// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2016 Andreas Färber
*/
#include "meson-gxbb.dtsi"
#include <dt-bindings/sound/meson-aiu.h>
/ {
compatible = "tronsmart,vega-s95", "amlogic,meson-gxbb";
aliases {
serial0 = &uart_AO;
ethernet0 = ðmac;
};
chosen {
stdout-path = "serial0:115200n8";
};
spdif_dit: audio-codec-0 {
#sound-dai-cells = <0>;
compatible = "linux,spdif-dit";
status = "okay";
sound-name-prefix = "DIT";
};
leds {
compatible = "gpio-leds";
led-blue {
label = "vega-s95:blue:on";
gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
default-state = "on";
panic-indicator;
};
};
usb_pwr: regulator-usb-pwrs {
compatible = "regulator-fixed";
regulator-name = "USB_PWR";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vddio_boot: regulator-vddio_boot {
compatible = "regulator-fixed";
regulator-name = "VDDIO_BOOT";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vddao_3v3: regulator-vddao_3v3 {
compatible = "regulator-fixed";
regulator-name = "VDDAO_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vddio_ao18: regulator-vddio_ao18 {
compatible = "regulator-fixed";
regulator-name = "VDDIO_AO18";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vcc_3v3: regulator-vcc_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
wifi32k: wifi32k {
compatible = "pwm-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
};
hdmi-connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_connector_in: endpoint {
remote-endpoint = <&hdmi_tx_tmds_out>;
};
};
};
sdio_pwrseq: sdio-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
clocks = <&wifi32k>;
clock-names = "ext_clock";
};
sound {
compatible = "amlogic,gx-sound-card";
model = "VEGA-S95";
assigned-clocks = <&clkc CLKID_MPLL0>,
<&clkc CLKID_MPLL1>,
<&clkc CLKID_MPLL2>;
assigned-clock-parents = <0>, <0>, <0>;
assigned-clock-rates = <294912000>,
<270950400>,
<393216000>;
dai-link-0 {
sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
};
dai-link-1 {
sound-dai = <&aiu AIU_CPU CPU_SPDIF_FIFO>;
};
dai-link-2 {
sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
dai-format = "i2s";
mclk-fs = <256>;
codec-0 {
sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
};
};
dai-link-3 {
sound-dai = <&aiu AIU_CPU CPU_SPDIF_ENCODER>;
codec-0 {
sound-dai = <&spdif_dit>;
};
};
dai-link-4 {
sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
codec-0 {
sound-dai = <&hdmi_tx>;
};
};
};
};
&aiu {
status = "okay";
pinctrl-0 = <&spdif_out_y_pins>;
pinctrl-names = "default";
};
&cec_AO {
status = "okay";
pinctrl-0 = <&ao_cec_pins>;
pinctrl-names = "default";
hdmi-phandle = <&hdmi_tx>;
};
ðmac {
status = "okay";
pinctrl-0 = <ð_rgmii_pins>;
pinctrl-names = "default";
phy-handle = <ð_phy0>;
phy-mode = "rgmii";
amlogic,tx-delay-ns = <2>;
mdio {
compatible = "snps,dwmac-mdio";
#address-cells = <1>;
#size-cells = <0>;
eth_phy0: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
reg = <0>;
reset-assert-us = <10000>;
reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
/* MAC_INTR on GPIOZ_15 */
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
};
};
};
&hdmi_tx {
status = "okay";
pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
pinctrl-names = "default";
};
&hdmi_tx_tmds_port {
hdmi_tx_tmds_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
};
};
&ir {
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
linux,rc-map-name = "rc-vega-s9x";
};
&pwm_ef {
status = "okay";
pinctrl-0 = <&pwm_e_pins>;
pinctrl-names = "default";
clocks = <&clkc CLKID_FCLK_DIV4>;
clock-names = "clkin0";
};
&saradc {
status = "okay";
vref-supply = <&vddio_ao18>;
};
/* Wireless SDIO Module */
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
pinctrl-1 = <&sdio_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <50000000>;
non-removable;
disable-wp;
/* WiFi firmware requires power to be kept while in suspend */
keep-power-in-suspend;
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
};
};
/* SD card */
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
pinctrl-1 = <&sdcard_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <50000000>;
disable-wp;
cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vcc_3v3>;
};
/* eMMC */
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
pinctrl-1 = <&emmc_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
max-frequency = <200000000>;
non-removable;
disable-wp;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
mmc-pwrseq = <&emmc_pwrseq>;
vmmc-supply = <&vcc_3v3>;
vqmmc-supply = <&vddio_boot>;
};
/* This is connected to the Bluetooth module: */
&uart_A {
status = "okay";
pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
pinctrl-names = "default";
bluetooth {
compatible = "brcm,bcm43438-bt";
shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
max-speed = <2000000>;
clocks = <&wifi32k>;
clock-names = "lpo";
};
};
/* This UART is brought out to the DB9 connector */
&uart_AO {
status = "okay";
pinctrl-0 = <&uart_ao_a_pins>;
pinctrl-names = "default";
};
&usb0_phy {
status = "okay";
phy-supply = <&usb_pwr>;
};
&usb1_phy {
status = "okay";
};
&usb0 {
status = "okay";
};
&usb1 {
status = "okay";
};