# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/mmc/nvidia,tegra20-sdhci.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: NVIDIA Tegra Secure Digital Host Controller
maintainers:
- Thierry Reding <thierry.reding@gmail.com>
- Jon Hunter <jonathanh@nvidia.com>
description: |
This controller on Tegra family SoCs provides an interface for MMC, SD, and
SDIO types of memory cards.
This file documents differences between the core properties described by
mmc-controller.yaml and the properties for the Tegra SDHCI controller.
properties:
compatible:
oneOf:
- enum:
- nvidia,tegra20-sdhci
- nvidia,tegra30-sdhci
- nvidia,tegra114-sdhci
- nvidia,tegra124-sdhci
- nvidia,tegra210-sdhci
- nvidia,tegra186-sdhci
- nvidia,tegra194-sdhci
- items:
- const: nvidia,tegra132-sdhci
- const: nvidia,tegra124-sdhci
- items:
- enum:
- nvidia,tegra194-sdhci
- nvidia,tegra234-sdhci
- const: nvidia,tegra186-sdhci
reg:
maxItems: 1
interrupts:
maxItems: 1
assigned-clocks: true
assigned-clock-parents: true
assigned-clock-rates: true
clocks:
minItems: 1
maxItems: 2
clock-names:
minItems: 1
maxItems: 2
resets:
items:
- description: module reset
reset-names:
items:
- const: sdhci
power-gpios:
description: specify GPIOs for power control
maxItems: 1
interconnects:
items:
- description: memory read client
- description: memory write client
interconnect-names:
items:
- const: dma-mem # read
- const: write
iommus:
maxItems: 1
operating-points-v2: true
power-domains:
items:
- description: phandle to the core power domain
nvidia,default-tap:
description: Specify the default inbound sampling clock trimmer value for
non-tunable modes.
The values are used for compensating trace length differences by
adjusting the sampling point. The values are programmed to the Vendor
Clock Control Register. Please refer to the reference manual of the SoC
for correct values.
The DQS trim values are only used on controllers which support HS400
timing. Only SDMMC4 on Tegra210 and Tegra186 supports HS400.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,default-trim:
description: Specify the default outbound clock trimmer value.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,dqs-trim:
description: Specify DQS trim value for HS400 timing.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,pad-autocal-pull-down-offset-1v8:
description: Specify drive strength calibration offsets for 1.8 V
signaling modes.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,pad-autocal-pull-down-offset-1v8-timeout:
description: Specify drive strength used as a fallback in case the
automatic calibration times out on a 1.8 V signaling mode.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,pad-autocal-pull-down-offset-3v3:
description: Specify drive strength calibration offsets for 3.3 V
signaling modes.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,pad-autocal-pull-down-offset-3v3-timeout:
description: Specify drive strength used as a fallback in case the
automatic calibration times out on a 3.3 V signaling mode.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,pad-autocal-pull-down-offset-sdr104:
description: Specify drive strength calibration offsets for SDR104 mode.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,pad-autocal-pull-down-offset-hs400:
description: Specify drive strength calibration offsets for HS400 mode.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,pad-autocal-pull-up-offset-1v8:
description: Specify drive strength calibration offsets for 1.8 V
signaling modes.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,pad-autocal-pull-up-offset-1v8-timeout:
description: Specify drive strength used as a fallback in case the
automatic calibration times out on a 1.8 V signaling mode.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,pad-autocal-pull-up-offset-3v3:
description: Specify drive strength calibration offsets for 3.3 V
signaling modes.
The property values are drive codes which are programmed into the
PD_OFFSET and PU_OFFSET sections of the SDHCI_TEGRA_AUTO_CAL_CONFIG
register. A higher value corresponds to higher drive strength. Please
refer to the reference manual of the SoC for correct values. The SDR104
and HS400 timing specific values are used in corresponding modes if
specified.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,pad-autocal-pull-up-offset-3v3-timeout:
description: Specify drive strength used as a fallback in case the
automatic calibration times out on a 3.3 V signaling mode.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,pad-autocal-pull-up-offset-sdr104:
description: Specify drive strength calibration offsets for SDR104 mode.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,pad-autocal-pull-up-offset-hs400:
description: Specify drive strength calibration offsets for HS400 mode.
$ref: /schemas/types.yaml#/definitions/uint32
nvidia,only-1-8v:
description: The presence of this property indicates that the controller
operates at a 1.8 V fixed I/O voltage.
$ref: /schemas/types.yaml#/definitions/flag
required:
- compatible
- reg
- interrupts
- clocks
- resets
- reset-names
allOf:
- $ref: mmc-controller.yaml
- if:
properties:
compatible:
contains:
enum:
- nvidia,tegra20-sdhci
- nvidia,tegra30-sdhci
- nvidia,tegra114-sdhci
- nvidia,tegra124-sdhci
then:
properties:
clocks:
items:
- description: module clock
else:
properties:
clocks:
items:
- description: module clock
- description: timeout clock
clock-names:
items:
- const: sdhci
- const: tmclk
required:
- clock-names
- if:
properties:
compatible:
contains:
const: nvidia,tegra210-sdhci
then:
properties:
pinctrl-names:
oneOf:
- items:
- const: sdmmc-3v3
description: pad configuration for 3.3 V
- const: sdmmc-1v8
description: pad configuration for 1.8 V
- const: sdmmc-3v3-drv
description: pull-up/down configuration for 3.3 V
- const: sdmmc-1v8-drv
description: pull-up/down configuration for 1.8 V
- items:
- const: sdmmc-3v3-drv
description: pull-up/down configuration for 3.3 V
- const: sdmmc-1v8-drv
description: pull-up/down configuration for 1.8 V
- items:
- const: sdmmc-1v8-drv
description: pull-up/down configuration for 1.8 V
required:
- clock-names
- if:
properties:
compatible:
contains:
enum:
- nvidia,tegra186-sdhci
- nvidia,tegra194-sdhci
then:
properties:
pinctrl-names:
items:
- const: sdmmc-3v3
description: pad configuration for 3.3 V
- const: sdmmc-1v8
description: pad configuration for 1.8 V
required:
- clock-names
unevaluatedProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
mmc@c8000200 {
compatible = "nvidia,tegra20-sdhci";
reg = <0xc8000200 0x200>;
interrupts = <47>;
clocks = <&tegra_car 14>;
resets = <&tegra_car 14>;
reset-names = "sdhci";
cd-gpios = <&gpio 69 0>; /* gpio PI5 */
wp-gpios = <&gpio 57 0>; /* gpio PH1 */
power-gpios = <&gpio 155 0>; /* gpio PT3 */
bus-width = <8>;
};
- |
#include <dt-bindings/clock/tegra210-car.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
mmc@700b0000 {
compatible = "nvidia,tegra210-sdhci";
reg = <0x700b0000 0x200>;
interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&tegra_car TEGRA210_CLK_SDMMC1>,
<&tegra_car TEGRA210_CLK_SDMMC_LEGACY>;
clock-names = "sdhci", "tmclk";
resets = <&tegra_car 14>;
reset-names = "sdhci";
pinctrl-names = "sdmmc-3v3", "sdmmc-1v8",
"sdmmc-3v3-drv", "sdmmc-1v8-drv";
pinctrl-0 = <&sdmmc1_3v3>;
pinctrl-1 = <&sdmmc1_1v8>;
pinctrl-2 = <&sdmmc1_3v3_drv>;
pinctrl-3 = <&sdmmc1_1v8_drv>;
nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>;
nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>;
nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>;
nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>;
nvidia,default-tap = <0x2>;
nvidia,default-trim = <0x4>;
assigned-clocks = <&tegra_car TEGRA210_CLK_SDMMC4>,
<&tegra_car TEGRA210_CLK_PLL_C4_OUT0>,
<&tegra_car TEGRA210_CLK_PLL_C4>;
assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>;
assigned-clock-rates = <200000000>, <1000000000>, <1000000000>;
};