// SPDX-License-Identifier: GPL-2.0-or-later
// Copyright 2019 IBM Corp.
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/aspeed-scu-ic.h>
#include <dt-bindings/clock/ast2600-clock.h>
/ {
model = "Aspeed BMC";
compatible = "aspeed,ast2600";
#address-cells = <1>;
#size-cells = <1>;
interrupt-parent = <&gic>;
aliases {
i2c0 = &i2c0;
i2c1 = &i2c1;
i2c2 = &i2c2;
i2c3 = &i2c3;
i2c4 = &i2c4;
i2c5 = &i2c5;
i2c6 = &i2c6;
i2c7 = &i2c7;
i2c8 = &i2c8;
i2c9 = &i2c9;
i2c10 = &i2c10;
i2c11 = &i2c11;
i2c12 = &i2c12;
i2c13 = &i2c13;
i2c14 = &i2c14;
i2c15 = &i2c15;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
serial3 = &uart4;
serial4 = &uart5;
serial5 = &vuart1;
serial6 = &vuart2;
mdio0 = &mdio0;
mdio1 = &mdio1;
mdio2 = &mdio2;
mdio3 = &mdio3;
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
enable-method = "aspeed,ast2600-smp";
cpu@f00 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <0xf00>;
};
cpu@f01 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <0xf01>;
};
};
timer {
compatible = "arm,armv7-timer";
interrupt-parent = <&gic>;
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
clocks = <&syscon ASPEED_CLK_HPLL>;
arm,cpu-registers-not-fw-configured;
always-on;
};
edac: sdram@1e6e0000 {
compatible = "aspeed,ast2600-sdram-edac", "syscon";
reg = <0x1e6e0000 0x174>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
};
ahb {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
ranges;
gic: interrupt-controller@40461000 {
compatible = "arm,cortex-a7-gic";
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
#interrupt-cells = <3>;
interrupt-controller;
interrupt-parent = <&gic>;
reg = <0x40461000 0x1000>,
<0x40462000 0x1000>,
<0x40464000 0x2000>,
<0x40466000 0x2000>;
};
ahbc: bus@1e600000 {
compatible = "aspeed,ast2600-ahbc", "syscon";
reg = <0x1e600000 0x100>;
};
fmc: spi@1e620000 {
reg = <0x1e620000 0xc4>, <0x20000000 0x10000000>;
#address-cells = <1>;
#size-cells = <0>;
compatible = "aspeed,ast2600-fmc";
clocks = <&syscon ASPEED_CLK_AHB>;
status = "disabled";
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
flash@0 {
reg = < 0 >;
compatible = "jedec,spi-nor";
spi-max-frequency = <50000000>;
spi-rx-bus-width = <2>;
status = "disabled";
};
flash@1 {
reg = < 1 >;
compatible = "jedec,spi-nor";
spi-max-frequency = <50000000>;
spi-rx-bus-width = <2>;
status = "disabled";
};
flash@2 {
reg = < 2 >;
compatible = "jedec,spi-nor";
spi-max-frequency = <50000000>;
spi-rx-bus-width = <2>;
status = "disabled";
};
};
spi1: spi@1e630000 {
reg = <0x1e630000 0xc4>, <0x30000000 0x10000000>;
#address-cells = <1>;
#size-cells = <0>;
compatible = "aspeed,ast2600-spi";
clocks = <&syscon ASPEED_CLK_AHB>;
status = "disabled";
flash@0 {
reg = < 0 >;
compatible = "jedec,spi-nor";
spi-max-frequency = <50000000>;
spi-rx-bus-width = <2>;
status = "disabled";
};
flash@1 {
reg = < 1 >;
compatible = "jedec,spi-nor";
spi-max-frequency = <50000000>;
spi-rx-bus-width = <2>;
status = "disabled";
};
};
spi2: spi@1e631000 {
reg = <0x1e631000 0xc4>, <0x50000000 0x10000000>;
#address-cells = <1>;
#size-cells = <0>;
compatible = "aspeed,ast2600-spi";
clocks = <&syscon ASPEED_CLK_AHB>;
status = "disabled";
flash@0 {
reg = < 0 >;
compatible = "jedec,spi-nor";
spi-max-frequency = <50000000>;
spi-rx-bus-width = <2>;
status = "disabled";
};
flash@1 {
reg = < 1 >;
compatible = "jedec,spi-nor";
spi-max-frequency = <50000000>;
spi-rx-bus-width = <2>;
status = "disabled";
};
flash@2 {
reg = < 2 >;
compatible = "jedec,spi-nor";
spi-max-frequency = <50000000>;
spi-rx-bus-width = <2>;
status = "disabled";
};
};
mdio0: mdio@1e650000 {
compatible = "aspeed,ast2600-mdio";
reg = <0x1e650000 0x8>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mdio1_default>;
resets = <&syscon ASPEED_RESET_MII>;
};
mdio1: mdio@1e650008 {
compatible = "aspeed,ast2600-mdio";
reg = <0x1e650008 0x8>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mdio2_default>;
resets = <&syscon ASPEED_RESET_MII>;
};
mdio2: mdio@1e650010 {
compatible = "aspeed,ast2600-mdio";
reg = <0x1e650010 0x8>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mdio3_default>;
resets = <&syscon ASPEED_RESET_MII>;
};
mdio3: mdio@1e650018 {
compatible = "aspeed,ast2600-mdio";
reg = <0x1e650018 0x8>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mdio4_default>;
resets = <&syscon ASPEED_RESET_MII>;
};
mac0: ftgmac@1e660000 {
compatible = "aspeed,ast2600-mac", "faraday,ftgmac100";
reg = <0x1e660000 0x180>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>;
status = "disabled";
};
mac1: ftgmac@1e680000 {
compatible = "aspeed,ast2600-mac", "faraday,ftgmac100";
reg = <0x1e680000 0x180>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_MAC2CLK>;
status = "disabled";
};
mac2: ftgmac@1e670000 {
compatible = "aspeed,ast2600-mac", "faraday,ftgmac100";
reg = <0x1e670000 0x180>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>;
status = "disabled";
};
mac3: ftgmac@1e690000 {
compatible = "aspeed,ast2600-mac", "faraday,ftgmac100";
reg = <0x1e690000 0x180>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>;
status = "disabled";
};
ehci0: usb@1e6a1000 {
compatible = "aspeed,ast2600-ehci", "generic-ehci";
reg = <0x1e6a1000 0x100>;
interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb2ah_default>;
status = "disabled";
};
ehci1: usb@1e6a3000 {
compatible = "aspeed,ast2600-ehci", "generic-ehci";
reg = <0x1e6a3000 0x100>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb2bh_default>;
status = "disabled";
};
uhci: usb@1e6b0000 {
compatible = "aspeed,ast2600-uhci", "generic-uhci";
reg = <0x1e6b0000 0x100>;
interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
#ports = <2>;
clocks = <&syscon ASPEED_CLK_GATE_USBUHCICLK>;
status = "disabled";
/*
* No default pinmux, it will follow EHCI, use an
* explicit pinmux override if EHCI is not enabled.
*/
};
vhub: usb-vhub@1e6a0000 {
compatible = "aspeed,ast2600-usb-vhub";
reg = <0x1e6a0000 0x350>;
interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
aspeed,vhub-downstream-ports = <7>;
aspeed,vhub-generic-endpoints = <21>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb2ad_default>;
status = "disabled";
};
udc: usb@1e6a2000 {
compatible = "aspeed,ast2600-udc";
reg = <0x1e6a2000 0x300>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb2bd_default>;
status = "disabled";
};
apb {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
hace: crypto@1e6d0000 {
compatible = "aspeed,ast2600-hace";
reg = <0x1e6d0000 0x200>;
interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_YCLK>;
resets = <&syscon ASPEED_RESET_HACE>;
};
syscon: syscon@1e6e2000 {
compatible = "aspeed,ast2600-scu", "syscon", "simple-mfd";
reg = <0x1e6e2000 0x1000>;
ranges = <0 0x1e6e2000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
#clock-cells = <1>;
#reset-cells = <1>;
pinctrl: pinctrl {
compatible = "aspeed,ast2600-pinctrl";
};
silicon-id@14 {
compatible = "aspeed,ast2600-silicon-id", "aspeed,silicon-id";
reg = <0x14 0x4 0x5b0 0x8>;
};
smp-memram@180 {
compatible = "aspeed,ast2600-smpmem";
reg = <0x180 0x40>;
};
scu_ic0: interrupt-controller@560 {
#interrupt-cells = <1>;
compatible = "aspeed,ast2600-scu-ic0";
reg = <0x560 0x4>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
interrupt-controller;
};
scu_ic1: interrupt-controller@570 {
#interrupt-cells = <1>;
compatible = "aspeed,ast2600-scu-ic1";
reg = <0x570 0x4>;
interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
interrupt-controller;
};
};
rng: hwrng@1e6e2524 {
compatible = "timeriomem_rng";
reg = <0x1e6e2524 0x4>;
period = <1>;
quality = <100>;
};
gfx: display@1e6e6000 {
compatible = "aspeed,ast2600-gfx", "syscon";
reg = <0x1e6e6000 0x1000>;
reg-io-width = <4>;
clocks = <&syscon ASPEED_CLK_GATE_D1CLK>;
resets = <&syscon ASPEED_RESET_GRAPHICS>;
syscon = <&syscon>;
status = "disabled";
interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
};
xdma: xdma@1e6e7000 {
compatible = "aspeed,ast2600-xdma";
reg = <0x1e6e7000 0x100>;
clocks = <&syscon ASPEED_CLK_GATE_BCLK>;
resets = <&syscon ASPEED_RESET_DEV_XDMA>, <&syscon ASPEED_RESET_RC_XDMA>;
reset-names = "device", "root-complex";
interrupts-extended = <&gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
<&scu_ic0 ASPEED_AST2600_SCU_IC0_PCIE_PERST_LO_TO_HI>;
aspeed,pcie-device = "bmc";
aspeed,scu = <&syscon>;
status = "disabled";
};
adc0: adc@1e6e9000 {
compatible = "aspeed,ast2600-adc0";
reg = <0x1e6e9000 0x100>;
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_ADC>;
interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
#io-channel-cells = <1>;
status = "disabled";
};
adc1: adc@1e6e9100 {
compatible = "aspeed,ast2600-adc1";
reg = <0x1e6e9100 0x100>;
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_ADC>;
interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
#io-channel-cells = <1>;
status = "disabled";
};
sbc: secure-boot-controller@1e6f2000 {
compatible = "aspeed,ast2600-sbc";
reg = <0x1e6f2000 0x1000>;
};
acry: crypto@1e6fa000 {
compatible = "aspeed,ast2600-acry";
reg = <0x1e6fa000 0x400>, <0x1e710000 0x1800>;
interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_RSACLK>;
aspeed,ahbc = <&ahbc>;
};
video: video@1e700000 {
compatible = "aspeed,ast2600-video-engine";
reg = <0x1e700000 0x1000>;
clocks = <&syscon ASPEED_CLK_GATE_VCLK>,
<&syscon ASPEED_CLK_GATE_ECLK>;
clock-names = "vclk", "eclk";
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
gpio0: gpio@1e780000 {
#gpio-cells = <2>;
gpio-controller;
compatible = "aspeed,ast2600-gpio";
reg = <0x1e780000 0x400>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
gpio-ranges = <&pinctrl 0 0 208>;
ngpios = <208>;
clocks = <&syscon ASPEED_CLK_APB2>;
interrupt-controller;
#interrupt-cells = <2>;
};
sgpiom0: sgpiom@1e780500 {
#gpio-cells = <2>;
gpio-controller;
compatible = "aspeed,ast2600-sgpiom";
reg = <0x1e780500 0x100>;
interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_APB2>;
interrupt-controller;
bus-frequency = <12000000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sgpm1_default>;
status = "disabled";
};
sgpiom1: sgpiom@1e780600 {
#gpio-cells = <2>;
gpio-controller;
compatible = "aspeed,ast2600-sgpiom";
reg = <0x1e780600 0x100>;
interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_APB2>;
interrupt-controller;
bus-frequency = <12000000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sgpm2_default>;
status = "disabled";
};
gpio1: gpio@1e780800 {
#gpio-cells = <2>;
gpio-controller;
compatible = "aspeed,ast2600-gpio";
reg = <0x1e780800 0x800>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
gpio-ranges = <&pinctrl 0 208 36>;
ngpios = <36>;
clocks = <&syscon ASPEED_CLK_APB1>;
interrupt-controller;
#interrupt-cells = <2>;
};
rtc: rtc@1e781000 {
compatible = "aspeed,ast2600-rtc";
reg = <0x1e781000 0x18>;
interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
timer: timer@1e782000 {
compatible = "aspeed,ast2600-timer";
reg = <0x1e782000 0x90>;
interrupts-extended = <&gic GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
<&gic GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
<&gic GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
<&gic GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
<&gic GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
<&gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
<&gic GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
<&gic GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_APB1>;
clock-names = "PCLK";
status = "disabled";
};
uart1: serial@1e783000 {
compatible = "ns16550a";
reg = <0x1e783000 0x20>;
reg-shift = <2>;
reg-io-width = <4>;
interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_UART1CLK>;
resets = <&lpc_reset 4>;
no-loopback-test;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_txd1_default &pinctrl_rxd1_default>;
status = "disabled";
};
uart5: serial@1e784000 {
compatible = "ns16550a";
reg = <0x1e784000 0x1000>;
reg-shift = <2>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_UART5CLK>;
no-loopback-test;
};
wdt1: watchdog@1e785000 {
compatible = "aspeed,ast2600-wdt";
reg = <0x1e785000 0x40>;
};
wdt2: watchdog@1e785040 {
compatible = "aspeed,ast2600-wdt";
reg = <0x1e785040 0x40>;
status = "disabled";
};
wdt3: watchdog@1e785080 {
compatible = "aspeed,ast2600-wdt";
reg = <0x1e785080 0x40>;
status = "disabled";
};
wdt4: watchdog@1e7850c0 {
compatible = "aspeed,ast2600-wdt";
reg = <0x1e7850C0 0x40>;
status = "disabled";
};
peci0: peci-controller@1e78b000 {
compatible = "aspeed,ast2600-peci";
reg = <0x1e78b000 0x100>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_REF0CLK>;
resets = <&syscon ASPEED_RESET_PECI>;
cmd-timeout-ms = <1000>;
clock-frequency = <1000000>;
status = "disabled";
};
lpc: lpc@1e789000 {
compatible = "aspeed,ast2600-lpc-v2", "simple-mfd", "syscon";
reg = <0x1e789000 0x1000>;
reg-io-width = <4>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x1e789000 0x1000>;
kcs1: kcs@24 {
compatible = "aspeed,ast2500-kcs-bmc-v2";
reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>;
interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
kcs_chan = <1>;
status = "disabled";
};
kcs2: kcs@28 {
compatible = "aspeed,ast2500-kcs-bmc-v2";
reg = <0x28 0x1>, <0x34 0x1>, <0x40 0x1>;
interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
status = "disabled";
};
kcs3: kcs@2c {
compatible = "aspeed,ast2500-kcs-bmc-v2";
reg = <0x2c 0x1>, <0x38 0x1>, <0x44 0x1>;
interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
status = "disabled";
};
kcs4: kcs@114 {
compatible = "aspeed,ast2500-kcs-bmc-v2";
reg = <0x114 0x1>, <0x118 0x1>, <0x11c 0x1>;
interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
status = "disabled";
};
lpc_ctrl: lpc-ctrl@80 {
compatible = "aspeed,ast2600-lpc-ctrl";
reg = <0x80 0x80>;
clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
status = "disabled";
};
lpc_snoop: lpc-snoop@80 {
compatible = "aspeed,ast2600-lpc-snoop";
reg = <0x80 0x80>;
interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
status = "disabled";
};
lhc: lhc@a0 {
compatible = "aspeed,ast2600-lhc";
reg = <0xa0 0x24 0xc8 0x8>;
};
lpc_reset: reset-controller@98 {
compatible = "aspeed,ast2600-lpc-reset";
reg = <0x98 0x4>;
#reset-cells = <1>;
};
uart_routing: uart-routing@98 {
compatible = "aspeed,ast2600-uart-routing";
reg = <0x98 0x8>;
status = "disabled";
};
ibt: ibt@140 {
compatible = "aspeed,ast2600-ibt-bmc";
reg = <0x140 0x18>;
interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
status = "disabled";
};
};
sdc: sdc@1e740000 {
compatible = "aspeed,ast2600-sd-controller";
reg = <0x1e740000 0x100>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x1e740000 0x10000>;
clocks = <&syscon ASPEED_CLK_GATE_SDCLK>;
status = "disabled";
sdhci0: sdhci@1e740100 {
compatible = "aspeed,ast2600-sdhci", "sdhci";
reg = <0x100 0x100>;
interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
sdhci,auto-cmd12;
clocks = <&syscon ASPEED_CLK_SDIO>;
status = "disabled";
};
sdhci1: sdhci@1e740200 {
compatible = "aspeed,ast2600-sdhci", "sdhci";
reg = <0x200 0x100>;
interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
sdhci,auto-cmd12;
clocks = <&syscon ASPEED_CLK_SDIO>;
status = "disabled";
};
};
emmc_controller: sdc@1e750000 {
compatible = "aspeed,ast2600-sd-controller";
reg = <0x1e750000 0x100>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x1e750000 0x10000>;
clocks = <&syscon ASPEED_CLK_GATE_EMMCCLK>;
status = "disabled";
emmc: sdhci@1e750100 {
compatible = "aspeed,ast2600-sdhci";
reg = <0x100 0x100>;
sdhci,auto-cmd12;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_EMMC>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_emmc_default>;
};
};
vuart1: serial@1e787000 {
compatible = "aspeed,ast2500-vuart";
reg = <0x1e787000 0x40>;
reg-shift = <2>;
interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_APB1>;
no-loopback-test;
status = "disabled";
};
vuart3: serial@1e787800 {
compatible = "aspeed,ast2500-vuart";
reg = <0x1e787800 0x40>;
reg-shift = <2>;
interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_APB2>;
no-loopback-test;
status = "disabled";
};
vuart2: serial@1e788000 {
compatible = "aspeed,ast2500-vuart";
reg = <0x1e788000 0x40>;
reg-shift = <2>;
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_APB1>;
no-loopback-test;
status = "disabled";
};
vuart4: serial@1e788800 {
compatible = "aspeed,ast2500-vuart";
reg = <0x1e788800 0x40>;
reg-shift = <2>;
interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_APB2>;
no-loopback-test;
status = "disabled";
};
uart2: serial@1e78d000 {
compatible = "ns16550a";
reg = <0x1e78d000 0x20>;
reg-shift = <2>;
reg-io-width = <4>;
interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_UART2CLK>;
resets = <&lpc_reset 5>;
no-loopback-test;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_txd2_default &pinctrl_rxd2_default>;
status = "disabled";
};
uart3: serial@1e78e000 {
compatible = "ns16550a";
reg = <0x1e78e000 0x20>;
reg-shift = <2>;
reg-io-width = <4>;
interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_UART3CLK>;
resets = <&lpc_reset 6>;
no-loopback-test;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_txd3_default &pinctrl_rxd3_default>;
status = "disabled";
};
uart4: serial@1e78f000 {
compatible = "ns16550a";
reg = <0x1e78f000 0x20>;
reg-shift = <2>;
reg-io-width = <4>;
interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_UART4CLK>;
resets = <&lpc_reset 7>;
no-loopback-test;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_txd4_default &pinctrl_rxd4_default>;
status = "disabled";
};
uart6: serial@1e790000 {
compatible = "ns16550a";
reg = <0x1e790000 0x20>;
reg-shift = <2>;
reg-io-width = <4>;
interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_UART6CLK>;
no-loopback-test;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart6_default>;
status = "disabled";
};
uart7: serial@1e790100 {
compatible = "ns16550a";
reg = <0x1e790100 0x20>;
reg-shift = <2>;
reg-io-width = <4>;
interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_UART7CLK>;
no-loopback-test;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart7_default>;
status = "disabled";
};
uart8: serial@1e790200 {
compatible = "ns16550a";
reg = <0x1e790200 0x20>;
reg-shift = <2>;
reg-io-width = <4>;
interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_UART8CLK>;
no-loopback-test;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart8_default>;
status = "disabled";
};
uart9: serial@1e790300 {
compatible = "ns16550a";
reg = <0x1e790300 0x20>;
reg-shift = <2>;
reg-io-width = <4>;
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&syscon ASPEED_CLK_GATE_UART9CLK>;
no-loopback-test;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart9_default>;
status = "disabled";
};
i2c: bus@1e78a000 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x1e78a000 0x1000>;
};
fsim0: fsi@1e79b000 {
compatible = "aspeed,ast2600-fsi-master", "fsi-master";
reg = <0x1e79b000 0x94>;
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fsi1_default>;
clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
status = "disabled";
};
fsim1: fsi@1e79b100 {
compatible = "aspeed,ast2600-fsi-master", "fsi-master";
reg = <0x1e79b100 0x94>;
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fsi2_default>;
clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
status = "disabled";
};
udma: dma-controller@1e79e000 {
compatible = "aspeed,ast2600-udma";
reg = <0x1e79e000 0x1000>;
interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
dma-channels = <28>;
#dma-cells = <1>;
status = "disabled";
};
};
};
};
#include "aspeed-g6-pinctrl.dtsi"
&i2c {
i2c0: i2c-bus@80 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x80 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1_default>;
status = "disabled";
};
i2c1: i2c-bus@100 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x100 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2_default>;
status = "disabled";
};
i2c2: i2c-bus@180 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x180 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3_default>;
status = "disabled";
};
i2c3: i2c-bus@200 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x200 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c4_default>;
status = "disabled";
};
i2c4: i2c-bus@280 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x280 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c5_default>;
status = "disabled";
};
i2c5: i2c-bus@300 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x300 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c6_default>;
status = "disabled";
};
i2c6: i2c-bus@380 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x380 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c7_default>;
status = "disabled";
};
i2c7: i2c-bus@400 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x400 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c8_default>;
status = "disabled";
};
i2c8: i2c-bus@480 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x480 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c9_default>;
status = "disabled";
};
i2c9: i2c-bus@500 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x500 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c10_default>;
status = "disabled";
};
i2c10: i2c-bus@580 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x580 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c11_default>;
status = "disabled";
};
i2c11: i2c-bus@600 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x600 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c12_default>;
status = "disabled";
};
i2c12: i2c-bus@680 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x680 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c13_default>;
status = "disabled";
};
i2c13: i2c-bus@700 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x700 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c14_default>;
status = "disabled";
};
i2c14: i2c-bus@780 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x780 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c15_default>;
status = "disabled";
};
i2c15: i2c-bus@800 {
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x800 0x80>;
compatible = "aspeed,ast2600-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB2>;
resets = <&syscon ASPEED_RESET_I2C>;
interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
bus-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c16_default>;
status = "disabled";
};
};