pins: i2c1-pins {
		mux {
			function = "i2c";
			groups = "i2c1_0";
		};
	};

	i2c2_pins: i2c2-pins {
		mux {
			function = "i2c";
			groups = "i2c2_0";
		};
	};

	i2s1_pins: i2s1-pins {
		mux {
			function = "i2s";
			groups =  "i2s_out_mclk_bclk_ws",
				  "i2s1_in_data",
				  "i2s1_out_data";
		};

		conf {
			pins = "I2S1_IN", "I2S1_OUT", "I2S_BCLK",
			       "I2S_WS", "I2S_MCLK";
			drive-strength = <12>;
			bias-pull-down;
		};
	};

	irrx_pins: irrx-pins {
		mux {
			function = "ir";
			groups = "ir_1_rx";
		};
	};

	irtx_pins: irtx-pins {
		mux {
			function = "ir";
			groups = "ir_1_tx";
		};
	};

	/* Parallel nand is shared pin with eMMC */
	parallel_nand_pins: parallel-nand-pins {
		mux {
			function = "flash";
			groups = "par_nand";
		};
	};

	pcie0_pins: pcie0-pins {
		mux {
			function = "pcie";
			groups = "pcie0_pad_perst",
				 "pcie0_1_waken",
				 "pcie0_1_clkreq";
		};
	};

	pcie1_pins: pcie1-pins {
		mux {
			function = "pcie";
			groups = "pcie1_pad_perst",
				 "pcie1_0_waken",
				 "pcie1_0_clkreq";
		};
	};

	pmic_bus_pins: pmic-bus-pins {
		mux {
			function = "pmic";
			groups = "pmic_bus";
		};
	};

	pwm7_pins: pwm1-2-pins {
		mux {
			function = "pwm";
			groups = "pwm_ch7_2";
		};
	};

	wled_pins: wled-pins {
		mux {
			function = "led";
			groups = "wled";
		};
	};

	sd0_pins_default: sd0-pins-default {
		mux {
			function = "sd";
			groups = "sd_0";
		};

		/* "I2S2_OUT, "I2S4_IN"", "I2S3_IN", "I2S2_IN",
		 *  "I2S4_OUT", "I2S3_OUT" are used as DAT0, DAT1,
		 *  DAT2, DAT3, CMD, CLK for SD respectively.
		 */
		conf-cmd-data {
			pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
			       "I2S2_IN","I2S4_OUT";
			input-enable;
			drive-strength = <8>;
			bias-pull-up;
		};
		conf-clk {
			pins = "I2S3_OUT";
			drive-strength = <12>;
			bias-pull-down;
		};
		conf-cd {
			pins = "TXD3";
			bias-pull-up;
		};
	};

	sd0_pins_uhs: sd0-pins-uhs {
		mux {
			function = "sd";
			groups = "sd_0";
		};

		conf-cmd-data {
			pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
			       "I2S2_IN","I2S4_OUT";
			input-enable;
			bias-pull-up;
		};

		conf-clk {
			pins = "I2S3_OUT";
			bias-pull-down;
		};
	};

	/* Serial NAND is shared pin with SPI-NOR */
	serial_nand_pins: serial-nand-pins {
		mux {
			function = "flash";
			groups = "snfi";
		};
	};

	spic0_pins: spic0-pins {
		mux {
			function = "spi";
			groups = "spic0_0";
		};
	};

	spic1_pins: spic1-pins {
		mux {
			function = "spi";
			groups = "spic1_0";
		};
	};

	/* SPI-NOR is shared pin with serial NAND */
	spi_nor_pins: spi-nor-pins {
		mux {
			function = "flash";
			groups = "spi_nor";
		};
	};

	/* serial NAND is shared pin with SPI-NOR */
	serial_nand_pins: serial-nand-pins {
		mux {
			function = "flash";
			groups = "snfi";
		};
	};

	uart0_pins: uart0-pins {
		mux {
			function = "uart";
			groups = "uart0_0_tx_rx" ;
		};
	};

	uart2_pins: uart2-pins {
		mux {
			function = "uart";
			groups = "uart2_1_tx_rx" ;
		};
	};

	watchdog_pins: watchdog-pins {
		mux {
			function = "watchdog";
			groups = "watchdog";
		};
	};

	wmac_pins: wmac-pins {
		mux {
			function = "antsel";
			groups = "antsel0", "antsel1", "antsel2", "antsel3",
				 "antsel4", "antsel5", "antsel6", "antsel7",
				 "antsel8", "antsel9", "antsel12", "antsel13",
				 "antsel14", "antsel15", "antsel16", "antsel17";
		};
	};
};

&pwm {
	pinctrl-names = "default";
	pinctrl-0 = <&pwm7_pins>;
	status = "okay";
};

&pwrap {
	pinctrl-names = "default";
	pinctrl-0 = <&pmic_bus_pins>;

	status = "okay";
};

&sata {
	status = "okay";
};

&sata_phy {
	status = "okay";
};

&spi0 {
	pinctrl-names = "default";
	pinctrl-0 = <&spic0_pins>;
	status = "okay";
};

&spi1 {
	pinctrl-names = "default";
	pinctrl-0 = <&spic1_pins>;
	status = "okay";
};

&ssusb {
	vusb33-supply = <&reg_3p3v>;
	vbus-supply = <&reg_5v>;
	status = "okay";
};

&u3phy {
	status = "okay";
};

&uart0 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart0_pins>;
	status = "okay";
};

&uart2 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart2_pins>;
	status = "okay";
};

&watchdog {
	pinctrl-names = "default";
	pinctrl-0 = <&watchdog_pins>;
	status = "okay";
};

&wmac {
	pinctrl-names = "default";
	pinctrl-0 = <&wmac_pins>;
	status = "okay";
};